LM27951 LM27951 White LED Adaptive 1.5X/1X Switched Capacitor Current Driver Literature Number: SNVS416A LM27951 White LED Adaptive 1.5X/1X Switched Capacitor Current Driver General Description Features The LM27951 is a switched capacitor white-LED driver capable of driving up to 4 LEDs with 30mA through each LED. Its 4 tightly regulated current sources ensure excellent LED current and brightness matching. LED drive current is programmed by an external sense resistor. The LM27951 operates over an input voltage range from 2.8V to 5.5V and requires only four low-cost ceramic capacitors. n n n n n n n n n n The LM27951 provides excellent efficiency without the use of an inductor by operating the charge pump in a gain of 3/2, or in a gain of 1. Maximum efficiency is achieved over the input voltage range by actively selecting the proper gain based on the LED forward voltage requirements. The LM27951 uses constant frequency pre-regulation to minimize conducted noise on the input. It has a fixed 750kHz switching frequency optimized for portable applications. The LM27951 consumes less than 1A of supply current when shut down. The LM27951 is available in a 14-pin No-Pullback Leadless Leadframe Package: LLP-14. Drives up to 4 LEDs with up to 30mA each Regulated current sources with 0.2%(typ.) matching 3/2x, 1x Gain transition based on LED VF Peak Efficiency Over 85% Input Voltage Range: 2.8V to 5.5V PWM Brightness Control Very Small Solution Size - NO INDUCTOR Fixed 750kHz Switching Frequency < 1A Shutdown Current 14-pin LLP Package: 4.0mm X 3.0mm X 0.8mm Applications n White LED Display Backlights n White LED Keypad Backlights n General Purpose LED Lighting Typical Application Circuit 20171701 (c) 2006 National Semiconductor Corporation DS201717 www.national.com LM27951 White LED Adaptive 1.5X/1X Switched Capacitor Current Driver November 2005 LM27951 Connection Diagram LM27951 14-pin No-Pullback Leadless Leadframe Package (LLP-14) 4mm x 3mm x 0.8mm NS Package Number SDA14A 20171702 Pin Descriptions Pin Name 1 C2+ Flying Capacitor C2 Connection Description 2 VOUT Pre-Regulated Charge Pump Output 3 C1+ Flying Capacitor C1 Connection 4 D4 Regulated Current Source Output. 5 D3 Regulated Current Source Output. 6 D2 Regulated Current Source Output. 7 D1 Regulated Current Source Output. 8 ISET Current Set Input. Placing a resistor (RSET) between this pin and GND sets the LED current for all the LEDs. LED Current = 200 x (1.25V / RSET). 9 EN Enable Logic Input Pin. Logic Low = Shut Down, Logic High = Enabled. There is a 150k (typ.) resistor connected internally between the EN pin and GND. 10 PWM Current Source Modulation Logic Input Pin. Logic Low = Off, Logic High = On. Applying a Pulse Width Modulated (PWM) signal to this pin allows the regulated current sources to be modulated without shutting down the internal Charge Pump and the VOUT node. 11 VIN Input Supply Range: 2.8V to 5.5V. 12 C2- Flying Capacitor C2 Connection. 13 GND 14 C1- Power Supply Ground Connection. Flying Capacitor C1 Connection. Ordering Information Order Number Package Description Package Marking Supplied as Tape and Reel (Units) LM27951SD No-Pullback LLP-14 XXXXX = Z2X YYYYY = D006B 1000 LM27951SDX www.national.com 2 4500 Operating Ratings (Notes 2, 7) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. -0.3V to 6.0V VIN EN, PWM -0.3V to (VIN + 0.3V) w/ 6.0V max Continuous Power Dissipation (Note 3) Junction Temperature Range (TJ) -40C to +115C Ambient Temperature Range (TA) (Note 5) -40C to +85 C Junction-to-Ambient Thermal Resistance, LLP-14 Package (JA) (Note 6) 150C Storage Temperature Range 2.8V to 5.5V 2.5V to 3.9V Thermal Information Internally Limited Junction Temperature (TJ-MAX-ABS) Input Voltage VIN LED Voltage Range 45C/W -65C to 150C Lead Temp. (Soldering, 5 sec.) 260C ESD Rating (Note 4) Human Body Model 2kV Electrical Characteristics (Notes 2, 7) Limits in standard typeface are for TA = 25C, and limits in boldface type apply over the full operating junction temperature range (-40C to +85 C). Unless otherwise