SST39VF6402B-70-4C-B1KE-T - Microchip Technology

Microchip Technology Company

Not Recommended for New Designs

www.microchip.com

64 Mbit (x16) Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Features

• Organized as 4M x16

• Single Voltage Read and Write Operations

– 2.7-3.6V

• Superior Reliability

– Endurance: 100,000 Cycles (Typical)

– Greater than 100 years Data Retention

• Low Power Consumption (typical values at 5 MHz)

– Active Current: 9 mA (typical)

– Standby Current: 3 µA (typical)

– Auto Low Power Mode: 3 µA (typical)

• Hardware Block-Protection/WP# Input Pin

– Top Block-Protection (top 32 KWord)

for SST39VF6402B

– Bottom Block-Protection (bottom 32 KWord)

for SST39VF6401B

• Sector-Erase Capability

– Uniform 2 KWord sectors

• Block-Erase Capability

– Uniform 32 KWord blocks

• Chip-Erase Capability

• Erase-Suspend/Erase-Resume Capabilities

• Hardware Reset Pin (RST#)

• Security-ID Feature

– SST: 128 bits; User: 128 bits

• Fast Read Access Time:

–70ns

• Latched Address and Data

• Fast Erase and Word-Program:

– Sector-Erase Time: 18 ms (typical)

– Block-Erase Time: 18 ms (typical)

– Chip-Erase Time: 40 ms (typical)

– Word-Program Time: 7 µs (typical)

• Automatic Write Timing

– Internal VPP Generation

• End-of-Write Detection

– Toggle Bits

– Data# Polling

• CMOS I/O Compatibility

• JEDEC Standard

– Flash EEPROM Pin Assignments

– Software command sequence compatibility

- Address format is 11 bits, A10-A0

- Block-Erase 6th Bus Write Cycle is 30H

- Sector-Erase 6th Bus Write Cycle is 50H

• Packages Available

– 48-lead TSOP (12mm x 20mm)

– 48-ball TFBGA (8mm x 10mm)

• All devices are RoHS compliant

The SST39VF6401B / SST39VF6402B devices are 4M x16, CMOS Multi-Purpose

Flash Plus (MPF+) manufactured with SST proprietary, high performance CMOS

SuperFlash technology. The split-gate cell design and thick-oxide tunneling injec-

tor attain better reliability and manufacturability compared with alternate

approaches. The SST39VF6401B / SST39VF6402B write (Program or Erase)

with a 2.7-3.6V power supply. These devices conform to JEDEC standard pinouts

for x16 memories and are command set compatible with other Flash devices,

enabling customers to save time and resources in implementation.

Not recommended for new designs.

Please use SST38VF6401/6402/6403/64040

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Product Description

The SST39VF640xB devices are 4M x16 CMOS Multi-Purpose Flash Plus (MPF+) manufactured with

SST’s proprietary, high-performance CMOS SuperFlash technology. The split-gate cell design and

thick-oxide tunneling injector attain better reliability and manufacturability compared with alternate

approaches. The SST39VF640xB write (Program or Erase) with a 2.7-3.6V power supply. These

devices conform to JEDEC standard pin assignments for x16 memories.

Featuring high performance Word-Program, the SST39VF640xB devices provide a typical Word-Pro-

gram time of 7 µsec. These devices use Toggle Bit or Data# Polling to indicate the completion of Pro-

gram operation. To protect against inadvertent write, they have on-chip hardware and Software Data

Protection schemes. Designed, manufactured, and tested for a wide spectrum of applications, these

devices are offered with a guaranteed typical endurance of 100,000 cycles. Data retention is rated at

greater than 100 years.

The SST39VF640xB devices are suited for applications that require convenient and economical updat-

ing of program, configuration, or data memory. For all system applications, they significantly improve

performance and reliability, while lowering power consumption. They inherently use less energy during

Erase and Program than alternative flash technologies. The total energy consumed is a function of the

applied voltage, current, and time of application. Since for any given voltage range, the SuperFlash

technology uses less current to program and has a shorter erase time, the total energy consumed dur-

ing any Erase or Program operation is less than alternative flash technologies. These devices also

improve flexibility while lowering the cost for program, data, and configuration storage applications.

The SuperFlash technology provides fixed Erase and Program times, independent of the number of

Erase/Program cycles that have occurred. Therefore the system software or hardware does not have

to be modified or de-rated as is necessary with alternative flash technologies, whose Erase and Pro-

gram times increase with accumulated Erase/Program cycles.

To meet high-density, surface mount requirements, the SST39VF640xB devices are offered in 48-lead

TSOP and 48-ball TFBGA packages. See Figures and 2 for pin assignments.

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Block Diagram

Figure 1: Block Diagram

Y-Decoder

I/O Buffers and Data Latches

1288 B1.0

Address Buffer Latches

X-Decoder

DQ15 -DQ

Memory Address

OE#

CE#

WE#

SuperFlash

Memory

Control Logic

WP#

RESET#

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Pin Assignments

Pin Assignments for 48-lead TSOP

Figure 2: pin assignments for 48-ball TFBGA

A15

A14

A13

A12

A11

A10

A19

A20

WE#

RST#

A21

WP#

A18

A17

A16

VSS

DQ15

DQ7

DQ14

DQ6

DQ13

DQ5

DQ12

DQ4

VDD

DQ11

DQ3

DQ10

DQ2

DQ9

DQ1

DQ8

DQ0

OE#

VSS

CE#

1288 48-tsop P1.0

Standard Pinout

Top View

Die Up

1288 4-tfbga B1K P2.0

ABCDEFGH

TOP VIEW (balls facing down)

A13

WE#

A12

RST#

WP#

A17

A14

A10

A21

A18

A15

A11

A19

A20

A16

DQ7

DQ5

DQ2

DQ0

DQ14

DQ12

DQ10

DQ8

CE#

DQ15

DQ13

VDD

DQ11

DQ9

OE#

VSS

DQ6

DQ4

DQ3

DQ1

VSS

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Table 1: Pin Description

Symbol Pin Name Functions

AMS1-A0

1. AMS = Most significant address

AMS =A

21 for SST39VF640xB

Address Inputs To provide memory addresses.

