LD1085xx 3 A low drop positive voltage regulator adjustable and fixed Features Typical dropout 1.3 V (at 3 A) Three terminal adjustable or fixed output voltage 1.5 V, 1.8 V, 2.5 V, 3.3 V, 5 V, 12 V. Automotive grade product: adjustable VOUT only in TO-220 full pack package Guaranteed output current up to 3 A Output tolerance 1 % at 25C and 2 % in full temperature range Internal power and thermal limit Wide operating temperature range -40 C to 125 C Package available: TO-220, TO-220FP, DPAK, D2PAK, D2PAK/A into the load, so increase efficiency. Only a 10 F minimum capacitor is need for stability. Pinout compatibility with standard adjustable VREG The device is supplied in TO-220, TO-220FP, DPAK, D2PAK and D2PAK/A. On chip trimming allows the regulator to reach a very tight output voltage tolerance, within 1 % at 25 C. Description The LD1085xx is a low drop voltage regulator able to provide up to 3 A of output current. Dropout is guaranteed at a maximum of 1.2 V at the maximum output current, decreasing at lower loads. The LD1085xx is pin to pin compatible with the older 3-terminal adjustable regulators, but has better performances in term of drop and output tolerance. TO-220 DPAK TO-220FP D2PAK D2PAK/A The LD1085xx is available as automotive grade in TO-220FP package only, for the option of adjustable output voltage whose commercial part number is shown in the Table 11: Order codes. This device is qualified according to the specification AEC-Q100 of the automotive market, in the temperature range -40 C to 125 C, and the statistical tests PAT, SYL, SBL are performed. A 2.85 V output version is suitable for SCSI-2 active termination. Unlike PNP regulators, where a part of the output current is wasted as quiescent current, the LD1085xx quiescent current flows Table 1. Device summary Part numbers July 2009 LD1085XX LD1085XX25 LD1085XX15 LD1085XX33 LD1085XX18 LD1085XX50 Doc ID 6738 Rev 25 1/28 www.st.com 28 Contents LD1085xx Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Schematic application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 8 Order codes 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2/28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Doc ID 6738 Rev 25 LD1085xx Diagram 1 Diagram Figure 1. Schematic diagram Doc ID 6738 Rev 25 3/28 Pin configuration LD1085xx 2 Pin configuration Figure 2. Pin connections (top view) TO-220 TO-220FP D2PAK D2PAK/A DPAK 4/28 Doc ID 6738 Rev 25 LD1085xx Maximum ratings 3 Maximum ratings Table 2. Absolute maximum ratings Symbol Parameter Value Unit 30 V VI DC input voltage IO Output current Internally limited mA PD Power dissipation Internally limited mW TSTG Storage temperature range -55 to +150 C TOP Operating junction temperature range -40 to +125 C Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied Table 3. Thermal data Symbol