EPM7128BFI100-7N - Altera Corporation

Altera Corporation 1

MAX 7000B

Programmable Logic

Device

September 2005, ver. 3.5 Data Sheet

DS-MAX7000B-3.5

Features... ■High-performance 2.5-V CMOS EEPROM-based programmable logic

devices (PLDs) built on second-generation Multiple Array MatriX

(MAX®) architecture (see Table 1)

– Pin-compatible with the popular 5.0-V MAX 7000S and 3.3-V

MAX 7000A device families

– High-density PLDs ranging from 600 to 10,000 usable gates

– 3.5-ns pin-to-pin logic delays with counter frequencies in excess

of 303.0 MHz

■Advanced 2.5-V in-system programmability (ISP)

– Programs through the built-in IEEE Std. 1149.1 Joint Test Action

Group (JTAG) interface with advanced pin-locking capability

– Enhanced ISP algorithm for faster programming

– ISP_Done bit to ensure complete programming

– Pull-up resistor on I/O pins during in-system programming

– ISP circuitry compliant with IEEE Std. 1532

fFor information on in-system programmable 5.0-V MAX 7000S or 3.3-V

MAX 7000A devices, see the MAX 7000 Programmable Logic Device Family

Data Sheet or the MAX 7000A Programmable Logic Device Family Data Sheet.

Table 1. MAX 7000B Device Features

Feature EPM7032B EPM7064B EPM7128B EPM7256B EPM7512B

Usable gates 600 1,250 2,500 5,000 10,000

Macrocells 32 64 128 256 512

Logic array blocks 2 4 8 16 32

Maximum user I/O

pins 36 68 100 164 212

tPD (ns) 3.5 3.5 4.0 5.0 5.5

tSU (ns) 2.1 2.1 2.5 3.3 3.6

tFSU (ns) 1.0 1.0 1.0 1.0 1.0

tCO1 (ns) 2.4 2.4 2.8 3.3 3.7

fCNT (MHz) 303.0 303.0 243.9 188.7 163.9

2Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

...and More

Features

■System-level features

–MultiVolt

TM I/O interface enabling device core to run at 2.5 V,

while I/O pins are compatible with 3.3-V, 2.5-V, and 1.8-V logic

levels

– Programmable power-saving mode for 50% or greater power

reduction in each macrocell

– Fast input setup times provided by a dedicated path from I/O

pin to macrocell registers

– Support for advanced I/O standards, including SSTL-2 and

SSTL-3, and GTL+

– Bus-hold option on I/O pins

–PCI compatible

– Bus-friendly architecture including programmable slew-rate

control

– Open-drain output option

– Programmable security bit for protection of proprietary designs

– Built-in boundary-scan test circuitry compliant with

IEEE Std. 1149.1

– Supports hot-socketing operation

– Programmable ground pins

■Advanced architecture features

– Programmable interconnect array (PIA) continuous routing

structure for fast, predictable performance

– Configurable expander product-term distribution, allowing up

to 32 product terms per macrocell

– Programmable macrocell registers with individual clear, preset,

clock, and clock enable controls

– Two global clock signals with optional inversion

– Programmable power-up states for macrocell registers

– 6 to 10 pin- or logic-driven output enable signals

■Advanced package options

– Pin counts ranging from 44 to 256 in a variety of thin quad flat

pack (TQFP), plastic quad flat pack (PQFP), ball-grid array

(BGA), space-saving FineLine BGATM, 0.8-mm Ultra

FineLine BGA, and plastic J-lead chip carrier (PLCC) packages

– Pin-compatibility with other MAX 7000B devices in the same

package

■Advanced software support

– Software design support and automatic place-and-route

provided by Altera’s MAX+PLUS® II development system for

Windows-based PCs and Sun SPARCstation, and HP 9000

Series 700/800 workstations

Altera Corporation 3

MAX 7000B Programmable Logic Device Data Sheet

– Additional design entry and simulation support provided by

EDIF 2 0 0 and 3 0 0 netlist files, library of parameterized

modules (LPMs), Verilog HDL, VHDL, and other interfaces to

popular EDA tools from manufacturers such as Cadence,

Exemplar Logic, Mentor Graphics, OrCAD, Synopsys,

Synplicity, and VeriBest

– Programming support with Altera’s Master Programming Unit

(MPU), MasterBlasterTM serial/universal serial bus (USB)

communications cable, and ByteBlasterMVTM parallel port

download cable, as well as programming hardware from third-

party manufacturers and any JamTM STAPL File (.jam), Jam Byte-

Code File (.jbc), or Serial Vector Format File (.svf)-capable in-

circuit tester

General

Description

MAX 7000B devices are high-density, high-performance devices based on

Altera’s second-generation MAX architecture. Fabricated with advanced

CMOS technology, the EEPROM-based MAX 7000B devices operate with

a 2.5-V supply voltage and provide 600 to 10,000 usable gates, ISP,

pin-to-pin delays as fast as 3.5 ns, and counter speeds up to 303.0 MHz.

See Table 2.

Notes:

(1) Contact Altera Marketing for up-to-date information on available device speed

grades.

The MAX 7000B architecture supports 100% TTL emulation and high-

density integration of SSI, MSI, and LSI logic functions. It easily integrates

multiple devices ranging from PALs, GALs, and 22V10s to MACH and

pLSI devices. MAX 7000B devices are available in a wide range of

packages, including PLCC, BGA, FineLine BGA, 0.8-mm Ultra FineLine

BGA, PQFP, TQFP, and TQFP packages. See Table 3.

Table 2. MAX 7000B Speed Grades Note (1)

Device Speed Grade

-3 -4 -5 -7 -10

EPM7032B vvv

EPM7064B vvv

EPM7128B vvv

EPM7256B vvv

EPM7512B vvv

4Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Notes:

(1) When the IEEE Std. 1149.1 (JTAG) interface is used for in-system programming or boundary-scan testing, four I/O

pins become JTAG pins.

(2) Contact Altera for up-to-date information on available device package options.

(3) All 0.8-mm Ultra FineLine BGA packages are footprint-compatible via the SameFrameTM pin-out feature. Therefore,

designers can design a board to support a variety of devices, providing a flexible migration path across densities

and pin counts. Device migration is fully supported by Altera development tools. See “SameFrame Pin-Outs” on

page 14 for more details.

(4) All FineLine BGA packages are footprint-compatible via the SameFrame pin-out feature. Therefore, designers can

design a board to support a variety of devices, providing a flexible migration path across densities and pin counts.

Device migration is fully supported by Altera development tools. See “SameFrame Pin-Outs” on page 14 for more

details.

MAX 7000B devices use CMOS EEPROM cells to implement logic

functions. The user-configurable MAX 7000B architecture accommodates

a variety of independent combinatorial and sequential logic functions.

The devices can be reprogrammed for quick and efficient iterations

during design development and debug cycles, and can be programmed

and erased up to 100 times.

MAX 7000B devices contain 32 to 512 macrocells that are combined into

groups of 16 macrocells, called logic array blocks (LABs). Each macrocell

has a programmable-AND/fixed-OR array and a configurable register with

independently programmable clock, clock enable, clear, and preset

functions. To build complex logic functions, each macrocell can be

supplemented with both shareable expander product terms and high-

speed parallel expander product terms to provide up to 32 product terms

per macrocell.

Table 3. MAX 7000B Maximum User I/O Pins Note (1)

Device 44-Pin

PLCC

44-Pin

TQFP

48-Pin

TQFP

(2)

49-Pin

0.8-mm

Ultra

FineLine

BGA (3)

100-

TQFP

100-Pin

FineLine

BGA (4)

144-

TQFP

169-Pin

0.8-mm

Ultra

FineLine

BGA (3)

208-

PQFP

256-

BGA

256-Pin

FineLine

BGA (4)

EPM7032B 36 36 36 36

EPM7064B 36 36 40 41 68 68

EPM7128B 41 84 84 100 100 100

EPM7256B 84 120 141 164 164

EPM7512B 120 141 176 212 212

Altera Corporation 5

MAX 7000B Programmable Logic Device Data Sheet

MAX 7000B devices provide programmable speed/power optimization.

Speed-critical portions of a design can run at high speed/full power,

while the remaining portions run at reduced speed/low power. This

speed/power optimization feature enables the designer to configure one

or more macrocells to operate up to 50% lower power while adding only

a nominal timing delay. MAX 7000B devices also provide an option that

reduces the slew rate of the output buffers, minimizing noise transients

when non-speed-critical signals are switching. The output drivers of all

MAX 7000B devices can be set for 3.3 V, 2.5 V, or 1.8 V and all input pins

are 3.3-V, 2.5-V, and 1.8-V tolerant, allowing MAX 7000B devices to be

used in mixed-voltage systems.

MAX 7000B devices are supported by Altera development systems, which

are integrated packages that offer schematic, text—including VHDL,

Verilog HDL, and the Altera Hardware Description Language (AHDL)—

and waveform design entry, compilation and logic synthesis, simulation

and timing analysis, and device programming. Altera software provides

EDIF 2 0 0 and 3 0 0, LPM, VHDL, Verilog HDL, and other interfaces for

additional design entry and simulation support from other industry-

standard PC- and UNIX-workstation-based EDA tools. Altera software

runs on Windows-based PCs, as well as Sun SPARCstation, and HP 9000

Series 700/800 workstations.

fFor more information on development tools, see the MAX+PLUS II

Programmable Logic Development System & Software Data Sheet and the

Quartus Programmable Logic Development System & Software Data Sheet.

Functional

Description

The MAX 7000B architecture includes the following elements:

■LABs

■Macrocells

■Expander product terms (shareable and parallel)

■PIA

■I/O control blocks

The MAX 7000B architecture includes four dedicated inputs that can be

used as general-purpose inputs or as high-speed, global control signals

(clock, clear, and two output enable signals) for each macrocell and I/O

pin. Figure 1 shows the architecture of MAX 7000B devices.

6Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Figure 1. MAX 7000B Device Block Diagram

Note:

(1) EPM7032B, EPM7064B, EPM7128B, and EPM7256B devices have six output enables. EPM7512B devices have ten

output enables.

Logic Array Blocks

The MAX 7000B device architecture is based on the linking of

high-performance LABs. LABs consist of 16 macrocell arrays, as shown in

Figure 1. Multiple LABs are linked together via the PIA, a global bus that

is fed by all dedicated input pins, I/O pins, and macrocells.

Each LAB is fed by the following signals:

■36 signals from the PIA that are used for general logic inputs

■Global controls that are used for secondary register functions

■Direct input paths from I/O pins to the registers that are used for fast

setup times

6 or 10

INPUT/GCLRn

6 or 10 Output Enables

(1)

6 or 10 Output Enables

(1)

36 36

I/O

Control

Block

LAB C LAB D

I/O

Control

Block

6 or 10

36 36

I/O

Control

Block

LAB A

Macrocells

1 to 16

LAB B

I/O

Control

Block

6 or 10

PIA

INPUT/GCLK1

INPUT/OE2/GCLK2

INPUT/OE1

2 to 16 I/O

2 to 16

Macrocells

17 to 32

Macrocells

33 to 48 Macrocells

49 to 64

Altera Corporation 7

MAX 7000B Programmable Logic Device Data Sheet

Macrocells

The MAX 7000B macrocell can be individually configured for either

sequential or combinatorial logic operation. The macrocell consists of

three functional blocks: the logic array, the product-term select matrix,

and the programmable register. Figure 2 shows the MAX 7000B

macrocell.

Figure 2. MAX 7000B Macrocell

Combinatorial logic is implemented in the logic array, which provides

five product terms per macrocell. The product-term select matrix allocates

these product terms for use as either primary logic inputs (to the OR and

XOR gates) to implement combinatorial functions, or as secondary inputs

to the macrocell’s register preset, clock, and clock enable control

functions.

Two kinds of expander product terms (“expanders”) are available to

supplement macrocell logic resources:

■Shareable expanders, which are inverted product terms that are fed

back into the logic array

■Parallel expanders, which are product terms borrowed from adjacent

macrocells

Product-

Term

Select

Matrix

36 Signals

from PIA 16 Expander

Product Terms

LAB Local Array

Parallel Logic

Expanders

(from other

macrocells)

Shared Logic

Expanders

Clear

Select

Global

Clear Global

Clocks

Clock/

Enable

Select

PRN

CLRN

D/T Q

ENA

Bypass To I/O

Control

Block

From

I/O pin

To PIA

Programmable

Fast Input

Select

VCC

8Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

The Altera development system automatically optimizes product-term

allocation according to the logic requirements of the design.

For registered functions, each macrocell flipflop can be individually

programmed to implement D, T, JK, or SR operation with programmable

clock control. The flipflop can be bypassed for combinatorial operation.

During design entry, the designer specifies the desired flipflop type; the

MAX+PLUS II software then selects the most efficient flipflop operation

for each registered function to optimize resource utilization.

Each programmable register can be clocked in three different modes:

■Global clock signal. This mode achieves the fastest clock-to-output

performance.

■Global clock signal enabled by an active-high clock enable. A clock

enable is generated by a product term. This mode provides an enable

on each flipflop while still achieving the fast clock-to-output

performance of the global clock.

■Array clock implemented with a product term. In this mode, the

flipflop can be clocked by signals from buried macrocells or I/O pins.

Two global clock signals are available in MAX 7000B devices. As shown

in Figure 1, these global clock signals can be the true or the complement of

either of the global clock pins, GCLK1 or GCLK2.

Each register also supports asynchronous preset and clear functions. As

shown in Figure 2, the product-term select matrix allocates product terms

to control these operations. Although the product-term-driven preset and

clear from the register are active high, active-low control can be obtained

by inverting the signal within the logic array. In addition, each register

clear function can be individually driven by the active-low dedicated

global clear pin (GCLRn). Upon power-up, each register in a MAX 7000B

device may be set to either a high or low state. This power-up state is

specified at design entry.

All MAX 7000B I/O pins have a fast input path to a macrocell register.