During Sector-Erase AMS-A11 address lines will select the sector.

During Block-Erase AMS-A15 address lines will select the block.

DQ15-DQ0Data Input/output To output data during Read cycles and receive input data during Write cycles.

Data is internally latched during a Write cycle.

The outputs are in tri-state when OE# or CE# is high.

WP# Write Protect To protect the top/bottom boot block from Erase/Program operation when

grounded.

RST# Reset To reset and return the device to Read mode.

CE# Chip Enable To activate the device when CE# is low.

OE# Output Enable To gate the data output buffers.

WE# Write Enable To control the Write operations.

VDD Power Supply To provide power supply voltage: 2.7-3.6V

VSS Ground

NC No Connection Unconnected pins.

T1.0 25008

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Device Operation

Commands are used to initiate the memory operation functions of the device. Commands are written

to the device using standard microprocessor write sequences. A command is written by asserting WE#

low while keeping CE# low. The address bus is latched on the falling edge of WE# or CE#, whichever

occurs last. The data bus is latched on the rising edge of WE# or CE#, whichever occurs first.

The SST39VF640xB also have the Auto Low Power mode which puts the device in a near standby

mode after data has been accessed with a valid Read operation. This reduces the IDD active read cur-

rent from typically 9 mA to typically 3 µA. The Auto Low Power mode reduces the typical IDD active

read current to the range of 2 mA/MHz of Read cycle time. The device exits the Auto Low Power mode

with any address transition or control signal transition used to initiate another Read cycle, with no

access time penalty. Note that the device does not enter Auto-Low Power mode after power-up with

CE# held steadily low, until the first address transition or CE# is driven high.

Read

The Read operation of the SST39VF640xB is controlled by CE# and OE#, both have to be low for the

system to obtain data from the outputs. CE# is used for device selection. When CE# is high, the chip is

deselected and only standby power is consumed. OE# is the output control and is used to gate data

from the output pins. The data bus is in high impedance state when either CE# or OE# is high. Refer to

the Read cycle timing diagram for further details (Figure 3).

Word-Program Operation

The SST39VF640xB are programmed on a word-by-word basis. Before programming, the sector

where the word exists must be fully erased. The Program operation is accomplished in three steps.

The first step is the three-byte load sequence for Software Data Protection. The second step is to load

word address and word data. During the Word-Program operation, the addresses are latched on the

falling edge of either CE# or WE#, whichever occurs last. The data is latched on the rising edge of

either CE# or WE#, whichever occurs first. The third step is the internal Program operation which is ini-

tiated after the rising edge of the fourth WE# or CE#, whichever occurs first. The Program operation,

once initiated, will be completed within 10 µs. See Figures 4 and 5 for WE# and CE# controlled Pro-

gram operation timing diagrams and Figure 19 for flowcharts. During the Program operation, the only

valid reads are Data# Polling and Toggle Bit. During the internal Program operation, the host is free to

perform additional tasks. Any commands issued during the internal Program operation are ignored.

During the command sequence, WP# should be statically held high or low.

Sector/Block-Erase Operation

The Sector- (or Block-) Erase operation allows the system to erase the device on a sector-by-sector (or

block-by-block) basis. The SST39VF640xB offer both Sector-Erase and Block-Erase mode. The sector

architecture is based on uniform sector size of 2 KWord. The Block-Erase mode is based on uniform

block size of 32 KWord. The Sector-Erase operation is initiated by executing a six-byte command

sequence with Sector-Erase command (50H) and sector address (SA) in the last bus cycle. The Block-

Erase operation is initiated by executing a six-byte command sequence with Block-Erase command

(30H) and block address (BA) in the last bus cycle. The sector or block address is latched on the falling

edge of the sixth WE# pulse, while the command (50H or 30H) is latched on the rising edge of the sixth

WE# pulse. The internal Erase operation begins after the sixth WE# pulse. The End-of-Erase opera-

tion can be determined using either Data# Polling or Toggle Bit methods. See Figures 9 and 10 for tim-

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

ing waveforms and Figure 23 for the flowchart. Any commands issued during the Sector- or Block-

Erase operation are ignored. When WP# is low, any attempt to Sector- (Block-) Erase the protected

block will be ignored. During the command sequence, WP# should be statically held high or low.

Erase-Suspend/Erase-Resume Commands

The Erase-Suspend operation temporarily suspends a Sector- or Block-Erase operation thus allowing

data to be read from any memory location, or program data into any sector/block that is not suspended

for an Erase operation. The operation is executed by issuing one byte command sequence with Erase-

Suspend command (B0H). The device automatically enters read mode typically within 20 µs after the

Erase-Suspend command had been issued. Valid data can be read from any sector or block that is not

suspended from an Erase operation. Reading at address location within erase-suspended sectors/

blocks will output DQ2toggling and DQ6at “1”. While in Erase-Suspend mode, a Word-Program oper-

ation is allowed except for the sector or block selected for Erase-Suspend.

To resume Sector-Erase or Block-Erase operation which has been suspended the system must issue

Erase Resume command. The operation is executed by issuing one byte command sequence with

Erase Resume command (30H) at any address in the last Byte sequence.

Chip-Erase Operation

The SST39VF640xB provide a Chip-Erase operation, which allows the user to erase the entire mem-

ory array to the “1” state. This is useful when the entire device must be quickly erased.

The Chip-Erase operation is initiated by executing a six-byte command sequence with Chip-Erase

command (10H) at address 555H in the last byte sequence. The Erase operation begins with the rising

edge of the sixth WE# or CE#, whichever occurs first. During the Erase operation, the only valid read is

Toggle Bit or Data# Polling. See Table 6 for the command sequence, Figure 9 for timing diagram, and

Figure 23 for the flowchart. Any commands issued during the Chip-Erase operation are ignored. When

WP# is low, any attempt to Chip-Erase will be ignored. During the command sequence, WP# should

be statically held high or low.

