P9
www.vishay.com Vishay Sfernice
Revision: 04-Jul-17 1Document Number: 51047
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
9 mm Multi-Ganged Potentiometer
FEATURES
• Conductive plastic element
• Ultra compact (extra miniature module size)
• Multiple assemblies (up to seven modules)
• Shaft and panel sealed option
• Center mechanical detent fully integrated in option
• Center tap option
• Custom designs available on request
• Test according to CECC 41000 or IEC 60393-1
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
QUICK REFERENCE DATA
Multiple module Up to 7 modules
Switch module n/a
Detent module Yes
Special
electrical laws
A: linear, L: logarithmic, F: reverse logarithmic
and others see specification
Sealing level IP 64
Lifespan 25K cycles
DIMENSIONS in millimeters (inches) ± 0.5 mm (± 0.02")
Vertical Mounting Center Tap
Center Tap and Vertical Mounting
M7 x 0.75
0.9
(0.04)
11.35
(0.45)
2.5
(0.10)
L: See Shaft table
7
(0.276)
5
(0.20)
6.4
(0.25)
2.5
(0.10)
3.6
(0.14) 2.5
(0.10)
1
(0.04)
0.45
(0.02)
R
9.5
(0.37)
3.5
(0.14)
2.5
(0.10)
2.5
(0.10)
P9
3
3.45
(0.14)
See Shaft table
2.5
(0.10)
7.5
(0.30)
4.7
(0.19)
3.8
(0.15)
See Bushing table
7.5
(0.30)
2.5
(0.10)
2.5
(0.10)
3 x
0.9
(0.04)
2.5
(0.10)
3.5
(0.14)
2
(0.08)
2.5
(0.10)
2.5
(0.10)
2.5
(0.10)
0.2
(0.01)
5.6
(0.22)
7.9
(0.31)
P9
www.vishay.com Vishay Sfernice
Revision: 04-Jul-17 2Document Number: 51047
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
GENERAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
Resistive element Conductive plastic
Electrical travel 270° ± 10°
Power rating chart
Circuit diagram
Taper
Resistance range Linear taper 1 kΩ to 1 MΩ
Non-linear taper 2.2 kΩ to 500 kΩ
Tolerance Standard
On request
20 %
10 %
Power rating at 70 °C
Linear Taper 0.1 W
Non-Linear Taper 0.05 W
Multiple assemblies linear taper 0.05 W per module
Multiple assemblies non-linear
taper 0.025 W per module
Temperature coefficient (typical) ± 500 ppm
Limiting element voltage 10 VDC
50 VAC
End resistance (typical) 3 Ω
Contact resistance variation Linear law (typical) 2 % of nominal resistance
Independent linearity Linear law (typical) ± 5 %
Insulation resistance 100 MΩ at 250 VDC
Dielectric strength 300 VAC during 1 min
Attenuation (typical) 90 dB max./0.05 dB min.
0.1
0.05
0010 20 30 40 50 60 70 80 90 100 110 120 130
AMBIENT TEMPERATURE (°C)
RATED POWER (W)
Linear Taper
Non Linear Taper
a c
b cw
(2)
(3)
(1)
R
F S
W
L
A
90 %
50 %
20 %
10 %
Vs
%
Ve
15°
15°
Mechanical travel 300°
Electrical travel 270°
50 %
P9
www.vishay.com Vishay Sfernice
Revision: 04-Jul-17 3Document Number: 51047
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Note
• Nothing stated herein shall be construed as a guarantee of quality or durability
MECHANICAL SPECIFICATIONS
Mechanical travel 25 000 cycles min.
Mechanical travel 300° ± 5
Operating torque 0.2 Ncm to 1.5 Ncm
(0.3 oz.-inch to 1.8 oz.-inch)
End stop torque 50 Ncm max. (4.4 lb-inch max.)
Shaft push/pull force 7 DaNcm max. (15.7 lbf max.)
Weight (one module) 6.25 g (without nut and washer)
(0.22 oz.)