noted, specifications apply to the LM27951 Typical Application Circuit (pg.1) with VIN = 3.6V, V(EN) = 1.8V, V(PWM) = 1.8V, 4 LEDs, VDX = 3.6V, CIN = COUT = 3.3F, C1 = C2 = 1F, RSET = 12.5k (Note 8) Symbol IDX Parameter LED Current Regulation Conditions 3.0V VIN 5.5V RSET = 12.5k IVOUT = 0mA Min Typ Max Units 18.4 (-8%) 20 21.6 (+8%) mA 3.0V VIN 5.5V RSET = 8.32k IVOUT = 0mA 30 3.0V VIN 5.5V RSET = 24.9k IVOUT = 0mA 10 ID-MATCH LED Current Matching (Note 9) RSET = 8.32k 0.2 1.5 % IQ Quiescent Supply Current D(1-4) = OPEN RSET = OPEN 1.5 1.9 mA ISD Shutdown Supply Current 3.0V VIN 5.5V V(EN) = 0V 0.1 1 A VSET ISET Pin Voltage 3.0V VIN 5.5V 1.25 IDX / ISET Output Current to Current Set Ratio VHR Current Source Voltage Headroom Requirement (Note 10) V 200 IDX = 95% IDX (nom.) RSET = 8.32k (IDX nom. = 30mA) 360 IDX = 95% IDX (nom.) RSET = 12.5k (IDX nom. = 20mA) 240 fSW Switching Frequency 525 (-30%) VIH Logic Input High Input Pins: EN, PWM 3.0V VIN 5.5V VIL Logic Input Low Input Pins: EN, PWM 3.0V VIN 5.5V 3 750 mV 975 (+30%) kHz 1.0 VIN V 0 0.4 www.national.com LM27951 Absolute Maximum Ratings (Notes 1, 2) LM27951 Electrical Characteristics (Notes 2, 7) (Continued) Limits in standard typeface are for TA = 25C, and limits in boldface type apply over the full operating junction temperature range (-40C to +85 C). Unless otherwise noted, specifications apply to the LM27951 Typical Application Circuit (pg.1) with VIN = 3.6V, V(EN) = 1.8V, V(PWM) = 1.8V, 4 LEDs, VDX = 3.6V, CIN = COUT = 3.3F, C1 = C2 = 1F, RSET = 12.5k (Note 8) Symbol IIH Parameter Logic Input High Current Conditions Min Typ Max Units Input Pin: PWM V(PWM) = 1.8V 10 nA Input Pin: EN V(EN) = 1.8V (Note 11) 12 A Input Pins: EN, PWM V(EN, PWM) = 0V 10 nA 3.3 IIL Logic Input Low Current ROUT Charge Pump Output Resistance (Note 12) VGDX 1x to 3/2x Gain Transition Voltage Threshold on VDX (VOUT - VDX) Falling 500 mV tON Startup Time IDX = 90% steady state 330 s Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 2: All voltages are with respect to the potential at the GND pin. Note 3: Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ=150C (typ.) and disengages at TJ = 140C (typ.). Note 4: The Human-body model is a 100 pF capacitor discharged through a 1.5k resistor into each pin. Note 5: In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operation junction temperature (TJ-MAX-OP = 115oC), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the part/package in the application (JA), as given by the following equation: TA-MAX = TJ-MAX-OP - (JA x PD-MAX). Note 6: Junction-to-ambient thermal resistance (JA) is taken from a thermal modeling result, performed under the conditions and guidelines set forth in the JEDEC standard JESD51-7. The test board is a 4 layer FR-4 board measuring 102mm x 76mm x 1.6mm with a 2 x 1 array of thermal vias. The ground plane on the board is 50mm x 50mm. Thickness of copper layers are 36m/18m /18m/36m (1.5oz/1oz/1oz/1.5oz). Ambient temperature in simulation is 22C, still air. Power dissipation is 1W. The value of JA of the LM27951 in LLP-14 could fall in a range as wide as 45oC/W to 150oC/W (if not wider), depending on PWB material, layout, and environmental conditions. In applications where high maximum power dissipation exists (high VIN, high IOUT), special care must be paid to thermal dissipation issues. For more information on these topics, please refer to Application Note 1187: Leadless Leadframe Package (LLP) and the Power Efficiency and Power Dissipation section of this datasheet.. Note 7: Min and Max limits are guaranteed by design, test, or statistical analysis. Typical numbers are not guaranteed, but do represent the most likely norm. Note 8: CIN, COUT, C1, C2: Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) used in setting electrical characteristics Note 9: LED Current Matching is based on two calculations: [(IMAX - IAVG) / IAVG] and [(IAVG - IMIN) / IAVG]. IMAX and IMIN are the highest and lowest respective Dx currents, and IAVG is the average Dx current of all four current