Write Operation Status Detection

The SST39VF640xB provide two software means to detect the completion of a Write (Program or

Erase) cycle, in order to optimize the system write cycle time. The software detection includes two sta-

tus bits: Data# Polling (DQ7) and Toggle Bit (DQ6). The End-of-Write detection mode is enabled after

the rising edge of WE#, which initiates the internal Program or Erase operation.

The actual completion of the nonvolatile write is asynchronous with the system; therefore, either a

Data# Polling or Toggle Bit read may be simultaneous with the completion of the write cycle. If this

occurs, the system may possibly get an erroneous result, i.e., valid data may appear to conflict with

either DQ7or DQ6. In order to prevent spurious rejection, if an erroneous result occurs, the software

routine should include a loop to read the accessed location an additional two (2) times. If both reads

are valid, then the device has completed the Write cycle, otherwise the rejection is valid.

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Data# Polling (DQ7)

When the SST39VF640xB are in the internal Program operation, any attempt to read DQ7will produce

the complement of the true data. Once the Program operation is completed, DQ7will produce true

data. Note that even though DQ7may have valid data immediately following the completion of an internal Write

operation, the remaining data outputs may still be invalid: valid data on the entire data bus will appear in subse-

quent successive Read cycles after an interval of 1 µs. During internal Erase operation, any attempt to read

DQ7will produce a ‘0’. Once the internal Erase operation is completed, DQ7will produce a ‘1’. The

Data# Polling is valid after the rising edge of fourth WE# (or CE#) pulse for Program operation. For

Sector-, Block- or Chip-Erase, the Data# Polling is valid after the rising edge of sixth WE# (or CE#)

pulse. See Figure 6 for Data# Polling timing diagram and Figure 20 for a flowchart.

Toggle Bits (DQ6 and DQ2)

During the internal Program or Erase operation, any consecutive attempts to read DQ6will produce

alternating “1”s and “0”s, i.e., toggling between 1 and 0. When the internal Program or Erase operation

is completed, the DQ6bit will stop toggling. The device is then ready for the next operation. For Sector-

, Block-, or Chip-Erase, the toggle bit (DQ6) is valid after the rising edge of sixth WE# (or CE#) pulse.

DQ6will be set to “1” if a Read operation is attempted on an Erase-Suspended Sector/Block. If Pro-

gram operation is initiated in a sector/block not selected in Erase-Suspend mode, DQ6will toggle.

An additional Toggle Bit is available on DQ2, which can be used in conjunction with DQ6to check

whether a particular sector is being actively erased or erase-suspended. Table 2 shows detailed status

bits information. The Toggle Bit (DQ2) is valid after the rising edge of the last WE# (or CE#) pulse of

Write operation. See Figure 7 for Toggle Bit timing diagram and Figure 20 for a flowchart.

Note: DQ7and DQ2require a valid address when reading status information.

Table 2: Write Operation Status

Status DQ7DQ6DQ2

Normal Operation Standard Program DQ7# Toggle No Toggle

Standard Erase 0 Toggle Toggle

Erase-Suspend

Mode

Read from Erase-Suspended Sector/Block 1 1 Toggle

Read from Non- Erase-Suspended Sector/Block Data Data Data

Program DQ7# Toggle N/A

T2.0 25008

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Data Protection

The SST39VF640xB provide both hardware and software features to protect nonvolatile data from

inadvertent writes.

Hardware Data Protection

Noise/Glitch Protection: A WE# or CE# pulse of less than 5 ns will not initiate a write cycle.

VDD Power Up/Down Detection: The Write operation is inhibited when VDD is less than 1.5V.

Write Inhibit Mode: Forcing OE# low, CE# high, or WE# high will inhibit the Write operation. This pre-

vents inadvertent writes during power-up or power-down.

Hardware Block Protection

The SST39VF6402B support top hardware block protection, which protects the top 32 KWord block of

the device. The SST39VF6401B support bottom hardware block protection, which protects the bottom

32 KWord block of the device. The Boot Block address ranges are described in Table 3. Program and

Erase operations are prevented on the 32 KWord when WP# is low. If WP# is left floating, it is internally

held high via a pull-up resistor, and the Boot Block is unprotected, enabling Program and Erase opera-

tions on that block.

Table 3: Boot Block Address Ranges

Product Address Range

Bottom Boot Block

SST39VF6401B 000000H-007FFFH

Top Boot Block

SST39VF6402B 3F8000H-3FFFFFH

T3.0 25008

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Hardware Reset (RST#)

The RST# pin provides a hardware method of resetting the device to read array data. When the RST#

pin is held low for at least TRP, any in-progress operation will terminate and return to Read mode. When

no internal Program/Erase operation is in progress, a minimum period of TRHR is required after RST#

is driven high before a valid Read can take place (see Figure 15).

The Erase or Program operation that has been interrupted needs to be reinitiated after the device

resumes normal operation mode to ensure data integrity.

Software Data Protection (SDP)

The SST39VF640xB provide the JEDEC approved Software Data Protection scheme for all data alter-

ation operations, i.e., Program and Erase. Any Program operation requires the inclusion of the three-

byte sequence. The three-byte load sequence is used to initiate the Program operation, providing opti-

mal protection from inadvertent Write operations, e.g., during the system power-up or power-down.

Any Erase operation requires the inclusion of six-byte sequence. These devices are shipped with the

Software Data Protection permanently enabled. See Table 6 for the specific software command codes.

During SDP command sequence, invalid commands will abort the device to read mode within TRC. The

contents of DQ15-DQ8can be VIL or VIH, but no other value, during any SDP command sequence.

Common Flash Memory Interface (CFI)

The SST39VF640xB also contain the CFI information to describe the characteristics of the device. In

order to enter the CFI Query mode, the system must write three-byte sequence, same as product ID

entry command with 98H (CFI Query command) to address 555H in the last byte sequence. Once the

device enters the CFI Query mode, the system can read CFI data at the addresses given in Tables 7

through 9. The system must write the CFI Exit command to return to Read mode from the CFI Query

mode.

