AP1115 0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator General Description Features * * * * * * * AP1115 is a low dropout positive adjustable or fixed-mode regulator with minimum of 0.6A output current capability. The product is specifically designed to provide well-regulated supply for low voltage IC applications such as high-speed bus termination and low current 3.3V logic supply. AP1115 is also well suited for other applications such as VGA cards. AP1115 is guaranteed to have <1.3V dropout at full load current making it ideal to provide well regulated outputs of 1.25V to 5V with up to 18V input supply. 1.3V maximum dropout at full load current Fast transient response Output current limiting Built-in thermal shutdown Packages: SOT89, TO92 Good noise rejection 3-Terminal Adjustable or Fixed 1.5V / 1.8V / 2.5V / 2.8V / 3.0V /3.3V / 5.0V Applications * * PC peripheral Communication Connection Diagram (Top View) AP1115A-3 PIN SOT89 AP1115A-3 PIN TO92 3 Vin 2 Adj (GND) 2 GND 1 Vout 1 Vin 3 Vout Tab is Pin2 AP1115B-3 PIN SOT89 AP1115B-3 PIN TO92 3 Vout 2 Vin 2 Vin 1 Adj (GND) 1 GND 3 Vout Tab is Pin2 Pin Descriptions NAME Adj (GND) I/O Vout O Vin I I FUNCTION A resistor divider from this pin to the Vout pin and ground sets the output voltage. (Ground only for Fixed-Mode) The output of the regulator. A minimum of 10uF capacitor must be connected from this pin to ground to insure stability. The input pin of regulator. Typically a large storage capacitor is connected from this pin to ground to insure that the input voltage does not sag below the minimum dropout voltage during the load transient response. This pin must always be 1.3V higher than Vout in order for the device to regulate properly. This datasheet contains new product information. Anachip Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of this product. No rights under any patent accompany the sale of the product. Rev.1.0 May.19, 2004 1/7 AP1115 0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator Ordering Information AP 1115 X X XX X X Low Dropout Regulator Pin Version Package Lead Free Packing Blank : Tube A: Pin1:Vout Y : SOT89-3L Blank : ADJ Blank : Normal 2:Adj(GND) V : TO92-3L 15 : 1.5V L : Lead Free Package A : Taping 3:Vin B: Pin1:Adj(GND) 2:Vin 3:Vout Vout 18 : 1.8V 25 : 2.5V 28 : 2.8V 30 : 3.0V 33 : 3.3V 50 : 5.0V Typical Circuit 5V 5V C1 100uF C1 100uF Vin Vin GND Adj Vout Vout 3.3V/0.5A R1 121O C2 100uF AP1115A (5V/2.5V Adj output) 5V C1 100uF 5V C1 100uF Vin 2.5V/0.5A C2 100uF AP1115A (5V/3.3V fixed output) Vout VO R2 121O VO 2.5V/0.5A Vout 3.3V/0.5A C2 100uF Vin Adj GND C2 R1 121O 100uF R2 121O AP1115B (5V/2.5V Adj output) AP1115B (5V/3.3V fixed output) Note: Vo = VREF (1+ Anachip Corp. www.anachip.com.tw R2 ) R1 Rev.1.0 May.19, 2004 2/7 AP1115 0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator Absolute Maximum Ratings Symbol VIN PD TST TOP Parameter