This dedicated path allows a signal to bypass the PIA and combinatorial

logic and be clocked to an input D flipflop with an extremely fast input

setup time. The input path from the I/O pin to the register has a

programmable delay element that can be selected to either guarantee zero

hold time or to get the fastest possible set-up time (as fast as 1.0 ns).

Altera Corporation 9

MAX 7000B Programmable Logic Device Data Sheet

Expander Product Terms

Although most logic functions can be implemented with the five product

terms available in each macrocell, more complex logic functions require

additional product terms. Another macrocell can be used to supply the

required logic resources. However, the MAX 7000B architecture also

offers both shareable and parallel expander product terms (“expanders”)

that provide additional product terms directly to any macrocell in the

same LAB. These expanders help ensure that logic is synthesized with the

fewest possible logic resources to obtain the fastest possible speed.

Shareable Expanders

Each LAB has 16 shareable expanders that can be viewed as a pool of

uncommitted single product terms (one from each macrocell) with

inverted outputs that feed back into the logic array. Each shareable

expander can be used and shared by any or all macrocells in the LAB to

build complex logic functions. A small delay (tSEXP) is incurred when

shareable expanders are used. Figure 3 shows how shareable expanders

can feed multiple macrocells.

Figure 3. MAX 7000B Shareable Expanders

Shareable expanders can be shared by any or all macrocells in an LAB.

Macrocell

Product-Term

Logic

Product-Term Select Matrix

Macrocell

Product-Term

Logic

36 Signals

from PIA 16 Shared

Expanders

10 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Parallel Expanders

Parallel expanders are unused product terms that can be allocated to a

neighboring macrocell to implement fast, complex logic functions.

Parallel expanders allow up to 20 product terms to directly feed the

macrocell OR logic, with five product terms provided by the macrocell and

15 parallel expanders provided by neighboring macrocells in the LAB.

The Altera Compiler can automatically allocate up to three sets of up to

five parallel expanders to the macrocells that require additional product

terms. Each set of five parallel expanders incurs a small, incremental

timing delay (tPEXP). For example, if a macrocell requires 14 product

terms, the Compiler uses the five dedicated product terms within the

macrocell and allocates two sets of parallel expanders; the first set

includes five product terms and the second set includes four product

terms, increasing the total delay by 2 × tPEXP.

Two groups of eight macrocells within each LAB (e.g., macrocells 1

through 8, and 9 through 16) form two chains to lend or borrow parallel

expanders. A macrocell borrows parallel expanders from lower-

numbered macrocells. For example, macrocell 8 can borrow parallel

expanders from macrocell 7, from macrocells 7 and 6, or from macrocells

7, 6, and 5. Within each group of eight, the lowest-numbered macrocell

can only lend parallel expanders and the highest-numbered macrocell can

only borrow them. Figure 4 shows how parallel expanders can be

borrowed from a neighboring macrocell.

Altera Corporation 11

MAX 7000B Programmable Logic Device Data Sheet

Figure 4. MAX 7000B Parallel Expanders

Unused product terms in a macrocell can be allocated to a neighboring macrocell.

Programmable Interconnect Array

Logic is routed between LABs on the PIA. This global bus is a

programmable path that connects any signal source to any destination on

the device. All MAX 7000B dedicated inputs, I/O pins, and macrocell

outputs feed the PIA, which makes the signals available throughout the

entire device. Only the signals required by each LAB are actually routed

from the PIA into the LAB. Figure 5 shows how the PIA signals are routed

into the LAB. An EEPROM cell controls one input to a two-input AND gate,

which selects a PIA signal to drive into the LAB.

Preset

Clock

Clear

Product-

Term

Select

Matrix

Preset

Clock

Clear

Product-

Term

Select

Matrix

Macrocell

Product-

Term Logic

From

Macrocell

To Next

Macrocell

Product-

Term Logic

36 Signals

from PIA 16 Shared

Expanders

12 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Figure 5. MAX 7000B PIA Routing

While the routing delays of channel-based routing schemes in masked or

field-programmable gate arrays (FPGAs) are cumulative, variable, and

path-dependent, the MAX 7000B PIA has a predictable delay. The PIA

makes a design’s timing performance easy to predict.

I/O Control Blocks

The I/O control block allows each I/O pin to be individually configured

for input, output, or bidirectional operation. All I/O pins have a tri-state

buffer that is individually controlled by one of the global output enable

signals or directly connected to ground or VCC. Figure 6 shows the I/O

control block for MAX 7000B devices. The I/O control block has

six or ten global output enable signals that are driven by the true or

complement of two output enable signals, a subset of the I/O pins, or a

subset of the I/O macrocells.

To LAB

PIA Signals

Altera Corporation 13

MAX 7000B Programmable Logic Device Data Sheet

Figure 6. I/O Control Block of MAX 7000B Devices

Note:

(1) EPM7032B, EPM7064B, EPM7128B, and EPM7256B devices have six output enable signals. EPM7512B devices have

ten output enable signals.

When the tri-state buffer control is connected to ground, the output is

tri-stated (high impedance) and the I/O pin can be used as a dedicated

input. When the tri-state buffer control is connected to VCC, the output is

enabled.

The MAX 7000B architecture provides dual I/O feedback, in which

macrocell and pin feedbacks are independent. When an I/O pin is

configured as an input, the associated macrocell can be used for buried

logic.

from

Macrocell

Fast Input to

Macrocell

Slew-Rate Control

I/O Standards

to PIA

to Other I/O Pins

6 or 10 Global

Output Enable Signals (1)

PIA

VCC

Open-Drain Output

OE Select Multiplexer

GND

Programmable Delay

Bus Hold Programmable

Ground

Programmable

Pull-up

14 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

SameFrame

Pin-Outs

MAX 7000B devices support the SameFrame pin-out feature for

FineLine BGA and 0.8-mm Ultra FineLine BGA packages. The

SameFrame pin-out feature is the arrangement of balls on FineLine BGA

and 0.8-mm Ultra FineLine BGA packages such that the lower-ball-count

packages form a subset of the higher-ball-count packages. SameFrame

pin-outs provide the flexibility to migrate not only from device to device

within the same package, but also from one package to another. FineLine

BGA packages are compatible with other FineLine BGA packages, and

0.8-mm Ultra FineLine BGA packages are compatible with other 0.8-mm

Ultra FineLine BGA packages. A given printed circuit board (PCB) layout

can support multiple device density/package combinations. For example,

a single board layout can support a range of devices from an EPM7064B

device in a 100-pin FineLine BGA package to an EPM7512B device in a

256-pin FineLine BGA package.

The Altera software provides support to design PCBs with SameFrame

pin-out devices. Devices can be defined for present and future use. The

Altera software generates pin-outs describing how to layout a board to

take advantage of this migration (see Figure 7).

Figure 7. SameFrame Pin-Out Example

Designed for 256-Pin FineLine BGA Package

Printed Circuit Board

100-Pin FineLine BGA Package

(Reduced I/O Count or

Logic Requirements)

256-Pin FineLine BGA Package

(Increased I/O Count or

Logic Requirements)

100-Pin

FineLine

BGA

256-Pin

FineLine

BGA

Altera Corporation 15

MAX 7000B Programmable Logic Device Data Sheet

In-System

Programma-

bility (ISP)

MAX 7000B devices can be programmed in-system via an industry-

standard 4-pin IEEE Std. 1149.1 (JTAG) interface. ISP offers quick, efficient

iterations during design development and debugging cycles. The

MAX 7000B architecture internally generates the high programming

voltages required to program EEPROM cells, allowing in-system

programming with only a single 2.5-V power supply. During in-system

programming, the I/O pins are tri-stated and weakly pulled-up to

eliminate board conflicts. The pull-up value is nominally 50 k¾.

MAX 7000B devices have an enhanced ISP algorithm for faster

programming. These devices also offer an ISP_Done bit that provides safe

operation when in-system programming is interrupted. This ISP_Done

bit, which is the last bit programmed, prevents all I/O pins from driving

until the bit is programmed.

ISP simplifies the manufacturing flow by allowing devices to be mounted

on a PCB with standard pick-and-place equipment before they are

programmed. MAX 7000B devices can be programmed by downloading

the information via in-circuit testers, embedded processors, the Altera

MasterBlaster communications cable, and the ByteBlasterMV parallel port

download cable. Programming the devices after they are placed on the

board eliminates lead damage on high-pin-count packages (e.g., QFP

packages) due to device handling. MAX 7000B devices can be

reprogrammed after a system has already shipped to the field. For

example, product upgrades can be performed in the field via software or

modem.

In-system programming can be accomplished with either an adaptive or

constant algorithm. An adaptive algorithm reads information from the

unit and adapts subsequent programming steps to achieve the fastest

possible programming time for that unit. A constant algorithm uses a

pre-defined (non-adaptive) programming sequence that does not take

advantage of adaptive algorithm programming time improvements.

Some in-circuit testers cannot program using an adaptive algorithm.

Therefore, a constant algorithm must be used. MAX 7000B devices can be

programmed with either an adaptive or constant (non-adaptive)

algorithm.

The Jam Standard Test and Programming Language (STAPL), JEDEC

standard JESD-71, can be used to program MAX 7000B devices with

in-circuit testers, PCs, or embedded processors.

fFor more information on using the Jam language, see Application Note 88

(Using the Jam Language for ISP & ICR via an Embedded Processor) and

Application Note 122 (Using STAPL for ISP & ICR via an Embedded Processor).

The ISP circuitry in MAX 7000B devices is compliant with the IEEE

Std. 1532 specification. The IEEE Std. 1532 is a standard developed to

allow concurrent ISP between multiple PLD vendors.

16 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Programming Sequence

During in-system programming, instructions, addresses, and data are

shifted into the MAX 7000B device through the TDI input pin. Data is

shifted out through the TDO output pin and compared against the

expected data.

Programming a pattern into the device requires the following six ISP

stages. A stand-alone verification of a programmed pattern involves only

stages 1, 2, 5, and 6.

1. Enter ISP. The enter ISP stage ensures that the I/O pins transition

smoothly from user mode to ISP mode. The enter ISP stage requires

1ms.

2. Check ID. Before any program or verify process, the silicon ID is

checked. The time required to read this silicon ID is relatively small

compared to the overall programming time.

3. Bulk Erase. Erasing the device in-system involves shifting in the

instructions to erase the device and applying one erase pulse of

100 ms.

4. Program. Programming the device in-system involves shifting in the

address and data and then applying the programming pulse to

program the EEPROM cells. This process is repeated for each

EEPROM address.

5. Verify. Verifying an Altera device in-system involves shifting in

addresses, applying the read pulse to verify the EEPROM cells, and

shifting out the data for comparison. This process is repeated for

each EEPROM address.

6. Exit ISP. An exit ISP stage ensures that the I/O pins transition

smoothly from ISP mode to user mode. The exit ISP stage requires

1ms.

Programming Times

The time required to implement each of the six programming stages can

be broken into the following two elements:

■A pulse time to erase, program, or read the EEPROM cells.

■A shifting time based on the test clock (TCK) frequency and the

number of TCK cycles to shift instructions, address, and data into the

device.

Altera Corporation 17

MAX 7000B Programmable Logic Device Data Sheet

By combining the pulse and shift times for each of the programming

stages, the program or verify time can be derived as a function of the TCK

frequency, the number of devices, and specific target device(s). Because

different ISP-capable devices have a different number of EEPROM cells,

both the total fixed and total variable times are unique for a single device.

Programming a Single MAX 7000B Device

The time required to program a single MAX 7000B device in-system can

be calculated from the following formula:

where: tPROG = Programming time

tPPULSE = Sum of the fixed times to erase, program, and

verify the EEPROM cells

CyclePTCK = Number of TCK cycles to program a device

fTCK =TCK frequency

The ISP times for a stand-alone verification of a single MAX 7000B device

can be calculated from the following formula:

where: tVER =Verify time

tVPULSE = Sum of the fixed times to verify the EEPROM cells

CycleVTCK = Number of TCK cycles to verify a device

tPROG tPPULSE

CyclePTCK

fTCK

--------------------------------+=

tVER tVPULSE

CycleVTCK

fTCK

--------------------------------+=

18 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

The programming times described in Tables 4 through 6 are associated

with the worst-case method using the enhanced ISP algorithm.

Tables 5 and 6 show the in-system programming and stand alone

verification times for several common test clock frequencies.

Table 4. MAX 7000B tPULSE & CycleTCK Values

Device Programming Stand-Alone Verification

tPPULSE (s) CyclePTCK tVPULSE (s) CycleVTCK

EMP7032B 2.12 70,000 0.002 18,000

EMP7064B 2.12 120,000 0.002 35,000

EMP7128B 2.12 222,000 0.002 69,000

EMP7256B 2.12 466,000 0.002 151,000

EMP7512B 2.12 914,000 0.002 300,000

Table 5. MAX 7000B In-System Programming Times for Different Test Clock Frequencies

Device fTCK Units

10 MHz 5 MHz 2 MHz 1 MHz 500 kHz 200 kHz 100 kHz 50 kHz

EMP7032B 2.13 2.13 2.15 2.19 2.26 2.47 2.82 3.52 s

EMP7064B 2.13 2.14 2.18 2.24 2.36 2.72 3.32 4.52 s

EMP7128B 2.14 2.16 2.23 2.34 2.56 3.23 4.34 6.56 s

EMP7256B 2.17 2.21 2.35 2.58 3.05 4.45 6.78 11.44 s

EMP7512B 2.21 2.30 2.58 3.03 3.95 6.69 11.26 20.40 s

Table 1. MAX 7000B Stand-Alone Verification Times for Different Test Clock Frequencies

Device fTCK Units

10 MHz 5 MHz 2 MHz 1 MHz 500 kHz 200 kHz 100 kHz 50 kHz

EMP7032B 0.00 0.01 0.01 0.02 0.04 0.09 0.18 0.36 s

EMP7064B 0.01 0.01 0.02 0.04 0.07 0.18 0.35 0.70 s

EMP7128B 0.01 0.02 0.04 0.07 0.14 0.35 0.69 1.38 s

EMP7256B 0.02 0.03 0.08 0.15 0.30 0.76 1.51 3.02 s

EMP7512B 0.03 0.06 0.15 0.30 0.60 1.50 3.00 6.00 s

Altera Corporation 19

MAX 7000B Programmable Logic Device Data Sheet

Programming

with External

Hardware

MAX 7000B devices can be programmed on Windows-based PCs with an

Altera Logic Programmer card, the Master Programming Unit (MPU),

and the appropriate device adapter. The MPU performs continuity

checking to ensure adequate electrical contact between the adapter and

the device.

fFor more information, see the Altera Programming Hardware Data Sheet.