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Product Identification

The Product Identification mode identifies the devices as the SST39VF6401B and SST39VF6402B,

and the manufacturer as SST. This mode may be accessed through software operations. Users may

use the Software Product Identification operation to identify the part (i.e., using the device ID) when

using multiple manufacturers in the same socket. For details, see Table 6 for software operation, Figure

11 for the Software ID Entry and Read timing diagram and Figure 21 for the Software ID Entry com-

mand sequence flowchart.

Product Identification Mode Exit/CFI Mode Exit

In order to return to the standard Read mode, the Software Product Identification mode must be exited.

Exit is accomplished by issuing the Software ID Exit command sequence, which returns the device to

the Read mode. This command may also be used to reset the device to the Read mode after any inad-

vertent transient condition that apparently causes the device to behave abnormally, e.g., not read cor-

rectly. Please note that the Software ID Exit/CFI Exit command is ignored during an internal Program

or Erase operation. See Table 6 for software command codes, Figure 13 for timing waveform, and Fig-

ures 21 and 22 for flowcharts.

Table 4: Product Identification

Address Data

Manufacturer’s ID 0000H BFH

Device ID

SST39VF6401B 0001H 236DH

SST39VF6402B 0001H 236CH

T4.0 25008

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Security ID

The SST39VF640xB devices offer a 256-bit Security ID space. The Secure ID space is divided into two

128-bit segments - one factory programmed segment and one user programmed segment. The first

segment is programmed and locked at SST with a random 128-bit number. The user segment is left

un-programmed for the customer to program as desired.

To program the user segment of the Security ID, the user must use the Security ID Word-Program

command. To detect end-of-write for the SEC ID, read the toggle bits. Do not use Data# Polling. Once

this is complete, the Sec ID should be locked using the User Sec ID Program Lock-Out. This disables

any future corruption of this space. Note that regardless of whether or not the Sec ID is locked, neither

Sec ID segment can be erased.

The Secure ID space can be queried by executing a three-byte command sequence with Enter Sec ID

command (88H) at address 555H in the last byte sequence. To exit this mode, the Exit Sec ID com-

mand should be executed. Refer to Table 6 for more details.

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Operations

Table 5: Operation Modes Selection

Mode CE# OE# WE# DQ Address

Read VIL VIL VIH DOUT AIN

Program VIL VIH VIL DIN AIN

Erase VIL VIH VIL X1

1. X can be VIL or VIH, but no other value.

Sector or block address,

XXH for Chip-Erase

Standby VIH X X High Z X

Write Inhibit X VIL X High Z/ DOUT X

XXV

IH High Z/ DOUT X

Product Identification

Software Mode VIL VIL VIH See Table 6

T5.0 25008

Table 6: Software Command Sequence

Command

Sequence

1st Bus

Write Cycle

2nd Bus

Write Cycle

3rd Bus

Write Cycle

4th Bus

Write Cycle

5th Bus

Write Cycle

6th Bus

Write Cycle

Addr1

1. Address format A10-A0(Hex).

Addresses A11-A

21 can be VIL or VIH, but no other value, for Command sequence for SST39VF640xB.

Data2

2. DQ15-DQ8can be VIL or VIH, but no other value, for Command sequence

Addr1Data2Addr1Data2Addr1Data2Addr1Data2Addr1Data2

Word-Program 555H AAH 2AAH 55H 555H A0H WA3

3. WA = Program Word address

Data

Sector-Erase 555H AAH 2AAH 55H 555H 80H 555H AAH 2AAH 55H SAX4

4. SAXfor Sector-Erase; uses AMS-A11 address lines

BAX, for Block-Erase; uses AMS-A15 address lines

AMS = Most significant address

AMS =A

21 for SST39VF640xB

50H

Block-Erase 555H AAH 2AAH 55H 555H 80H 555H AAH 2AAH 55H BAX430H

Chip-Erase 555H AAH 2AAH 55H 555H 80H 555H AAH 2AAH 55H 555H 10H

Erase-Suspend

XXXXH

B0H

Erase-Resume

XXXXH

30H

Query Sec ID5

5. With AMS-A4= 0; Sec ID is read with A3-A0,

SST ID is read with A3= 0 (Address range = 000000H to 000007H),

User ID is read with A3= 1 (Address range = 000010H to 000017H).

Lock Status is read with A7-A0= 0000FFH. Unlocked: DQ3= 1 / Locked: DQ3=0.

555H AAH 2AAH 55H 555H 88H

User Security ID

Word-Program

555H AAH 2AAH 55H 555H A5H WA6

6. Valid Word-Addresses for Sec ID are from 000000H-000007H and 000010H-000017H.

Data

User Security ID

Program Lock-Out

555H AAH 2AAH 55H 555H 85H XXH6

0000H

Software ID Entry7,8 555H AAH 2AAH 55H 555H 90H

CFI Query Entry 555H AAH 2AAH 55H 555H 98H

Software ID Exit9,10

/CFI Exit/Sec ID Exit

555H AAH 2AAH 55H 555H F0H

Software ID Exit9,10

/CFI Exit/Sec ID Exit

XXH F0H

T6.0 25008

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

7. The device does not remain in Software Product ID Mode if powered down.

8. With AMS-A1=0; SST Manufacturer ID = 00BFH, is read with A0=0,

SST39VF6401B Device ID = 236DH, is read with A0=1,

SST39VF6402B Device ID = 236CH, is read with A0=1.

AMS = Most significant address

AMS =A

21 for SST39VF640xB

9. Both Software ID Exit operations are equivalent

10. If users never lock after programming, Sec ID can be programmed over the previously unprogrammed bits (data=1)

using the Sec ID mode again (the programmed “0” bits cannot be reversed to “1”). Valid Word-Addresses for Sec ID are

from 000000H-000007H and 000010H-000017H.