DC Supply Voltage Power Dissipation Storage Temperature Operating Junction Temperature Range Rating -0.3 to 18 V Internally Limited -65 to +150 0 to +150 Unit V o o C C Electrical Characteristics (Under Operating Conditions) PARAMETER Reference Voltage AP1115-ADJ AP1115-1.5 AP1115-1.8 AP1115-2.5 Output Voltage AP1115-2.8 AP1115-3.0 AP1115-3.3 AP1115-5.0 Line Regulation AP1115-XXX AP1115-ADJ AP1115-1.5 AP1115-1.8 AP1115-2.5 Load Regulation AP1115-2.8 AP1115-3.0 AP1115-3.3 AP1115-5.0 Dropout Voltage (VIN-VOUT) Current Limit Minimum Load Current Thermal Regulation CONDITIONS o TJ=25 C,(VIN-OUT)=1.5V IO=10mA IOUT = 10mA, TJ = 25oC, 3VVIN12V IOUT = 10mA, TJ = 25oC, 3.3VVIN12V o IOUT = 10mA, TJ = 25 C, 4VVIN12V o IOUT = 10mA, TJ = 25 C, 4.3VVIN12V o IOUT = 10mA, TJ = 25 C, 4.5VVIN12V o IOUT = 10mA, TJ = 25 C, 4.8VVIN12V IOUT = 10mA, TJ = 25oC, 6.5VVIN12V IO=10mA,VOUT+1.5V<VIN<15V, o TJ=25 C VIN=3.3V,Vadj=0,0mA<Io<0.6A, o TJ=25 C (Note 1,2) VIN=3V, 0mA<Io<0.6A, o TJ=25 C (Note 1,2) VIN=3.3V, 0mA<Io<0.6A, TJ=25oC (Note 1,2) VIN=4V, 0mA<Io<0.6A, TJ=25oC (Note 1,2) VIN=4.3V, 0mA<Io<0.6A, o TJ=25 C (Note 1,2) VIN =5V, 0IOUT0.6A, o TJ=25 C (Note 1,2) VIN =5V, 0IOUT0.6A, TJ=25oC (Note 1,2) VIN =8V, 0IOUT0.6A, TJ=25oC (Note 1,2) AP1115-ADJ/1.5/1.8 IOUT = 0.6A, VOUT=0.1%VOUT 2.5/2.8/3.0/3.3/5.0 AP1115-ADJ/1.5/1.8 (VIN-VOUT) = 5V 2.5/2.8/3.0/3.3/5.0 0oCTj125oC AP1115-XXX o TA=25 C, 30ms pulse MIN TYP MAX UNIT 1.225 1.250 1.275 V 1.470 1.500 1.530 V 1.764 1.800 1.836 V 2.450 2.500 2.550 V 2.744 2.800 2.856 V 2.940 3.000 3.060 V 3.235 3.300 3.365 V 4.900 5.000 5.100 V - - 0.2 % - - 1 % - 12 15 mV - 15 18 mV - 20 25 mV - 22 28 mV - 23 30 mV - 26 33 mV - 40 50 mV - 1.1 1.3 V 0.7 - - A - 5 0.008 10 0.04 mA %/W This datasheet contains new product information. Anachip Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of this product. No rights under any patent accompany the sale of the product. Rev.1.0 May.19, 2004 3/7 AP1115 0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator Electrical Characteristics (Continued) (Under Operating Conditions) F=120Hz,COUT=25uF Tantalum, IOUT=0.6A AP1115-XXX VIN=VOUT+3V IO=10mA Thermal Resistance Junction-to-Ambient (No heat sink; No air flow) SOT89: Control Circuitry/Power Transistor Thermal Resistance Junction-to-Case Ripple Rejection Temperature Stability JA JC - SOT89 TO92 - 60 0.6 300 160 100 70 - dB % o C/W o C/W Note1: See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18" from the package. Note2: Line and load regulation are guaranteed up to the maximum power dissipation of 5W. Power dissipation is determined by the input/output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. Note3: Quiescent current is defined as the minimum output current required to maintain regulation. At 12V input/output differential the device is guaranteed to regulate if the output current is greater than 10mA. Marking Information