The Altera software can use text- or waveform-format test vectors created

with the Altera Text Editor or Waveform Editor to test the programmed

device. For added design verification, designers can perform functional

testing to compare the functional device behavior with the results of

simulation.

Data I/O, BP Microsystems, and other programming hardware

manufacturers provide programming support for Altera devices. For

more information, see Programming Hardware Manufacturers.

IEEE Std.

1149.1 (JTAG)

Boundary-Scan

Support

MAX 7000B devices include the JTAG boundary-scan test circuitry

defined by IEEE Std. 1149.1. Table 6 describes the JTAG instructions

supported by MAX 7000B devices. The pin-out tables starting on page 59

of this data sheet show the location of the JTAG control pins for each

device. If the JTAG interface is not required, the JTAG pins are available

as user I/O pins.

Table 6. MAX 7000B JTAG Instructions

JTAG Instruction Description

SAMPLE/PRELOAD Allows a snapshot of signals at the device pins to be captured and examined during

normal device operation, and permits an initial data pattern output at the device pins.

EXTEST Allows the external circuitry and board-level interconnections to be tested by forcing a

test pattern at the output pins and capturing test results at the input pins.

BYPASS Places the 1-bit bypass register between the TDI and TDO pins, which allows the

boundary-scan test data to pass synchronously through a selected device to adjacent

devices during normal operation.

CLAMP Allows the values in the boundary-scan register to determine pin states while placing the

1-bit bypass register between the TDI and TDO pins.

IDCODE Selects the IDCODE register and places it between the TDI and TDO pins, allowing the

IDCODE to be serially shifted out of TDO.

USERCODE Selects the 32-bit USERCODE register and places it between the TDI and TDO pins,

allowing the USERCODE value to be shifted out of TDO.

ISP Instructions These instructions are used when programming MAX 7000B devices via the JTAG ports

with the MasterBlaster or ByteBlasterMV download cable, or using a Jam File (.jam),

Jam Byte-Code File (.jbc), or Serial Vector Format File (.svf) via an embedded

processor or test equipment.

20 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

The instruction register length of MAX 7000B devices is ten bits. The

MAX 7000B USERCODE register length is 32 bits. Tables 7 and 8 show the

boundary-scan register length and device IDCODE information for

MAX 7000B devices.

Notes:

(1) The most significant bit (MSB) is on the left.

(2) The least significant bit (LSB) for all JTAG IDCODEs is 1.

fSee Application Note 39 (IEEE 1149.1 (JTAG) Boundary-Scan Testing in Altera

Devices) for more information on JTAG boundary-scan testing.

Figure 8 shows the timing information for the JTAG signals.

Table 7. MAX 7000B Boundary-Scan Register Length

Device Boundary-Scan Register Length

EPM7032B 96

EPM7064B 192

EPM7128B 288

EPM7256B 480

EPM7512B 624

Table 8. 32-Bit MAX 7000B Device IDCODE Note (1)

Device IDCODE (32 Bits)

Version

(4 Bits)

Part Number (16 Bits) Manufacturer’s

Identity (11 Bits)

1 (1 Bit)

(2)

EPM7032B 0010 0111 0000 0011 0010 00001101110 1

EPM7064B 0010 0111 0000 0110 0100 00001101110 1

EPM7128B 0010 0111 0001 0010 1000 00001101110 1

EPM7256B 0010 0111 0010 0101 0110 00001101110 1

EPM7512B 0010 0111 0101 0001 0010 00001101110 1

Altera Corporation 21

MAX 7000B Programmable Logic Device Data Sheet

Figure 8. MAX 7000B JTAG Waveforms

Table 9 shows the JTAG timing parameters and values for MAX 7000B

devices.

Note:

(1) Timing parameters in this table apply to all VCCIO levels.

Table 9. JTAG Timing Parameters & Values for MAX 7000B Devices

Note (1)

Symbol Parameter Min Max Unit

tJCP TCK clock period 100 ns

tJCH TCK clock high time 50 ns

tJCL TCK clock low time 50 ns

tJPSU JTAG port setup time 20 ns

tJPH JTAG port hold time 45 ns

tJPCO JTAG port clock to output 25 ns

tJPZX JTAG port high impedance to valid output 25 ns

tJPXZ JTAG port valid output to high impedance 25 ns

tJSSU Capture register setup time 20 ns

tJSH Capture register hold time 45 ns

tJSCO Update register clock to output 25 ns

tJSZX Update register high impedance to valid output 25 ns

tJSXZ Update register vali d output to high impedance 25 ns

TDO

TCK

tJPZX tJPCO

tJPH

tJPXZ

tJCP tJPSU

tJCL

tJCH

TDI

TMS

Signal

to Be

Captured

Signal

to Be

Driven

tJSZX

tJSSU tJSH

tJSCO tJSXZ

22 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Programmable

Speed/Power

Control

MAX 7000B devices offer a power-saving mode that supports low-power

operation across user-defined signal paths or the entire device. This

feature allows total power dissipation to be reduced by 50% or more,

because most logic applications require only a small fraction of all gates to

operate at maximum frequency.

The designer can program each individual macrocell in a MAX 7000B

device for either high-speed or low-power operation. As a result, speed-

critical paths in the design can run at high speed, while the remaining

paths can operate at reduced power. Macrocells that run at low power

incur a nominal timing delay adder (tLPA) for the tLAD, tLAC, tIC, tACL,

tCPPW, tEN, and tSEXP parameters.

Output

Configuration

MAX 7000B device outputs can be programmed to meet a variety of

system-level requirements.

MultiVolt I/O Interface

The MAX 7000B device architecture supports the MultiVolt I/O interface

feature, which allows MAX 7000B devices to connect to systems with

differing supply voltages. MAX 7000B devices in all packages can be set

for 3.3-V, 2.5-V, or 1.8-V pin operation. These devices have one set of VCC

pins for internal operation and input buffers (VCCINT), and another set for

I/O output drivers (VCCIO).

The VCCIO pins can be connected to either a 3.3-V, 2.5-V, or 1.8-V power

supply, depending on the output requirements. When the VCCIO pins are

connected to a 1.8-V power supply, the output levels are compatible with

1.8-V systems. When the VCCIO pins are connected to a 2.5-V power

supply, the output levels are compatible with 2.5-V systems. When the

VCCIO pins are connected to a 3.3-V power supply, the output high is at

3.3 V and is therefore compatible with 3.3-V or 5.0-V systems. Devices

operating with VCCIO levels of 2.5 V or 1.8 V incur a nominal timing delay

adder.

Table 10 describes the MAX 7000B MultiVolt I/O support.

Altera Corporation 23

MAX 7000B Programmable Logic Device Data Sheet

Open-Drain Output Option

MAX 7000B devices provide an optional open-drain (equivalent to

open-collector) output for each I/O pin. This open-drain output enables

the device to provide system-level control signals (e.g., interrupt and

write enable signals) that can be asserted by any of several devices. It can

also provide an additional wired-OR plane.

Programmable Ground Pins

Each unused I/O pin on MAX 7000B devices may be used as an additional

ground pin. This programmable ground feature does not require the use

of the associated macrocell; therefore, the buried macrocell is still

available for user logic.

Slew-Rate Control

The output buffer for each MAX 7000B I/O pin has an adjustable output

slew rate that can be configured for low-noise or high-speed performance.

A faster slew rate provides high-speed transitions for high-performance

systems. However, these fast transitions may introduce noise transients

into the system. A slow slew rate reduces system noise, but adds a

nominal delay of 4 to 5 ns. When the configuration cell is turned off, the

slew rate is set for low-noise performance. Each I/O pin has an individual

EEPROM bit that controls the slew rate, allowing designers to specify the

slew rate on a pin-by-pin basis. The slew rate control affects both the rising

and falling edges of the output signal.

Advanced I/O Standard Support

The MAX 7000B I/O pins support the following I/O standards: LVTTL,

LVCMOS, 1.8-V I/O, 2.5-V I/O, GTL+, SSTL-3 Class I and II, and SSTL-2

Class I and II.

Table 10. MAX 7000B MultiVolt I/O Support

VCCIO (V) Input Signal (V) Output Signal (V)

1.8 2.5 3.3 5.0 1.8 2.5 3.3 5.0

1.8 vvv v

2.5 vvv v

3.3 vvv vv

24 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

MAX 7000B devices contain two I/O banks. Both banks support all

standards. Each I/O bank has its own VCCIO pins. A single device can

support 1.8-V, 2.5-V, and 3.3-V interfaces; each bank can support a

different standard independently. Within a bank, any one of the

terminated standards can be supported.

Figure 9 shows the arrangement of the MAX 7000B I/O banks.

Figure 9. MAX 7000B I/O Banks for Various Advanced I/O Standards

Table 11 shows which macrocells have pins in each I/O bank.

Each MAX 7000B device has two VREF pins. Each can be set to a separate

VREF level. Any I/O pin that uses one of the voltage-referenced standards

(GTL+, SSTL-2, or SSTL-3) may use either of the two VREF pins. If these

pins are not required as VREF pins, they may be individually

programmed to function as user I/O pins.

Table 11. Macrocell Pins Contained in Each I/O Bank

Device Bank 1 Bank 2

EPM7032B 1-16 17-32

EPM7064B 1-32 33-64

EPM7128B 1-64 65-128

EPM7256B 1-128, 177-181 129-176, 182-256

EPM7512B 1-265 266-512

Individual

Power Bus

Programmable I/O Banks

Altera Corporation 25

MAX 7000B Programmable Logic Device Data Sheet

Programmable Pull-Up Resistor

Each MAX 7000B device I/O pin provides an optional programmable

pull-up resistor during user mode. When this feature is enabled for an I/O

pin, the pull-up resistor (typically 50 k¾) weakly holds the output to

VCCIO level.

Bus Hold

Each MAX 7000B device I/O pin provides an optional bus-hold feature.

When this feature is enabled for an I/O pin, the bus-hold circuitry weakly

holds the signal at its last driven state. By holding the last driven state of

the pin until the next input signals is present, the bus-hold feature can

eliminate the need to add external pull-up or pull-down resistors to hold

a signal level when the bus is tri-stated. The bus-hold circuitry also pulls

undriven pins away from the input threshold voltage where noise can

cause unintended high-frequency switching. This feature can be selected

individually for each I/O pin. The bus-hold output will drive no higher

than VCCIO to prevent overdriving signals. The propagation delays

through the input and output buffers in MAX 7000B devices are not

affected by whether the bus-hold feature is enabled or disabled.

The bus-hold circuitry weakly pulls the signal level to the last driven state

through a resistor with a nominal resistance (RBH) of approximately

8.5 k¾. Table 12 gives specific sustaining current that will be driven

through this resistor and overdrive current that will identify the next

driven input level. This information is provided for each VCCIO voltage

level.

The bus-hold circuitry is active only during user operation. At power-up,

the bus-hold circuit initializes its initial hold value as VCC approaches the

recommended operation conditions. When transitioning from ISP to User

Mode with bus hold enabled, the bus-hold circuit captures the value

present on the pin at the end of programming.

Table 12. Bus Hold Parameters

Parameter Conditions VCCIO Level Units

1.8 V 2.5 V 3.3 V

MinMaxMinMaxMinMax

Low sustaining current VIN > VIL (max) 30 50 70 μA

High sustaining current VIN < VIH (min) –30 –50 –70 μA

Low overdrive current 0 V < VIN < VCCIO 200 300 500 μA

High overdrive current 0 V < VIN < VCCIO –295 –435 –680 μA

26 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Two inverters implement the bus-hold circuitry in a loop that weakly

drives back to the I/O pin in user mode.

Figure 10 shows a block diagram of the bus-hold circuit.

Figure 10. Bus-Hold Circuit

PCI

Compatibility

MAX 7000B devices are compatible with PCI applications as well as all

3.3-V electrical specifications in the PCI Local Bus Specification

Revision 2.2 except for the clamp diode. While having multiple clamp

diodes on a signal trace may be redundant, designers can add an external

clamp diode to meet the specification. Table 13 shows the MAX 7000B

device speed grades that meet the PCI timing specifications.

Note:

(1) The EPM7256B and EPM7512B devices in a -5 speed grade meet all PCI timing

specifications for 66-MHz operation except the Input Setup Time to CLK—Bused

Signal parameter. However, these devices are within 1 ns of that parameter.

EPM7256B and EPM7512B devices meet all other 66-MHz PCI timing

specifications.

I/O

RBH

Bus Hold Circuit

Drive to

VCCIO level

Table 13. MAX 7000B Device Speed Grades that Meet PCI Timing

Specifications

Device Specification

33-MHz PCI 66-MHz PCI

EPM7032B All speed grades -3

EPM7064B All speed grades -3

EPM7128B All speed grades -4

EPM7256B All speed grades -5 (1)

EPM7512B All speed grades -5 (1)

Altera Corporation 27

MAX 7000B Programmable Logic Device Data Sheet

Power

Sequencing &

Hot-Socketing

Because MAX 7000B devices can be used in a mixed-voltage environment,

they have been designed specifically to tolerate any possible power-up

sequence. The VCCIO and VCCINT power planes can be powered in any

order.

Signals can be driven into MAX 7000B devices before and during power-

up (and power-down) without damaging the device. Additionally,

MAX 7000B devices do not drive out during power-up. Once operating

conditions are reached, MAX 7000B devices operate as specified by the

user.

MAX 7000B device I/O pins will not source or sink more than 300 µA of

DC current during power-up. All pins can be driven up to 4.1 V during

hot-socketing.