Table 7: CFI Query Identification String1for SST39VF640xB

1. Refer to CFI publication 100 for more details.

Address Data Data

10H 0051H Query Unique ASCII string “QRY”

11H 0052H

12H 0059H

13H 0002H Primary OEM command set

14H 0000H

15H 0000H Address for Primary Extended Table

16H 0000H

17H 0000H Alternate OEM command set (00H = none exists)

18H 0000H

19H 0000H Address for Alternate OEM extended Table (00H = none exits)

1AH 0000H

T7.0 25008

Table 8: System Interface Information for SST39VF640xB

Address Data Data

1BH 0027H VDD Min (Program/Erase)

DQ7-DQ4: Volts, DQ3-DQ0: 100 millivolts

1CH 0036H VDD Max (Program/Erase)

DQ7-DQ4: Volts, DQ3-DQ0: 100 millivolts

1DH 0000H VPP min. (00H = no VPP pin)

1EH 0000H VPP max. (00H = no VPP pin)

1FH 0003H Typical time out for Word-Program 2Nµs (23= 8 µs)

20H 0000H Typical time out for min. size buffer program 2Nµs (00H = not supported)

21H 0004H Typical time out for individual Sector/Block-Erase 2Nms (24=16ms)

22H 0005H Typical time out for Chip-Erase 2Nms (25=32ms)

23H 0001H Maximum time out for Word-Program 2Ntimes typical (21x2

3=16µs)

24H 0000H Maximum time out for buffer program 2Ntimes typical

25H 0001H Maximum time out for individual Sector/Block-Erase 2Ntimes typical (21x2

4=32ms)

26H 0001H Maximum time out for Chip-Erase 2Ntimes typical (21x2

5=64ms)

T8.0 25008

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Table 9: Device Geometry Information for SST39VF640xB

Address Data Data

27H 0017H Device size = 2NBytes (17H = 23; 223 = 8 MByte)

28H 0001H Flash Device Interface description; 0001H = x16-only asynchronous interface

29H 0000H

2AH 0000H Maximum number of bytes in multi-byte write = 2N(00H = not supported)

2BH 0000H

2CH 0002H Number of Erase Sector/Block sizes supported by device

2DH 00FFH Sector Information (y+1=Number of sectors; z x 256B = sector size)

2EH 0007H y = 2047+1=2048 sectors (07FFH = 2047)

2FH 0010H

30H 0000H z = 16 x 256 Bytes = 4 KBytes/sector (0010H = 16)

31H 007FH Block Information (y+1=Number of blocks; z x 256B = block size)

32H 0000H y =127+1=128blocks(007FH = 127)

33H 0000H

34H 0001H z = 256 x 256 Bytes = 64 KBytes/block (0100H = 256)

T9.0 25008

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Absolute Maximum Stress Ratings (Applied conditions greater than those listed under “Absolute

Maximum Stress Ratings” may cause permanent damage to the device. This is a stress rating only and

functional operation of the device at these conditions or conditions greater than those defined in the

operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating con-

ditions may affect device reliability.)

Temperature Under Bias ............................................. -55°C to +125°C

Storage Temperature ................................................ -65°C to +150°C

D. C. Voltage on Any Pin to Ground Potential ............................-0.5V to VDD+0.5V

Transient Voltage (<20 ns) on Any Pin to Ground Potential ..................-2.0V to VDD+2.0V

Voltage on A9Pin to Ground Potential .....................................-0.5V to 13.2V

Package Power Dissipation Capability (TA= 25°C) .................................. 1.0W

Surface Mount Solder Reflow Temperature1...........................260°C for 10 seconds

Output Short Circuit Current2.................................................. 50mA

1. Excluding certain with-Pb 32-PLCC units, all packages are 260°C capable in both non-Pb and with-Pb solder versions.

Certain with-Pb 32-PLCC package types are capable of 240°C for 10 seconds; please consult the factory for the latest

information.

2. Outputs shorted for no more than one second. No more than one output shorted at a time.

Table 10:Operating Range

Range Ambient Temp VDD

Commercial 0°C to +70°C 2.7-3.6V

Industrial -40°C to +85°C 2.7-3.6V

T10.1 25008

Table 11:AC Conditions of Test1

1. See Figures 17 and 18

Input Rise/Fall Time Output Load

5ns CL=30pF

T11.1 25008

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Table 12:DC Operating Characteristics VDD = 2.7-3.6V1

Symbol Parameter

Limits

Test ConditionsMin Max Units

IDD Power Supply Current Address input=VILT/VIHT2,atf=5

MHz, VDD=VDD Max

Read318 mA CE#=VIL, OE#=WE#=VIH, all I/Os open

Program and Erase 35 mA CE#=WE#=VIL, OE#=VIH

ISB Standby VDD Current 20 µA CE#=VIHC,V

DD=VDD Max

IALP Auto Low Power 20 µA CE#=VILC,V

DD=VDD Max

All inputs=VSS or VDD, WE#=VIHC

ILI Input Leakage Current 1 µA VIN=GND to VDD,V

DD=VDD Max

ILIW Input Leakage Current

on WP# pin and RST#

10 µA WP#=GND to VDD or RST#=GND to

VDD

ILO Output Leakage Current 10 µA VOUT=GND to VDD,V

DD=VDD Max

VIL Input Low Voltage 0.8 V VDD=VDD Min

VILC Input Low Voltage (CMOS) 0.3 V VDD=VDD Max

VIH Input High Voltage 0.7VDD VV

DD=VDD Max

VIHC Input High Voltage (CMOS) VDD-0.3 V VDD=VDD Max

VOL Output Low Voltage 0.2 V IOL=100 µA, VDD=VDD Min

VOH Output High Voltage VDD-0.2 V IOH=-100 µA, VDD=VDD Min

T12.0 25008

1. Typical conditions for the Active Current shown on the front page of the data sheet are average values at 25°C

(room temperature), and VDD = 3V. Not 100% tested.

2. See Figure 17

3. The IDD current listed is typically less than 2mA/MHz, with OE# at VIH. Typical VDD is 3V.

Table 13:Recommended System Power-up Timings

Symbol Parameter Minimum Units

TPU-READ1

1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.

Power-up to Read Operation 100 µs

TPU-WRITE1Power-up to Program/Erase Operation 100 µs

T13.0 25008

Table 14:Capacitance (TA= 25°C, f=1 Mhz, other pins open)

Parameter Description Test Condition Maximum

CI/O1

1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.

