Si5325 P R E L I M I N A R Y D A TA S H E E T P-P R O G R A M M A B L E P R E C I S I O N C L O C K M U L T I P L I E R Description Features Generates any frequency from 10 to 945 MHz and select frequencies to 1.4 GHz from an input frequency of 10 to 710 MHz Low jitter clock outputs w/jitter generation as low as 0.6 ps rms (30 kHz-1.3 MHz) Integrated loop filter with selectable loop bandwidth (150 kHz to 2 MHz) Dual clock inputs w/manual or automatically controlled hitless switching Dual clock outputs with selectable signal format (LVPECL, LVDS, CML, CMOS) Support for ITU G.709 and custom FEC ratios (255/238, 255/237, 255/236) LOS, FOS alarm outputs Digitally-controlled output phase adjust The Si5325 is a low jitter, precision clock multiplier for applications requiring clock multiplication without jitter attenuation. The Si5325 accepts dual clock inputs ranging from 10 to 710 MHz and generates two clock outputs ranging from 10 to 945 MHz and select frequencies to 1.4 GHz. The two outputs are divided down separately from a common source. The device provides virtually any frequency translation combination across this operating range. The Si5325 input clock frequency and clock multiplication ratio are programmable through an I2C or SPI interface. The Si5325 is based on Silicon Laboratories' 3rd-generation DSPLL(R) technology, which provides any-rate frequency synthesis in a highly integrated PLL solution that eliminates the need for external VCXO and loop filter components. The DSPLL loop bandwidth is digitally programmable, providing jitter performance optimization at the application level. Operating from a single 1.8, 2.5, or 3.3 V supply, the Si5325 is ideal for providing clock multiplication in high performance timing applications. I2C or SPI programmable On-chip voltage regulator for 1.8, 2.5, or 3.3 V 10% operation Small size: 6 x 6 mm 36-lead QFN Pb-free, ROHS compliant Applications SONET/SDH OC-48/OC-192 line cards GbE/10GbE, 1/2/4/8/10GFC line cards ITU G.709 and custom FEC line cards Optical modules Wireless basestations Data converter clocking xDSL SONET/SDH + PDH clock synthesis Test and measurement CKIN1 CKIN2 / N31 / NC1 CKOUT1 / NC2 CKOUT2 (R) / N32 DSPLL / N2 Alarms VDD (1.8, 2.5, or 3.3 V) Control Signal Detect I2C/SPI Port GND Clock Select Device Interrupt Preliminary Rev. 0.26 7/07 Copyright (c) 2007 by Silicon Laboratories Si5325 This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Si5325 Table 1. Performance Specifications (VDD = 1.8, 2.5, or 3.3 V 10%, TA = -40 to 85 C) Parameter Symbol Temperature Range Supply Voltage Supply Current Input Clock Frequency (CKIN1, CKIN2) Output Clock Frequency (CKOUT1, CKOUT2) Min Typ Max Unit TA -40 25 85 C VDD 2.97 3.3 3.63 V 2.25 2.5 2.75 V 1.62 1.8 1.98 V fOUT = 622.08 MHz Both CKOUTs enabled LVPECL format output -- 251 279 mA CKOUT2 disabled -- 217 243 mA fOUT = 19.44 MHz Both CKOUTs enabled CMOS format output -- 204 234 mA CKOUT2 disabled -- 194 220 mA Tristate/Sleep Mode -- TBD TBD mA Input frequency and clock multiplication ratio determined by programming device PLL dividers. Consult Silicon Laboratories configuration software DSPLLsim at www.silabs.com/timing to determine PLL divider settings for a given input frequency/clock multiplication ratio combination. 10 -- 710 MHz 10 970 1213 -- -- -- 945 1134 1417 MHz 0.25 -- 1.9 VPP 1.8 V 10% 0.9 -- 1.4 V 2.5 V 10% 1.0 -- 1.7 V 3.3 V 10% 1.1 -- 1.95 V -- 11 ns 40 -- 60 % 50 -- -- ns VDD - 1.42 -- VDD - 1.25 V 1.1 -- 1.9 V 0.5 -- 0.93 V IDD CKF CKOF Test Condition Input Clocks (CKIN1, CKIN2) Differential Voltage Swing CKNDPP Common Mode Voltage CKNVCM Rise/Fall Time CKNTRF 20-80% Duty Cycle CKNDC Whichever is less Output Clocks (CKOUT1, CKOUT2) Common Mode VOCM Differential Output Swing VOD Single Ended Output Swing VSE LVPECL 100 load line-to-line Note: For a more comprehensive listing of device specifications, please consult the Silicon Laboratories Any-Rate Precision Clock Family Reference Manual. This document can be downloaded from www.silabs.com/timing. 