Design Security All MAX 7000B devices contain a programmable security bit that controls

access to the data programmed into the device. When this bit is

programmed, a design implemented in the device cannot be copied or

retrieved. This feature provides a high level of design security, because

programmed data within EEPROM cells is invisible. The security bit that

controls this function, as well as all other programmed data, is reset only

when the device is reprogrammed.

Generic Testing MAX 7000B devices are fully functionally tested. Complete testing of each

programmable EEPROM bit and all internal logic elements ensures 100%

programming yield. AC test measurements are taken under conditions

equivalent to those shown in Figure 11. Test patterns can be used and then

erased during early stages of the production flow.

28 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Figure 11. MAX 7000B AC Test Conditions

Operating

Conditions

Tables 14 through 17 provide information on absolute maximum ratings,

recommended operating conditions, operating conditions, and

capacitance for MAX 7000B devices.

To Test

System

C1 (includes jig

capacitance)

Device input

rise and fall

times < 2 ns

Device

Output

720 Ω

[521 Ω]

600 Ω

[481 Ω]

VCCIO

Power supply transients can affect AC

measurements. Simultaneous transitions

of multiple outputs should be avoided for

accurate measurement. Threshold tests

must not be performed under AC

conditions. Large-amplitude, fast-ground-

current transients normally occur as the

device outputs discharge the load

capacitances. When these transients flow

through the parasitic inductance between

the device ground pin and the test system

ground, significant reductions in

observable noise immunity can result.

Numbers in brackets are for 2.5-V

outputs. Numbers without brackets are for

3.3-V outputs. Switches S1 and S2 are

open for all tests except output disable

timing parameters.

Table 14. MAX 7000B Device Absolute Maximum Ratings Note (1)

Symbol Parameter Conditions Min Max Unit

VCCINT Supply voltage –0.5 3.6 V

VCCIO Supply voltage –0.5 3.6 V

VIDC input voltage (2) –2.0 4.6 V

IOUT DC output current, pe r pi n –33 50 mA

TSTG Storage temperature No bias –65 150 ° C

TAAmbient temperature Under bias –65 135 ° C

TJJunction temperature Under bias –65 135 ° C

Altera Corporation 29

MAX 7000B Programmable Logic Device Data Sheet

Table 15. MAX 7000B Device Recommended Operating Conditions

Symbol Parameter Conditions Min Max Unit

VCCINT Supply voltage for internal l ogic and

input buffers (10) 2.375 2.625 V

VCCIO Supply voltage for output drivers,

3.3-V operation 3.0 3.6 V

Supply voltage for output drivers,

2.5-V operation 2.375 2.625 V

Supply voltage for output drivers,

1.8-V operation 1.71 1.89 V

VCCISP Supply voltage during in-system

programming 2.375 2.625 V

VIInput voltage (3) –0.5 3.9 V

VOOutput voltage 0V

CCIO V

TAAmbient temperature For commercial use 070° C

For industrial use (11) –40 85 ° C

TJJunction temperature For commercial use 090° C

For industrial use (11) –40 105 ° C

tRInput rise time 40 ns

tFInput fall time 40 ns

30 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Table 16. MAX 7000B Device DC Operating Conditions Note (4)

Symbol Parameter Conditions Min Max Unit

VIH High-level input voltage for 3.3-V

TTL/CMOS 2.0 3.9 V

High-level input voltage for 2.5-V

TTL/CMOS 1.7 3.9 V

High-level input voltage for 1.8-V

TTL/CMOS 0.65 ×

VCCIO

3.9 V

VIL Low-level input voltage for 3.3-V

TTL/CMOS and PCI compliance –0.5 0.8 V

Low-level input voltage for 2.5-V

TTL/CMOS –0.5 0.7 V

Low-level input voltage for 1.8-V

TTL/CMOS –0.5 0.35 ×

VCCIO

VOH 3.3-V high-level TTL output voltage IOH = –8 mA DC, VCCIO = 3.00 V (5) 2.4 V

3.3-V high-level CMOS output

voltage IOH = –0.1 mA DC, VCCIO = 3.00 V (5) VCCIO –

0.2 V

2.5-V high-level output voltage IOH = –100 μA DC, VCCIO = 2.30 V (5) 2.1 V

IOH = –1 mA DC, VCCIO = 2.30 V (5) 2.0 V

IOH = –2 mA DC, VCCIO = 2.30 V (5) 1.7 V

1.8-V high-level output voltage IOH = –2 mA DC, VCCIO =1.65 V (5) 1.2 V

VOL 3.3-V low-level TTL output voltage IOL = 8 mA DC, VCCIO = 3.00 V (6) 0.4 V

3.3-V low-level CMOS output

voltage IOL = 0.1 mA DC, VCCIO = 3.00 V (6) 0.2 V

2.5-V low-level output voltage IOL = 100 μA DC, VCCIO = 2.30 V (6) 0.2 V

IOL = 1 mA DC, VCCIO = 2.30 V (6) 0.4 V

IOL = 2 mA DC, VCCIO = 2.30 V (6) 0.7 V

1.8-V low-level output voltage IOL = 2 mA DC, VCCIO = 1.7 V (6) 0.4 V

IIInput leakage current VI = –0.5 to 3.9 V (7) –10 10 μA

IOZ Tri-state output of f-state current VI = –0.5 to 3.9 V (7) –10 10 μA

RISP Value of I/O pin pull- up re si stor

during in-system programming or

during power up

VCCIO = 1.7 to 3.6 V (8) 20 74 k¾

Altera Corporation 31

MAX 7000B Programmable Logic Device Data Sheet

Notes to tables:

(1) See the Operating Requirements for Altera Devices Data Sheet.

(2) Minimum DC input voltage is –0.5 V. During transitions, the inputs may undershoot to –2.0 V or overshoot to 4.6 V

for input currents less than 100 mA and periods shorter than 20 ns.

(3) All pins, including dedicated inputs, I/O pins, and JTAG pins, may be driven before VCCINT and VCCIO are

powered.

(4) These values are specified under the Recommended Operating Conditions in Table 15 on page 29.

(5) The parameter is measured with 50% of the outputs each sourcing the specified current. The IOH parameter refers

to high-level TTL or CMOS output current.

(6) The parameter is measured with 50% of the outputs each sinking the specified current. The IOL parameter refers to

low-level TTL or CMOS output current.

(7) This value is specified for normal device operation. During power-up, the maximum leakage current is ±300 μA.

(8) This pull-up exists while devices are being programmed in-system and in unprogrammed devices during

power-up. The pull-up resistor is from the pins to VCCIO.

(9) Capacitance is measured at 25° C and is sample-tested only. Two of the dedicated input pins (OE1 and GCLRN) have

a maximum capacitance of 15 pF.

(10) The POR time for all 7000B devices does not exceed 100 μs. The sufficient VCCINT voltage level for POR is 2.375 V.

The device is fully initialized within the POR time after VCCINT reaches the sufficient POR voltage level.

(11) These devices support in-system programming for –40° to 100° C. For in-system programming support between

–40° and 0° C, contact Altera Applications.

Table 17. MAX 7000B Device Capacitance Note (9)

Symbol Parameter Conditions Min Max Unit

CIN Input pin capacitance VIN = 0 V, f = 1.0 MHz 8pF

CI/O I/O pin capacitance VOUT = 0 V, f = 1.0 MHz 8pF

32 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Figure 12 shows the typical output drive characteristics of MAX 7000B

devices.

Figure 12. Output Drive Characteristics of MAX 7000B Devices

VO Output Voltage (V)

1234

IOH

VCCINT = 2.5 V

VCCIO = 3.0 V

Room Temperature

120

150

Typical I

Output

Current (mA)

VO Output Voltage (V)

1234

VCCINT = 2.5 V

VCCIO = 2.5 V

IOH

Room Temperature

2.5-V VCCIO3.3-V VCCIO

Typical I

Output

Current (mA)

120

150

VO Output Voltage (V)

123

VCCINT = 2.5 V

VCCIO = 1.8 V

IOL

IOH

Room Temperature

1.8-V VCCIO

Typical I

Output

Current (mA)

120

150

Altera Corporation 33

MAX 7000B Programmable Logic Device Data Sheet

Timing Model MAX 7000B device timing can be analyzed with the Altera software, with

a variety of popular industry-standard EDA simulators and timing

analyzers, or with the timing model shown in Figure 13. MAX 7000B

devices have predictable internal delays that enable the designer to

determine the worst-case timing of any design. The Altera software

provides timing simulation, point-to-point delay prediction, and detailed

timing analysis for device-wide performance evaluation.

Figure 13. MAX 7000B Timing Model

The timing characteristics of any signal path can be derived from the

timing model and parameters of a particular device. External timing

parameters, which represent pin-to-pin timing delays, can be calculated

as the sum of internal parameters. Figure 14 shows the timing relationship

between internal and external delay parameters.

fSee Application Note 94 (Understanding MAX 7000 Timing) for more

information.

Logic Array

Delay

LAD

Output

Delay

OD3

OD2

OD1

ZX2

ZX3

Input

Delay

PRE

CLR

COMB

FSU

PIA

Delay

PIA

Shared

Expander Delay

SEXP

Control Delay

LAC

I/O

Delay

Global Control

Delay

GLOB

Internal Output

Enable Delay

IOE

Parallel

Expander Delay

PEXP

Fast

Input Delay

FIN

FIND

34 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Figure 14. MAX 7000B Switching Waveforms

Combinatorial Mode

Input Pin

I/O Pin

PIA Delay

Shared Expander

Delay

Logic Array

Input

Parallel Expander

Delay

Logic Array

Output

Output Pin

LAC

, t

LAD

PIA

PEXP

SEXP

COMB

Global Clock Mode

Global

Clock Pin

Global Clock

at Register

Data or Enable

(Logic Array Output)

GLOB

Array Clock Mode

Input or I/O Pin

Clock into PIA

Clock into

Logic Array

Clock at

Data from

Logic Array

to Logic Array

to Pin

ACH

ACL

PIA

CLR

, t

PRE

PIA

tR & tF < 2 ns. Inputs are

driven at 3.0 V for a logic

high and 0 V for a logic

low. All timing

characteristics are

measured at 1.5 V.

Altera Corporation 35

MAX 7000B Programmable Logic Device Data Sheet

Tables 18 through 32 show MAX 7000B device timing parameters.

Table 18. EPM7032B External Timing Parameters Notes (1)

Symbol Parameter Conditions Speed Grade Unit

-3.5 -5.0 -7.5

Min Max Min Max Min Max

tPD1 Input to non-registered

output C1 = 35 pF (2) 3.5 5.0 7.5 ns

tPD2 I/O input to non-registered

output C1 = 35 pF (2) 3.5 5.0 7.5 ns

tSU Global clock setup time (2) 2.1 3.0 4.5 ns

tHGlobal clock hold time (2) 0.0 0.0 0.0 ns

tFSU Global clock setup time of

fast input 1.0 1.0 1.5 ns

tFH Global clock hold time of

fast input 1.0 1.0 1.0 ns

tFZHSU Global clock setup time of

fast input with zero hold

time

2.0 2.5 3.0 ns

tFZHH Global clock hold time of

fast input with zero hold

time

0.0 0.0 0.0 ns

tCO1 Global clock to output

delay C1 = 35 pF 1.0 2.4 1.0 3.4 1.0 5.0 ns

tCH Global clock high time 1.5 2.0 3.0 ns

tCL Global clock low time 1.5 2.0 3.0 ns

tASU Array clock setup time (2) 0.9 1.3 1.9 ns

tAH Array clock hold time (2) 0.2 0.3 0.6 ns

tACO1 Array clock to output delay C1 = 35 pF (2) 1.0 3.6 1.0 5.1 1.0 7.6 ns

tACH Array clock high time 1.5 2.0 3.0 ns

tACL Array clock low time 1.5 2.0 3.0 ns

tCPPW Minimum pulse width for

clear and preset 1.5 2.0 3.0 ns

tCNT Minimum global clock

period (2) 3.3 4.7 7.0 ns

fCNT Maximum internal global

clock frequency (2), (3) 303.0 212.8 142.9 MHz

tACNT Minimum array clock

period (2) 3.3 4.7 7.0 ns

fACNT Maximum internal array

clock frequency (2), (3) 303.0 212.8 142.9 MHz

36 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Table 19. EPM7032B Internal Timing Parameters Notes (1)

Symbol Parameter Conditions Speed Grade Unit

-3.5 -5.0 -7.5

MinMaxMinMaxMinMax

tIN Input pad and buffer delay 0.3 0.5 0.7 ns

tIO I/O input pad and buffer delay 0.3 0.5 0.7 ns

tFIN Fast input delay 0.9 1.3 2.0 ns

tFIND Programmable delay adder fo r

fast input 1.0 1.5 1.5 ns

tSEXP Shared expander delay 1.5 2.1 3.2 ns

tPEXP Parallel expander delay 0.4 0.6 0.9 ns

tLAD Logic array delay 1.4 2.0 3.1 ns

tLAC Logic control array delay 1.2 1.7 2.6 ns

tIOE Internal output enable delay 0.1 0.2 0.3 ns

tOD1 Output buffer and pad de lay

slow slew rate = off

VCCIO = 3.3 V

C1 = 35 pF 0.9 1.2 1.8 ns

tOD3 Output buffer and pad delay

slow slew rate = on

VCCIO = 2.5 V or 3. 3 V

C1 = 35 pF 5.9 6.2 6.8 ns

tZX1 Output buffer enab le delay

slow slew rate = off

VCCIO = 3.3 V

C1 = 35 pF 1.6 2.2 3.4 ns

tZX3 Output buffer enab le delay

slow slew rate = on

VCCIO = 2.5 V or 3. 3 V

C1 = 35 pF 6.6 7.2 8.4 ns

tXZ Output buffer disable delay C1 = 5 pF 1.6 2.2 3.4 ns

tSU Register setup time 0.7 1.1 1.6 ns

tHRegister hold time 0.4 0.5 0.9 ns

tFSU Register setup time of fast input 0.8 0.8 1.1 ns

tFH Register hold time of fast input 1.2 1.2 1.4 ns

tRD Register delay 0.5 0.6 0.9 ns

tCOMB Combinatorial delay 0.2 0.3 0.5 ns

tIC Array clock delay 1.2 1.8 2.8 ns

tEN Register enable time 1.2 1.7 2.6 ns

tGLOB Global control delay 0.7 1.1 1.6 ns

tPRE Register preset time 1.0 1.3 1.9 ns

tCLR Register clear time 1.0 1.3 1.9 ns

tPIA PIA delay (2) 0.7 1.0 1.4 ns

tLPA Low-power adder (4) 1.5 2.1 3.2 ns

Altera Corporation 37

MAX 7000B Programmable Logic Device Data Sheet

Table 20. EPM7032B Selectable I/O Standard Timing Adder Delays Notes (1)