ENVIRONMENTAL SPECIFICATIONS
Temperature range -55 °C to +100 °C
Climatic category 55/100/21
Sealing IP 64
MARKING
• Code for tolerance
• Code for ohmic value
•Taper
• Code for date code
PACKAGING
• Box of 25 pieces
• Box of 100 pieces
PERFORMANCE
TESTS CONDITIONS
TYPICAL VALUE AND DRIFTS
ΔRT/RT (%) ΔR1-2/R1-2 (%) OTHER
Electrical endurance 1000 h at rated power
90'/30' - ambient temp. 70 °C ± 5 % ± 10 % Contact resistance variation
< 5 % Rn
Damp heat, steady state
21 days
at 40 °C ± 2 °C and 90 % to 95 %
relative humidity
± 5 % - Insulation resistance
> 10 MΩ
Change of temperature
Ambient temperature
-55 °C to +100 °C
5 cycles
± 0.5 % - -
Mechanical endurance
25 000 cycles at rated power
90 % of electrical travel
16 cycles per minute
Temperature: 20 °C
± 6 % - Contact resistance variation
± 12 %
Shock 50 g’s, 11 ms
3 shocks - 3 directions ± 0.2 % ± 0.5 % -
Vibration
10 Hz to 55 Hz
0.75 mm or 10 g’s
6 h
± 0.2 % - ΔV1-2/V1-3
± 0.5 %
P9
www.vishay.com Vishay Sfernice
Revision: 04-Jul-17 4Document Number: 51047
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ORDERING INFORMATION (Part Number)
MODEL
NUMBER
OF
MODULES
BUSHING LOCATING
PEG
PANEL
SEALED
DETENT
OPTION SHAFT PIN
STYLE
RESISTANCE CODE/
TOLERANCE CODE/
TAPER
P9A 1 to 7 R = M7 x
0.75 mm
to 7 mm
X = M7 x
0.75 mm
to 5 mm
BUSHING
X: Bushing R: Bushing • Nut tightening torque M7 bushing 120 Ncm max.
(10.6 lb-inch max.)
• Nut and washer are delivered in standard packaging
5
(0.20)
M7 x 0.75
7
(0.28)
M7 x 0.75 10
M7 x 0.75
2
0.7
R100F I R 1 0 MAP 19 X13A
P9
www.vishay.com Vishay Sfernice
Revision: 04-Jul-17 5Document Number: 51047
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Note
(1) For X bushing (16 mm)
ORDERING INFORMATION (Part Number)
MODEL
NUMBER
OF
MODULES
BUSHING LOCATING
PEG
PANEL
SEALED
DETENT
OPTION SHAFT PIN
STYLE
RESISTANCE CODE/
TOLERANCE CODE/
TAPER
0 = without
1 = with
0 = without
P = with
0 =
without
M = center
detent
See
code
below
LOCATING PEG
ADVISED PANEL CUT OUT
(including peg option)
DETENT OPTION
• Stable position and
in Mid mechanical travel
• Rotational life:
10 000 actuations
2
(0.08) 0.8
(0.03) 0.8
(0.03)
5.6
(0.22)
6 (0.24)
Ø 6.9 (0.27)
Ø 2.2 (0.09)
Full CW Full CCW
PANEL SEALED
• Only for R and X bushing without locating peg
• Front mounting surface with panel sealed option is:
6.2 mm ± 0.5 mm length for R bushing and 4.2 mm ± 0.5 mm
length for X bushing
• The ring is delivered with nut and washer
• The seal should be placed between panel and body.
Sealing is obtained by tightening the seal against the panel
when mounting the potentiometer
Tightening torque 50 Ncm up to 100 Ncm
• Advised panel hole dimensions:
Ø 6.9
(0.27)
For shaft
diam.