2 Preliminary Rev. 0.26 Si5325 Table 1. Performance Specifications (Continued) (VDD = 1.8, 2.5, or 3.3 V 10%, TA = -40 to 85 C) Parameter Symbol Test Condition Min Typ Max Unit Rise/Fall Time CKOTRF 20-80% -- 230 350 ps Duty Cycle CKODC 45 -- 55 % fOUT = 622.08 MHz, LVPECL output format 50 kHz-80 MHz -- 0.6 TBD ps rms 12 kHz-20 MHz -- 0.6 TBD ps rms 800 Hz-80 MHz -- TBD TBD ps rms -- 0.05 0.1 dB fOUT = 622.08 MHz 100 Hz offset -- TBD TBD dBc/Hz 1 kHz offset -- TBD TBD dBc/Hz 10 kHz offset -- TBD TBD dBc/Hz 100 kHz offset -- TBD TBD dBc/Hz 1 MHz offset -- TBD TBD dBc/Hz PLL Performance Jitter Generation JGEN Jitter Transfer JPK Phase Noise CKOPN Subharmonic Noise SPSUBH Phase Noise @ 100 kHz Offset -- TBD TBD dBc Spurious Noise SPSPUR Max spur @ n x F3 (n > 1, n x F3 < 100 MHz) -- TBD TBD dBc JA Still Air -- 38 -- C/W Package Thermal Resistance Junction to Ambient Note: For a more comprehensive listing of device specifications, please consult the Silicon Laboratories Any-Rate Precision Clock Family Reference Manual. This document can be downloaded from www.silabs.com/timing. Table 2. Absolute Maximum Ratings Parameter Symbol Value Unit DC Supply Voltage VDD -0.5 to 3.6 V LVCMOS Input Voltage VDIG -0.3 to (VDD + 0.3) V Operating Junction Temperature TJCT -55 to 150 C Storage Temperature Range TSTG -55 to 150 C 2 kV 200 V ESD HBM Tolerance (100 pF, 1.5 k) ESD MM Tolerance Latch-Up Tolerance JESD78 Compliant Note: Permanent device damage may occur if the Absolute Maximum Ratings are exceeded. Functional operation should be restricted to the conditions as specified in the operation sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods of time may affect device reliability. Preliminary Rev. 0.26 3 Si5325 C4 1 F System Power Supply C3 0.1 F Ferrite Bead C2 0.1 F VDD = 3.3 V VDD 130 CKIN1+ GND 130 C1 0.1 F CKOUT1+ 0.1 F + 100 CKOUT1- CKIN1- 82 - Clock Outputs CKOUT2+ Input Clock Sources* 0.1 F 82 CKOUT2- 0.1 F - 130 CKIN2+ Si5325 CKIN2- 82 + 100 VDD = 3.3 V 130 0.1 F INT_C1B 82 Interrupt/CKIN_1 Invalid Indicator C2B CMODE Control Mode (L) A[2:0] RST Reset CKIN_2 Invalid Indicator Serial Port Address SDA Serial Data SCL Serial Clock I2C Interface *Note: Assumes differential LVPECL termination (3.3 V) on clock inputs. Figure 1. Si5325 Typical Application Circuit (I2C Control Mode) C4 1 F System Power Supply C3 0.1 F Ferrite Bead C2 0.1 F VDD = 3.3 V CKIN1+ GND 130 VDD 130 C1 0.1 F CKOUT1- Reset 0.1 F + 0.1 F - 130 CKIN2- Control Mode (H) - 100 CKOUT2- CKIN2+ 82 0.1 F Clock Outputs VDD = 3.3 V 130 + 82 CKOUT2+ Input Clock Sources* 0.1 F 100 CKIN1- 82 CKOUT1+ Si5325 INT_C1B C2B Interrupt/CLKIN_1 Invalid Indicator CLKIN_2 Invalid Indicator 82 CMODE RST SS SDO SDI SCLK Slave Select Serial Data Out SPI Interface Serial Data In Serial Clock *Note: Assumes differential LVPECL termination (3.3 V) on clock inputs. Figure 2. Si5325 Typical Application Circuit (SPI Control Mode) 4 Preliminary Rev. 0.26 Si5325 1. Functional Description by a single 1.8, 2.5, or 3.3 V supply. The Si5325 is a low jitter, precision clock multiplier for applications requiring clock multiplication without jitter attenuation. The Si5325 accepts dual clock inputs ranging from 10 to 710 MHz and generates two independent, synchronous clock outputs ranging from 10 to 945 MHz and select frequencies to 1.4 GHz. The device provides virtually any frequency translation combination across this operating range. Independent dividers are available for each input clock and output clock, so the Si5325 can accept input clocks at different frequencies and it can generate output clocks at different frequencies. The Si5325 input clock frequency and clock multiplication ratio are programmable through an I2C or SPI interface. Silicon Laboratories offers a PC-based software utility, DSPLLsim, that can be used to determine the optimum PLL divider settings for a given input frequency/clock multiplication ratio combination that minimizes phase noise and power consumption. This utility can be downloaded from www.silabs.com/timing. 