I/O Standard Parameter Speed Grade Unit

-3.5 -5.0 -7.5

Min Max Min Max Min Max

3.3 V TTL/CMOS Input to (PIA) 0.0 0.0 0.0 ns

Input to global clock and clear 0.0 0.0 0.0 ns

Input to fast input register 0.0 0.0 0.0 ns

All outputs 0.0 0.0 0.0 ns

2.5 V TTL/CMOS Input to PIA 0.3 0.4 0.6 ns

Input to global clock and clear 0.3 0.4 0.6 ns

Input to fast input register 0.2 0.3 0.4 ns

All outputs 0.2 0.3 0.4 ns

1.8 V TTL/CMOS Input to PIA 0.5 0.8 1.1 ns

Input to global clock and clear 0.5 0.8 1.1 ns

Input to fast input register 0.4 0.5 0.8 ns

All outputs 1.2 1.8 2.6 ns

SSTL-2 Class I Input to PIA 1.3 1.9 2.8 ns

Input to global clock and clear 1.2 1.8 2.6 ns

Input to fast input register 0.9 1.3 1.9 ns

All outputs 0.0 0.0 0.0 ns

SSTL-2 Class II Input to PIA 1.3 1.9 2.8 ns

Input to global clock and clear 1.2 1.8 2.6 ns

Input to fast input register 0.9 1.3 1.9 ns

All outputs –0.1 –0.1 –0.2 ns

SSTL-3 Class I Input to PIA 1.2 1.8 2.6 ns

Input to global clock and clear 0.9 1.3 1.9 ns

Input to fast input register 0.8 1.1 1.7 ns

All outputs 0.0 0.0 0.0 ns

SSTL-3 Class II Input to PIA 1.2 1.8 2.6 ns

Input to global clock and clear 0.9 1.3 1.9 ns

Input to fast input register 0.8 1.1 1.7 ns

All outputs 0.0 0.0 0.0 ns

GTL+ Input to PIA 1.6 2.3 3.4 ns

Input to global clock and clear 1.6 2.3 3.4 ns

Input to fast input register 1.5 2.1 3.2 ns

All outputs 0.0 0.0 0.0 ns

38 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Notes to tables:

(1) These values are specified under the Recommended Operating Conditions in Table 15 on page 29. See Figure 14 for

more information on switching waveforms.

(2) These values are specified for a PIA fan-out of all LABs.

(3) Measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB.

(4) The tLPA parameter must be added to the tLAD, tLAC, tIC, tACL, tCPPW, tEN, and tSEXP parameters for macrocells

running in low-power mode.

PCI Input to PIA 0.0 0.0 0.0 ns

Input to global clock and clear 0.0 0.0 0.0 ns

Input to fast input register 0.0 0.0 0.0 ns

All outputs 0.0 0.0 0.0 ns

Table 20. EPM7032B Selectable I/O Standard Timing Adder Delays Notes (1)

I/O Standard Parameter Speed Grade Unit

-3.5 -5.0 -7.5

Min Max Min Max Min Max

Altera Corporation 39

MAX 7000B Programmable Logic Device Data Sheet

Table 21. EPM7064B External Timing Parameters Note (1)

Symbol Parameter Conditions Speed Grade Unit

-3 -5 -7

Min Max Min Max Min Max

tPD1 Input to non-registered

output C1 = 35 pF (2) 3.5 5.0 7.5 ns

tPD2 I/O input to non-registered

output C1 = 35 pF (2) 3.5 5.0 7.5 ns

tSU Global clock setup time (2) 2.1 3.0 4.5 ns

tHGlobal clock hold time (2) 0.0 0.0 0.0 ns

tFSU Global clock setup time of

fast input 1.0 1.0 1.5 ns

tFH Global clock hold time of

fast input 1.0 1.0 1.0 ns

tFZHSU Global clock setup time of

fast input with zero hold

time

2.0 2.5 3.0 ns

tFZHH Global clock hold time of

fast input with zero hold

time

0.0 0.0 0.0 ns

tCO1 Global clock to output

delay C1 = 35 pF 1.0 2.4 1.0 3.4 1.0 5.0 ns

tCH Global clock high time 1.5 2.0 3.0 ns

tCL Global clock low time 1.5 2.0 3.0 ns

tASU Array clock setup time (2) 0.9 1.3 1.9 ns

tAH Array clock hold time (2) 0.2 0.3 0.6 ns

tACO1 Array clock to output delay C1 = 35 pF (2) 1.0 3.6 1.0 5.1 1.0 7.6 ns

tACH Array clock high time 1.5 2.0 3.0 ns

tACL Array clock low time 1.5 2.0 3.0 ns

tCPPW Minimum pulse width for

clear and preset 1.5 2.0 3.0 ns

tCNT Minimum global clock

period (2) 3.3 4.7 7.0 ns

fCNT Maximum internal global

clock frequency (2), (3) 303.0 212.8 142.9 MHz

tACNT Minimum array clock

period (2) 3.3 4.7 7.0 ns

fACNT Maximum internal array

clock frequency (2), (3) 303.0 212.8 142.9 MHz

40 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Table 22. EPM7064B Internal Timing Parameters Note (1)

Symbol Parameter Conditions Speed Grade Unit

-3 -5 -7

MinMaxMinMaxMinMax

tIN Input pad and buffer delay 0.3 0.5 0.7 ns

tIO I/O input pad and buffer delay 0.3 0.5 0.7 ns

tFIN Fast input delay 0.9 1.3 2.0 ns

tFIND Programmable delay adder fo r

fast input 1.0 1.5 1.5 ns

tSEXP Shared expander delay 1.5 2.1 3.2 ns

tPEXP Parallel expander delay 0.4 0.6 0.9 ns

tLAD Logic array delay 1.4 2.0 3.1 ns

tLAC Logic control array delay 1.2 1.7 2.6 ns

tIOE Internal output enable delay 0.1 0.2 0.3 ns

tOD1 Output buffer and pad de lay

slow slew rate = off

VCCIO = 3.3 V

C1 = 35 pF 0.9 1.2 1.8 ns

tOD3 Output buffer and pad delay

slow slew rate = on

VCCIO = 2.5 V or 3. 3 V

C1 = 35 pF 5.9 6.2 6.8 ns

tZX1 Output buffer enab le delay

slow slew rate = off

VCCIO = 3.3 V

C1 = 35 pF 1.6 2.2 3.4 ns

tZX3 Output buffer enab le delay

slow slew rate = on

VCCIO = 2.5 V or 3. 3 V

C1 = 35 pF 6.6 7.2 8.4 ns

tXZ Output buffer disable delay C1 = 5 pF 1.6 2.2 3.4 ns

tSU Register setup time 0.7 1.1 1.6 ns

tHRegister hold time 0.4 0.5 0.9 ns

tFSU Register setup time of fast input 0.8 0.8 1.1 ns

tFH Register hold time of fast input 1.2 1.2 1.4 ns

tRD Register delay 0.5 0.6 0.9 ns

tCOMB Combinatorial delay 0.2 0.3 0.5 ns

tIC Array clock delay 1.2 1.8 2.8 ns

tEN Register enable time 1.2 1.7 2.6 ns

tGLOB Global control delay 0.7 1.1 1.6 ns

tPRE Register preset time 1.0 1.3 1.9 ns

tCLR Register clear time 1.0 1.3 1.9 ns

tPIA PIA delay (2) 0.7 1.0 1.4 ns

tLPA Low-power adder (4) 1.5 2.1 3.2 ns

Altera Corporation 41

MAX 7000B Programmable Logic Device Data Sheet

Table 23. EPM7064B Selectable I/O Standard Timing Adder Delays (Part 1 of 2) Note (1)

I/O Standard Parameter Speed Grade Unit

-3 -5 -7

Min Max Min Max Min Max

3.3 V TTL/CMOS Input to PIA 0.0 0.0 0.0 ns

Input to global clock and clear 0.0 0.0 0.0 ns

Input to fast input register 0.0 0.0 0.0 ns

All outputs 0.0 0.0 0.0 ns

2.5 V TTL/CMOS Input to PIA 0.3 0.4 0.6 ns

Input to global clock and clear 0.3 0.4 0.6 ns

Input to fast input register 0.2 0.3 0.4 ns

All outputs 0.2 0.3 0.4 ns

1.8 V TTL/CMOS Input to PIA 0.5 0.7 1.1 ns

Input to global clock and clear 0.5 0.7 1.1 ns

Input to fast input register 0.4 0.6 0.9 ns

All outputs 1.2 1.7 2.6 ns

SSTL-2 Class I Input to PIA 1.3 1.9 2.8 ns

Input to global clock and clear 1.2 1.7 2.6 ns

Input to fast input register 0.9 1.3 1.9 ns

All outputs 0.0 0.0 0.0 ns

SSTL-2 Class II Input to PIA 1.3 1.9 2.8 ns

Input to global clock and clear 1.2 1.7 2.6 ns

Input to fast input register 0.9 1.3 1.9 ns

All outputs –0.1 –0.1 –0.2 ns

SSTL-3 Class I Input to PIA 1.2 1.7 2.6 ns

Input to global clock and clear 0.9 1.3 1.9 ns

Input to fast input register 0.8 1.1 1.7 ns

All outputs 0.0 0.0 0.0 ns

SSTL-3 Class II Input to PIA 1.2 1.7 2.6 ns

Input to global clock and clear 0.9 1.3 1.9 ns

Input to fast input register 0.8 1.1 1.7 ns

All outputs 0.0 0.0 0.0 ns

GTL+ Input to PIA 1.6 2.3 3.4 ns

Input to global clock and clear 1.6 2.3 3.4 ns

Input to fast input register 1.5 2.1 3.2 ns

All outputs 0.0 0.0 0.0 ns

42 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Notes to tables:

(1) These values are specified under the Recommended Operating Conditions in Table 15 on page 29. See Figure 14 for

more information on switching waveforms.

(2) These values are specified for a PIA fan-out of all LABs.

(3) Measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB.

(4) The tLPA parameter must be added to the tLAD, tLAC, tIC, tACL, tCPPW, tEN, and tSEXP parameters for macrocells

running in low-power mode.

PCI Input to PIA 0.0 0.0 0.0 ns

Input to global clock and clear 0.0 0.0 0.0 ns

Input to fast input register 0.0 0.0 0.0 ns

All outputs 0.0 0.0 0.0 ns

Table 23. EPM7064B Selectable I/O Standard Timing Adder Delays (Part 2 of 2) Note (1)

I/O Standard Parameter Speed Grade Unit

-3 -5 -7

Min Max Min Max Min Max

Altera Corporation 43

MAX 7000B Programmable Logic Device Data Sheet

Table 24. EPM7128B External Timing Parameters Note (1)

Symbol Parameter Conditions Speed Grade Unit

-4 -7 -10

Min Max Min Max Min Max

tPD1 Input to non-registered

output C1 = 35 pF (2) 4.0 7.5 10.0 ns

tPD2 I/O input to non-registered

output C1 = 35 pF (2) 4.0 7.5 10.0 ns

tSU Global clock setup time (2) 2.5 4.5 6.1 ns

tHGlobal clock hold time (2) 0.0 0.0 0.0 ns

tFSU Global clock setup time of

fast input 1.0 1.5 1.5 ns

tFH Global clock hold time of

fast input 1.0 1.0 1.0 ns

tFZHSU Global clock setup time of

fast input with zero hold

time

2.0 3.0 3.0 ns

tFZHH Global clock hold time of

fast input with zero hold

time

0.0 0.0 0.0 ns

tCO1 Global clock to output

delay C1 = 35 pF 1.0 2.8 1.0 5.7 1.0 7.5 ns

tCH Global clock high time 1.5 3.0 4.0 ns

tCL Global clock low time 1.5 3.0 4.0 ns

tASU Array clock setup time (2) 1.2 2.0 2.8 ns

tAH Array clock hold time (2) 0.2 0.7 0.9 ns

tACO1 Array clock to output delay C1 = 35 pF (2) 1.0 4.1 1.0 8.2 1.0 10.8 ns

tACH Array clock high time 1.5 3.0 4.0 ns

tACL Array clock low time 1.5 3.0 4.0 ns

tCPPW Minimum pulse width for

clear and preset 1.5 3.0 4.0 ns

tCNT Minimum global clock

period (2) 4.1 7.9 10.6 ns

fCNT Maximum internal global

clock frequency (2), (3) 243.9 126.6 94.3 MHz

tACNT Minimum array clock

period (2) 4.1 7.9 10.6 ns

fACNT Maximum internal array

clock frequency (2), (3) 243.9 126.6 94.3 MHz

44 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Table 25. EPM7128B Internal Timing Parameters Note (1)