3.5 or 6
2.35
(0.09)
4.7
(0.19)
Ø 6.9
(0.27)
Only for
shaft diam. 3.5
SHAFT DIAMETER - FMS - STYLE
L (mm) 15 20 25 30
Style Round Slotted Flat Knurled Round Slotted Flat Round Slotted Flat Round Slotted Flat
Ø 3.5 DFR DFS DFF - DIR DIS DIF DLR DLS DLF DMR DMS DMF
Ø 6 FFR FFS FFF FGK (1) FIR FIS FIF FLR FLS FLF FMR FMS FMF
Round Slotted Flat Knurled
P1 Ø 3.5 mm = 2.5 mm
Ø 6 mm = 4.5 mm
P2 L = 15 mm → 7 mm
L > 15 mm → 12 mm
L
Ø
1
(0.039) 0.5
(0.020)
0.5
(0.020)
1.6
(0.06)
For D diameter: Ø 4.7 mm
For F diameter: Ø 6 mm
Ø
L
P2
P1
1
(0.039)
20°
90°
6
(0.236)
5
(0.197)
18 teeth
R100F I R 1 0 MAP 19 X13A
P9
www.vishay.com Vishay Sfernice
Revision: 04-Jul-17 6Document Number: 51047
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ORDERING INFORMATION (Part Number)
MODEL
NUMBER
OF
MODULES
BUSHING LOCATING
PEG
PANEL
SEALED
DETENT
OPTION SHAFT PIN
STYLE
RESISTANCE CODE/
TOLERANCE CODE/
TAPER
See Pin table
First digit:
pin type
X, J, S, Z, P, L W or N
Second digit:
pin configuration
1, 2, 3, 4 or N
PIN STYLE - HORIZONTAL MOUNTING
PIN TYPE
XPC mount
JPC mount center tap
SSoldering style
ZCenter tap soldering style
LLong pin
PCenter tap with long pin
NN If different types of pin style in the same potentiometer
PIN CONFIGURATION
12 3
2.5 mm between gang 2.5 mm - 5 mm - 2.5 mm between gang 5 mm between gang
3.5
(0.14)
3.5
(0.14)
11.5
(0.45)
7 x 2.5
(0.098) 2.5
(0.098)
2.5
(0.098)
2.5
(0.098)
7 x 2.5
(0.098) 2.5
(0.098)
2.5
(0.098)
2.5
(0.098)
7 x 2.5
(0.098) 2.5
(0.098)
2.5
(0.098)
2.5
(0.098)
R100F I R 1 0 MAP 19 X13A
P9
www.vishay.com Vishay Sfernice
Revision: 04-Jul-17 7Document Number: 51047
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ORDERING INFORMATION (Part Number)
MODEL
NUMBER
OF
MODULES
BUSHING LOCATING
PEG
PANEL
SEALED
DETENT
OPTION SHAFT PIN
STYLE
RESISTANCE CODE/
TOLERANCE CODE/
TAPER
See Pin table
First digit:
pin type
X, J, S, Z, P, L W or N
Second digit:
pin configuration
1, 2, 3, 4 or N
PIN STYLE - VERTICAL MOUNTING
W1 Single gang vertical
mounting
W2 Dual gang vertical
mounting
W3 Single gang with center
tap vertical mounting
W4 Dual gang with center
tap vertical mounting
4.7
(0.19)
10.8
(0.43)
3.8
(0.15)
7.5
(0.3) 2.5
(0.098)
2.5
(0.098)
W1 - W3
7.5
(0.3) 2.5
(0.098)
2.5
(0.098)
W2 - W4
R100F I R 1 0 MAP 19 X13A
P9
www.vishay.com Vishay Sfernice
Revision: 04-Jul-17 8Document Number: 51047
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ORDERING INFORMATION (part number)
MODEL
NUMBER
OF
MODULES
BUSHING LOCATING
PEG
PANEL
SEALED
DETENT
OPTION SHAFT PIN
STYLE
RESISTANCE CODE/
TOLERANCE CODE/
TAPER
Resistance code:
102 = 1 kΩ to
105 = 1 MΩ
Tolerance code:
standard: M = ± 20 %
on request: K = ± 10 %
taper: A, L, W, F, S, R
or
special code
given by Vishay
SPECIAL CODES GIVEN BY VISHAY
•Custom shaft
•Design on request
• Specific linearity
• Specific interlinearity
• Specific variation law
PART NUMBER DESCRIPTION (for information only)
P9A 1 R 1 0 0 FI R X1 10K 20 % A e3
MODEL MODULES BUSHING LOCATING
PEG
SEALING
OPTIONS
DETENT
OPTIONS SHAFT SHAFT LEADS VALUE TOL. TAPER SPECIAL SPECIAL
LEAD
(Pb)-
FREE
RELATED DOCUMENTS
APPLICATION NOTES
Potentiometers and Trimmers www.vishay.com/doc?51001
Guidelines for Vishay Sfernice Resistive and Inductive Components www.vishay.com/doc?52029
R100F I R 1 0 MAP 19 X13A
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 08-Feb-17 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