1.1. Further Documentation Consult the Silicon Laboratories Any-Rate Precision Clock Family Reference Manual (FRM) for more detailed information about the Si5325. The FRM can be downloaded from www.silabs.com/timing. Silicon Laboratories has developed a PC-based software utility called DSPLLsim to simplify device configuration, including frequency planning and loop bandwidth selection. This utility can be downloaded from www.silabs.com/timing. The Si5325 is based on Silicon Laboratories' 3rdgeneration DSPLL(R) technology, which provides anyrate frequency synthesis in a highly integrated PLL solution that eliminates the need for external VCXO and loop filter components. The Si5325 PLL loop bandwidth is digitally programmable and supports a range from 30 kHz to 1.3 MHz. The DSPLLsim software utility can be used to calculate valid loop bandwidth settings for a given input clock frequency/clock multiplication ratio. In the case when the input clocks enter alarm conditions, the PLL will freeze the DCO output frequency near its last value to maintain operation with an internal state close to the last valid operating state. The Si5325 has two differential clock outputs. The electrical format of each clock output is independently programmable to support LVPECL, LVDS, CML, or CMOS loads. If not required, the second clock output can be powered down to minimize power consumption. The phase difference between the selected input clock and the output clocks is adjustable in 200 ps increments for system skew control. In addition, the phase of one output clock may be adjusted in relation to the phase of the other output clock. The resolution varies from 800 ps to 2.2 ns depending on the PLL divider settings. Consult the DSPLLsim configuration software to determine the phase offset resolution for a given input clock/clock multiplication ratio combination. For systemlevel debugging, a bypass mode is available which drives the output clock directly from the input clock, bypassing the internal DSPLL. The device is powered Preliminary Rev. 0.26 5 Si5325 CLKOUT1+ CLKOUT1- NC GND NC VDD CLKOUT2- CLKOUT2+ CMODE 2. Pin Descriptions: Si5325 36 35 34 33 32 31 30 29 28 RST 1 27 SDI NC 2 26 A2_SS INT_C1B 3 25 A1 C2B 4 24 A0 GND Pad VDD 5 23 SDA_SDO GND 6 22 SCL NC 7 21 CS_CA GND 8 20 NC 19 NC NC 9 NC CLKIN1- CLKIN1+ VDD NC CLKIN2- VDD CLKIN2+ VDD 10 11 12 13 14 15 16 17 18 Pin numbers are preliminary and subject to change. Table 3. Si5325 Pin Descriptions Pin # Pin Name I/O Signal Level Description 1 RST I LVCMOS External Reset. Active low input that performs external hardware reset of device. Resets all internal logic to a known state and forces the device registers to their default value. Clock outputs are tristated during reset. After rising edge of RST signal, the Si5325 will perform an internal self-calibration. This pin has a weak pull-up. 2, 7, 9, 14, 18, 19, 20, 30, 33 NC -- -- 3 INT_C1B O LVCMOS No Connect. This pin must be left unconnected for normal operation. Interrupt/CKIN1 Invalid Indicator. This pin functions as a device interrupt output or an alarm output for CKIN1. If used as an interrupt output, INT_PIN must be set to 1. The pin functions as a maskable interrupt output with active polarity controlled by the INT_POL register bit. If used as an alarm output, the pin functions as a LOS (and optionally FOS) alarm indicator for CKIN1. Set CK1_BAD_PIN = 1 and INT_PIN = 0. 0 = CKIN1 present. 