I/O Pin Capacitance VI/O =0V 12pF

CIN1Input Capacitance VIN =0V 6pF

T14.0 25008

Table 15:Reliability Characteristics

Symbol Parameter Minimum Specification Units Test Method

NEND1,2

1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.

2. NEND endurance rating is qualified as a 10,000 cycle minimum for the whole device. A sector- or block-level rating would

result in a higher minimum specification.

Endurance 10,000 Cycles JEDEC Standard A117

TDR1Data Retention 100 Years JEDEC Standard A103

ILTH1Latch Up 100 + IDD mA JEDEC Standard 78

T15.0 25008

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

AC Characteristics

Table 16:Read Cycle Timing Parameters VDD = 2.7-3.6V

Symbol Parameter

SST39VF640xB-70

UnitsMin Max

TRC Read Cycle Time 70 ns

TCE Chip Enable Access Time 70 ns

TAA Address Access Time 70 ns

TOE Output Enable Access Time 35 ns

TCLZ1

1. This parameter is measured only for initial qualification and after a design or process change that could affect this

parameter.

CE# Low to Active Output 0 ns

TOLZ1OE# Low to Active Output 0 ns

TCHZ1CE# High to High-Z Output 20 ns

TOHZ1OE# High to High-Z Output 20 ns

TOH1Output Hold from Address Change 0 ns

TRP1RST# Pulse Width 500 ns

TRHR1RST# High before Read 50 ns

TRY1,2

2. This parameter applies to Sector-Erase, Block-Erase, and Program operations.

This parameter does not apply to Chip-Erase operations.

RST# Pin Low to Read Mode 20 µs

T16.0 25008

Table 17:Program/Erase Cycle Timing Parameters

Symbol Parameter Min Max Units

TBP Word-Program Time 10 µs

TAS Address Setup Time 0 ns

TAH Address Hold Time 30 ns

TCS WE# and CE# Setup Time 0 ns

TCH WE# and CE# Hold Time 0 ns

TOES OE# High Setup Time 0 ns

TOEH OE# High Hold Time 10 ns

TCP CE# Pulse Width 40 ns

TWP WE# Pulse Width 40 ns

TWPH1

1. This parameter is measured only for initial qualification and after a design or process change that could affect this

parameter.

WE# Pulse Width High 30 ns

TCPH1CE# Pulse Width High 30 ns

TDS Data Setup Time 30 ns

TDH1Data Hold Time 0 ns

TIDA1Software ID Access and Exit Time 150 ns

TSE Sector-Erase 25 ms

TBE Block-Erase 25 ms

TSCE Chip-Erase 50 ms

T17.0 25008

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 3: Read Cycle Timing Diagram

Figure 4: WE# Controlled Program Cycle Timing Diagram

1288 F03.0

ADDRESS AMS-0

DQ15-0

WE#

OE#

CE#

TCE

TRC TAA

TOE

TOLZ

VIH

HIGH-Z

TCLZ TOH TCHZ

HIGH-Z

DATA VALIDDATA VALID

TOHZ

Note: AMS = Most significant address

AMS =A

21 for SST39VF640xB

1288 F04.0

ADDRESS AMS-0

DQ15-0

TDH

TWPH

TDS

TWP

TAH

TAS

TCH

TCS

CE#

SW0 SW1 SW2

555 2AA 555 ADDR

XXAA XX55 XXA0 DATA

INTERNAL PROGRAM OPERATION STARTS

WORD

(ADDR/DATA)

OE#

WE#

TBP

Note: AMS = Most significant address

AMS =A

21 for SST39VF640xB

WP# must be held in proper logic state (VIL or VIH) 1 µs prior to and 1 µs after the command sequence.

X can be VIL or VIH, but no other value.

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 5: CE# Controlled Program Cycle Timing Diagram

Figure 6: Data# Polling Timing Diagram

1288 F05.0

ADDRESS AMS-0

DQ15-0

TDH

TCPH TDS

TCP

TAH

TAS

TCH

TCS

WE#

SW0 SW1 SW2

555 2AA 555 ADDR

XXAA XX55 XXA0 DATA

INTERNAL PROGRAM OPERATION STARTS

WORD

(ADDR/DATA)

OE#

CE#

TBP

Note: AMS = Most significant address

AMS =A

21 for SST39VF640xB

WP# must be held in proper logic state (VIL or VIH) 1 µs prior to and 1 µs after the command sequence.

X can be VIL or VIH, but no other value.

1288 F06.0

ADDRESS AMS-0

DQ7DATA DATA # DATA # D ATA

WE#

OE#

CE#

TOEH

TOE

TCE

TOES

Note: AMS = Most significant address

AMS =A

21 for SST39VF640xB

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 7: Toggle Bits Timing Diagram

Figure 8: WE# Controlled Chip-Erase Timing Diagram

1288 F07.0

ADDRESS AMS-0

DQ6and DQ2

WE#

OE#

CE#

TOE

TOEH

TCE

TOES

TWO READ CYCLES

WITH SAME OUTPUTS

Note: AMS = Most significant address

AMS =A

21 for SST39VF640xB

1288 F08.0

ADDRESS AMS-0

DQ15-0

WE#

SW0 SW1 SW2 SW3 SW4 SW5

555 2AA 2AA555 555

XX55 XX10XX55XXAA XX80 XXAA

555

OE#

CE#

SIX-BYTE CODE FOR CHIP-ERASE

TSCE

TWP

Note: This device also supports CE# controlled Chip-Erase operation The WE# and CE# signals are

interchangeable as long as minimum timings are met. (See Table 17)

AMS = Most significant address

AMS =A

21 for SST39VF640xB

WP# must be held in proper logic state (VIL or VIH) 1 µs prior to and 1 µs after the command sequence.

X can be VIL or VIH, but no other value.