Symbol Parameter Conditions Speed Grade Unit

-4 -7 -10

Min Max Min Max Min Max

tIN Input pad and buffer de lay 0.3 0.6 0.8 ns

tIO I/O input pad and buffer delay 0.3 0.6 0.8 ns

tFIN Fast input delay 1.3 2.9 3.7 ns

tFIND Programmable del ay adder for

fast input 1.0 1.5 1.5 ns

tSEXP Shared expander delay 1.5 2.8 3.8 ns

tPEXP Parallel expander delay 0.4 0.8 1.0 ns

tLAD Logic array delay 1.6 2.9 3.8 ns

tLAC Logic control array delay 1.4 2.6 3.4 ns

tIOE Internal output enable delay 0.1 0.3 0.4 ns

tOD1 Output buffer and pad delay

slow slew rate = off

VCCIO = 3.3 V

C1 = 35 pF 0.9 1.7 2.2 ns

tOD3 Output buffer and pad delay

slow slew rate = on

VCCIO = 2.5 V or 3.3 V

C1 = 35 pF 5.9 6.7 7.2 ns

tZX1 Output buffer enable delay

slow slew rate = off

VCCIO = 3.3 V

C1 = 35 pF 1.8 3.3 4.4 ns

tZX3 Output buffer enable delay

slow slew rate = on

VCCIO = 2.5 V or 3.3 V

C1 = 35 pF 6.8 8.3 9.4 ns

tXZ Output buffer disable delay C1 = 5 pF 1.8 3.3 4.4 ns

tSU Register setup time 1.0 1.9 2.6 ns

tHRegister hold time 0.4 0.8 1.1 ns

tFSU Register setup time of fast inpu t 0.8 0.9 0.9 ns

tFH Register hold time of fast input 1.2 1.6 1.6 ns

tRD Register delay 0.5 1.1 1.4 ns

tCOMB Combinatorial delay 0.2 0.3 0.4 ns

tIC Array clock delay 1.4 2.8 3.6 ns

tEN Register enable time 1.4 2.6 3.4 ns

tGLOB Global control delay 1.1 2.3 3.1 ns

tPRE Register preset time 1.0 1.9 2.6 ns

tCLR Register clear time 1.0 1.9 2.6 ns

tPIA PIA delay (2) 1.0 2.0 2.8 ns

tLPA Low-power adder (4) 1.5 2.8 3.8 ns

Altera Corporation 45

MAX 7000B Programmable Logic Device Data Sheet

Table 26. EPM7128B Selectable I/O Standard Timing Adder Delays (Part 1 of 2) Note (1)

I/O Standard Parameter Speed Grade Unit

-4 -7 -10

Min Max Min Max Min Max

3.3 V TTL/CMOS Input to PIA 0.0 0.0 0.0 ns

Input to global clock and clear 0.0 0.0 0.0 ns

Input to fast input register 0.0 0.0 0.0 ns

All outputs 0.0 0.0 0.0 ns

2.5 V TTL/CMOS Input to PIA 0.3 0.6 0.8 ns

Input to global clock and clear 0.3 0.6 0.8 ns

Input to fast input register 0.2 0.4 0.5 ns

All outputs 0.2 0.4 0.5 ns

1.8 V TTL/CMOS Input to PIA 0.5 0.9 1.3 ns

Input to global clock and clear 0.5 0.9 1.3 ns

Input to fast input register 0.4 0.8 1.0 ns

All outputs 1.2 2.3 3.0 ns

SSTL-2 Class I Input to PIA 1.4 2.6 3.5 ns

Input to global clock and clear 1.2 2.3 3.0 ns

Input to fast input register 1.0 1.9 2.5 ns

All outputs 0.0 0.0 0.0 ns

SSTL-2 Class II Input to PIA 1.4 2.6 3.5 ns

Input to global clock and clear 1.2 2.3 3.0 ns

Input to fast input register 1.0 1.9 2.5 ns

All outputs –0.1 –0.2 –0.3 ns

SSTL-3 Class I Input to PIA 1.3 2.4 3.3 ns

Input to global clock and clear 1.0 1.9 2.5 ns

Input to fast input register 0.9 1.7 2.3 ns

All outputs 0.0 0.0 0.0 ns

SSTL-3 Class II Input to PIA 1.3 2.4 3.3 ns

Input to global clock and clear 1.0 1.9 2.5 ns

Input to fast input register 0.9 1.7 2.3 ns

All outputs 0.0 0.0 0.0 ns

GTL+ Input to PIA 1.7 3.2 4.3 ns

Input to global clock and clear 1.7 3.2 4.3 ns

Input to fast input register 1.6 3.0 4.0 ns

All outputs 0.0 0.0 0.0 ns

46 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Notes to tables:

(1) These values are specified under the Recommended Operating Conditions in Table 15 on page 29. See Figure 14 for

more information on switching waveforms.

(2) These values are specified for a PIA fan-out of one LAB (16 macrocells). For each additional LAB fan-out in these

devices, add an additional 0.1 ns to the PIA timing value.

(3) Measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB.

(4) The tLPA parameter must be added to the tLAD, tLAC, tIC, tACL, tCPPW, tEN, and tSEXP parameters for macrocells

running in low-power mode.

PCI Input to PIA 0.0 0.0 0.0 ns

Input to global clock and clear 0.0 0.0 0.0 ns

Input to fast input register 0.0 0.0 0.0 ns

All outputs 0.0 0.0 0.0 ns

Table 26. EPM7128B Selectable I/O Standard Timing Adder Delays (Part 2 of 2) Note (1)

I/O Standard Parameter Speed Grade Unit

-4 -7 -10

Min Max Min Max Min Max

Altera Corporation 47

MAX 7000B Programmable Logic Device Data Sheet

Table 27. EPM7256B External Timing Parameters Note (1)

Symbol Parameter Conditions Speed Grade Unit

-5 -7 -10

Min Max Min Max Min Max

tPD1 Input to non-registered

output C1 = 35 pF (2) 5.0 7.5 10.0 ns

tPD2 I/O input to non-registered

output C1 = 35 pF (2) 5.0 7.5 10.0 ns

tSU Global clock setup time (2) 3.3 4.8 6.6 ns

tHGlobal clock hold time (2) 0.0 0.0 0.0 ns

tFSU Global clock setup time of

fast input 1.0 1.5 1.5 ns

tFH Global clock hold time for

fast input 1.0 1.0 1.0 ns

tFZHSU Global clock setup time of

fast input with zero hold

time

2.5 3.0 3.0 ns

tFZHH Global clock hold time of

fast input with zero hold

time

0.0 0.0 0.0 ns

tCO1 Global clock to output

delay C1 = 35 pF 1.0 3.3 1.0 5.1 1.0 6.7 ns

tCH Global clock high time 2.0 3.0 4.0 ns

tCL Global clock low time 2.0 3.0 4.0 ns

tASU Array clock setup time (2) 1.4 2.0 2.8 ns

tAH Array clock hold time (2) 0.4 0.8 1.0 ns

tACO1 Array clock to output delay C1 = 35 pF (2) 1.0 5.2 1.0 7.9 1.0 10.5 ns

tACH Array clock high time 2.0 3.0 4.0 ns

tACL Array clock low time 2.0 3.0 4.0 ns

tCPPW Minimum pulse width for

clear and preset 2.0 3.0 4.0 ns

tCNT Minimum global clock

period (2) 5.3 7.9 10.6 ns

fCNT Maximum internal global

clock frequency (2), (3) 188.7 126.6 94.3 MHz

tACNT Minimum array clock

period (2) 5.3 7.9 10.6 ns

fACNT Maximum internal array

clock frequency (2), (3) 188.7 126.6 94.3 MHz

48 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Table 28. EPM7256B Internal Timing Parameters Note (1)

Symbol Parameter Conditions Speed Grade Unit

-5 -7 -10

Min Max Min Max Min Max

tIN Input pad and buffer de lay 0.4 0.6 0.8 ns

tIO I/O input pad and buffer delay 0.4 0.6 0.8 ns

tFIN Fast input delay 1.5 2.5 3.1 ns

tFIND Programmable del ay adder for

fast input 1.5 1.5 1.5 ns

tSEXP Shared expander delay 1.5 2.3 3.0 ns

tPEXP Parallel expander delay 0.4 0.6 0.8 ns

tLAD Logic array delay 1.7 2.5 3.3 ns

tLAC Logic control array delay 1.5 2.2 2.9 ns

tIOE Internal output enable delay 0.1 0.2 0.3 ns

tOD1 Output buffer and pad delay

slow slew rate = off

VCCIO = 3.3 V

C1 = 35 pF 0.9 1.4 1.9 ns

tOD3 Output buffer and pad delay

slow slew rate = on

VCCIO = 2.5 V or 3.3 V

C1 = 35 pF 5.9 6.4 6.9 ns

tZX1 Output buffer enable delay

slow slew rate = off

VCCIO = 3.3 V

C1 = 35 pF 2.2 3.3 4.5 ns

tZX3 Output buffer enable delay

slow slew rate = on

VCCIO = 2.5 V or 3.3 V

C1 = 35 pF 7.2 8.3 9.5 ns

tXZ Output buffer disable delay C1 = 5 pF 2.2 3.3 4.5 ns

tSU Register setup time 1.2 1.8 2.5 ns

tHRegister hold time 0.6 1.0 1.3 ns

tFSU Register setup time of fast inpu t 0.8 1.1 1.1 ns

tFH Register hold time of fast input 1.2 1.4 1.4 ns

tRD Register delay 0.7 1.0 1.3 ns

tCOMB Combinatorial delay 0.3 0.4 0.5 ns

tIC Array clock delay 1.5 2.3 3.0 ns

tEN Register enable time 1.5 2.2 2.9 ns

tGLOB Global control delay 1.3 2.1 2.7 ns

tPRE Register preset time 1.0 1.6 2.1 ns

tCLR Register clear time 1.0 1.6 2.1 ns

tPIA PIA delay (2) 1.7 2.6 3.3 ns

tLPA Low-power adder (4) 2.0 3.0 4.0 ns

Altera Corporation 49

MAX 7000B Programmable Logic Device Data Sheet

Table 29. EPM7256B Selectable I/O Standard Timing Adder Delays (Part 1 of 2) Note (1)

I/O Standard Parameter Speed Grade Unit

-5 -7 -10

Min Max Min Max Min Max

3.3 V TTL/CMOS Input to PIA 0.0 0.0 0.0 ns

Input to global clock and clear 0.0 0.0 0.0 ns

Input to fast input register 0.0 0.0 0.0 ns

All outputs 0.0 0.0 0.0 ns

2.5 V TTL/CMOS Input to PIA 0.4 0.6 0.8 ns

Input to global clock and clear 0.3 0.5 0.6 ns

Input to fast input register 0.2 0.3 0.4 ns

All outputs 0.2 0.3 0.4 ns

1.8 V TTL/CMOS Input to PIA 0.6 0.9 1.2 ns

Input to global clock and clear 0.6 0.9 1.2 ns

Input to fast input register 0.5 0.8 1.0 ns

All outputs 1.3 2.0 2.6 ns

SSTL-2 Class I Input to PIA 1.5 2.3 3.0 ns

Input to global clock and clear 1.3 2.0 2.6 ns

Input to fast input register 1.1 1.7 2.2 ns

All outputs 0.0 0.0 0.0 ns

SSTL-2 Class II Input to PIA 1.5 2.3 3.0 ns

Input to global clock and clear 1.3 2.0 2.6 ns

Input to fast input register 1.1 1.7 2.2 ns

All outputs –0.1 –0.2 –0.2 ns

SSTL-3 Class I Input to PIA 1.4 2.1 2.8 ns

Input to global clock and clear 1.1 1.7 2.2 ns

Input to fast input register 1.0 1.5 2.0 ns

All outputs 0.0 0.0 0.0 ns

SSTL-3 Class II Input to PIA 1.4 2.1 2.8 ns

Input to global clock and clear 1.1 1.7 2.2 ns

Input to fast input register 1.0 1.5 2.0 ns

All outputs 0.0 0.0 0.0 ns

GTL+ Input to PIA 1.8 2.7 3.6 ns

Input to global clock and clear 1.8 2.7 3.6 ns

Input to fast input register 1.7 2.6 3.4 ns

All outputs 0.0 0.0 0.0 ns

50 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Notes to tables:

(1) These values are specified under the Recommended Operating Conditions in Table 15 on page 29. See Figure 14 for

more information on switching waveforms.

(2) These values are specified for a PIA fan-out of one LAB (16 macrocells). For each additional LAB fan-out in these

devices, add an additional 0.1 ns to the PIA timing value.

(3) Measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB.

(4) The tLPA parameter must be added to the tLAD, tLAC, tIC, tACL, tCPPW, tEN, and tSEXP parameters for macrocells

running in low-power mode.