1 = LOS (FOS) on CKIN1. The active polarity is controlled by CK_BAD_POL. If no function is selected, the pin tristates. Note: Internal register names are indicated by underlined italics, e.g. INT_PIN. See Si5325 Register Map. 6 Preliminary Rev. 0.26 Si5325 Table 3. Si5325 Pin Descriptions (Continued) Pin # Pin Name I/O Signal Level Description 4 C2B O LVCMOS CKIN2 Invalid Indicator. This pin functions as a LOS (and optionally FOS) alarm indicator for CKIN2 if CK2_BAD_PIN = 1. 0 = CKIN2 present. 1 = LOS (FOS) on CKIN2. The active polarity can be changed by CK_BAD_POL. If CK2_BAD_PIN = 0, the pin tristates. 5, 10, 11, 15, 32 VDD VDD Supply Supply. The device operates from a 1.8, 2.5, or 3.3 V supply. Bypass capacitors should be associated with the following Vdd pins: 5 0.1 F 10 0.1 F 32 0.1 F A 1.0 F should be placed as close to device as is practical. 6, 8, 31 GND GND Supply Ground. Must be connected to system ground. Minimize the ground path impedance for optimal performance of this device. 12 13 CKIN2+ CKIN2- I Multi Clock Input 2. Differential input clock. This input can also be driven with a single-ended signal. Input frequency range is 10 to 710 MHz. 16 17 CKIN1+ CKIN1- I Multi Clock Input 1. Differential input clock. This input can also be driven with a single-ended signal. Input frequency range is 10 to 710 MHz. 21 CS_CA I/O LVCMOS Input Clock Select/Active Clock Indicator. In manual clock selection mode, this pin functions as the manual input clock selector if the CKSEL_PIN is set to 1. 0 = Select CKIN1. 1 = Select CKIN2. If CKSEL_PIN = 0, the CKSEL_REG register bit controls this function and this input tristates. In automatic clock selection mode, this pin indicates which of the two input clocks is currently the active clock. If alarms exist on both clocks, CA will indicate the last active clock that was used before entering the digital hold state. The CK_ACTV_PIN register bit must be set to 1 to reflect the active clock status to the CA output pin. 0 = CKIN1 active input clock. 1 = CKIN2 active input clock. If CK_ACTV_PIN = 0, this pin will tristate. The CA status will always be reflected in the CK_ACTV_REG read only register bit. Note: Internal register names are indicated by underlined italics, e.g. INT_PIN. See Si5325 Register Map. Preliminary Rev. 0.26 7 Si5325 Table 3. Si5325 Pin Descriptions (Continued) Pin # Pin Name I/O Signal Level Description 22 SCL I LVCMOS Serial Clock/Serial Clock. This pin functions as the serial clock input for both SPI and I2C modes. 23 SDA_SDO I/O LVCMOS Serial Data. In I2C control mode (CMODE = 0), this pin functions as the bidirectional serial data port. In SPI control mode (CMODE = 1), this pin functions as the serial data output. 25 24 A1 A0 I LVCMOS Serial Port Address. In I2C control mode (CMODE = 0), these pins function as hardware controlled address bits. In SPI control mode (CMODE = 1), these pins are ignored. 26 A2_SS I LVCMOS Serial Port Address/Slave Select. In I2C control mode (CMODE = 0), this pin functions as a hardware controlled address bit. In SPI control mode (CMODE = 1), this pin functions as the slave select input. 27 SDI I LVCMOS Serial Data In. In I2C control mode (CMODE = 0), this pin is ignored. In SPI control mode (CMODE = 1), this pin functions as the serial data input. 29 28 CKOUT1- CKOUT1+ O Multi Output Clock 1. Differential output clock with a frequency range of 10 MHz to 1.4175 GHz. Output signal format is selected by SFOUT1_REG register bits. Output is differential for LVPECL, LVDS, and CML compatible modes. For CMOS format, both output pins drive identical single-ended clock outputs. 34 35 CKOUT2- CKOUT2+ O Multi Output Clock 2. Differential output clock with a frequency range of 10 MHz to 1.4175 GHz. Output signal format is selected by SFOUT2_REG register bits. Output is differential for LVPECL, LVDS, and CML compatible modes. For CMOS format, both output pins drive identical single-ended clock outputs. 