Parameter TO-220 TO-220FP DPAK D2PAK D2PAK/A Unit RthJC Thermal resistance junction-case 3 5 8 3 C/W RthJA Thermal resistance junction-ambient 50 60 100 62.5 C/W Doc ID 6738 Rev 25 5/28 Schematic application LD1085xx 4 Schematic application Figure 3. Application circuit R V O = V REF 1 + ------2- R 1 6/28 Doc ID 6738 Rev 25 LD1085xx 5 Electrical characteristics Electrical characteristics VI = 4.5 V, CI = CO =10 F, TA = -40 to 125 C, unless otherwise specified. Table 4. Symbol Electrical characteristics of LD1085#15 Parameter Test condition Min. Typ. Max. Unit IO = 0 mA, TJ = 25C 1.485 1.5 1.515 V IO = 0 to 3 A, VI = 3.1 to 30 V 1.47 1.5 1.53 V IO = 0 mA, VI = 3.1 to 18 V, TJ = 25C 0.2 4 mV IO = 0 mA, VI = 3.1 to 15 V 0.4 4 mV IO = 0 to 3 A, TJ = 25C 2 10 mV IO = 0 to 3 A 4 20 mV 1.3 1.5 V 5 10 mA VO Output voltage (1) VO Line regulation VO Load regulation Vd Dropout voltage IO =3 A Iq Quiescent current VI 30 V Isc Short circuit current SVR eN VI - VO = 5 V 3.2 4.5 A VI - VO = 25 V 0.2 0.5 A Thermal regulation TA = 25C, 30ms pulse Supply voltage rejection f = 120 Hz, CO = 25 F, IO = 3 A VI = 7.5 3 V RMS output noise voltage (% of VO) TA = 25C, f =10 Hz to 10 kHz S Temperature stability S Long term stability TA = 125C, 1000Hrs 0.008 60 0.04 %/W 72 dB 0.003 % 0.5 % 0.5 % 1. See short-circuit current curve for available output current at fixed dropout. Doc ID 6738 Rev 25 7/28 Electrical characteristics LD1085xx VI = 4.8 V, CI = CO =10 F, TA = -40 to 125 C, unless otherwise specified. Table 5. Symbol Electrical characteristics of LD1085#18 Parameter Test condition Min. Typ. Max. Unit IO = 0 mA, TJ = 25C 1.782 1.8 1.818 V IO = 0 to 3 A, VI = 3.4 to 30 V 1.764 1.8 1.836 V IO = 0 mA, VI = 3.4 to 18 V TJ = 25C 0.2 4 mV IO = 0 mA, VI = 3.4 to 15 V 0.4 4 mV IO = 0 to 3 A, TJ = 25C 2 10 mV IO = 0 to 3 A 4 20 mV VO Output voltage (1) VO Line regulation VO Load regulation Vd Dropout voltage IO = 3 A 1.3 1.5 V Iq Quiescent current VI 30 V 5 10 mA Isc Short circuit current SVR eN VI - VO = 5 V 3.2 4.5 A VI - VO = 25 V 0.2 0.5 A Thermal regulation TA = 25C, 30 ms pulse Supply voltage rejection f = 120 Hz, CO = 25 F, IO = 3 A VI = 7.5 3 V RMS output noise voltage (% of TA = 25C, f =10 Hz to 10 kHz VO) S Temperature stability S Long term stability TA = 125C, 1000 Hrs 1. See short-circuit current curve for available output current at fixed dropout. 8/28 Doc ID 6738 Rev 25 0.008 60 0.04 %/W 72 dB 0.003 % 0.5 % 0.5 % LD1085xx Electrical characteristics VI = 5.5 V, CI = CO =10 F, TA = -40 to 125 C, unless otherwise specified. Table 6. Symbol Electrical characteristics of LD1085#25 Parameter Test condition Min. Typ. Max. Unit IO = 0 mA, TJ = 25C 2.475 2.5 2.525 V IO = 0 to 3 A, VI = 4.1 to 30 V 2.45 2.5 2.55 V IO = 0 mA, VI = 4.1 to 18 V, TJ = 25C 0.2 4 mV IO = 0 mA, VI = 4.1 to 18 V 0.4 4 mV IO = 0 to 3 A, TJ = 25C 