Identification Code Date Code Month: A~L Year: 0~9 XX XX X 1 2 3 Output version ADJ 1.5V 1.8V 2.5V 2.8V 3.0V 3.3V 5.0V Identification Code ( See the table ) Blank: normal L: Lead Free Package SOT89-3 Part Number AP1115A AP1115B JO JP JQ JR JC JM JS JT JU JV JW JX JD JN JY JZ (Top View) Part Number: AP1115 A: A version B: B version Output voltage Blank: ADJ 15:1.5V 18:1.8V 25:2.5V 28:2.8V 30:3.0V 33:3.3V 50:5.0V 1115 X XX Y WW X X 1 2 3 Blank: normal L: Lead Free Package Internal code: Blank or A~Z Xth Week: 01~52 Year: "1"=2001 "2"=2002 TO92 Anachip Corp. www.anachip.com.tw Rev.1.0 May.19, 2004 4/7 AP1115 0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator Typical Performance Characteristics 2. 0 0.20 Output Voltage Deviation (%) 1. 8 1. 6 Dropout Voltage (V) 1. 4 1. 2 0 I load=600mA -0.20 Tj = 25 oC 1. 0 -0.40 0. 8 Tj = 125 oC 0. 6 -0.80 0. 4 0. 2 0 0 200 100 300 400 Output Current (mA) 500 -1 600 -25 Dropout Voltage vs Output Current 0 25 50 Temperature ( oC) 75 100 125 Load Regulation vs Temperature 2 1 0.8 1 Output Voltage Deviation (%) Output Voltage Change (%) 1.5 0. 5 0 -0.5 -1 -1.5 -2 -50 -25 0 25 50 Temperature ( oC) 75 100 125 150 0.6 0.4 0.2 0 2 4 7.5 Load Current (A) Output Voltage Deviation (mV) Output Voltage Deviation (mV) Input Voltage (V) Percent Change in Output Voltage vs Temperature Cin=1uF Cout=10uF Tantalum 6.5 5.5 40 20 0 -20 -40 0 20 40 60 80 100 120 140 160 180 200 TIME (us) Line Transient Response 6 8 10 Input Voltage (V) 12 Line Regulation 30 C in = 1uF C out = 10 uF Tantalum Preload = 100mA 20 10 0 -10 -20 2 1 0 -1 0 10 20 30 40 50 TIME (us) 60 70 80 90 100 Load Transient Response Anachip Corp. www.anachip.com.tw Rev.1.0 May.19, 2004 5/7 AP1115 0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator Package Information (1) Package Type: SOT89-3L L HE E D1 e1 e 50(2x) 80(2x) D A c b Symbol A B b1 C D D1 e e1 E HE L b1 b Dimensions In Millimeters Min. 1.40 0.36 0.41 0.35 4.40 1.40 2.90 1.45 2.40 3.94 0.80 Nom. 1.50 0.42 0.47 0.39 4.50 1.60 3.00 1.50 2.50 - Max. 1.60 0.48 0.63 0.43 4.60 1.75 3.10 1.55 2.60 4.25 1.20 Anachip Corp. www.anachip.com.tw Dimensions In Inches Min. 0.055 0.014 0.016 0.014 0.173 0.055 0.114 0.057 0.094 0.155 0.031 Nom. 0.059 0.016 0.043 0.015 0.177 0.062 0.118 0.059 0.098 - Max. 0.063 0.018 0.051 0.017 0.181 0.069 0.122 0.061 0.102 0.167 0.047 Rev.1.0 May.19, 2004 6/7 AP1115 0.6A Low Dropout Positive Adjustable or Fixed-Mode Regulator (2) Package Type: TO92-3L A1 A b b1 b D e E Symbol A A1 b b1 D E L e L Dimensions In Millimeters Min. Nom. Max. 3.302 3.556 3.810 1.016 0.330 0.381 0.432 0.406 0.457 0.506 4.445 4.572 4.699 4.445 4.572 4.699 13.00 15.50 1.150 1.270 1.390 Anachip Corp. www.anachip.com.tw Dimensions In Inches Min. Nom. Max. 0.130 0.140 0.150 0.040 0.013 0.015 0.017 0.016 0.018 0.020 0.175 0.180 0.185 0.175 0.180 0.185 0.512 0.610 0.045 0.050 0.055 Rev.1.0 May.19, 2004 7/7