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 9: WE# Controlled Block-Erase Timing Diagram

1288 F09.0

ADDRESS AMS-0

DQ15-0

WE#

SW0 SW1 SW2 SW3 SW4 SW5

555 2AA 2AA555 555

XX55 XX30XX55XXAA XX80 XXAA

BAX

OE#

CE#

SIX-BYTE CODE FOR BLOCK-ERASE

TBE

TWP

Note: This device also supports CE# controlled Block-Erase operation The WE# and CE# signals are

interchangeable as long as minimum timings are met. (See Table 17)

BAX= Block Address

AMS = Most significant address

AMS =A

21 for SST39VF640xB

WP# must be held in proper logic state (VIL or VIH) 1 µs prior to and 1 µs after the command sequence.

X can be VIL or VIH, but no other value.

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 10:WE# Controlled Sector-Erase Timing Diagram

1288 F10.0

ADDRESS AMS-0

DQ15-0

WE#

SW0 SW1 SW2 SW3 SW4 SW5

555 2AA 2AA555 555

XX55 XX50XX55XXAA XX80 XXAA

SAX

OE#

CE#

SIX-BYTE CODE FOR SECTOR-ERASE

TSE

TWP

Note: This device also supports CE# controlled Sector-Erase operation The WE# and CE# signals are

interchangeable as long as minimum timings are met. (See Table 17)

SAX= Sector Address

AMS = Most significant address

AMS =A

21 for SST39VF640xB

WP# must be held in proper logic state (VIL or VIH) 1 µs prior to and 1 µs after the command sequence.

X can be VIL or VIH, but no other value.

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 11:Software ID Entry and Read

Figure 12:CFI Query Entry and Read

1288 F11.0

ADDRESS A14-0

TIDA

DQ15-0

WE#

SW0 SW1 SW2

555 2AA 555 0000 0001

OE#

CE#

Three-Byte Sequence for Software ID Entry

TWP

TWPH TAA

00BF Device IDXX55XXAA XX90

Note: Device ID = 236DH for SST39VF6401B and 236CH for SST39VF6402B

WP# must be held in proper logic state (VIL or VIH) 1 µs prior to and 1 µs after the command sequence.

X can be VIL or VIH, but no other value.

1288 F12.0

ADDRESS A14-0

TIDA

DQ15-0

WE#

SW0 SW1 SW2

555 2AA 555

OE#

CE#

Three-Byte Sequence for CFI Query Entry

TWP

TWPH TAA

XX55XXAA XX98

Note: WP# must be held in proper logic state (VIL or VIH) 1 µs prior to and 1 µs after the command sequence.

X can be VIL or VIH, but no other value.

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 13:Software ID Exit/CFI Exit

Figure 14:Sec ID Entry

1288 F13.0

ADDRESS A14-0

DQ15-0

TIDA

TWP

TWHP

WE#

SW0 SW1 SW2

555 2AA 555

THREE-BYTE SEQUENCE FOR

SOFTWARE ID EXIT AND RESET

OE#

CE#

XXAA XX55 XXF0

Note: WP# must be held in proper logic state (VIL or VIH) 1 µs prior to and 1 µs after the command sequence.

X can be VIL or VIH, but no other value.

1288 F14.0

ADDRESS A

MS-0

IDA

15-0

WE#

SW0 SW1 SW2

555 2AA 555

OE#

CE#

THREE-BYTE SEQUENCE FOR

CFI QUERY ENTRY

WPH

XX55XXAA XX88

Note: AMS = Most significant address

AMS =A

21 for SST39VF640xB

WP# must be held in proper logic state (VIL or VIH) 1 µs prior to and 1 µs after the command sequence.

X can be VIL or VIH, but no other value.

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 15:RST# Timing Diagram (When no internal operation is in progress)

Figure 16:RST# Timing Diagram (During Program or Erase operation)

1288 F15.0

RST#

CE#/OE#

TRP

TRHR

1288 F16.0

RST#

CE#/OE#

TRP

TRY

End-of-Write Detection

(Toggle-Bit)

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 17:AC Input/Output Reference Waveforms

Figure 18:A Test Load Example

1288 F17.0

REFERENCE POINTS OUTPUTINPUT VIT

VIHT

VILT

VOT

AC test inputs are driven at VIHT (0.9 VDD) for a logic “1” and VILT (0.1 VDD) for a logic

“0”. Measurement reference points for inputs and outputs are VIT (0.5 VDD) and VOT (0.5

VDD). Input rise and fall times (10% 90%) are <5 ns.

Note: VIT -V

INPUT Test

VOT -V

OUTPUT Test

VIHT -V

INPUT HIGH Test

VILT -V

INPUT LOW Test

1288 F18.0

TO TESTER

TO DUT

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 19:Word-Program Algorithm

1288 F19.0

Start

Load data: XXAAH

Address: 555H

Load data: XX55H

Address: 2AAH

Load data: XXA0H

Address: 555H

Load Word

Address/Word

Data

Wait for end of

Program (TBP,

Data# Polling

bit, or Toggle bit

operation)

Program

Completed

X can be VIL or VIH, but no other value

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 20:Wait Options

1288 F20.0

Wait TBP,

TSCE, TSE

or TBE

Program/Erase

Initiated

Internal Timer Toggle Bit

Ye s

Program/Erase

Completed

Does DQ6

match

Read same

word

Data# Polling

Program/Erase

Completed

Program/Erase

Completed

Read word

Is DQ7=

true data

Read DQ7

Program/Erase

Initiated

Program/Erase

Initiated

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 21:Software ID/CFI Entry Command Flowcharts

1288 F21.0

Load data: XXAAH

Address: 555H

Software Product ID Entry

Command Sequence

Load data: XX55H

Address: 2AAH

Load data: XX90H

Address: 555H

Wait TIDA

Read Software ID

Load data: XXAAH

Address: 555H

CFI Query Entry

Command Sequence

Load data: XX55H

Address: 2AAH

Load data: XX98H

Address: 555H

Wait TIDA

Read CFI data

Load data: XXAAH

Address: 555H

Sec ID Query Entry

Command Sequence

Load data: XX55H

Address: 2AAH

Load data: XX88H

Address: 555H

Wait TIDA

Read Sec ID

X can be VIL or VIH, but no other value

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 22:Software ID/CFI Exit Command Flowcharts