2 10 mV IO = 0 to 3 A 4 20 mV VO Output voltage (1) VO Line regulation VO Load regulation Vd Dropout voltage IO = 3 A 1.3 1.5 V Iq Quiescent current VI 30 V 5 10 mA Isc Short circuit current SVR eN VI - VO = 5 V 3.2 4.5 A VI - VO = 25 V 0.2 0.5 A Thermal regulation TA = 25C, 30ms pulse Supply voltage rejection f = 120 Hz, CO = 25F, IO = 3 A VI = 7.5 3 V RMS output noise voltage (% of VO) TA = 25C, f =10 Hz to 10 kHz S Temperature stability S Long term stability TA = 125C, 1000 Hrs 0.008 60 0.04 %/W 72 dB 0.003 % 0.5 % 0.5 % 1. See short-circuit current curve for available output current at fixed dropout. Doc ID 6738 Rev 25 9/28 Electrical characteristics LD1085xx VI = 6.3 V, CI = CO =10 F, TA = -40 to 125 C, unless otherwise specified. Table 7. Symbol Electrical characteristics of LD1085#33 Parameter Test condition Min. Typ. Max. Unit IO = 0 mA, TJ = 25C 3.267 3.3 3.333 V IO = 0 to 3 A, VI = 4.9 to 30 V 3.234 3.35 3.366 V 0.5 6 mV IO = 0 mA, VI = 4.9 to 18 V 1 6 mV IO = 0 to 3 A, TJ = 25C 3 15 mV IO = 0 to 3 A 7 20 mV VO Output voltage (1) VO Line regulation VO Load regulation Vd Dropout voltage IO = 3 A 1.3 1.5 V Iq Quiescent current VI 30 V 5 10 mA Isc Short circuit current SVR eN IO = 0 mA, VI = 4.9 to 18 V, TJ = 25C VI - VO = 5 V 3.2 4.5 A VI - VO = 25 V 0.2 0.5 A Thermal regulation TA = 25C, 30 ms pulse Supply voltage rejection f = 120 Hz, CO = 25 F, IO = 3 A VI = 8.3 3 V RMS output noise voltage (% of VO) TA = 25C, f =10 Hz to 10 kHz S Temperature stability S Long term stability TA = 125C, 1000 Hrs 1. See short-circuit current curve for available output current at fixed dropout. 10/28 Doc ID 6738 Rev 25 0.008 60 0.04 %/W 72 dB 0.003 % 0.5 % 0.5 % LD1085xx Electrical characteristics VI = 8 V, CI = CO =10 F, TA = -40 to 125 C, unless otherwise specified. Table 8. Symbol Electrical characteristics of LD1085#50 Parameter Test condition Min. Typ. Max. Unit IO = 0 mA, TJ = 25C 4.95 5 5.05 V IO = 0 to 3 A, VI = 6.6 to 30 V 4.9 5 5.1 V 0.5 10 mV IO = 0 mA, VI = 6.6 to 20 V 1 10 mV IO = 0 to 3 A, TJ = 25C 5 10 mV IO = 0 to 3 A 10 35 mV VO Output voltage (1) VO Line regulation VO Load regulation Vd Dropout voltage IO = 3 A 1.3 1.5 V Iq Quiescent current VI 30 V 5 10 mA Isc Short circuit current SVR eN IO = 0 mA, VI = 6.6 to 20 V, TJ = 25C VI - VO = 5 V 3.2 4.5 A VI - VO = 25 V 0.2 0.5 A Thermal regulation TA = 25C, 30 ms pulse Supply voltage rejection f = 120 Hz, CO = 25 F, IO = 3 A VI = 10 3 V RMS output noise voltage (% of VO) TA = 25C, f = 10 Hz to 10 kHz S Temperature stability S Long term stability TA = 125C, 1000 Hrs 0.008 60 0.04 %/W 72 dB 0.003 % 0.5 % 0.5 % 1. See short-circuit current curve for available output current at fixed dropout. Doc ID 6738 Rev 25 11/28 Electrical characteristics LD1085xx VI = 4.25 V, CI = CO =10 F, TA = -40 to 125 C, unless otherwise specified. Table 9. Symbol