PCI Input to PIA 0.0 0.0 0.0 ns

Input to global clock and clear 0.0 0.0 0.0 ns

Input to fast input register 0.0 0.0 0.0 ns

All outputs 0.0 0.0 0.0 ns

Table 29. EPM7256B Selectable I/O Standard Timing Adder Delays (Part 2 of 2) Note (1)

I/O Standard Parameter Speed Grade Unit

-5 -7 -10

Min Max Min Max Min Max

Altera Corporation 51

MAX 7000B Programmable Logic Device Data Sheet

Table 30. EPM7512B External Timing Parameters Note (1)

Symbol Parameter Conditions Speed Grade Unit

-5 -7 -10

Min Max Min Max Min Max

tPD1 Input to non-registered

output C1 = 35 pF (2) 5.5 7.5 10.0 ns

tPD2 I/O input to non-registered

output C1 = 35 pF (2) 5.5 7.5 10.0 ns

tSU Global clock setup time (2) 3.6 4.9 6.5 ns

tHGlobal clock hold time (2) 0.0 0.0 0.0 ns

tFSU Global clock setup time of

fast input 1.0 1.5 1.5 ns

tFH Global clock hold time of

fast input 1.0 1.0 1.0 ns

tFZHSU Global clock setup time of

fast input with zero hold

time

2.5 3.0 3.0 ns

tFZHH Global clock hold time of

fast input with zero hold

time

0.0 0.0 0.0 ns

tCO1 Global clock to output

delay C1 = 35 pF 1.0 3.7 1.0 5.0 1.0 6.7 ns

tCH Global clock high time 3.0 3.0 4.0 ns

tCL Global clock low time 3.0 3.0 4.0 ns

tASU Array clock setup time (2) 1.4 1.9 2.5 ns

tAH Array clock hold time (2) 0.5 0.6 0.8 ns

tACO1 Array clock to output delay C1 = 35 pF (2) 1.0 5.9 1.0 8.0 1.0 10.7 ns

tACH Array clock high time 3.0 3.0 4.0 ns

tACL Array clock low time 3.0 3.0 4.0 ns

tCPPW Minimum pulse width for

clear and preset 3.0 3.0 4.0 ns

tCNT Minimum global clock

period (2) 6.1 8.4 11.1 ns

fCNT Maximum internal global

clock frequency (2), (3) 163.9 119.0 90.1 MHz

tACNT Minimum array clock

period (2) 6.1 8.4 11.1 ns

fACNT Maximum internal array

clock frequency (2), (3) 163.9 119.0 90.1 MHz

52 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Table 31. EPM7512B Internal Timing Parameters Note (1)

Symbol Parameter Conditions Speed Grade Unit

-5 -7 -10

Min Max Min Max Min Max

tIN Input pad and buffer de lay 0.3 0.3 0.5 ns

tIO I/O input pad and buffer delay 0.3 0.3 0.5 ns

tFIN Fast input delay 2.2 3.2 4.0 ns

tFIND Programmable del ay adder for

fast input 1.5 1.5 1.5 ns

tSEXP Shared expander delay 1.5 2.1 2.7 ns

tPEXP Parallel expander delay 0.4 0.5 0.7 ns

tLAD Logic array delay 1.7 2.3 3.0 ns

tLAC Logic control array delay 1.5 2.0 2.6 ns

tIOE Internal output enable delay 0.1 0.2 0.2 ns

tOD1 Output buffer and pad delay

slow slew rate = off

VCCIO = 3.3 V

C1 = 35 pF 0.9 1.2 1.6 ns

tOD3 Output buffer and pad delay

slow slew rate = on

VCCIO = 2.5 V or 3.3 V

C1 = 35 pF 5.9 6.2 6.6 ns

tZX1 Output buffer enable delay

slow slew rate = off

VCCIO = 3.3 V

C1 = 35 pF 2.8 3.8 5.0 ns

tZX3 Output buffer enable delay

slow slew rate = on

VCCIO = 2.5 V or 3.3 V

C1 = 35 pF 7.8 8.8 10.0 ns

tXZ Output buffer disable delay C1 = 5 pF 2.8 3.8 5.0 ns

tSU Register setup time 1.5 2.0 2.6 ns

tHRegister hold time 0.4 0.5 0.7 ns

tFSU Register setup time of fast inpu t 0.8 1.1 1.1 ns

tFH Register hold time of fast input 1.2 1.4 1.4 ns

tRD Register delay 0.5 0.7 1.0 ns

tCOMB Combinatorial delay 0.2 0.3 0.4 ns

tIC Array clock delay 1.8 2.4 3.1 ns

tEN Register enable time 1.5 2.0 2.6 ns

tGLOB Global control delay 2.0 2.8 3.6 ns

tPRE Register preset time 1.0 1.4 1.9 ns

tCLR Register clear time 1.0 1.4 1.9 ns

tPIA PIA delay (2) 2.4 3.4 4.5 ns

tLPA Low-power adder (4) 2.0 2.7 3.6 ns

Altera Corporation 53

MAX 7000B Programmable Logic Device Data Sheet

Table 32. EPM7512B Selectable I/O Standard Timing Adder Delays (Part 1 of 2) Note (1)

I/O Standard Parameter Speed Grade Unit

-5 -7 -10

Min Max Min Max Min Max

3.3 V TTL/CMOS Input to PIA 0.0 0.0 0.0 ns

Input to global clock and clear 0.0 0.0 0.0 ns

Input to fast input register 0.0 0.0 0.0 ns

All outputs 0.0 0.0 0.0 ns

2.5 V TTL/CMOS Input to PIA 0.4 0.5 0.7 ns

Input to global clock and clear 0.3 0.4 0.5 ns

Input to fast input register 0.2 0.3 0.3 ns

All outputs 0.2 0.3 0.3 ns

1.8 V TTL/CMOS Input to PIA 0.7 1.0 1.3 ns

Input to global clock and clear 0.6 0.8 1.0 ns

Input to fast input register 0.5 0.6 0.8 ns

All outputs 1.3 1.8 2.3 ns

SSTL-2 Class I Input to PIA 1.5 2.0 2.7 ns

Input to global clock and clear 1.4 1.9 2.5 ns

Input to fast input register 1.1 1.5 2.0 ns

All outputs 0.0 0.0 0.0 ns

SSTL-2 Class II Input to PIA 1.5 2.0 2.7 ns

Input to global clock and clear 1.4 1.9 2.5 ns

Input to fast input register 1.1 1.5 2.0 ns

All outputs –0.1 –0.1 –0.2 ns

SSTL-3 Class I Input to PIA 1.4 1.9 2.5 ns

Input to global clock and clear 1.2 1.6 2.2 ns

Input to fast input register 1.0 1.4 1.8 ns

All outputs 0.0 0.0 0.0 ns

SSTL-3 Class II Input to PIA 1.4 1.9 2.5 ns

Input to global clock and clear 1.2 1.6 2.2 ns

Input to fast input register 1.0 1.4 1.8 ns

All outputs 0.0 0.0 0.0 ns

GTL+ Input to PIA 1.8 2.5 3.3 ns

Input to global clock and clear 1.9 2.6 3.5 ns

Input to fast input register 1.8 2.5 3.3 ns

All outputs 0.0 0.0 0.0 ns

54 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Notes to tables:

(1) These values are specified under the Recommended Operating Conditions in Table 15 on page 29. See Figure 14 for

more information on switching waveforms.

(2) These values are specified for a PIA fan-out of one LAB (16 macrocells). For each additional LAB fan-out in these

devices, add an additional 0.12 ns to the PIA timing value.

(3) Measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB.

(4) The tLPA parameter must be added to the tLAD, tLAC, tIC, tACL, tCPPW, tEN, and tSEXP parameters for macrocells

running in low-power mode.

Power

Consumption

Supply power (P) versus frequency (fMAX, in MHz) for MAX 7000B

devices is calculated with the following equation:

P = PINT + PIO = ICCINT × VCC + PIO

The PIO value, which depends on the device output load characteristics

and switching frequency, can be calculated using the guidelines given in

Application Note 74 (Evaluating Power for Altera Devices).

PCI Input to PIA 0.0 0.0 0.0 ns

Input to global clock and clear 0.0 0.0 0.0 ns

Input to fast input register 0.0 0.0 0.0 ns

All outputs 0.0 0.0 0.0 ns

Table 32. EPM7512B Selectable I/O Standard Timing Adder Delays (Part 2 of 2) Note (1)

I/O Standard Parameter Speed Grade Unit

-5 -7 -10

Min Max Min Max Min Max

Altera Corporation 55

MAX 7000B Programmable Logic Device Data Sheet

The ICCINT value depends on the switching frequency and the application

logic. The ICCINT value is calculated with the following equation:

ICCINT =

(A × MCTON) + [B × (MCDEV – MCTON)] + (C × MCUSED × fMAX × togLC)

The parameters in this equation are:

MCTON = Number of macrocells with the Turbo BitTM option turned

on, as reported in the MAX+PLUS II Report File (.rpt)

MCDEV = Number of macrocells in the device

MCUSED = Total number of macrocells in the design, as reported in

the Report File

fMAX = Highest clock frequency to the device

togLC = Average percentage of logic cells toggling at each clock

(typically 12.5%)

A, B, C = Constants, shown in Table 33

This calculation provides an ICC estimate based on typical conditions

using a pattern of a 16-bit, loadable, enabled, up/down counter in each

LAB with no output load. Actual ICC should be verified during operation

because this measurement is sensitive to the actual pattern in the device

and the environmental operating conditions.

Table 33. MAX 7000B ICC Equation Constants

Device A B C

EPM7032B 0.91 0.54 0.010

EPM7064B 0.91 0.54 0.012

EPM7128B 0.91 0.54 0.016

EPM7256B 0.91 0.54 0.017

EPM7512B 0.91 0.54 0.019

56 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Figure 15. ICC vs. Frequency for EPM7032B Devices

Figure 16. ICC vs. Frequency for EPM7064B Devices

100 150 200

250 300

VCC = 2.5 V

Room Temperature

153.8 MHz

285.7 MHz

Frequency (MHz)

Typical ICC

Active (mA)

Low Power

High Speed

EPM7032B

100 150 200

250 300

VCC = 2.5 V

Room Temperature

153.8 MHz

285.7 MHz

Frequency (MHz)

Typical ICC

Active (mA)

Low Power

High Speed

EPM7064B

Altera Corporation 57

MAX 7000B Programmable Logic Device Data Sheet

Figure 17. ICC vs. Frequency for EPM7128B Devices

Figure 18. ICC vs. Frequency for EPM7256B Devices

100 150 200

100

120

140

160

180

200

220

250

VCC = 2.5 V

Room Temperature

129.9 MHz

238.1 MHz

Frequency (MHz)

Typical ICC

Active (mA)

Low Power

High Speed

EPM7128B

100 150

100

150

200

250

300

350

400

200

VCC = 2.5 V

Room Temperature

107.5 MHz

188.7 MHz

Frequency (MHz)

Typical ICC

Active (mA)

Low Power

High Speed

EPM7256B

58 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Figure 19. ICC vs. Frequency for EPM7512B Devices

80 120

100

200

300

400

500

600

700

180

60 100

20 140 160

VCC = 2.5 V

Room Temperature

99.0 MHz

163.9 MHz

Frequency (MHz)

Typical ICC

Active (mA)

Low Power

High Speed

EPM7512B

Altera Corporation 59

MAX 7000B Programmable Logic Device Data Sheet

Device

Pin-Outs

See the Altera web site (http://www.altera.com) or the Altera Digital

Library for pin-out information.

Figures 20 through 29 show the package pin-out diagrams for

MAX 7000B devices.

Figure 20. 44-Pin PLCC/TQFP Package Pin-Out Diagram

Package outlines not drawn to scale.

44-Pin PLCC

I/O

VCC

INPUT/OE2/GCLK2

INPUT/GCLRn

INPUT/OE1

INPUT/GCLK1

GND

I/O

I/O/TDO

I/O

VCC

I/O

I/O/TCK

I/O

GND

I/O

GND

VCC

I/O

6 5 4 3 2 1 44 43 42 41 40

18 19 20 21 22 23 24 25 26 27 28

EPM7032B

EPM7064B

I/O /TDI

I/O

GND

I/O

I/O/TMS

I/O

VCC

I/O

44-Pin TQFP

Pin 12 Pin 23

Pin 34

Pin 1

I/O

VCC

INPUT/OE2/GCLK2

INPUT/GCLRn

INPUT/OE1

INPUT/GCLK1

GND

I/O

I/O/TDO

I/O

VCC

I/O

I/O/TCK

I/O

GND

I/O

GND

VCC

I/O

I/O/TDI

I/O

GND

I/O

I/O/TMS

I/O

VCC

I/O

EPM7032B

EPM7064B

60 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Figure 21. 48-Pin VTQFP Package Pin-Out Diagram

Package outlines not drawn to scale.

Figure 22. 49-Pin Ultra FineLine BGA Package Pin-Out Diagram

Package outline not drawn to scale.

I/O

48-Pin VTQFP

I/O

GND

VCCINT

INPUT/OE2/GCLK2

INPUT/GCLRN

INPUT/OE1

INPUT/GLK1

GNDINT

I/O

N/C

I/O

I/O/TDO

I/O

VCCIO2

I/O

I/O/TCK

I/O / VREFB

GNDIO

I/O

GNDINT

VCCINT

I/O

48 47 46 45 44 43 42 41 40 39 38 37

13 14 15 16 17 18 19 20 21 22 23 24

EPM7032B

EPM7064B

N/C

I/O/TDI

I/O

GNDIO

I/O / VREFA

I/O

I/O/TMS

I/O

VCCIO1

I/O

Indicates

location of

Ball A1

A1 Ball

Pad Corner

7654321

EPM7032B

EPM7064B

EPM7128B

Altera Corporation 61

MAX 7000B Programmable Logic Device Data Sheet

Figure 23. 100-Pin TQFP Package Pin-Out Diagram

Package outline not drawn to scale.

Figure 24. 100-Pin FineLine BGA Package Pin-Out Diagram

Pin 1

Pin 26

Pin 76

Pin 51

EPM7064B

EPM7128B

EPM7256B

Indicates

location of

Ball A1

A1 Ball

Pad Corner

10987 6543 2 1

EPM7064B

EPM7128B

EPM7256B

Package outline not drawn to scale.

62 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Figure 25. 144-Pin TQFP Package Pin-Out Diagram

Package outline not drawn to scale.

Figure 26. 169-Pin Ultra FineLine BGA Pin-Out Diagram

Package outline not drawn to scale.

Indicates location

of Pin 1

Pin 1 Pin 109

Pin 73

Pin 37

EPM7128B

EPM7256B

EPM7512B

Indicates

Location of

Ball A1

A1 Ball

Pad Corner

13121110987654321

EPM7128AE

Altera Corporation 63

MAX 7000B Programmable Logic Device Data Sheet

Figure 27. 208-Pin PQFP Package Pin-Out Diagram

Package outline not drawn to scale.

Pin 1 Pin 157

Pin 105Pin 53

EPM7256B

EPM7512B

64 Altera Corporation

MAX 7000B Programmable Logic Device Data Sheet

Figure 28. 256-Pin BGA Package Pin-Out Diagram

Package outline not drawn to scale.

Indicates

Location of

Ball A1

A1 Ball

Pad Corner

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

EPM7512B

17181920

Altera Corporation 65

MAX 7000B Programmable Logic Device Data Sheet

Figure 29. 256-Pin FineLine BGA Package Pin-Out Diagram

Package outline not drawn to scale.

Revision

History

The information contained in the MAX 7000B Programmable Logic Device

Family Data Sheet version 3.5 supersedes information published in

previous versions.

Version 3.5

The following changes were made to the MAX 7000B Programmable Logic

Device Family Data Sheet version 3.5:

■Updated Figure 28.