sources. The largest number of the two calculations (worst case) is considered the matching figure for the part. The typical specification provided is the most likely norm of the matching figure for all parts. Note 10: Headroom Voltage (VHR) = VOUT - VDX. If headroom voltage requirement is not met, LED current regulation will be compromised. Note 11: EN Logic Input High Current (IIH) is due to a 150k (typ.) pull-down resistor connected internally between the EN and GND pins. Note 12: The open loop output resistance (ROUT) models all voltage losses in the charge pump. ROUT can be used to estimate the voltage at the charge pump output VOUT and the maximum current capability of the device under low VIN and high IOUT conditions, beyond what is specified in the electrical specifications table: VOUT = (G x VIN) - (ROUT x IOUT). In the equation, G is the charge pump gain mode, and IOUT is the total output current (sum of all active Dx current sources and all current drawn from VOUT). Note 13: Turn-on time is measured from when the EN signal is pulled high until the output voltage on VOUT crosses 90% of its final value. www.national.com 4 LM27951 Block Diagram 20171703 5 www.national.com LM27951 Typical Performance Characteristics Unless otherwise specified: TA = 25C, 4 LEDs, VDX = 3.6V, VIN = 3.6V, VEN = VIN, VPWM = VIN, C1 = C2 = 1F, CIN = COUT = 3.3F. Capacitors are low-ESR multi-layer ceramic capacitors (MLCC's). LED Current Regulation vs. Input Voltage Average LED Current Regulation vs. Input Voltage 20171704 20171706 Converter Efficiency vs. Input Voltage LED Current vs. RSET 20171708 20171709 Input and Output Voltage Ripple Startup Response 20171712 20171713 VIN = 3.6V, Load = 15mA/LED, 4 LEDs VIN = 3.6V, Load = 20mA/LED, 4 LEDs CH1 (TOP): VIN; Scale: 20mV/Div, AC Coupled CH1 (TOP): VEN; Scale: 1V/Div CH2 (BOTTOM): VOUT; Scale: 20mV/Div, AC Coupled Time scale: 400ns/Div Time scale: 100s/Div www.national.com CH2 (BOTTOM): VOUT; Scale: 1V/Div 6 CIRCUIT DESCRIPTION The LM27951 is an adaptive 1.5x/1x CMOS charge pump, optimized for driving white LEDs used in small-format display backlighting. It provides four constant current outputs capable of sourcing up to 30mA through each LED. The well-matched current sources ensure the current through all the LEDs are virtually identical, providing a uniform brightness across the entire display. Each current source is internally connected to the charge pump output, VOUT. LED drive current is programmed by connecting a resistor, RSET, to the current set pin, ISET. LED brightness is adjusted by applying a Pulse Width Modulated (PWM) signal to the dedicated PWM input pin. ADJUSTING LED BRIGHTNESS (PWM control) Perceived LED brightness can be adjusted using a PWM control signal on the LM27951 PWM logic input pin, turning the current sources ON and OFF at a rate faster than perceptible by the human eye. When this is done, the total brightness perceived is proportional to the duty cycle (D) of the PWM signal (D = the percentage of time that the LED is on in every PWM cycle). A simple example: if the LEDs are driven at 15mA each with a PWM signal that has a 50% duty cycle, perceived LED brightness will be about half as bright as compared to when the LEDs are driven continuously with 15mA. CHARGE PUMP The input to the 1.5x/1x charge pump is connected to the VIN pin, and the loosely regulated output of the charge pump is connected to the VOUT pin. The recommended input voltage range of the LM27951 is 3.0V to 5.5V. The device's looselyregulated charge pump has both open loop and closed loop modes of operation. When the device is in open loop, the voltage at VOUT is equal to the gain times the voltage at the input. When the device is in closed loop, the voltage at VOUT is loosely regulated to 4.5V (typ.). The charge pump gain transitions are actively selected to maintain regulation based on LED forward voltage and load requirements. This allows the charge pump to stay in the most efficient gain (1x) over as much of the input voltage range as possible, reducing