Electrical characteristics of LD1085# Parameter VO Output voltage (1) VO Line regulation Test condition Min. Typ. Max. Unit IO = 10 mA TJ = 25C 1.237 1.25 1.263 V IO = 10 mA to 3 A, VI = 2.85 to 30 V 1.225 1.25 1.275 V IO = 10 mA, VI = 2.85 to 16.5 V, TJ = 25C 0.015 0.2 % IO = 10 mA, VI = 2.85 to 16.5 V 0.035 0.2 % IO = 10 mA to 3 A, TJ = 25C 0.1 0.3 % IO = 0 to 3 A 0.2 0.4 % VO Load regulation Vd Dropout voltage IO = 3 A 1.3 1.5 V Minimum load current VI = 30 V 3 10 mA IO(min) Isc Short circuit current VI - VO = 5 V 5.5 6.5 A VI - VO = 25 V 0.5 0.7 A Thermal regulation TA = 25C, 30ms pulse SVR Supply voltage rejection f = 120 Hz, CO = 25 F,CADJ = 25 F, IO = 3 A, VI = 6.25 3 V IADJ Adjust pin current IADJ eN Adjust pin current change (1) RMS output noise voltage (% of VO) S Temperature stability S Long term stability 60 72 %/W dB VI = 4.25 V, IO = 10 mA 55 120 A IO = 10 mA to 3 A, VI = 2.85 to 16.5 V 0.2 5 A TA = 25C, f =10 Hz to 10 kHz TA = 125C, 1000 Hrs 1. See short-circuit current curve for available output current at fixed dropout. 12/28 0.003 0.015 Doc ID 6738 Rev 25 0.003 % 0.5 % 0.5 % LD1085xx Electrical characteristics VI = 4.25 V, CI = CO =10 F, TA = -40 to 125 C, unless otherwise specified. Table 10. Symbol Electrical characteristics of LD1085PY (Automotive Grade) Parameter Test condition Min. Typ. Max. Unit IO = 10 mA TA = 25C 1.237 1.25 1.263 V IO = 10 mA to 3 A, VI = 2.85 to 30 V 1.225 1.25 1.275 V 0.035 0.2 % VO Output voltage (1) VO Line regulation IO = 10 mA, VI = 2.85 to 16.5 V VO Load regulation IO = 0 to 3 A 0.2 0.4 % Vd Dropout voltage IO = 3 A 1.3 1.5 V Minimum load current VI = 30 V 3 10 mA IO(min) Isc Short circuit current VI - VO = 5 V, TA = 25C 5.5 6.5 A VI - VO = 25 V, TA = 25C 0.5 0.7 A Thermal regulation TA = 25C, 30 ms pulse SVR Supply voltage rejection f = 120 Hz, CO = 25 F,CADJ = 25 F, IO = 3 A, VI = 6.25 3 V, TA = 25C IADJ Adjust pin current VI = 4.25 V, IO = 10 mA 55 120 A IADJ Adjust pin current change (1) IO = 10 mA to 3 A, VI = 2.85 to 16.5 V 0.2 5 A eN RMS output noise voltage (% of VO) TA = 25C, f =10 Hz to 10 kHz S Temperature stability S Long term stability TA = 125C, 1000 Hrs 0.003 0.015 60 72 %/W dB 0.003 % 0.5 % 0.5 % 1. See short-circuit current curve for available output current at fixed dropout. Doc ID 6738 Rev 25 13/28 Typical application 6 LD1085xx Typical application Unless otherwise specified TJ = 25 C, CI = CO = 10 F. Figure 4. Output voltage vs. temperature Figure 5. Output voltage vs. temperature Figure 6. Output voltage vs. temperature Figure 7. Short circuit current vs. dropout voltage Figure 8. Line regulation vs. temperature Figure 9. Load regulation vs. temperature 14/28 Doc ID 6738 Rev 25 LD1085xx Typical application Figure 10. Dropout voltage vs. temperature Figure 11. Dropout voltage vs. output current Figure 12. Adjust pin current