36 CMODE I LVCMOS GND PAD GND GND Supply Control Mode. Selects I2C or SPI control mode for the Si5325. 0 = I2C Control Mode. 1 = SPI Control Mode. Ground Pad. The ground pad must provide a low thermal and electrical impedance to a ground plane. Note: Internal register names are indicated by underlined italics, e.g. INT_PIN. See Si5325 Register Map. 8 Preliminary Rev. 0.26 Si5325 3. Ordering Guide Ordering Part Number Output Clock Frequency Range Package Temperature Range Si5325A-B-GM 10-945 MHz 970-1134 MHz 1.213-1.417 GHz 36-Lead 6 x 6 mm QFN -40 to 85 C Si5325B-B-GM 10-808 MHz 36-Lead 6 x 6 mm QFN -40 to 85 C Si5325C-B-GM 10-346 MHz 36-Lead 6 x 6 mm QFN -40 to 85 C Preliminary Rev. 0.26 9 Si5325 4. Package Outline: 36-Pin QFN Figure 3 illustrates the package details for the Si5325. Table 4 lists the values for the dimensions shown in the illustration. Figure 3. 36-Pin Quad Flat No-lead (QFN) Table 4. Package Dimensions Symbol Millimeters Symbol Millimeters Min Nom Max A 0.80 0.85 0.90 A1 0.00 0.01 0.05 -- -- 12 b 0.18 0.23 0.30 aaa -- -- 0.10 bbb -- -- 0.10 ccc -- -- 0.05 D D2 6.00 BSC 3.95 4.10 4.25 L Min Nom Max 0.50 0.60 0.75 e 0.50 BSC ddd -- -- 0.10 E 6.00 BSC eee -- -- 0.05 E2 3.95 4.10 4.25 Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to JEDEC outline MO-220, variation VJJD. 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification for Small Body Components. 10 Preliminary Rev. 0.26 Si5325 5. Recommended PCB Layout Figure 4. PCB Land Pattern Diagram Preliminary Rev. 0.26 11 Si5325 Table 5. PCB Land Pattern Dimensions Dimension MIN MAX e 0.50 BSC. E 5.42 REF. D 5.42 REF. E2 4.00 4.20 D2 4.00 4.20 GE 4.53 -- GD 4.53 -- X -- 0.28 Y 0.89 REF. ZE -- 6.31 ZD -- 6.31 Notes (General): 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing is per the ANSI Y14.5M-1994 specification. 3. This Land Pattern Design is based on IPC-SM-782 guidelines. 4. All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition (LMC) is calculated based on a Fabrication Allowance of 0.05 mm. Notes (Solder Mask Design): 1. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 m minimum, all the way around the pad. Notes (Stencil Design): 1. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 2. The stencil thickness should be 0.125 mm (5 mils). 3. The ratio of stencil aperture to land pad size should be 1:1 for the perimeter pads. 4. A 4 x 4 array of 0.80 mm square openings on 1.05 mm pitch should be used for the center ground pad. Notes (Card Assembly): 1. A No-Clean, Type-3 solder paste is recommended. 2. The recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification for Small Body Components. 12 Preliminary Rev. 0.26 Si5325 DOCUMENT CHANGE LIST Revision 0.23 to Revision 0.24 Clarified that the two outputs have a common, higher frequency source on page 1. Changed LVTTL to LVCMOS in Table 2, "Absolute Maximum Ratings," on page 3. Added Figure 1, "Typical Phase Noise Plot," on page 4. Updated "2. Pin Descriptions: Si5325". Removed references to latency control, INC, and DEC. Changed font for register names to underlined italics. Updated "3. Ordering Guide" on page 9. Added "5. Recommended PCB Layout". Revision 0.24 to Revision 0.25 Updated Section "2. Pin Descriptions: Si5325" on page 6. Revision 0.25 to Revision 0.26 Removed Figure 1. "Typical Phase Noise Plot." Changed pins 11 and 15 from NC to VDD in "2. Pin Descriptions: Si5325". Preliminary Rev. 0.26 13 Si5325 CONTACT INFORMATION Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 Tel: 1+(512) 416-8500 Fax: 1+(512) 416-9669 Toll Free: 1+(877) 444-3032 Email: Clockinfo@silabs.com Internet: www.silabs.com The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories, Silicon Labs, and DSPLL are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders. 14 Preliminary Rev. 0.26