the power consumed from the battery. The minimum recommended PWM frequency is 100Hz. Frequencies below this may be visible as flicker or blinking. The maximum recommended PWM frequency is 1kHz. Frequencies above this may cause interference with internal current driver circuitry and/or noise in the audible range. Due to the regulation control loop, the maximum frequency and minimum duty cycle applied to the PWM pin should be chosen such that the minimum ON time is no less than 30s in duration. If a PWM signal is applied to the EN pin instead, the maximum frequency and minimum duty cycle should be chosen to accommodate both the LM27951 startup time (330s typ.) and the 30s control loop delay. The preferred method to adjust brightness is to keep the master EN voltage ON continuously and apply a PWM signal to the dedicated PWM input pin. The benefit of this type of connection can be best understood with a contrary example. When a PWM signal is connected to the master enable (EN) pin, the charge pump repeatedly turns on and off. Every time the charge pump turns on, there is an inrush of current as the capacitors, both internal and external, are recharged. This inrush current results in a current spike and a voltage dip at the input of the part. By applying the PWM signal to PWM logic input pin, the charge pump remains active, resulting in much lower input noise. In cases where a PWM signal must be connected to the EN pin, measures can be taken to reduce the magnitude of the charge-pump turn-on transient response. More input capacitance, series resistors and/or ferrite beads may provide benefits. If the current spikes and voltage dips can be tolerated, connecting the PWM signal to the EN pin does provide a benefit of lower supply current consumption. When the PWM signal to the EN pin is low, the LM27951 will be shutdown and input current will only be a few micro-amps. This results in a lower time-averaged input current than the prior suggestion, where EN is kept on continuously. SOFT START The LM27951 contains internal soft-start circuitry to limit input inrush currents when the part is enabled. Soft start is implemented internally with a controlled turn-on of the internal voltage reference. Due to the soft-start circuitry, startup time of the LM27951 is approximately 330s (typ.). ENABLE AND PWM PINS The LM27951 has 2 logic control pins. Both pins are activehigh logic (HIGH = ON). There is an internal pull-down resistor (150k typ.) connected between the enable pin (EN) and GND. There is no pull-up or pull-down connected to the Pulse Width Modulated (PWM) pin. The EN pin is the master enable pin for the part. When the voltage on this pin is low ( < 0.4V), the part is in shutdown mode. In this mode, all internal circuitry is OFF and the part consumes very little supply current ( < 1A typ.). When the voltage on the EN pin is high ( > 1.0V), the part will activate the charge pump and regulate the output voltage to its nominal value. The PWM pin serves as a dedicated logic input for LED brightness control. When the voltage on this pin is low ( < 0.4V), the current sources will be turned off and no current will flow through the LEDs. When the voltage on this pin is high ( > 1.0V), the currents sources will turn on and regulate to the current level set by the resistor connected to the ISET pin. MAXIMUM OUTPUT CURRENT, MAXIMUM LED VOLTAGE, MINIMUM INPUT VOLTAGE The LM27951 can drive 4 LEDs at 30mA each from an input voltage as low as 3.0V, so long as the LEDs have a forward voltage of 3.6V or less (room temperature). The statement above is a simple example of the LED drive capabilities of the LM27951. The statement contains key application parameters required to validate an LED-drive SETTING LED CURRENTS The current through the four LEDs connected to D1-4 can be set to a desired level simply by connecting an appropriately sized resistor (RSET) between the ISET pin of the LM27951 and GND. The LED currents are proportional to the current 7 www.national.com LM27951 that flows out of the ISET pin