vs. temperature Figure 13. Quiescent current vs. temperature Figure 14. Line regulation vs. temperature Figure 15. Supply voltage rejection vs. output current Doc ID 6738 Rev 25 15/28 Typical application LD1085xx Figure 16. Supply voltage rejection vs. frequency Figure 17. Supply voltage rejection vs. temperature Figure 18. Minimum load current vs. temperature Figure 19. Stability, VO = 1.8 V Figure 20. Stability, VO = 12 V Figure 21. Line transient VI=12 to 13V, IO=200mA, CI = 1F(tant), CO=10F(tant), CADJ=1F 16/28 Doc ID 6738 Rev 25 LD1085xx Typical application Figure 22. Line transient Figure 23. Load transient VI=12 to 13V, IO=200mA, CI = 1F(tant), CO=10F(tant), CADJ=1F VI=12V, IO=0.12 to 3A, CI = 1F(tant), CO=10F(tant), CADJ=1F Figure 24. Load transient VI=12V, IO=0.12 to 3A, CI = 1F(tant), CO=10F(tant), CADJ=1F Doc ID 6738 Rev 25 17/28 Package mechanical data 7 LD1085xx Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. 18/28 Doc ID 6738 Rev 25 LD1085xx Package mechanical data TO-220 mechanical data Dim. mm. Min. Typ. inch. Max. Min. Typ. Max. A 4.40 4.60 0.173 0.181 C 1.23 1.32 0.048 0.051 D 2.40 2.72 0.094 0.107 0.70 0.019 0.027 D1 E 1.27 0.49 0.050 F 0.61 0.88 0.024 0.034 F1 1.14 1.70 0.044 0.067 F2 1.14 1.70 0.044 0.067 G 4.95 5.15 0.194 0.203 G1 2.4 2.7 0.094 0.106 H2 10.0 10.40 0.393 0.409 L2 16.4 0.645 L4 13.0 14.0 0.511 0.551 L5 2.65 2.95 0.104 0.116 L6 15.25 15.75 0.600 0.620 L7 6.2 6.6 0.244 0.260 L9 3.5 3.93 0.137 0.154 DIA. 3.75 3.85 0.147 0.151 P011C Doc ID 6738 Rev 25 19/28 Package mechanical data LD1085xx TO-220FP mechanical data Dim. mm. Min. Max. Min. A 4.40 4.60 0.173 0.181 B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.70 0.017 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.50 0.045 0.059 F2 1.15 1.50 0.045 0.059 G 4.95 5.2 0.194 0.204 G1 2.4 2.7 0.094 0.106 H 10.0 10.40 0.393 0.409 L2 Typ inch. 16 Typ. Max. 0.630 L3 28.6 30.6 1.126 1.204 L4 9.8 10.6 0.385 0.417 L5 2.9 3.6 0.114 0.142 L6 15.9 16.4 0.626 0.645 L7 9 9.3 0.354 0.366 DIA. 3 3.2 0.118 0.126 7012510A-H 20/28 Doc ID 6738 Rev 25 LD1085xx Package mechanical data DPAK mechanical data mm. inch. Dim. Min. A A1 A2 B b4 C C2 D D1 E E1 e e1 H L (L1) L2 L4 R V2 Typ. 2.2 0.9 0.03 0.64 5.2 0.45 0.48 6 Max. Min. 2.4 1.1 0.23 0.9 5.4 0.6 0.6 6.2 0.086 0.035 0.001 0.025 0.204 0.017 0.019 0.236 6.6 0.252 5.1 6.4 0.260 0.173 0.368 0.039 2.8 0.8 0.181 0.397 0.110 0.031 1 0.023 0.2 0 0.094 0.043 0.009 0.035 0.212 0.023 0.023 0.244 0.185 0.090 4.6 10.1 0.6 Max. 0.200 4.7 2.28 4.4 9.35 1 Typ. 0.039 0.008 8 0 8 0068772-F Doc ID 6738 Rev 25 21/28 Package mechanical data LD1085xx D2PAK mechanical data mm. inch. Dim. Min. Typ. Max. Min. Typ. Max. A 4.4 4.6 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.6 0.017 0.023 C2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 0.368 10.4 0.393 D1 E 8 10 E1 0.315 