Version 3.4

The following changes were made to the MAX 7000B Programmable Logic

Device Family Data Sheet version 3.4:

■Updated text in the “Power Sequencing & Hot-Socketing” section.

Indicates

Location of

Ball A1

A1 Ball

Pad Corner

16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

EPM7128B

EPM7256B

EPM7512B

stylized Altera logo, specific device designations, and all other words and logos that are identified as

trademarks and/or service marks are, unless noted otherwise, the trademarks and service marks of Altera

Corporation in the U.S. and other countries. All other product or service names are the property of their

respective holders. Altera products are protected under numerous U.S. and foreign patents and pending

applications, maskwork rights, and copyrights. Altera warrants performance of its semiconductor products to

current specifications in accordance with Altera's standard warranty, but reserves the right

to make changes to any products and services at any time without notice. Altera assumes no

responsibility or liability arising out of the application or use of any information, product, or

service described herein except as expressly agreed to in writing by Altera Corporation.

Altera customers are advised to obtain the latest version of device specifications before

relying on any published information and before placing orders for products or services.

101 Innovation Drive

San Jose, CA 95134

(408) 544-7000

http://www.altera.com

Applications Hotline:

(800) 800-EPLD

Customer Marketing:

(408) 544-7104

Literature Services:

lit_req@altera.com

MAX 7000B Programmable Logic Device Data Sheet

66 Altera Corporation

Printed on Recycled Paper.

Version 3.3

The following changes were made to the MAX 7000B Programmable Logic

Device Family Data Sheet version 3.3:

■Updated Table 3.

■Added Tables 4 through 6.

Version 3.2

The following changes were made to the MAX 7000B Programmable Logic

Device Family Data Sheet version 3.2:

■Updated Note (10) and added ambient temperature (TA) information

to Table 15.

Version 3.1

The following changes were made to the MAX 7000B Programmable Logic

Device Family Data Sheet version 3.1:

■Updated VIH and VIL specifications in Table 16.

■Updated leakage current conditions in Table 16.

Version 3.0

The following changes were made to the MAX 7000B Programmable Logic

Device Family Data Sheet version 3.0:

■Updated timing numbers in Table 1.

■Updated Table 16.

■Updated timing in Tables 18, 19, 21, 22, 24, 25, 27, 28, 30, and 31.

Literature Licensing

Buy On-Line Download

Entire Site

Your search for EPM7032B found 4 obsolete part numbers.

Results For: EPM7032B

10 part numbers found and 4 obsolete part numbers found

MAX 7000B Device Family (2.5V, SSTL, GTL+)

MAX 7000B Datasheet MAX 7000 Literature

Part Number Format Buying Altera Devices

Part Number Device Pin & Package Temperature Speeds Options

EPM7032BTC44-3

EPM7032BTC44-3N

EPM7032BTC44-5

EPM7032BTC44-5N

EPM7032BTC44-7

EPM7032BTC44-7N

EPM7032B

Pinout

44 pin TQFP Commercial

( 0 to 90°C)

-3, -5, -7 N: Lead-free

EPM7032BTI44-5 EPM7032B

Pinout

44 pin TQFP Industrial

( -40 to 105°C)

-5 None

EPM7032BUC49-3

EPM7032BUC49-5

EPM7032BUC49-7

EPM7032B

Pinout

49 pin UBGA Commercial

( 0 to 90°C)

-3, -5, -7 None

Obsolete Part Numbers

Part Number Format Buying Altera Devices

Part Number Last Order Date Last Ship Date Replacement Notes

EPM7032BLC44-3 06-30-2006 12-30-2006 Call Factory PDN 0510

EPM7032BLC44-5 06-30-2006 12-30-2006 Call Factory PDN 0510

e 1 of 2Altera Part Number Search

20-Dec-2006file://\\bnsndv31\data\

rod\

-user\user\SRI\Alte\EPM7032B.htm

Please Give Us Feedback

EPM7032BLC44-7 06-30-2006 12-30-2006 Call Factory PDN 0510

EPM7032BUC49-3A 12-21-2006 06-30-2007 Call Factory PDN 0518

EPM7032B Search

Advanced Search

e 2 of 2Altera Part Number Search

20-Dec-2006file://\\bnsndv31\data\

rod\

-user\user\SRI\Alte\EPM7032B.htm

Literature Licensing

Buy On-Line Download

Entire Site

Your search for EPM7064B found 6 obsolete part numbers.

Results For: EPM7064B

13 part numbers found and 6 obsolete part numbers found

MAX 7000B Device Family (2.5V, SSTL, GTL+)

MAX 7000B Datasheet MAX 7000 Literature

Part Number Format Buying Altera Devices

Part Number Device Pin & Package Temperature Speeds Options

EPM7064BFC100-3

EPM7064BFC100-5

EPM7064BFC100-7

EPM7064B

Pinout

100 pin FBGA Commercial

( 0 to 90°C)

-3, -5, -7 None

EPM7064BTC44-3

EPM7064BTC44-5

EPM7064BTC44-7

EPM7064BTC44-7N

EPM7064B

Pinout

44 pin TQFP Commercial

( 0 to 90°C)

-3, -5, -7 N: Lead-free

EPM7064BTC100-3

EPM7064BTC100-3N

EPM7064BTC100-5

EPM7064BTC100-5N

EPM7064BTC100-7

EPM7064B

Pinout

100 pin TQFP Commercial

( 0 to 90°C)

-3, -5, -7 N: Lead-free

EPM7064BTI44-5 EPM7064B

Pinout

44 pin TQFP Industrial

( -40 to 105°C)

-5 None

Obsolete Part Numbers

Part Number Format Buying Altera Devices

Part Number Last Order Date Last Ship Date Replacement Notes

e 1 of 2Altera Part Number Search

20-Dec-2006file://\\bnsndv31\data\

rod\

-user\user\SRI\Alte\EPM7064B.htm

Please Give Us Feedback

EPM7064BTI100-5 06-30-2006 12-30-2006 EPM7064BTC100-3 PDN 0510

EPM7064BTI100-7 06-30-2006 12-30-2006 EPM7064BTC100-5 PDN 0510

EPM7064BTI44-7 06-30-2006 12-30-2006 EPM7064BTC44-5 PDN 0510

EPM7064BUC49-3 06-30-2006 12-30-2006 Call Factory PDN 0510

EPM7064BUC49-5 06-30-2006 12-30-2006 Call Factory PDN 0510

EPM7064BUC49-7 06-30-2006 12-30-2006 Call Factory PDN 0510

EPM7064B Search

Advanced Search

e 2 of 2Altera Part Number Search

20-Dec-2006file://\\bnsndv31\data\

rod\

-user\user\SRI\Alte\EPM7064B.htm

Literature Licensing

Buy On-Line Download

Entire Site

Results For: EPM7128B

19 part numbers found and 1 obsolete part number found

MAX 7000B Device Family (2.5V, SSTL, GTL+)

MAX 7000B Datasheet MAX 7000 Literature

Part Number Format Buying Altera Devices

Part Number Device Pin & Package Temperature Speeds Options

EPM7128BFC100-4

EPM7128BFC100-4N

EPM7128BFC100-7

EPM7128BFC100-10

EPM7128BFC100-10N

EPM7128B

Pinout

100 pin FBGA Commercial

( 0 to 90°C)

-4, -7, -10 N: Lead-free

EPM7128BFC256-4

EPM7128BFC256-7

EPM7128BFC256-10

EPM7128B

Pinout

256 pin FBGA Commercial

( 0 to 90°C)

-4, -7, -10 None

EPM7128BFI100-7 EPM7128B

Pinout

100 pin FBGA Industrial

( -40 to 105°C)

-7 None

EPM7128BFI256-7 EPM7128B

Pinout

256 pin FBGA Industrial

( -40 to 105°C)

-7 None

EPM7128BTC100-4

EPM7128BTC100-4N

EPM7128BTC100-7

EPM7128BTC100-7N

EPM7128BTC100-10

EPM7128B

Pinout

100 pin TQFP Commercial

( 0 to 90°C)

-4, -7, -10 N: Lead-free

EPM7128BTC144-4

EPM7128BTC144-7

EPM7128BTC144-10

EPM7128BTC144-10N

EPM7128B

Pinout

144 pin TQFP Commercial

( 0 to 90°C)

-4, -7, -10 N: Lead-free

e 1 of 2Altera Part Number Search

20-Dec-2006file://\\bnsndv31\data\

rod\

-user\user\SRI\Alte\EPM7128B.htm

Please Give Us Feedback

Your search for EPM7128B found 1 obsolete part number.

Obsolete Part Numbers

Part Number Format Buying Altera Devices

Part Number Last Order Date Last Ship Date Replacement Notes

EPM7128BTI100-7 06-30-2006 12-30-2006 EPM7128BTC100-4 PDN 0510

EPM7128B Search

Advanced Search

e 2 of 2Altera Part Number Search

20-Dec-2006file://\\bnsndv31\data\

rod\

-user\user\SRI\Alte\EPM7128B.htm

Literature Licensing

Buy On-Line Download

Entire Site

Results For: EPM7256B

27 part numbers found and 2 obsolete part numbers found

MAX 7000B Device Family (2.5V, SSTL, GTL+)

MAX 7000B Datasheet MAX 7000 Literature

Part Number Format Buying Altera Devices

Part Number Device Pin & Package Temperature Speeds Options

EPM7256BFC256-5

EPM7256BFC256-7

EPM7256BFC256-7N

EPM7256BFC256-10

EPM7256BFC256-10N

EPM7256B

Pinout

256 pin FBGA Commercial

( 0 to 90°C)

-5, -7, -10 N: Lead-free

EPM7256BFI256-7 EPM7256B

Pinout

256 pin FBGA Industrial

( -40 to 105°C)

-7 None

EPM7256BQC208-5

EPM7256BQC208-7

EPM7256BQC208-10

EPM7256B

Pinout

208 pin PQFP Commercial

( 0 to 90°C)

-5, -7, -10 None

EPM7256BTC100-5

EPM7256BTC100-5N

EPM7256BTC100-7

EPM7256BTC100-7N

EPM7256BTC100-10

EPM7256BTC100-10N

EPM7256B

Pinout

100 pin TQFP Commercial

( 0 to 90°C)

-5, -7, -10 N: Lead-free

EPM7256BTC144-5

EPM7256BTC144-5N

EPM7256BTC144-7

EPM7256BTC144-7N

EPM7256BTC144-10

EPM7256BTC144-10N

EPM7256B

Pinout

144 pin TQFP Commercial

( 0 to 90°C)

-5, -7, -10 N: Lead-free

EPM7256BTI100-7N EPM7256B 100 pin TQFP Industrial -7 N: Lead-free

e 1 of 2Altera Part Number Search

20-Dec-2006file://\\bnsndv31\data\

rod\

-user\user\SRI\Alte\EPM7256B.htm

Please Give Us Feedback

Your search for EPM7256B found 2 obsolete part numbers.

Pinout ( -40 to 105°C)

EPM7256BUC169-5

EPM7256BUC169-7

EPM7256BUC169-7N

EPM7256BUC169-10

EPM7256BUC169-10N

EPM7256B

Pinout

169 pin UBGA Commercial

( 0 to 90°C)

-5, -7, -10 N: Lead-free

Obsolete Part Numbers

Part Number Format Buying Altera Devices

Part Number Last Order Date Last Ship Date Replacement Notes

EPM7256BQI208-7 06-30-2006 12-30-2006 EPM7256BQC208-5 PDN 0510

EPM7256BTI100-7 06-30-2006 12-30-2006 EPM7256BTC100-5 PDN 0510

EPM7256B Search

Advanced Search

e 2 of 2Altera Part Number Search

20-Dec-2006file://\\bnsndv31\data\

rod\

-user\user\SRI\Alte\EPM7256B.htm

Literature Licensing

Buy On-Line Download

Entire Site

Your search for EPM7512B found 1 obsolete part number.

Results For: EPM7512B

19 part numbers found and 1 obsolete part number found

MAX 7000B Device Family (2.5V, SSTL, GTL+)

MAX 7000B Datasheet MAX 7000 Literature

Part Number Format Buying Altera Devices

Part Number Device Pin & Package Temperature Speeds Options

EPM7512BBC256-5

EPM7512BBC256-7

EPM7512BBC256-10

EPM7512B

Pinout

256 pin BGA Commercial

( 0 to 90°C)

-5, -7, -10 None

EPM7512BFC256-5

EPM7512BFC256-5N

EPM7512BFC256-7

EPM7512BFC256-7N

EPM7512BFC256-10

EPM7512B

Pinout

256 pin FBGA Commercial

( 0 to 90°C)

-5, -7, -10 N: Lead-free

EPM7512BFI256-7 EPM7512B

Pinout

256 pin FBGA Industrial

( -40 to 105°C)

-7 None

EPM7512BQC208-5

EPM7512BQC208-7

EPM7512BQC208-10

EPM7512B

Pinout

208 pin PQFP Commercial

( 0 to 90°C)

-5, -7, -10 None

EPM7512BTC144-5

EPM7512BTC144-7

EPM7512BTC144-10

EPM7512B

Pinout

144 pin TQFP Commercial

( 0 to 90°C)

-5, -7, -10 None

EPM7512BUC169-5

EPM7512BUC169-7

EPM7512BUC169-7N

EPM7512BUC169-10

EPM7512B

Pinout

169 pin UBGA Commercial

( 0 to 90°C)

-5, -7, -10 N: Lead-free

e 1 of 2Altera Part Number Search

20-Dec-2006file://\\bnsndv31\data\

rod\

-user\user\SRI\Alte\EPM7512B.htm

Please Give Us Feedback

Obsolete Part Numbers

Part Number Format Buying Altera Devices

Part Number Last Order Date Last Ship Date Replacement Notes

EPM7512BFI256-10 06-30-2006 12-30-2006 EPM7512BFC256-7 PDN 0510

EPM7512B Search

Advanced Search

e 2 of 2Altera Part Number Search

20-Dec-2006file://\\bnsndv31\data\

rod\

-user\user\SRI\Alte\EPM7512B.htm