and are a factor of 200 times greater than the ISET current. The feedback loop of an internal amplifier sets the voltage of the ISET pin to 1.25V (typ.). The statements above are simplified in the equations below: IDx = 200 x(VSET / RSET) RSET = 200 x (1.25V / IDx) Application Information LM27951 Application Information PARALLEL DX OUTPUTS FOR INCREASED CURRENT DRIVE Outputs D1-4 may be connected together to drive a one or two LEDs at higher currents. In a one LED configuration, all four parallel current sources of equal value are connected together to drive a single LED. The LED current programmed should be chosen such that the current provided from each of the outputs is programmed to 25% of the total desired LED current. For example, if 60mA is the desired drive current for the single LED, RSET should be selected such that the current out of each current source is 15mA. Similarly, if two LEDs are to be driven by pairing up the D1-4 outputs (i.e D1-2, D3-4), RSET should be selected such that the current out of each current source output is 50% of the desired LED current. (Continued) design using the LM27951: LED current (ILED), number of active LEDs (N), LED forward voltage (VLED), and minimum input voltage (VIN-MIN). The equation below can be used to estimate the total output current capability of the LM27951: ILED_MAX = ((1.5 x VIN) - VLED) / ((N x ROUT) + kHR) (eq. 1) ILED_MAX = ((1.5 x VIN ) - VLED) / ((N x 3.3) + 12mV/mA) ROUT - Output resistance. This parameter models the internal losses of the charge pump that result in voltage droop at the pump output VOUT. Since the magnitude of the voltage droop is proportional to the total output current of the charge pump, the loss parameter is modeled as a resistance. The output resistance of the LM27951 is typically 3.3 (VIN = 3.0V, TA = 25C). In equation form: (eq. 2) VVOUT = 1.5 x VIN - N x ILED x ROUT kHR - Headroom constant. This parameter models the minimum voltage required across the current sources for proper regulation. This minimum voltage is proportional to the programmed LED current, so the constant has units of mV/mA. The typical kHR of the LM27951 is 12mV/mA. In equation form: (eq. 3) (VVOUT - VLED) > kHR x ILED The "ILED-MAX" equation (eq. 1) is obtained from combining the ROUT equation (eq. 2) with the kHR equation (eq. 3) and solving for ILED. Maximum LED current is highly dependent on minimum input voltage and LED forward voltage. Output current capability can be increased by raising the minimum input voltage of the application, or by selecting LEDs with a lower forward voltage. Excessive power dissipation may also limit output current capability of an application. Connecting the outputs in parallel does not affect the internal operation of the LM27951 and has no impact on the Electrical Characteristics and limits previously presented. The available diode output current, maximum diode voltage, and all other specifications provided in the Electrical Characteristics table apply to this parallel output configuration, just as they do to the standard 4-LED application circuit. POWER EFFICIENCY Efficiency of LED drivers is commonly taken to be the ratio of power consumed by the LEDs (PLED) to the power drawn at the input of the part (PIN). With a 1.5x/1x charge pump, the input current is equal to the charge pump gain times the output current (total LED current). For a simple approximation, the current consumed by internal circuitry can be neglected and the efficiency of the LM27951 can be predicted as follows: PLED = N x VLED x ILED PIN = VIN x IIN CAPACITOR SELECTION The LM27951 requires 4 external capacitors for proper operation. Surface-mount multi-layer ceramic capacitors are recommended. These capacitors are small, inexpensive and have very low equivalent series resistance (ESR < 20m typ.). Tantalum capacitors, OS-CON capacitors, and aluminum electrolytic capacitors are not recommended for use with the LM27951 due to their high ESR, as compared to ceramic capacitors. For most applications, ceramic capacitors with