8.5 0.409 0.335 G 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.624 L2 1.27 1.4 0.050 0.055 L3 1.4 1.75 0.055 0.068 M 2.4 3.2 0.094 R V2 0.4 0 0.126 0.016 8 0 8 P011P6G 22/28 Doc ID 6738 Rev 25 LD1085xx Package mechanical data D2PAK/A mechanical data mm. inch. Dim. Min. Typ. Max. Min. Typ. Max. A 4.40 4.60 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.028 0.037 B1 0.8 1.3 0.031 0.051 B2 1.14 1.7 0.045 0.067 C 0.45 0.60 0.018 0.024 C2 1.23 1.36 0.048 0.054 D 8.95 9.35 0.352 0.368 10.4 0.394 D1 E 8 10 E1 0.315 8.5 0.409 0.335 G 4.88 5.28 0.192 0.208 L 15 15.85 0.591 0.624 L2 1.27 1.4 0.050 0.055 M 2.4 3.2 0.094 R V2 0.4 0 0.126 0.016 8 0 8 7106164/D Doc ID 6738 Rev 25 23/28 Package mechanical data LD1085xx Tape & reel DPAK-PPAK mechanical data mm. inch. Dim. Min. Typ. A Min. Typ. 330 13.0 13.2 Max. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 24/28 Max. 0.504 0.512 22.4 0.519 0.882 Ao 6.80 6.90 7.00 0.268 0.272 0.2.76 Bo 10.40 10.50 10.60 0.409 0.413 0.417 Ko 2.55 2.65 2.75 0.100 0.104 0.105 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 7.9 8.0 8.1 0.311 0.315 0.319 Doc ID 6738 Rev 25 LD1085xx Package mechanical data Tape & reel D2PAK-P2PAK-D2PAK/A-P2PAK/A mechanical data mm. inch. Dim. Min. Typ. A Max. Min. Typ. 180 13.0 7.086 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 Max. 0.504 0.512 14.4 0.519 0.567 Ao 10.50 10.6 10.70 0.413 0.417 0.421 Bo 15.70 15.80 15.90 0.618 0.622 0.626 Ko 4.80 4.90 5.00 0.189 0.193 0.197 Po 3.9 4.0 4.1 0.153 0.157 0.161 P 11.9 12.0 12.1 0.468 0.472 0.476 Doc ID 6738 Rev 25 25/28 Order codes LD1085xx 8 Order codes Table 11. Order codes Packages TO-220 TO-220FP D2 PAK DPAK (T&R) 2 D PAK/A (T&R) LD1085DT15R LD1085D2T33R 1.5 V LD1085D2M18R 1.8 V LD1085D2M25R 2.5 V LD1085D2M33R 3.3 V LD1085V50 LD1085V 5.0 V LD1085P LD1085PY LD1085D2T-R (1) LD1085D2M-R ADJ ADJ 1. Automotive Grade products. 26/28 Output voltage Doc ID 6738 Rev 25 LD1085xx Revision history 9 Revision history Table 12. Document revision history Date Revision Changes 07-Oct-2004 12 Mistake order codes - Table 1. 08-Feb-2005 13 Mistake U.M. load regulation - V ==> mV. 01-Mar-2005 14 Version 1.2 V removed. 22-May-2006 15 Order codes has been updated and new template. 10-Nov-2006 16 Add package DPAK, typo on VO test value in tables 3, 4 and 11. 04-Apr-2007 17 Order codes updated. 07-Jun-2007 18 Order codes updated. 05-Dec-2007 19 Modified: Table 11. 29-Jan-2008 20 Added new order codes for Automotive grade products see Table 11 on page 26. 18-Feb-2008 21 Modified: Table 11 on page 26. 09-Apr-2008 22 Modified: Table 11 on page 26. 14-Jul-2008 23 Modified: Table 11 on page 26. 22-Aug-2008 24 Modified: Table 3 on page 5. 28-Jul-2009 25 Modified: Table 11 on page 26. Doc ID 6738 Rev 25 27/28 LD1085xx Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 28/28 Doc ID 6738 Rev 25