1288 F22.0

Load data: XXAAH

Address: 555H

Software ID Exit/CFI Exit/Sec ID Exit

Command Sequence

Load data: XX55H

Address: 2AAH

Load data: XXF0H

Address: 555H

Load data: XXF0H

Address: XXH

Return to normal

operation

Wait TIDA

Return to normal

operation

X can be VIL or VIH, but no other value

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 23:Erase Command Sequence

1288 F23.0

Load data: XXAAH

Address: 555H

Chip-Erase

Command Sequence

Load data: XX55H

Address: 2AAH

Load data: XX80H

Address: 555H

Load data: XX55H

Address: 2AAH

Load data: XX10H

Address: 555H

Load data: XXAAH

Address: 555H

Wait TSCE

Chip erased

to FFFFH

Load data: XXAAH

Address: 555H

Sector-Erase

Command Sequence

Load data: XX55H

Address: 2AAH

Load data: XX80H

Address: 555H

Load data: XX55H

Address: 2AAH

Load data: XX50H

Address: SAX

Load data: XXAAH

Address: 555H

Wait TSE

Sector erased

to FFFFH

Load data: XXAAH

Address: 555H

Block-Erase

Command Sequence

Load data: XX55H

Address: 2AAH

Load data: XX80H

Address: 555H

Load data: XX55H

Address: 2AAH

Load data: XX30H

Address: BAX

Load data: XXAAH

Address: 555H

Wait TBE

Block erased

to FFFFH

X can be VIL or VIH, but no other value

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Product Ordering Information

Valid Combinations for SST39VF6401B

SST39VF6401B-70-4C-EKE SST39VF6401B-70-4C-B1KE

SST39VF6401B-70-4I-EKE SST39VF6401B-70-4I-B1KE

Valid Combinations for SST39VF6402B

SST39VF6402B-70-4C-EKE SST39VF6402B-70-4C-B1KE

SST39VF6402B-70-4I-EKE SST39VF6402B-70-4I-B1KE

Note:Valid combinations are those products in mass production or will be in mass production. Consult your SST

sales representative to confirm availability of valid combinations and to determine availability of new combi-

nations.

SST 39 VF 6401B - 70 - 4I - QAE

XX XX XXXXX - XX - XX -XXX

Environmental Attribute

E1= non-Pb

Package Modifier

K = 48 balls or leads

Package Type

E = TSOP (type1, die up, 12mm x 20mm)

B1 = TFBGA (8mm x 10mm, 0.8mm pitch)

Temperature Range

C = Commercial = 0°C to +70°C

I = Industrial = -40°C to +85°C

Minimum Endurance

4 = 10,000 cycles

Read Access Speed

70=70ns

Hardware Block Protection

1 = Bottom Boot-Block

2 = Top Boot-Block

Device Density

640 = 64 Mbit

Voltage

V = 2.7-3.6V

Product Series

39 = Multi-Purpose Flash Plus

1. Environmental suffix “E” denotes non-Pb solder.

SST non-Pb solder devices are “RoHS Compliant”.

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Packaging Diagrams

Figure 24:48-lead Thin Small Outline Package (TSOP) 12mm x 20mm

SST Package Code: EK

1.05

0.95

0.70

0.50

18.50

18.30

20.20

19.80

0.70

0.50

12.20

11.80

0.27

0.17

0.15

0.05

48-tsop-EK-8

Note: 1. Complies with JEDEC publication 95 MO-142 DD dimensions,

although some dimensions may be more stringent.

2. All linear dimensions are in millimeters (max/min).

3. Coplanarity: 0.1 mm

4. Maximum allowable mold flash is 0.15 mm at the package ends, and 0.25 mm between leads.

1.20

max.

1mm

0°- 5°

DETAIL

Pin # 1 Identifier

0.50

BSC

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Figure 25:48-ball Thin-profile, Fine-pitch Ball Grid Array (TFBGA) 8mm x 10mm

SST Package Code: B1K

A1 CORNER

BOTTOM VIEWTOP VIEW

8.00 ± 0.10

A1 CORNER

10.00 ± 0.10

HGFEDCBA

ABCDEFGH

0.45 ± 0.05

(48X)

0.80

4.00

0.80

5.60

48-tfbga-B1K-8x10-450mic-5

Note: 1. Although many dimensions are similar to those of JEDEC Publication 95, MO-210, this specific package is not registered.

2. All linear dimensions are in millimeters.

3. Coplanarity: 0.12 mm

4. Ball opening size is 0.38 mm ( 0.05 mm)

1mm

SIDE VIEW

SEATING PLANE

0.35 ± 0.05

1.10 ± 0.10

0.12

64 Mbit Multi-Purpose Flash Plus

SST39VF6401B / SST39VF6402B

Not Recommended for New Designs

Microchip Technology Company

Table 18:Revision History

Revision Description Date

00 •Initial release Mar 2005

01 •Clarified JEDEC software command compatibility on page 1 May 2005

02 •Changed document phase from Preliminary Information to Data Sheet Jul 2006

A•Removed Pb and 90ns parts

•Marked the document “Not Recommended for New Designs”

•Applied new document format

•Released document under letter revision system

•Updated Spec number from S71288 to DS25008

Aug 2011

SST, Silicon Storage Technology, the SST logo, SuperFlash, MTP, and FlashFlex are registered trademarks of Silicon Storage Tech-

nology, Inc. MPF, SQI, Serial Quad I/O, and Z-Scale are trademarks of Silicon Storage Technology, Inc. All other trademarks and

registered trademarks mentioned herein are the property of their respective owners.

Specifications are subject to change without notice. Refer to www.microchip.com for the most recent documentation. For the most current

package drawings, please see the Packaging Specification located at http://www.microchip.com/packaging.

Memory sizes denote raw storage capacity; actual usable capacity may be less.

SST makes no warranty for the use of its products other than those expressly contained in the Standard Terms and Conditions of

Sale.

For sales office locations and information, please see www.microchip.com.

Silicon Storage Technology, Inc.

A Microchip Technology Company

www.microchip.com

ISBN:978-1-61341-547-4