X7R or X5R temperature characteristic are preferred for use with the LM27951. These capacitors have tight capacitance tolerance (as good as 10%) and hold their value over temperature (X7R: 15% over -55C to 125C; X5R: 15% over -55C to 85C). Capacitors with Y5V or Z5U temperature characteristic are generally not recommended for use with the LM27951. Capacitors with these temperature characteristics typically have wide capacitance tolerance (+80%, -20%) and vary significantly over temperature (Y5V: +22%, -82% over -30C to +85C range; Z5U: +22%, -56% over +10C to +85C range). Under some conditions, a nominal 1F Y5V or Z5U capacitor could have a capacitance of only 0.1F. Such detrimental deviation is likely to cause Y5V and Z5U capacitors to fail to meet the minimum capacitance requirements of the LM27951. The voltage rating of the output capacitor should be 10V or more. All other capacitors should have a voltage rating at or above the maximum input voltage of the application. www.national.com PIN = VIN x (Gain x N x ILED + IQ) E = (PLED / PIN) Neglecting IQ will result in a slightly higher efficiency prediction, but this impact will be no more than a few percentage points when several LEDs are driven at full power. It is also worth noting that efficiency as defined here is in part dependent on LED voltage. Variation in LED voltage does not affect power consumed by the circuit and typically does not relate to the brightness of the LED. For an advanced analysis, it is recommended that power consumed by the circuit (VIN x IIN) be evaluated rather than power efficiency. THERMAL PROTECTION Internal thermal protection circuitry disables the LM27951 when the junction temperature exceeds 150C (typ.). This feature protects the device from being damaged by high die temperatures that might otherwise result from excessive power dissipation. The device will recover and operate normally when the junction temperature falls below 140C (typ.). It is important that the board layout provide good thermal conduction to keep the junction temperature within the specified operating ratings. POWER DISSIPATION The power dissipation (PDISSIPATION) and junction temperature (TJ) can be approximated with the equations below. PIN is the power generated by the 1.5x/1x charge pump, PLED is the power consumed by the LEDs, TAis the ambient temperature, and JA is the junction-to-ambient thermal resis- 8 PCB Layout Considerations (Continued) The LLP is a leadframe based Chip Scale Package (CSP) with very good thermal properties. This package has an exposed DAP (die attach pad) at the center of the package measuring 3.0mm x 1.6mm. The main advantage of this exposed DAP is to offer lower thermal resistance when it is soldered to the thermal land on the PCB. For PCB layout, National highly recommends a 1:1 ratio between the package and the PCB thermal land. To further enhance thermal conductivity, the PCB thermal land may include vias to a ground plane. For more detailed instructions on mounting LLP packages, please refer to National Semiconductor Application Note AN-1187. tance for the LLP-14 package. VIN is the input voltage to the LM27951, VLED is the nominal LED forward voltage, and ILED is the programmed LED current. PDISSIPATION = PIN - PLED = [Gain x VIN x (4 x ILED)] - (VLED x 4 x ILED) TJ = TA + (PDISSIPATION x JA) The junction temperature rating takes precedence over the ambient temperature rating. The LM27951 may be operated outside the ambient temperature rating, so long as the junction temperature of the device does not exceed the maximum operating rating of 115C. The maximum ambient temperature rating must be derated in applications where high power dissipation and/or poor thermal resistance causes the junction temperature to exceed 115C. 9 www.national.com LM27951 Application Information LM27951 White LED Adaptive 1.5X/1X Switched Capacitor Current Driver Physical Dimensions inches (millimeters) unless otherwise noted 14-Pin LLP NS Package Number SDA14A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated