(R) Amphenol Cylindrical Connectors for Printed Circuit Board Applications 12-170-2 This catalog has been specifically designed to assist in the critical process of selecting the right cylindrical connector for a printed circuit board application. Contact arrangements have been carefully selected to guide designers to the most commonly available and widely used insert patterns. Pin-out location illustrations of these contact insert patterns are shown first, followed by connector shell drawings in three series: MIL-DTL-38999, MIL-C-26482, MIL-5015. Proven & reliable cylindrical connector solutions for PC board attachment: MIL-DTL-38999, MIL-C-26482 and MIL-5015, with a wide range of contact arrangements and options Amphenol Corporation Amphenol Aerospace 40-60 Delaware Avenue, Sidney, New York 13838-1395 Phone: 800-678-0141 or 607-563-5011 Fax: 607-563-5157 www.amphenol-aerospace.com Amphenol For more information on the wide variety of PC tail contacts that are offered by Amphenol, see catalog 12-130, High Frequency Contacts, which also includes coax, twinax, triax and quadrax shielded contacts. 17 10 25 32 4 40 1 47 53 55 52 3 9 16 24 31 39 46 (R) Amphenol Cylindrical Connectors for Printed Circuit Board Applications 12-170-2 This catalog has been specifically designed to assist in the critical process of selecting the right cylindrical connector for a printed circuit board application. Contact arrangements have been carefully selected to guide designers to the most commonly available and widely used insert patterns. Pin-out location illustrations of these contact insert patterns are shown first, followed by connector shell drawings in three series: MIL-DTL-38999, MIL-C-26482, MIL-5015. Proven & reliable cylindrical connector solutions for PC board attachment: MIL-DTL-38999, MIL-C-26482 and MIL-5015, with a wide range of contact arrangements and options Amphenol Corporation Amphenol Aerospace 40-60 Delaware Avenue, Sidney, New York 13838-1395 Phone: 800-678-0141 or 607-563-5011 Fax: 607-563-5157 www.amphenol-aerospace.com Amphenol For more information on the wide variety of PC tail contacts that are offered by Amphenol, see catalog 12-130, High Frequency Contacts, which also includes coax, twinax, triax and quadrax shielded contacts. 17 10 25 32 4 40 1 47 53 55 52 3 9 16 24 31 39 46 Table of Contents Amphenol(R) Cylindrical Connectors for Printed Circuit Board Applications Page Introduction .............................................................................. 1 Amphenol has earned the reputation as the leader in the military electrical connection arena. Amphenol's interconnects meet almost any aerospace and ground vehicle design need as well as many industrial needs. Guide to Selecting a PCB Cylindrical Connector .................. 2, 3 Insert Availability ...................................................................... 4 Insert Arrangment Drawings ................................................ 5-24 Alternate Positioning ......................................................... 25-26 MIL-DTL-38999, Series I (LJT) Shell Styles ...................... 27-31 MIL-DTL-38999, Series II (JT) Shell Styles ....................... 32-34 MIL-DTL-38999, Series III (Tri-Start) Shell Styles ............. 35-39 Stand-off Adapter for use with MIL-DTL-38999 PCB Connectors ..................................................................... 40 MIL-C-26482, Series 1 (PT) Shell Styles .......................... 41, 42 MIL-5015 (MS3102) Shell Style .............................................. 43 Universal Header Assemblies for use with Flex print or PCB Connectors ........................................... 44, 45 Additional Products - Rectangular, for PCB Application ... 46-48 Amphenol Sales Office and Distributor Listing If more information is needed concerning the products in this publication, or if you have any special application needs, please contact your nearest Amphenol sales office or Amphenol Corporation at the following address: Amphenol Corporation Amphenol Aerospace 40-60 Delaware Ave., Sidney, NY 13838-1395 Phone: 800-678-0141 or 607-563-5011 Fax: 607-563-5157 See this catalog and the majority of catalogs of Amphenol Aerospace and Amphenol Industrial Interconnection Products at: www.amphenol-aerospace.com Amphenol operates quality systems that are certified to ISO9001:2000 by third party registrars. Table of Contents Amphenol(R) Cylindrical Connectors for Printed Circuit Board Applications Page Introduction .............................................................................. 1 Amphenol has earned the reputation as the leader in the military electrical connection arena. Amphenol's interconnects meet almost any aerospace and ground vehicle design need as well as many industrial needs. Guide to Selecting a PCB Cylindrical Connector .................. 2, 3 Insert Availability ...................................................................... 4 Insert Arrangment Drawings ................................................ 5-24 Alternate Positioning ......................................................... 25-26 MIL-DTL-38999, Series I (LJT) Shell Styles ...................... 27-31 MIL-DTL-38999, Series II (JT) Shell Styles ....................... 32-34 MIL-DTL-38999, Series III (Tri-Start) Shell Styles ............. 35-39 Stand-off Adapter for use with MIL-DTL-38999 PCB Connectors ..................................................................... 40 MIL-C-26482, Series 1 (PT) Shell Styles .......................... 41, 42 MIL-5015 (MS3102) Shell Style .............................................. 43 Universal Header Assemblies for use with Flex print or PCB Connectors ........................................... 44, 45 Additional Products - Rectangular, for PCB Application ... 46-48 Amphenol Sales Office and Distributor Listing If more information is needed concerning the products in this publication, or if you have any special application needs, please contact your nearest Amphenol sales office or Amphenol Corporation at the following address: Amphenol Corporation Amphenol Aerospace 40-60 Delaware Ave., Sidney, NY 13838-1395 Phone: 800-678-0141 or 607-563-5011 Fax: 607-563-5157 See this catalog and the majority of catalogs of Amphenol Aerospace and Amphenol Industrial Interconnection Products at: www.amphenol-aerospace.com Amphenol operates quality systems that are certified to ISO9001:2000 by third party registrars. Amphenol (R)Cylindrical Connectors for Printed Circuit Board Applications Amphenol provides three popular connector series with PC tail contacts. The following key points give a quick overview of these series. For more detail, there are series catalogs available as listed below*. Go to www.amphenol-aerospace.com to view and download these catalogs. There is a guide to selecting a cylindrical connector with printed circuit board contacts on the following page to assist you further. MIL-DTL-38999 CONNECTORS, METAL & COMPOSITE * * * * * Lightweight, compact, high density and high reliability cylindrical Operating voltage to 900 VAC (RMS) at sea level Environmentally resistant Solder or crimp rear release contacts in mating plug Series I (LJT) - Bayonet coupling * Scoop-proof (recessed pins) offers maximum contact protection * Series II (JT) - Bayonet coupling * For applications requiring maximum weight/space savings and reliability * Series III (Tri-Start) - Threaded, quick coupling in one complete turn Special 38999 Connector with * Designed for general duty as well as severe environmental Stand-off Shell and PC Tails applications * Superior EMI shielding with grounding fingers and metal-to-metal mating * Filter/Transient protection versions available * Scoop-proof contact protection * Stainless steel firewall versions, and composite versions 38999 Series III Box Mount Connector with PC Tails 38999 Series III Connector with a Special Configuration Composite Shell and PC Tails MIL-C-26482 CONNECTORS * Medium size, widely used cylindrical * Operating voltage to 1,000 VAC (RMS) at sea level * Series 1 (PT) - Bayonet coupling - most commonly used in PCB applications * Environmentally resistant * Solder or crimp front and rear release contacts in mating plug Black/green zinc alloy plating (cadmium-free) available 26482 Series 1 Jam Nut Connector with PC Tails 5015 Box Mount Connector with PC Tails MIL-5015 CONNECTORS * * * * * * Medium-heavy weight, time-tested cylindrical Operating voltage to 1,500 VAC (RMS) at sea level Environmentally resistant or general duty Threaded coupling Solder or crimp rear insertion contacts in mating plug Black/green zinc alloy plating (cadmium-free) available Also provided in this catalog are several additional product options for the designer of PCB board applications. For example: Amphenol's flex assemblies provide solutions for attachment to PCB boards where a self-locking terminal pad is needed or in tight-fitting space requirements. Connectors with compliant pin contacts are available, and pc tails within shielded coax, twinax and triax contacts are available. At the end of the catalog, see a brief description of Amphenol PCB rectangular connectors, backplane assemblies, terminal blocks and wiring interface modules. Go to www.amphenol-aerospace for catalogs online. 11 Flex Termination with MIL-C-26482 Special Connector * Request Catalog 12-090 for MIL-DTL-38999 Series I, II Request Catalog 12-092 for MIL-DTL-38999 Series III Request Catalog 12-070 for MIL-C-26482, Series 1, 2 Request Catalog 12-071 for Matrix MIL-C-26482 Series 2 Request Catalog 12-020 for MIL-5015 Note: MIL-DTL-38999 supersedes MIL-C-38999. Guide to Selecting a PCB Cylindrical Connector The connector selection process is one of the most important engineering decisions to be made in any electronic application. Amphenol has created this catalog specifically to provide the necessary information to select, layout and design both the appropriate Amphenol(R) cylindrical connector with PCB contacts and the connector footprint (contact locations) on the printed circuit board. The guide that follows is for application of cylindrical connectors on rigid printed circuit boards and also applies if a flex print assembly or other optional is being used. Engineers working on those PCB or flex print applications requiring rectangular connectors are encouraged to refer to page 46-48 and ask for Amphenol Rectangular Product catalogs. How To Select a Cylindrical Connector for a PCB Application The data provided in this catalog is based on three cylindrical connector series: MIL-DTL-38999 Series I, II and III, MIL-C-26482 Series 1, and MIL-C-5015. See page 1 for electrical and environmental features and differences of these three series. The "hot" side of the application determines the choice of pin or socket genders of the contacts. How to Measure the PCB Tail Length The tail length of the PCB is the portion of the contact that extends beyond the rear of the shell. This length will vary in relationship to the mounting flange, depending on the series of connector selected. Standard lengths are shown on the connector shell style drawings in this catalog. These shell style drawing pages also provide how to order part numbering for standard PCB cylindrical connectors. When computing the desired tail length, it is important to take into consideration the following factors: * The connector series and shell style. * The mounting style of the receptacle; jam nut (D hole) or panel mount (four holes). This can affect the overall length of the tail. * The extension of the tail beyond the opposite side of the board or the flex. * The space required to adequately clean flux from between the board or flex and the rear of the connector shell. Connectors that are mounted flush against the board may trap soldering flux which could lead to corrosion of the solder joints. Would Alignment Discs, Headers or Special Stand-off Shells be Beneficial? Any mechanical methods needed to stabilize the board or flex to the connector and/or the panel. The PCB tails shown in this catalog are of one diameter. Stepped tails or PCB tails with an increased diameter on a designated portion may be required for certain applications. Alignment discs are available which provide ease of alignment of pins to boards, protection during shipment and optimized electrical circuit separation. Header assemblies (see pages 44 & 45) are available which provide time and cost saving potentials. Standoffs may be required for certain applications. Amphenol has developed a new stand-off adapter (see page 40) which may eliminate the need for special stand-off shell designs. Connectors with clinch nuts can be provided. Please call Amphenol to discuss any optional designs or any special requirements. Stand-off Adapter on a Jam Nut Receptacle. Special Design with Longer PC Tails in a 38999 Composite Shell Connector. Also shows an Alignment Disc. 2 Universal Header Assemblies are available for Flex Print/PC Board Mounting. Beneficial especially when electrical testing of the connector requires it to be removed and reattached. Guide to Selecting a PCB Cylindrical Connector, cont. What Determines the Diameter of the PCB Tail? The outside diameter of the PCB tail is determined by the inside diameter of the plated through-hole on the board or flex print. The standard or most popular diameters are shown in the chart on the next page and are called out in the connector illustrations in this catalog (Pgs. 26-37). Standard diameters of PCB tails Size 16 Contact Size 20 Contact Size 22D Contact MIL-DTL-38999 Connector Series .062 .001 .019 .001 .019 .001 MIL-C-26482 .030 .001 .030 .001 Not available MIL-5015 .030 .001 Not available Not available For availability of other contact diameters, consult Amphenol, Sidney NY. Should PCB Tails be Gold Plated or Pre-tinned? The standard PCB tails for MIL-DTL-38999 and MIL-C-26482 receptacles have gold plating, .00050 inches over nickel. PCB tails for MIL-C-5015 receptacles are plated with silver, .00010 inches over copper. Amphenol can substitute a pre-tinned version of these tails to facilitate the termination process. This pre-tinning is a 60/40 lead-tin alloy. Call Amphenol for further information on pre-tinning and any other plating of contacts not covered in this catalog. Would Flex Assemblies be Necessary or Beneficial for the Application? Flex print can radically simplify the assembly of a connector to a system, as well as eliminate wiring errors. Amphenol offers connector flex assemblies through ACT, Advanced Circuit Technologies division. Features and benefits of using flex technology include: * Available for MIL-DTL-38999 (including filter EMI/EMP types), MIL-5015 and MIL-C-26482 cylindrical connectors * Sculptures(R) Flexible Circuits with built-in terminations * Eliminates failures associated with crimped or solder-on contacts * Geometrically fit tight space requirements and create a self-locking terminal pad Flex Termination for Attachment to PC Boards Should Other PC Tail Contact Types be Considered? Press-Fit Connectors with compliant pins are available which engage the plated through-holes in the board without the need for soldering. This optional contact style offers the following benefits * Easy board repairability * Improved board processing time * Excellent temperature performance * Ideal for low-lead applications For more information on Press-Fit connectors with compliant pins refer to Amphenol data sheet #188. Special Quadrax contacts have been designed with PC tails. Coax, twinax and triax contacts can also have PC tails. Refer to Amphenol catalog 12-130. Go online at www.amphenol-aerospace.com or consult Amphenol Aerospace for further information. 3 Compliant Pin Contacts in a Bayonet 38999 Catalog Quadrax PC Tail Contacts Combined with Standard PC Tail Contacts Quadrax Contacts with PC Tails in a 38999 Connector with Special Stand-off Shell Cylindrical Connectors with PCB contacts insert availability The following table lists the most commonly used insert arrangements for printed circuit board application of MIL-DTL-38999, MIL-C-26482 and MIL-C-5015 cylindrical connectors. This represents the most readily available patterns within these series. See illustrations of these selected patterns on the following pages. If you require other arrangements than what are shown here, consult Amphenol for further availability. MIL-DTL-38999 Contact Size* JT Series II LJT Series I Tri-Start Series III 8-3 9-3 8-35 9-35 9-35 8-98 9-98 9-98 8-98 A 3 10-5 11-5 11-5 10-5 I 5 5 10-6 I 6 6 MIL-C-26482 MIL-5015 8-3 10SL-3 11-6 10-35 11-35 12-3 13-3 12-35 13-35 11-35 Service Rating Total Contacts M/I 3 M 6 I 3 M 13 12-3 II 3 12-10 I 10 13-35 14S-6 M 22 Inst. 6 22D 20 3 6 3 3 13 3 10 22 6 14-18 15-18 15-18 14-18 I 18 18 14-19 15-19 15-19 14-19 I 19 19 14-35 15-35 15-35 M 37 16-26 17-26 17-26 16-35 17-35 17-35 16S-1 16-26 18-1 18-11 19-11 19-11 18-11 18-32 19-32 19-32 18-32 18-35 19-35 19-35 20-11 20-27 21-27 20-35 21-35 21-35 20-27 20-41 21-41 21-41 22-35 23-35 23-35 22-55 23-55 23-55 20-41 22-14 24-31 22-55 25-35 25-35 24-61 25-61 25-61 7 I 26 37 7 26 M 55 A/Inst. 10 10 II 11 11 I 32 M 66 Inst. 13 I 27 M 79 I 41 A 19 M 100 55 32 66 13 27 79 41 19 100 I 55 24-5 A 16 16 24-28 Inst. 24 24 24-31 24-35 A 16 24-61 28-15 * For information on size 12 PC tail contacts consult Amphenol Aerospace. 4 I 31 M 128 I 61 A 35 55 31 128 61 35 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #8-3 / 9-3 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: 8-3 9-3 MIL-C-26482 Series 1 & 2 MIL-5015 8-3 NA NA Contact Locations Front face of pin insert shown Number of Contacts Contact Size Service Rating* 3 20 M/I .018 .079 C A B .056 *Service Rating: M for MIL-DTL-38999 I for MIL-C-26482 .056 Insert Arrangement #8-35 /9-35 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: 8-35 9-35 Contact Locations Front face of pin insert shown MIL-C-26482 Series 1 & 2 MIL-5015 NA NA 9-35 Number of Contacts Contact Size Service Rating 6 22D M .045 .078 .045 1 5 4 6 2 3 .090 .078 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 5 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #8-98 / 9-98 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: 8-98 9-98 MIL-C-26482 Series 1 & 2 MIL-5015 8-98 NA 9-98 Contact Locations Front face of pin insert shown Number of Contacts Contact Size Service Rating 3 20 I .038 .075 A C B .065 .065 Insert Arrangement #10SL-3 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: NA NA MIL-C-26482 Series 1 & 2 MIL-5015 NA 10SL-3 NA Contact Locations Front face of pin insert shown Number of Contacts Contact Size Service Rating 3 16 A .053 C A B .105 .091 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 6 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #10-5 / 11-5 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: 10-5 11-5 MIL-C-26482 Series 1 & 2 MIL-5015 10-5 NA 11-5 Contact Locations Front face of pin insert shown Number of Contacts Contact Size Service Rating 5 20 I .065 .065 .056 .130 A E D B C .065 .113 .113 Insert Arrangement #10-6 / 11-6 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: NA 11-6 10-6 NA Number of Contacts Contact Size Service Rating 6 20 I .130 A MIL-5015 NA Contact Locations Front face of pin insert shown F MIL-C-26482 Series 1 & 2 .065 B C E D .065 .130 .113 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 7 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #10-35 / 11-35 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: 10-35 11-35 MIL-C-26482 Series 1 & 2 MIL-5015 NA NA 11-35 Contact Locations Front face of pin insert shown Number of Contacts Contact Size Service Rating 13 22D M .138 .085 .118 .146 .056 .146 9 10 1 11 13 8 2 3 12 4 7 6 5 .045 .045 .035 .118 .049 Insert Arrangement #12-3 / 13-3 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: 12-3 13-3 MIL-C-26482 Series 1 & 2 MIL-5015 12-3 NA NA Contact Locations Front face of pin insert shown Number of Contacts Contact Size Service Rating 3 16 II .058 C A B .111 .094 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 8 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #12-10 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: NA NA MIL-C-26482 Series 1 & 2 MIL-5015 12-10 NA NA Contact Locations Front face of pin insert shown Number of Contacts Contact Size Service Rating 10 20 I .065 A H K B J C G F E D .120 .130 .195 Insert Arrangement #12-35 / 13-35 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: 12-35 13-35 Contact Locations Front face of pin insert shown MIL-C-26482 Series 1 & 2 MIL-5015 NA NA 13-35 Number of Contacts Contact Size Service Rating 22 22D M .182 .126 .107 .117 .088 .045 .158 .197 .026 .075 1 21 11 .030 .120 .093 .203 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 9 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #14S-6 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: NA NA MIL-C-26482 Series 1 & 2 MIL-5015 NA 14S-6 NA Contact Locations Front face of pin insert shown Number of Contacts Contact Size Service Rating 6 16 Inst. A F .160 B E C .080 D .138 Insert Arrangement #14-18 / 15-18 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: 14-18 15-18 MIL-5015 14-18 NA 15-18 Contact Locations Front face of pin insert shown .260 MIL-C-26482 Series 1 & 2 Number of Contacts Contact Size Service Rating 18 20 I .260 .113 L K M T J .252 A N B U S P C R H D G F E .113 .225 .065 .065 .130 .195 .130 .195 All dimensions for reference only. For alternate rotations see pages 25 & 26 Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 10 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #14-19 / 15-19 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: 14-19 15-19 MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating 14-19 NA 19 20 I 15-19 Contact Locations Front face of pin insert shown .065 .065 .225 .113 A M .113 L B N C K U J T H V R D S G E F .130 .130 .195 .225 .195 .260 .260 Insert Arrangement #14-35 / 15-35 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: 14-35 Contact Locations Front face of pin insert shown 1 31 11 21 15-35 MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating NA NA 37 22D M 15-35 Contact Hole Locations Location X Axis Y Axis +.045 +.262 +.123 +.217 +.211 +.160 +.254 +.080 +.266 -.010 +.247 -.098 +.200 -.175 +.130 -.232 +.045 -.262 -.045 -.262 -.130 -.232 -.200 -.175 -.247 -.098 -.266 -.010 -.254 +.080 -.211 +.160 -.123 +.217 -.045 +.262 +.045 +.172 +.123 +.119 Contact Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 11 Contact Hole Locations Location X Axis Y Axis +.170 +.040 +.170 -.050 +.123 -.127 +.045 -.172 -.045 -.172 -.123 -.127 -.170 -.050 -.170 +.040 -.123 +.119 -.045 +.172 +.045 +.074 +.090 -.004 +.045 -.082 -.045 -.082 -.090 -.004 -.045 +.074 .000 -.004 Contact Number 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #16S-1 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: NA NA MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating NA 16S-1 7 16 A MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating 16-26 NA 26 20 I NA Contact Locations Front face of pin insert shown .095 .165 F E A G D B C .190 Insert Arrangement #16-26 / 17-26 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: NA 17-26 Contact Locations Front face of pin insert shown A R P a B T S U b C D N Z M Y L V c K J W X H E F G 17-26 Contact Hole Locations Location X Axis Y Axis .000 +.321 +.131 +.293 +.239 +.214 +.305 +.099 +.319 -.034 +.278 -.161 +.189 -.260 +.067 -.314 -.067 -.314 -.189 -.260 -.278 -.161 -.319 -.034 -.305 +.099 -.239 +.214 Contact Number A B C D E F G H J K L M N P All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 12 Contact Hole Locations Location X Axis Y Axis -.131 +.293 -.070 +.177 +.070 +.177 +.175 +.094 +.178 -.036 +.119 -.151 .000 -.203 -.119 -.151 -.178 -.036 -.175 +.094 .000 +.065 .000 -.065 Contact Number R S T U V W X Y Z a b c Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #16-35 / 17-35 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: 16-35 17-35 Contact Locations Front face of pin insert shown 17 10 25 32 40 4 1 47 53 55 52 3 9 16 24 31 46 39 MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating NA NA 55 22D M 17-35 Contact Hole Locations Location X Axis Y Axis -.312 +.086 -.312 -.004 -.312 -.094 -.242 +.221 -.234 +.131 -.234 +.041 -.234 -.049 -.234 -.139 -.234 -.229 -.172 +.279 -.156 +.176 -.156 +.086 -.156 -.004 -.156 -.094 -.156 -.184 -.156 -.274 -.089 +.316 -.078 +.221 -.078 +.131 -.078 +.041 -.078 -.049 -.078 -.139 -.078 -.229 -.078 -.319 .000 +.329 .000 +.176 .000 +.086 .000 -.004 .000 -.094 .000 -.184 .000 -.274 Contact Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 13 Contact Hole Locations Location X Axis Y Axis +.089 +.316 +.078 +.221 +.078 +.131 +.078 +.041 +.078 -.049 +.078 -.139 +.078 -.229 +.078 -.319 +.172 +.279 +.156 +.176 +.156 +.086 +.156 -.004 +.156 -.094 +.156 -.184 +.156 -.274 +.242 +.221 +.234 +.131 +.234 +.041 +.234 -.049 +.234 -.139 +.234 -.229 +.312 +.086 +.312 -.004 +.312 -.094 Contact Number 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #18-1 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: NA NA MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating* NA 18-1 10 16 A/Inst. MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating 18-11 NA 11 16 II NA Contact Locations Front face of pin insert shown .095 A H G I B F J C D E .240 .240 * Contact Locations B, C, F, G are Service Rating A. All other contact locations are Service Rating Inst. .100 Insert Arrangement #18-11 / 19-11 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: 18-11 19-11 19-11 Contact Locations Front face of pin insert shown .250 .105 .105 .260 .132 J H A B K C G L F D .092 E .053 .281 .215 .179 .275 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 14 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #18-32 / 19-32 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: 18-32 19-32 T P N C f d W c X h K F Z a L J E Y b M D g j Contact Size Service Rating 18-32 NA 32 20 I Contact Hole Locations Location X Axis Y Axis +.066 +.353 +.189 +.305 +.286 +.217 +.345 +.098 +.357 -.033 +.321 -.160 +.242 -.265 +.130 -.335 .000 -.359 -.130 -.335 -.242 -.265 -.321 -.160 -.357 -.033 -.345 +.098 -.286 +.217 -.189 +.305 -.066 +.353 .000 +.230 B V e R Number of Contacts Contact Letter A B C D E F G H J K L M N P R S T U A U MIL-5015 19-32 Contact Locations Front face of pin insert shown S MIL-C-26482 Series 1 & 2 G H Contact Hole Locations Location X Axis Y Axis +.124 +.193 +.209 +.095 +.228 -.033 +.174 -.151 +.065 -.221 -.065 -.221 -.174 -.151 -.228 -.033 -.209 +.095 -.124 +.193 .000 +.096 +.096 .000 .000 -.096 -.096 .000 Contact Letter V W X Y Z a b c d e f g h j Insert Arrangement #18-35 / 19-35 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: 18-35 19-35 MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating NA NA 66 22D M 19-35 Contact Locations Front face of pin insert shown .357 .279 .360 .315 .201 .270 .225 .123 .045 .180 .135 17 4 23 34 43 10 51 58 .090 .045 64 1 3 66 63 9 16 24 33 42 50 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 15 57 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #20-11 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: NA NA MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating NA 20-11 13 16 Inst. NA Contact Locations Front face of pin insert shown .138 .159 .239 L C B M E .102 F G H K N A .080 J D .204 .276 .156 Insert Arrangement #20-27 / 21-27 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: 20-27 21-27 Contact Locations Front face of pin insert shown MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating 20-27 NA 27 20 I NA .400 .275 .225 .125 .100 .150 .225 .275 .375 .400 A B R P a N C b T Z M S d D c Y U E F L X W K V G J .400 .300 H .200 .100 .150 .250 .250 .150 .025 .375 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. .050 16 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #20-35 / 21-35 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: 20-35 21-35 MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating NA NA 79 22D M 21-35 Contact Hole Locations Contact Locations Front face of pin insert shown Contact Hole Locations Location Location Contact Number X Axis Y Axis Contact Number X Axis 10 +.365 -.227 45 -.332 -.048 11 +.306 -.302 46 -.332 +.048 12 +.232 -.362 47 -.311 +.141 13 +.146 -.404 48 -.258 +.220 14 +.053 -.426 49 -.184 +.280 15 -.053 -.426 50 -.098 +.322 16 -.146 -.404 51 -.048 +.241 17 -.232 -.362 52 +.048 +.241 18 -.306 -.302 53 +.134 +.199 19 -.365 -.227 54 +.208 +.139 20 -.406 -.141 55 +.237 +.048 21 -.427 -.048 56 +.237 -.048 22 -.427 +.048 57 +.208 -.139 23 -.406 +.141 58 +.134 -.199 24 -.365 +.227 59 +.048 -.241 25 -.306 +.302 60 -.048 -.241 26 -.232 +.362 61 -.134 -.199 27 -.146 +.404 62 -.208 -.139 28 -.053 +.426 63 -.237 -.048 29 .000 +.323 64 -.237 +.048 30 +.098 +.322 65 -.208 +.139 31 +.184 +.280 66 -.134 +.199 32 +.258 +.220 67 -.048 +.146 Contact Hole Locations 33 +.311 +.141 68 +.048 +.146 Location 34 +.332 +.048 69 +.125 +.090 1 31 51 79 21 71 61 41 11 Y Axis Contact Number X Axis Y Axis 35 +.332 -.048 70 +.155 .000 1 +.053 +.426 36 +.311 -.141 71 +.125 -.090 2 +.146 +.404 37 +.258 -.220 72 +.048 -.146 3 +.232 +.362 38 +.184 -.280 73 -.048 -.146 4 +.306 +.302 39 +.098 -.322 74 -.125 -.090 5 +.365 +.227 40 .000 -.347 75 -.155 .000 6 +.406 +.141 41 -.098 -.322 76 -.125 +.090 7 +.427 +.048 42 -.184 -.280 77 .000 +.053 8 +.427 -.048 43 -.258 -.220 78 +.048 -.029 -.141 44 -.311 -.141 79 -.048 -.029 9 +.406 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 17 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #20-41 / 21-41 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: 20-41 21-41 MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating 20-41 NA 41 20 I 21-41 Contact Locations Front face of pin insert shown W V j U C Y D k g P f p q N L G c d e M F b n E a t r R Z m s h S B X i T A H J K .300 DIA. .567 DIA. .835 DIA. Insert Arrangement #22-14 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: Contact Locations Front face of pin insert shown NA NA MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating NA 22-14 19 16 A NA .392 .196 .336 M L J N U K H C R S G B P V T A D .168 F E .098 .294 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 18 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #22-35 / 23-35 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: 22-35 23-35 Contact Locations Front face of pin insert shown 25 35 16 46 56 67 77 8 86 1 94 2 95 96 3 97 4 98 5 99 6 7 100 15 93 24 34 45 55 85 66 76 Contact Hole Locations Location X Axis Y Axis -.428 +.241 -.467 +.154 -.488 +.061 -.415 .000 -.488 -.061 -.428 -.142 -.428 -.237 -.332 +.333 -.332 +.238 -.332 +.143 -.332 +.048 -.332 -.047 -.332 -.142 -.332 -.237 -.332 -.332 -.249 +.380 -.249 +.285 -.249 +.190 Contact Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating NA NA 100 22D M 23-35 Contact Hole Locations Location X Axis Y Axis -.249 +.095 -.249 .000 -.249 -.095 -.249 -.190 -.249 -.285 -.249 -.380 -.166 +.428 -.166 +.333 -.166 +.238 -.166 +.143 -.166 +.048 -.166 -.047 -.166 -.142 -.166 -.237 -.166 -.332 -.166 -.427 -.083 +.475 -.083 +.380 -.083 +.285 -.083 +.190 -.083 +.095 -.083 .000 -.083 -.095 -.083 -.190 -.083 -.285 -.083 -.380 -.083 -.475 .000 +.428 .000 +.333 .000 +.238 .000 +.143 .000 +.048 .000 -.047 .000 -.142 .000 -.237 .000 -.332 .000 -.427 +.083 +.475 +.083 +.380 +.083 +.285 +.083 +.190 +.083 +.095 Contact Number 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 19 Contact Hole Locations Location X Axis Y Axis +.083 .000 +.083 -.095 +.083 -.190 +.083 -.285 +.083 -.380 +.083 -.475 +.166 +.428 +.166 +.333 +.166 +.238 +.166 +.143 +.166 +.048 +.166 -.047 +.166 -.142 +.166 -.237 +.166 -.332 +.166 -.427 +.249 +.380 +.249 +.285 +.249 +.190 +.249 +.095 +.249 .000 +.249 -.095 +.249 -.190 +.249 -.285 +.249 -.380 +.332 +.333 +.332 +.238 +.332 +.143 +.332 +.048 +.332 -.047 +.332 -.142 +.332 -.237 +.332 -.332 +.428 +.241 +.467 +.154 +.488 +.061 +.415 .000 +.488 -.061 +.428 -.142 +.428 -.237 Contact Number 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #22-55 / 23-55 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: 22-55 23-55 MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating 22-55 NA 55 20 I 23-55 Contact Locations Front face of pin insert shown .325 .260 A U T S R k .390 P j i N .130 p .455 q AA z GG y FF w h M C X Y D r BB CC Z E HH s a F DD t EE b u v c G d e H J W m x B V n g f L K .195 .065 .112 .225 .336 .450 Insert Arrangement #24-5 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: NA NA MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating NA 24-5 16 16 A NA Contact Locations Front face of pin insert shown .035 .067 .238 .137 A B C E D G F H K J L N M R P .168 S .270 .371 .352 .176 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 20 .340 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #24-28 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: NA NA MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating NA 24-28 24 16 Inst. NA Contact Locations Front face of pin insert shown .356 .178 .089 .308 B A E F L K W P N T S R J H G M Y Q V U X .154 D C Z .267 .445 Insert Arrangement #24-31 / 25-31 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: 24-31 NA MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating 24-31 NA 31 16 I NA Contact Locations Front face of pin insert shown M L A N Z .455 a Y c d W H D S V T U G C R e J .273 .091 b g X E F .158 .316 .474 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. .364 Q f K B P 21 .182 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #24-35 / 25-35 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: 24-35 25-35 Contact Locations Front face of pin insert shown 48 59 71 25 36 82 15 8 94 105115 1 125 4 7 121 14 24 35 47 58 70 114 81 93 104 Contact Hole Locations Location X Axis Y Axis -.479 +.279 -.520 +.190 -.546 +.095 -.555 .000 -.546 -.095 -.520 -.190 -.479 -.279 -.424 +.357 -.415 +.190 -.415 +.095 -.415 .000 -.415 -.095 -.415 -.190 -.424 -.357 -.332 +.444 -.332 +.332 -.332 +.237 -.332 +.142 -.332 +.047 -.332 -.047 -.332 -.142 -.332 -.237 -.332 -.332 -.332 -.427 -.249 +.496 -.249 +.380 -.249 +.285 Contact Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating NA NA 128 22D M 25-35 Contact Hole Locations Location X Axis Y Axis -.249 +.190 -.249 +.095 -.249 .000 -.249 -.095 -.249 -.190 -.249 -.285 -.249 -.380 -.249 -.475 -.160 +.531 -.166 +.427 -.166 +.332 -.166 +.237 -.166 +.142 -.166 +.047 -.166 -.047 -.166 -.142 -.166 -.237 -.166 -.332 -.166 -.427 -.166 -.522 -.083 +.475 -.083 +.380 -.083 +.285 -.083 +.190 -.083 +.095 -.083 .000 -.083 -.095 -.083 -.190 -.083 -.285 -.083 -.380 -.083 -.475 .000 +.522 .000 +.427 .000 +.332 .000 +.237 .000 +.142 .000 +.047 .000 -.047 .000 -.142 .000 -.237 .000 -.332 .000 -.427 .000 -.555 +.083 +.475 +.083 +.380 +.083 +.285 +.083 +.190 +.083 +.095 +.083 .000 +.083 -.095 Contact Number 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 22 Contact Hole Locations Location X Axis Y Axis +.083 -.190 +.083 -.285 +.083 -.380 +.083 -.475 +.160 +.531 +.166 +.427 +.166 +.332 +.166 +.237 +.166 +.142 +.166 +.047 +.166 -.047 +.166 -.142 +.166 -.237 +.166 -.332 +.166 -.427 +.166 -.522 +.249 +.496 +.249 +.380 +.249 +.285 +.249 +.190 +.249 +.095 +.249 .000 +.249 -.095 +.249 -.190 +.249 -.285 +.249 -.380 +.249 -.475 +.332 +.444 +.332 +.332 +.332 +.237 +.332 +.142 +.332 +.047 +.332 -.047 +.332 -.142 +.332 -.237 +.332 -.332 +.332 -.427 +.424 +.357 +.415 +.190 +.415 +.095 +.415 .000 +.415 -.095 +.415 -.190 +.424 -.357 +.479 +.279 +.520 +.190 +.546 +.095 +.555 .000 +.546 -.095 +.520 -.190 +.479 -.279 Contact Number 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #24-61 / 25-61 JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Connector Type: Insert Designation: 24-61 25-61 Y X u A v GG HH W t FF B b c C w x d D NN JJ e E PP y EE KK MM U r F f LL T G g q z DD BB CC AA h S H p J R i k j P m K N L M V s MIL-5015 Number of Contacts Contact Size Service Rating 24-61 NA 61 20 I 25-61 Contact Hole Locations Contact Locations Front face of pin insert shown Z a MIL-C-26482 Series 1 & 2 Contact Hole Locations Location Location Contact Number X Axis Y Axis Contact Number X Axis Y Axis A +.196 +.500 h +.341 -.213 B +.314 +.435 i +.251 -.314 C +.413 +.343 j +.133 -.379 D +.485 +.230 k .000 -.402 E +.527 +.101 m -.133 -.379 F +.536 -.030 n -.251 -.314 G +.511 -.164 p -.341 -.213 H +.454 -.287 q -.392 -.088 J +.368 -.391 r -.399 +.046 K +.259 -.470 s -.362 +.175 L +.134 -.519 t -.285 +.283 M .000 -.537 u -.173 +.363 N -.134 -.519 v .000 +.338 P -.259 -.470 w +.147 +.223 R -.368 -.391 x +.237 +.122 S -.454 -.287 y +.267 -.010 T -.511 -.164 z +.228 -.139 U -.536 -.030 AA +.131 -.233 V -.527 +.101 BB .000 -.267 -.233 W -.485 +.230 CC -.131 X -.413 +.343 DD -.228 -.139 Y -.314 +.435 EE -.267 -.010 Z -.196 +.500 FF -.237 +.122 a -.068 +.454 GG -.147 +.223 b +.068 +.454 HH .000 +.200 c +.173 +.363 JJ +.105 +.094 -.041 d +.285 +.283 KK +.135 e +.362 +.175 LL .000 -.132 f +.399 +.046 MM -.135 -.041 g +.392 -.088 NN -.105 +.094 PP .000 .000 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 23 Cylindrical Connectors with PCB contacts insert arrangements, cont. Insert Arrangement #28-15 Connector Type: JT LJT Tri-Start MIL-DTL-38999 MIL-DTL-38999 MIL-DTL-38999 Series II Series I Series III Insert Designation: NA NA MIL-C-26482 Series 1 & 2 MIL-5015 Number of Contacts Contact Size Service Rating NA 28-15 35 16 A NA Contact Locations Front face of pin insert shown .552 .460 .368 .276 .092 .229 B A C H .547 .388 X L S Y T N .089 c b g .070 W V U f e d G M a Z .407 .509 F K J R P E D h .248 j k l m .106 .184 All dimensions for reference only. For alternate rotations see pages 25 & 26. Note: Shown in this catalog are the most common insert patterns for PCB applications. For availability of other arrangements, consult Amphenol Corp., Sidney, NY. 24 Cylindrical Connectors with PCB contacts alternate positioning available for MIL-DTL-38999 connectors To avoid cross-plugging problems in applications requiring the use of more than one connector of the same series, size and arrangement, alternate rotations are available as indicated in the accompanying charts. In MIL-DTL-38999 Series I, II and III connectors the rotation is based on rotating the master key/keyway in the connector shell. A plug with a given rotation letter will mate with a receptacle with the same rotation letter. Only the master key/keyway rotates in the shell, and the insert always remains in the same position relative to the minor keys. Refer to diagrams below for each connector series. LJT (MIL-DTL-38999 Series I) KEY/KEYWAY ROTATION AB ANGLE OF ROTATION (Degrees) Shell Size 9 11 13 15 17 19 21 23 25 Normal 95 95 95 95 95 95 95 95 95 A 77 81 75 74 77 77 77 80 80 B - 67 63 61 65 65 65 69 69 C - 123 127 129 125 125 125 121 121 D 113 109 115 116 113 113 113 110 110 JT (MIL-DTL-38999 Series II) KEY/KEYWAY ROTATION NORMAL D C B A AB ROTATION LETTERS LJT & JT CONNECTORS ALTERNATE ROTATION CROSS REFERENCE LETTERS 5 LJT REF RELATIVE POSSIBLE POSITION OF ROTATED MASTER KEYWAY (front face of LJT connector receptacle shown) AB ANGLE OF ROTATION (Degrees) Shell Size 8 10 12 14 16 18 20 22 24 Normal 100 100 100 100 100 100 100 100 100 A 82 86 80 79 82 82 82 85 85 B - 72 68 66 70 70 70 74 74 C - 128 132 134 130 130 130 126 126 D 118 114 120 121 118 118 118 115 115 NORMAL D C B A AB ROTATION LETTERS Pins in Alternate Rotations PA = E PB = R PC = W PD = Y Sockets in Alternate Rotations SA = F SB = T SC = X SD = Z Explanation: Use P at end of part number for pin contacts in Normal position. Use S at end of part number for socket contacts in Normal position. Use cross reference letters given in chart above for alternate rotations. 10 JT REF Tri-Start (MIL-DTL-38999 Series III) KEY/KEYWAY ROTATION Shell Size 9 11, 13, and 15 17 and 19 21, 23, and 25 Key & Keyway Arrangement Identification Letter N A B C D E N A B C D E N A B C D E N A B C D E AR BSC 105 102 80 35 64 91 95 113 90 53 119 51 80 135 49 66 62 79 80 135 49 66 62 79 BR BSC 140 132 118 140 155 131 141 156 145 156 146 141 142 170 169 140 145 153 142 170 169 140 145 153 CR BSC 215 248 230 205 234 197 208 182 195 220 176 184 196 200 200 200 180 197 196 200 200 200 180 197 DR BSC 265 320 312 275 304 240 236 292 252 255 298 242 293 310 244 257 280 272 293 310 244 257 280 272 RELATIVE POSSIBLE POSITION OF ROTATED MASTER KEYWAY (front face of JT connector receptacle shown) MAIN KEYWAY AR BSC BR BSC DR BSC CR BSC RELATIVE POSSIBLE POSITION OF ROTATED MASTER KEYWAY (front face of Tri-Start connector receptacle shown) 25 TRI-START CONNECTORS ALTERNATE ROTATION CROSS REFERENCE LETTERS Pins in Alternate Rotations PA = G PB = I PC = K PD = M PE = R Sockets in Alternate Rotations SA = H SB = J SC = L SD = N SE = T Explanation: Use P at end of part number for pin contacts in Normal position. Use S at end of part number for socket contacts in Normal position. Use cross reference letters given in chart above for alternate rotations. Cylindrical Connectors with PCB contacts alternate positioning available for MIL-C-26482 and MIL-5015 connectors To avoid cross-plugging problems in applications requiring the use of more than one connector of the same series, size and arrangement, alternate rotations are available as indicated in the accompanying charts. In MIL-C-26482 and MIL-5015 connectors the rotation is based on rotation of the insert within the connector. A plug with a given rotation letter will mate with a receptacle with the same rotation letter. The front face of the pin insert is rotated within the shell in a clockwise direction from the normal shell key. Refer to diagram below for both MIL-C-26482 and MIL-C-5015 connectors. MIL-C-26482 INSERT ROTATION Position W X - - - 145 - 110 110 110 Y - - - 215 - 250 250 250 B A Pins in Sockets in Alternate Alternate Rotations Rotations PW = G SW = H PX = I SX = J PY = K SY = L PZ = M SZ = N Degrees W - - 80 70 - 80 80 80 Position Y MIL-26482 AND MIL-5015 CONNECTORS ALTERNATE ROTATION CROSS REFERENCE LETTERS Insert Rotation Insert Arrangement 10SL-3 14S-6 16S-1 18-1 20-11 22-14 24-28 28-15 Position X RELATIVE POSSIBLE POSITION OF ROTATED INSERT (front face of connector receptacle shown) (MIL-C-26482 and MIL-C-5015) MIL-5015 INSERT ROTATION Shell Size 10 14 16 18 20 22 24 28 A Z - - 270 270 - 338 265 - 288 - 324 A B Degrees X Y 210 - - - 151 180 90 180 165 315 - 275 138 222 126 225 144 216 225 255 180 270 B W 60 - 45 15 30 60 85 45 72 90 90 A Insert Arrangement 8-3 8-98 10-5 14-18 14-19 16-26 18-32 20-41 22-36 24-31 24-61 B Insert Rotation Shell Size 8 8 10 14 14 16 18 20 22 24 24 Z - - 280 290 - 280 280 280 Explanation: Use P at end of part number for pin contacts in Normal position. Use S at end of part number for socket contacts in Normal position. Use cross reference letters given in chart above for inserts with alternate rotations. 26 Position Z MIL-DTL-38999 Series I Type Connectors with PCB contacts LJTPQ00R wall mounting receptacle (back panel mounting) L MAX S .905 R (TP) .006 .000 M R (TP) S Z PCB TAIL STICKOUT N .062 .001 DIA. FOR SIZE 16 CONTACTS SS V THREAD P .019 .001 DIA. FOR SIZE 20 & 22D CONTACTS T (4 HOLES) HOW TO ORDER * Order by applicable 88/91 part number in table below. 88 prefix designates olive drab cadmium plated connector shell. 91 prefix designates electroless nickel plated connector shell. * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 25 for alternate rotation letter to use. Example part number: 88-569701-35P designates shell size 9 with a 9-35 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. + .005 DIA M Z Shell Size Part Number L Max. M +.000 -.005 N Dia. P Max. Panel Thickness R (TP) S +.011 -.010 T Dia. .005 V Thread Class 2A (Plated) SS Dia. +.000 -.016 Size 16 & 20 Contacts Size 22D Contacts 9 88/91-569701-XXX .453 .820 .572 .234 .719 .938 .128 .4375-28 UNEF .662 .281 - .235 .249 - .188 11 702-XXX .453 .820 .700 .234 .812 1.031 .128 .5625-24 UNEF .810 .281 - .235 .249 - .188 13 703-XXX .453 .820 .850 .234 .906 1.125 .128 .6875-24 UNEF .960 .281 - .235 .249 - .188 15 704-XXX .453 .820 .975 .234 .969 1.219 .128 .8125-20 UNEF 1.085 .281 - .235 .249 - .188 17 705-XXX .453 .820 1.100 .234 1.062 1.312 .128 .9375-20 UNEF 1.210 .281 - .235 .249 - .188 19 706-XXX .453 .820 1.207 .234 1.156 1.438 .128 1.0625-18 UNEF 1.317 .281 - .235 .249 - .188 21 707-XXX .484 .790 1.332 .204 1.250 1.562 .128 1.1875-18 UNEF 1.442 .281 - .235 .249 - .188 23 708-XXX .484 .790 1.457 .204 1.375 1.688 .147 1.3125-18 UNEF 1.567 .281 - .235 .249 - .188 25 709-XXX .484 .790 1.582 .193 1.500 1.812 .147 1.4375-18 UNEF 1.692 .281 - .235 .249 - .188 All dimensions for reference only. 27 MIL-DTL-38999 Series I Type Connectors with PCB contacts LJTPQ00R wall mounting receptacle (back panel mounting) (with clinch nuts) CONNECTOR WITH CLINCH NUTS (4 PLACES) L MAX S .006 .000 .905 R (TP) M Z PCB TAIL STICKOUT R (TP) S N .062 .001 DIA. FOR SIZE 16 CONTACTS T THREAD CLINCH NUT SS V THREAD P .019 .001 DIA. FOR SIZE 20 & 22D CONTACTS HOW TO ORDER * Order by applicable 88/91 part number in table below. 88 prefix designates olive drab cadmium plated connector shell. 91 prefix designates electroless nickel plated connector shell. * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 25 for alternate rotation letter to use. Example part number: 88-628701-35P designates shell size 9 with a 9-35 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. + .005 DIA M Z Shell Size Part Number with Clinch Nuts* L Max. M +.000 -.005 N Dia. P Max. Panel Thickness R (TP) S +.011 -.010 T Thread V Thread Class 2A (Plated) SS Dia. +.000 -.016 Size 16 & 20 Contacts Size 22D Contacts 9 88/91-628701-XXX .453 .820 .572 .234 .719 .938 .112-40UNC-3B .4375-28 UNEF .662 .281 - .235 .249 - .188 11 702-XXX .453 .820 .700 .234 .812 1.031 .112-40UNC-3B .5625-24 UNEF .810 .281 - .235 .249 - .188 13 703-XXX .453 .820 .850 .234 .906 1.125 .112-40UNC-3B .6875-24 UNEF .960 .281 - .235 .249 - .188 15 704-XXX .453 .820 .975 .234 .969 1.219 .112-40UNC-3B .8125-20 UNEF 1.085 .281 - .235 .249 - .188 17 705-XXX .453 .820 1.100 .234 1.062 1.312 .112-40UNC-3B .9375-20 UNEF 1.210 .281 - .235 .249 - .188 19 706-XXX .453 .820 1.207 .234 1.156 1.438 .112-40UNC-3B 1.0625-18 UNEF 1.317 .281 - .235 .249 - .188 21 707-XXX .484 .790 1.332 .204 1.250 1.562 .112-40UNC-3B 1.1875-18 UNEF 1.442 .281 - .235 .249 - .188 23 708-XXX .484 .790 1.457 .204 1.375 1.688 .138-32UNC-3B 1.3125-18 UNEF 1.567 .281 - .235 .249 - .188 25 709-XXX .484 .790 1.582 .193 1.500 1.812 .138-32UNC-3B 1.4375-18 UNEF 1.692 .281 - .235 .249 - .188 All dimensions for reference only. * Consult Amphenol for more information on ordering connectors with clinch nuts. There is also a 3mm clinch nut available (part number 88/91-628401/409) 28 MIL-DTL-38999 Series I Type Connectors with PCB contacts LJTP02R box mounting receptacle (back panel mounting) L MAX. S .905 R (TP) .006 .000 M R (TP) Z PCB TAIL STICKOUT KK N S SS .062 .001 DIA. FOR SIZE 16 CONTACTS .019 .001 DIA. FOR SIZE 20 & 22D CONTACTS P T (4 HOLES) HOW TO ORDER * Order by applicable 88/91 part number in table below. 88 prefix designates olive drab cadmium plated connector shell. 91 prefix designates electroless nickel plated connector shell. * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 25 for alternate rotation letter to use. Example part number: 88-569711-35P designates shell size 9 with a 9-35 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. + .005 DIA M Z Shell Size Part Number L Max. M +.000 -.005 N +.001 -.005 P Max. Panel Thickness R (TP) S +.011 -.010 T Dia. .005 KK Dia. +.006 -.005 SS Dia. +.000 -.016 Size 16 & 20 Contacts Size 22D Contacts 9 88/91-569711-XXX .203 .820 .572 .234 .719 .938 .128 .433 .662 .454 - .401 .468 - .406 11 712-XXX .203 .820 .700 .234 .812 1.031 .128 .557 .810 .454 - .401 .468 - .406 13 713-XXX .203 .820 .850 .234 .906 1.125 .128 .676 .960 .454 - .401 .468 - .406 15 714-XXX .203 .820 .975 .234 .969 1.219 .128 .801 1.085 .454 - .401 .468 - .406 17 715-XXX .203 .820 1.100 .234 1.062 1.312 .128 .926 1.210 .454 - .401 .468 - .406 19 716-XXX .203 .820 1.207 .234 1.156 1.438 .128 1.032 1.317 .454 - .401 .468 - .406 21 717-XXX .234 .790 1.332 .204 1.250 1.562 .128 1.157 1.442 .454 - .401 .468 - .406 23 718-XXX .234 .790 1.457 .204 1.375 1.688 .147 1.282 1.567 .454 - .401 .468 - .406 25 719-XXX .234 .790 1.582 .193 1.500 1.812 .147 1.407 1.692 .454 - .401 .468 - .406 All dimensions for reference only. 29 MIL-DTL-38999 Series I Type Connectors with PCB contacts LJTP02R box mounting receptacle (back panel mounting) (with clinch nuts) CONNECTOR WITH CLINCH NUTS (4 PLACES) L MAX. S .006 .000 .905 R (TP) M R (TP) KK N S T THREAD CLINCH NUT SS Z PCB TAIL STICKOUT .062 .001 DIA. FOR SIZE 16 CONTACTS .019 .001 DIA. FOR SIZE 20 & 22D CONTACTS P HOW TO ORDER * Order by applicable 88/91 part number in table below. 88 prefix designates olive drab cadmium plated connector shell. 91 prefix designates electroless nickel plated connector shell. * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 5-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 25 for alternate rotation letter to use. Example part number: 88-628701-35P designates shell size 9 with a 9-35 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. + .005 DIA M Z Shell Size Part Number with Clinch Nuts L Max. M +.000 -.005 N +.001 -.005 P Max. Panel Thickness R (TP) S +.011 -.010 T Thread KK Dia. +.006 -.005 SS Dia. +.000 -.016 Size 16 & 20 Contacts Size 22D Contacts 9 88/91-628711-XXX .203 .820 .572 .234 .719 1.031 .112-40UNJC-3B .433 .662 .454 - .401 .468 - .406 11 712-XXX .203 .820 .700 .234 .812 1.125 .112-40UNJC-3B .557 .810 .454 - .401 .468 - .406 13 713-XXX .203 .820 .850 .234 .906 1.172 .112-40UNJC-3B .676 .960 .454 - .401 .468 - .406 15 714-XXX .203 .820 .975 .234 .969 1.281 .112-40UNJC-3B .801 1.085 .454 - .401 .468 - .406 17 715-XXX .203 .820 1.100 .234 1.062 1.375 .112-40UNJC-3B .926 1.210 .454 - .401 .468 - .406 19 716-XXX .203 .820 1.207 .234 1.156 1.469 .112-40UNJC-3B 1.032 1.317 .454 - .401 .468 - .406 21 717-XXX .234 .790 1.332 .204 1.250 1.625 .112-40UNJC-3B 1.157 1.442 .454 - .401 .468 - .406 23 718-XXX .234 .790 1.457 .204 1.375 1.750 .138-32UNJC-3B 1.282 1.567 .454 - .401 .468 - .406 25 719-XXX .234 .790 1.582 .193 1.500 1.875 .138-32UNJC-3B 1.407 1.692 .454 - .401 .468 - .406 All dimensions for reference only. * Consult Amphenol for more information on ordering connectors with clinch nuts. There is also a 3mm clinch nut available (part number 88/91-628410/419) 30 MIL-DTL-38999 Series I Type Connectors with PCB contacts LJT07R jam nut receptacle C T .328 MAX. Z PCB TAIL STICKOUT A* N .062 .001 DIA. FOR SIZE 16 CONTACT .019 .001 DIA. FOR SIZE 20 & 22D CONTACTS RR THREAD H V THREAD S .062 MIN. .125 MAX PANEL THICKNESS .915 .005 HOW TO ORDER * Order by applicable 88/91 part number in table below. 88 prefix designates olive drab cadmium plated connector shell. 91 prefix designates electroless nickel plated connector shell. * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 25 for alternate rotation letter to use. Example part number: 88-569721-35P designates shell size 9 with a 9-35 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. * .059 dia. min. 3 lockwire holes. Formed lockwire hole design (6 holes) is optional. "D" shaped mounting hole dimensions Z Shell Size Part Number A* +.000 -.010 C Max. H Hex +.017 -.016 L Max. N +.001 -.005 S .016 T* +.010 -.000 V Thread Class 2A (Plated) RR Thread Class 2A (Plated) Size 16 & 20 Contacts Size 22D Contacts 9 88/91-569721-XXX .669 1.199 .875 .625 .572 1.062 .697 .4375-28 UNEF .6875-24 UNEF .229 - .175 .243 - .182 11 722-XXX .769 1.386 1.000 .625 .700 1.250 .822 .5625-24 UNEF .8125-20 UNEF .229 - .175 .243 - .182 13 723-XXX .955 1.511 1.188 .625 .850 1.375 1.007 .6875-24 UNEF 1.0000-20 UNEF .229 - .175 .243 - .182 15 724-XXX 1.084 1.636 1.312 .625 .975 1.500 1.134 .8125-20 UNEF 1.1250-18 UNEF .229 - .175 .243 - .182 17 725-XXX 1.208 1.761 1.438 .625 1.100 1.625 1.259 .9375-20 UNEF 1.2500-18 UNEF .229 - .175 .243 - .182 19 726-XXX 1.333 1.949 1.562 .656 1.207 1.812 1.384 1.0625-18 UNEF 1.3750-18 UNEF .207 - .158 .221 - .165 21 727-XXX 1.459 2.073 1.688 .750 1.332 1.938 1.507 1.1875-18 UNEF 1.5000-18 UNEF .207 - .158 .221 - .165 23 728-XXX 1.580 2.199 1.812 .750 1.457 2.062 1.634 1.3125-18 UNEF 1.6250-18 UNEF .207 - .158 .221 - .165 25 729-XXX 1.709 2.323 2.000 .750 1.582 2.188 1.759 1.4375-18 UNEF 1.7500-18 UNS .221 - .165 All dimensions for reference only. 31 .207 - .158 MIL-DTL-38999 Series II Type Connectors with PCB contacts JTPQ00R wall mounting receptacle (back panel mounting) .000 .005 .447 S .438 MAX R (TP) SS Z PCB TAIL STICKOUT P PANEL THICKNESS R S (TP) AD .322 T 4 HOLES N .062 .001 DIA. FOR SIZE 16 CONTACTS .019 .001 DIA. FOR SIZES 20 & 22D CONTACTS .000 .005 V THREAD HOW TO ORDER * Order by applicable 88/91 part number in table below. 88 prefix designates olive drab cadmium plated connector shell. 91 prefix designates electroless nickel plated connector shell. * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 25 for alternate rotation letter to use. Example part number: 88-569731-35P designates shell size 8 with a 8-35 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. + .005 DIA M Z Shell Size Part Number N +.001 -.005 P Max. Panel Thickness R (TP) S .016 T Dia. .005 V Thread Class 2A (Plated) AD Dia. .005 SS Dia. +.000 -.016 Size 16 & 20 Contacts Size 22D Contacts .268 - .178 8 88/91-569731-XXX .473 .142 .594 .812 .120 .4375-28 UNEF .516 .563 .257 - .200 10 732-XXX .590 .142 .719 .938 .120 .5625-24 UNEF .633 .680 .257 - .200 .268 - .178 12 733-XXX .750 .142 .812 1.031 .120 .6875-24 UNEF .802 .859 .257 - .200 .268 - .178 14 734-XXX .875 .142 .906 1.125 .120 .8125-20 UNEF .927 .984 .257 - .200 .268 - .178 16 735-XXX 1.000 .142 .969 1.219 .120 .9375-20 UNEF 1.052 1.108 .257 - .200 .268 - .178 18 736-XXX 1.125 .142 1.062 1.312 .120 1.0625-18 UNEF 1.177 1.233 .257 - .200 .268 - .178 20 737-XXX 1.250 .142 1.156 1.438 .120 1.1875-18 UNEF 1.302 1.358 .257 - .200 .268 - .178 22 738-XXX 1.375 .142 1.250 1.562 .120 1.3125-18 UNEF 1.427 1.483 .257 - .200 .268 - .178 24 739-XXX 1.500 .142 1.375 1.688 .147 1.4375-18 UNEF 1.552 1.610 .257 - .200 .268 - .178 All dimensions for reference only. 32 MIL-DTL-38999 Series II Type Connectors with PCB contacts JTP02R box mounting receptacle (back panel mounting) S .505 .000 .447 .005 R (TP) .006 .000 P PANEL THICKNESS Z PCB TAIL STICKOUT R S (TP) AD .322 T 4 HOLES N KK .062 .001 DIA. FOR SIZE 16 CONTACTS .019 .001 DIA. FOR SIZES 20 & 22D CONTACTS .000 .005 L HOW TO ORDER * Order by applicable 88/91 part number in table below. 88 prefix designates olive drab cadmium plated connector shell. 91 prefix designates electroless nickel plated connector shell. * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 25 for alternate rotation letter to use. Example part number: 88-569741-35P designates shell size 8 with a 8-35 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. + .005 DIA M Z Shell Size Part Number L Max. N +.001 -.005 P Max. Panel Thickness R (TP) S .016 T Dia. .005 AD Dia. .005 KK Dia. Max. Size 16 & 20 Contacts Size 22D Contacts 8 88/91-569741-XXX .225 .473 .147 .594 .812 .120 .516 .531 .455 - .403 .466 - .409 10 742-XXX .225 .590 .152 .719 .938 .120 .633 .656 .455 - .403 .466 - .409 12 743-XXX .225 .750 .152 .812 1.031 .120 .802 .828 .455 - .403 .466 - .409 14 744-XXX .225 .875 .152 .906 1.125 .120 .927 .953 .455 - .403 .466 - .409 16 745-XXX .225 1.000 .152 .969 1.219 .120 1.052 1.078 .455 - .403 .466 - .409 18 746-XXX .225 1.125 .152 1.062 1.312 .120 1.177 1.203 .455 - .403 .466 - .409 20 747-XXX .225 1.250 .179 1.156 1.438 .120 1.302 1.328 .455 - .403 .466 - .409 22 748-XXX .225 1.375 .179 1.250 1.562 .120 1.427 1.453 .455 - .403 .466 - .409 24 749-XXX .225 1.500 .169 1.375 1.688 .147 1.552 1.578 .455 - .403 .466 - .409 All dimensions for reference only. 33 MIL-DTL-38999 Series II Type Connectors with PCB contacts JT07R jam nut receptacle S C (2 PLACES) M .094 H + .011 - .010 .062 MIN. .109 MAX. PANEL THICKNESS Z PCB TAIL STICKOUT N .062 .001 DIA. FOR SIZE 16 CONTACTS .019 .001 DIA. FOR SIZES 20 & 22D CONTACTS V THREAD L T* RR THREAD HOW TO ORDER * Order by applicable 88/91 part number in table below. 88 prefix designates olive drab cadmium plated connector shell. 91 prefix designates electroless nickel plated connector shell. * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 25 for alternate rotation letter to use. Example part number: 88-569751-35P designates shell size 8 with a 8-35 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. * .059 dia. min. 3 lockwire holes. Formed lockwire hole design (6 holes) is optional. "D" shaped mounting hole dimensions Z Shell Size Part Number A* +.000 -.010 C Max. H Hex +.017 -.016 L Max. M .005 N +.001 -.005 S .016 T* +.010 -.000 V Thread Class 2A (Plated) RR Thread Class 2A (Plated) Size 16 & 20 Contacts Size 22D Contacts 8 88/91-569751-XXX .830 1.390 1.062 .453 .438 .473 1.250 .884 .4375-28 UNEF .8750-20 UNEF .272 - .200 .283 - .178 10 752-XXX .955 1.515 1.188 .453 .438 .590 1.375 1.007 .5625-24 UNEF 1.0000-20 UNEF .272 - .200 .283 - .178 12 753-XXX 1.084 1.640 1.312 .453 .438 .750 1.500 1.134 .6875-24 UNEF 1.1250-18 UNEF .272 - .200 .283 - .178 14 754-XXX 1.208 1.765 1.438 .453 .438 .875 1.625 1.259 .8125-20 UNEF 1.2500-18 UNEF .272 - .200 .283 - .178 16 755-XXX 1.333 1.953 1.562 .453 .438 1.000 1.781 1.384 .9375-20 UNEF 1.3750-18 UNEF .272 - .200 .283 - .178 18 756-XXX 1.459 2.031 1.688 .453 .438 1.125 1.890 1.507 1.0625-18 UNEF 1.5000-18 UNEF .272 - .200 .283 - .178 20 757-XXX 1.576 2.156 1.812 .422 .464 1.250 2.016 1.634 1.1875-18 UNEF 1.6250-18 UNEF .272 - .200 .283 - .178 22 758-XXX 1.701 2.280 2.000 .422 .464 1.375 2.140 1.759 1.3125-18 UNEF 1.7500-18 UNS .272 - .200 .283 - .178 24 759-XXX 1.826 2.405 2.125 .422 .464 1.500 2.265 1.884 1.4375-18 UNEF 1.8750-16 UN .272 - .200 .283 - .178 All dimensions for reference only. 34 MIL-DTL-38999 Series III Type Connectors with PCB contacts TVP00R wall mounting receptacle (back panel mounting) S 2 PLACES LL R1 M B THREAD 2 PLACES R2 L AA 2 PLACES Z PCB TAIL STICKOUT .062 .001 DIA. FOR SIZE 16 CONTACTS TT 4 PLACES .005 M .019 .001 DIA. FOR SIZE 20 & 22D CONTACTS RED BAND T 4 PLACES BLUE BAND V THREAD 1.240 MAX. HOW TO ORDER * Order by applicable 88/91 part number in table below. 88 prefix designates olive drab cadmium plated connector shell. 91 prefix designates electroless nickel plated connector shell. * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 25 for alternate rotation letter to use. Example part number: 88-569761-35P designates shell size 9 with a 9-35 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. Shell Size Part Number B Thread Class 2A (Plated) 0.1P-0.3L-TS L Max. M +.000 -.005 R1 R2 Composite Series III connectors are available; consult Amphenol, Sidney, NY. S Max. T +.008 -.006 V Thread Metric Designates true position dimensioning Red band indicates fully mated Blue band indicates rear release contact retention system AA Max. LL Panel +.006 Thickness -.000 Z TT +.008 -.006 Size 16 & 20 Contacts Size 22D Contacts 9 88/91-569761-XXX .6250 .469 .820 .719 .594 .948 .128 M12X1-6g .234 .905 .216 .228-.178 .242-.181 11 762-XXX .7500 .469 .820 .812 .719 1.043 .128 M15X1-6g .234 .905 .194 .228-.178 .242-.181 13 763-XXX .8750 .469 .820 .906 .812 1.137 .128 M18X1-6g .234 .905 .194 .228-.178 .242-.181 15 764-XXX 1.0000 .469 .820 .969 .906 1.232 .128 M22X1-6g .234 .905 .173 .228-.178 .242-.181 17 765-XXX 1.1875 .469 .820 1.062 .969 1.323 .128 M25X1-6g .234 .905 .194 .228-.178 .242-.181 19 766-XXX 1.2500 .469 .820 1.156 1.062 1.449 .128 M28X1-6g .234 .905 .194 .228-.178 .242-.181 21 767-XXX 1.3750 .500 .790 1.250 1.156 1.575 .128 M31X1-6g .204 .905 .194 .228-.178 .242-.181 23 768-XXX 1.5000 .500 .790 1.375 1.250 1.701 .154 M34X1-6g .204 .905 .242 .228-.178 .242-.181 25 769-XXX 1.6250 .500 .790 1.500 1.375 1.823 .154 M37X1-6g .204 .905 .242 .228-.178 .242-.181 All dimensions for reference only. 35 MIL-DTL-38999 Series III Type Connectors with PCB contacts TVP00R wall mounting receptacle (back panel mounting) (with clinch nuts) CONNECTOR WITH CLINCH NUTS (4 PLACES) S 2 PLACES LL M B THREAD R 2 PLACES L AA Z PCB TAIL STICKOUT .062 .001 DIA. FOR SIZE 16 CONTACTS T THREAD CLINCH NUT RED BAND .005 M BLUE BAND .019 .001 DIA. FOR SIZE 20 & 22D CONTACTS V THREAD 1.240 MAX. HOW TO ORDER * Order by applicable 88/91 part number in table below. 88 prefix designates olive drab cadmium plated connector shell. 91 prefix designates electroless nickel plated connector shell. * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 25 for alternate rotation letter to use. Example part number: 88-628741-35P designates shell size 9 with a 9-35 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. Shell Size Part Number with Clinch Nuts B Thread Class 2A (Plated) 0.1P-0.3L-TS L Max. M +.000 -.005 Composite Series III connectors are available; consult Amphenol, Sidney, NY. R S Max. T Thread V Thread Metric Designates true position dimensioning Red band indicates fully mated Blue band indicates rear release contact retention system AA Max. LL Panel +.006 Thickness -.000 Z Size 16 & 20 Contacts Size 22D Contacts 9 88/91-628741-XXX .6250 .469 .820 .719 1.094 .112-40UNC-3B M12X1-6g .234 .905 .228-.178 .242-.181 11 742-XXX .7500 .469 .820 .812 1.187 .112-40UNC-3B M15X1-6g .234 .905 .228-.178 .242-.181 13 743-XXX .8750 .469 .820 .906 1.281 .112-40UNC-3B M18X1-6g .234 .905 .228-.178 .242-.181 15 744-XXX 1.0000 .469 .820 .969 1.344 .112-40UNC-3B M22X1-6g .234 .905 .228-.178 .242-.181 17 745-XXX 1.1875 .469 .820 1.062 1.437 .112-40UNC-3B M25X1-6g .234 .905 .228-.178 .242-.181 19 746-XXX 1.2500 .469 .820 1.156 1.531 .112-40UNC-3B M28X1-6g .234 .905 .228-.178 .242-.181 21 747-XXX 1.3750 .500 .790 1.250 1.625 .112-40UNC-3B M31X1-6g .204 .905 .228-.178 .242-.181 23 748-XXX 1.5000 .500 .790 1.375 1.750 .138-32UNC-3B M34X1-6g .204 .905 .228-.178 .242-.181 25 749-XXX 1.6250 .500 .790 1.500 1.875 .138-32UNC-3B M37X1-6g .204 .905 .228-.178 .242-.181 All dimensions for reference only. * Consult Amphenol for more information on ordering connectors with clinch nuts. 36 MIL-DTL-38999 Series III Type Connectors with PCB contacts TVP02R box mounting receptacle S 2 PLACES R1 L BLUE BAND 2 PLACES R2 ZZ RED BAND 2 PLACES .062 .001 DIA. FOR SIZE 16 CONTACTS .019 .001 DIA. FOR SIZES 20 & 22D CONTACTS .005 M TT 4 PLACES T 4 PLACES B THREAD Z PCB TAIL STICKOUT AA M LL HOW TO ORDER * Order by applicable 88/91 part number in table below. 88 prefix designates olive drab cadmium plated connector shell. 91 prefix designates electroless nickel plated connector shell. * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 25 for alternate rotation letter to use. Example part number: 88-569771-35P designates shell size 9 with a 9-35 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. Shell Size Part Number B Thread Class 2A (Plated) 0.1P-0.3L-TS L Max. M +.000 -.005 R1 R2 Composite Series III connectors are available; consult Amphenol, Sidney, NY. S Max. T +.008 -.006 AA Max. Panel Thickness Designates true position dimensioning Red band indicates fully mated Blue band indicates rear release contact retention system Z LL +.006 -.000 TT +.008 -.006 Size 16 & 20 Contacts Size 22D Contacts 9 88/91-569771-XXX .6250 .205 .820 .719 .594 .948 .128 .234 .905 .216 .460-.375 .471-.399 11 772-XXX .7500 .205 .820 .812 .719 1.043 .128 .234 .905 .194 .460-.375 .471-.399 13 773-XXX .8750 .205 .820 .906 .812 1.137 .128 .234 .905 .194 .460-.375 .471-.399 15 774-XXX 1.0000 .205 .820 .969 .906 1.232 .128 .234 .905 .173 .460-.375 .471-.399 17 775-XXX 1.1875 .205 .820 1.062 .969 1.323 .128 .234 .905 .194 .460-.375 .471-.399 19 776-XXX 1.2500 .205 .820 1.156 1.062 1.449 .128 .234 .905 .194 .460-.375 .471-.399 21 777-XXX 1.3750 .235 .790 1.250 1.156 1.575 .128 .204 .905 .194 .460-.375 .471-.399 23 778-XXX 1.5000 .235 .790 1.375 1.250 1.701 .154 .204 .905 .242 .460-.375 .471-.399 25 779-XXX 1.6250 .235 .790 1.500 1.375 1.823 .154 .204 .905 .242 .460-.375 .471-.399 All dimensions for reference only. 37 MIL-DTL-38999 Series III Type Connectors with PCB contacts TVP02R box mounting receptacle (with clinch nuts) CONNECTOR WITH CLINCH NUTS (4 PLACES) S 2 PLACES L BLUE BAND R 2 PLACES RED BAND .062 .001 DIA. FOR SIZE 16 CONTACTS .019 .001 DIA. FOR SIZES 20 & 22D CONTACTS T THREAD CLINCH NUT Z PCB TAIL STICKOUT B THREAD AA M .005 M .162 - .072 FOR SIZE 16 & 20 CONTACTS .142 .022 FOR SIZE 22D CONTACTS LL HOW TO ORDER * Order by applicable 88/91 part number in table below. 88 prefix designates olive drab cadmium plated connector shell. 91 prefix designates electroless nickel plated connector shell. * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 25 for alternate rotation letter to use. Example part number: 88-628751-35P designates shell size 9 with a 9-35 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. Shell Size Part Number with Clinch Nuts B Thread Class 2A (Plated) 0.1P-0.3L-TS L Max. M +.000 -.005 Composite Series III connectors are available; consult Amphenol, Sidney, NY. Designates true position dimensioning Red band indicates fully mated Blue band indicates rear release contact retention system R S Max. T Thread AA Max. Panel Thickness Z LL +.006 -.000 Size 16 & 20 Contacts Size 22D Contacts 9 88/91-628751-XXX .6250 .205 .820 .719 1.031 .112-40UNC-3B .234 .905 .460-.375 .471-.399 11 752-XXX .7500 .205 .820 .812 1.125 .112-40UNC-3B .234 .905 .460-.375 .471-.399 13 753-XXX .8750 .205 .820 .906 1.172 .112-40UNC-3B .234 .905 .460-.375 .471-.399 15 754-XXX 1.0000 .205 .820 .969 1.281 .112-40UNC-3B .234 .905 .460-.375 .471-.399 17 755-XXX 1.1875 .205 .820 1.062 1.375 .112-40UNC-3B .234 .905 .460-.375 .471-.399 19 756-XXX 1.2500 .205 .820 1.156 1.469 .112-40UNC-3B .234 .905 .460-.375 .471-.399 21 757-XXX 1.3750 .235 .790 1.250 1.562 .112-40UNC-3B .204 .905 .460-.375 .471-.399 23 758-XXX 1.5000 .235 .790 1.375 1.750 .138-32UNC-3B .204 .905 .460-.375 .471-.399 25 759-XXX 1.6250 .235 .790 1.500 1.875 .138-32UNC-3B .204 .905 .460-.375 .471-.399 All dimensions for reference only. * Consult Amphenol for more information on ordering connectors with clinch nuts. 38 MIL-DTL-38999 Series III Type Connectors with PCB contacts TV07R jam nut receptacle .378 MAX. PANEL THICKNESS .062 MIN. .125 MAX. C BLUE BAND Z PCB TAIL STICKOUT .062 .001 DIA. FOR SIZE 16 CONTACTS .019 .001 DIA. FOR SIZES 20 & 22D CONTACTS B THREAD RED BAND V THREAD H S 2 PLACES 1.280 MAX. HOW TO ORDER * Order by applicable 88/91 part number in table below. 88 prefix designates olive drab cadmium plated connector shell. 91 prefix designates electroless nickel plated connector shell. * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 25 for alternate rotation letter to use. Example part number: 88-569781-35P designates shell size 9 with a 9-35 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. Composite Series III connectors are available; consult Amphenol, Sidney, NY. Red band indicates fully mated Blue band indicates rear release contact retention system .059 dia. min. 3 lockwire holes. Formed lockwire hole design (6 holes) is optional. * "D" shaped mounting hole dimensions Z Shell Size Part Number A* +.000 -.000 B Thread Class 2A (Plated) 0.1P-0.3L-TS C Max. H Hex +.017 -.016 S .010 T +.010 -.000 V Thread Metric Size 16 & 20 Contacts Size 22D Contacts 9 88/91-569781-XXX .669 .6250 1.199 .875 1.062 .697 M12X1-6g .244 - .200 .258 - .206 11 782-XXX .769 .7500 1.386 1.000 1.250 .822 M15X1-6g .244 - .200 .258 - .206 13 783-XXX .955 .8750 1.511 1.188 1.375 1.007 M18X1-6g .244 - .200 .258 - .206 15 784-XXX 1.084 1.0000 1.636 1.312 1.500 1.134 M22X1-6g .244 - .200 .258 - .206 17 785-XXX 1.208 1.1875 1.761 1.438 1.625 1.259 M25X1-6g .244 - .200 .258 - .206 19 786-XXX 1.333 1.2500 1.949 1.562 1.812 1.384 M28X1-6g .222 - .177 .236 - .180 21 787-XXX 1.459 1.3750 2.073 1.688 1.938 1.507 M31X1-6g .222 - .177 .236 - .180 23 788-XXX 1.575 1.5000 2.199 1.812 2.062 1.634 M34X1-6g .222 - .177 .236 - .180 25 789-XXX 1.709 1.6250 2.323 2.000 2.188 1.759 M37X1-6g .222 - .177 .236 - .180 All dimensions for reference only. 39 Stand-off Adapter for use with 38999 PCB connectors Amphenol's stand-off adapter and spanner nut assembly allows any MIL-DTL38999 jam nut receptacle to support PCB contacts and may eliminate the need for special stand-off shell design. Consult Amphenol for more information. Tri-Start MIL-DTL-38999 Jam Nut Connector with Stand-off Adapter SPANNER NUT ADAPTER R (TP) 45 TYP E A J DIA. R (TP) V THREAD L C DIA. 4 HOLES #6-32 UNC-2B THREAD (PLATED) +.001 .250 -.001 B DIA. .002 M F HOW TO ORDER Order by Shell Size 9 E J Dia. L V Thread Metric Plated .200 .625 .150 M12X1-6H .200 .744 .150 M15X1-6H Part Number A .003 B Dia. .003 C Dia. XP10-611901-09G 1.062 1.188 .750 11 XP10-611901-11G 1.250 1.375 .900 13 XP10-611901-13G 1.375 1.500 .975 .862 M18X1-6H 15 XP10-611901-15G 1.500 1.625 1.125 1.019 M22X1-6H 17 XP10-611901-17G 1.625 1.750 1.250 1.137 M25X1-6H 19 XP10-611901-19G 1.812 1.938 1.375 1.255 M28X1-6H 21 XP10-611901-21G 1.938 2.062 1.469 1.373 M31X1-6H 23 XP10-611901-23G 2.062 2.188 1.625 1.492 M34X1-6H 25 XP10-611901-25G 2.188 2.312 1.750 1.610 M37X1-6H All dimensions for reference only. 40 MIL-C-26482 Series 1 Type Connectors with PCB contacts PT02 box mounting receptacle L S 4 HOLES .120 .005 DIA. (.147 .005 DIA. SIZE 24) R (TP) R (TP) S .030 .001 DIA. FOR SIZE 16 & 20 CONTACTS M A N K Z PCB TAIL STICKOUT HOW TO ORDER * Order by applicable 71 part number in table below. 71 prefix designates olive drab cadmium plated connector shell. (For availability of other finishes consult Amphenol, Sidney, NY) * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 26 for alternate rotation letter to use. Example part number: 71-570121-98P designates shell size 8 with a 8-98 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. Shell Size 6 (MMC) located within .0025 of (TP) Z +.040 -.050 Part Number A +.001 -.005 K +.021 -.010 L Max. M +.010 -.000 N Dia. Max. R (TP) S +.011 -.010 Size 16 & 20 Contacts 71-570120-XXX .348 .493 .825 .431 .323 .469 .688 .380 8 71-570121-XXX .473 .493 .825 .431 .449 .594 .812 .380 10 71-570122-XXX .590 .493 .825 .431 .573 .719 .938 .380 12 71-570123-XXX .750 .493 .825 .431 .699 .812 1.031 .380 14 71-570124-XXX .875 .493 .825 .431 .823 .906 1.125 .380 16 71-570125-XXX 1.000 .493 .825 .431 .949 .969 1.219 .380 18 71-570126-XXX 1.125 .493 .825 .431 1.073 1.062 1.312 .380 20 71-570127-XXX 1.250 .650 1.076 .556 1.199 1.156 1.438 .286 22 71-570128-XXX 1.375 .650 1.076 .556 1.323 1.250 1.562 .286 24 71-570129-XXX 1.500 .683 1.109 .589 1.449 1.375 1.688 .253 All dimensions for reference only. 41 MIL-C-26482 Series 1 Type Connectors with PCB contacts PT07 jam nut receptacle S M H K .030 .001 DIA. FOR SIZE 16 & 20 CONTACTS J S A R THREAD P Z PCB TAIL STICK OUT HOW TO ORDER * Order by applicable 71 part number in table below. 71 prefix designates olive drab cadmium plated connector shell. (For availability of other finishes consult Amphenol, Sidney, NY) * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 26 for alternate rotation letter to use. Example part number: 71-533721-98P designates shell size 8 with a 8-98 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. P Panel Thickness Part Number A Dia. +.001 -.005 H +.017 -.016 J Flat +.000 -.010 K +.011 -.010 M .010 Min. 6 71-533720-XXX .348 .625 .405 .125 .696 8 71-533721-XXX .473 .750 .530 .125 .696 10 71-533722-XXX .590 .875 .655 .125 12 71-533723-XXX .750 1.062 .818 14 71-533724-XXX .875 1.188 .942 16 71-533725-XXX 1.000 1.312 18 71-533726-XXX 1.125 1.438 20 71-533727-XXX 1.250 22 71-533728-XXX 24 71-533729-XXX Shell Size All lockwire holes are .044 dia. min. Z +.025 -.035 Max. R Thread Class 2A S .010 Size 16 & 20 Contacts .062 .125 .4375-28 UNEF .812 .376 .062 .125 .5625-24 UNEF .938 .376 .696 .062 .125 .6875-24 UNEF 1.062 .376 .125 .696 .062 .125 .8750-20 UNEF 1.250 .376 .125 .696 .062 .125 1.0000-20 UNEF 1.375 .376 1.066 .125 .696 .062 .125 1.1250-18 UNEF 1.500 .376 1.191 .125 .696 .062 .125 1.2500-18 UNEF 1.625 .376 1.562 1.316 .156 .884 .062 .250 1.3750-18 UNEF 1.812 .367 1.375 1.688 1.441 .156 .884 .062 .250 1.5000-18 UNEF 1.938 .367 1.500 1.816 1.566 .156 .917 .062 .250 1.6250-18 UNEF 2.062 .334 All dimensions for reference only. 42 MIL-5015 Type Connectors with PCB contacts MS3102R box mounting receptacle S A THREAD R B Z PCB TAIL STICKOUT R S N .030 .001 DIA. FOR SIZE 16 CONTACTS T 4 HOLES M L K HOW TO ORDER * Order by applicable 10- part number in table below. 10- prefix designates olive drab cadmium plated connector shell. (For availability of other finishes consult Amphenol, Sidney, NY) * Add insert arrangement to end of number. Refer to insert availability chart on page 4 and pin-out illustrations on pages 4-24. Last letter of part number designates rotation; P for pins in normal position, S for sockets in normal position. See page 26 for alternate rotation letter to use. Example part number: 10-602462-3P designates shell size 10SL with a 10SL-3 insert and pin contacts in normal position. * Z dimension is determined by contact type in the insert arrangement. * Most common options are shown; other options are available. Shell Size Part Number A Thread Class 2A B Min. Full Thread K +.020 -.010 L +.000 -.010 M +.010 -.000 N Dia. +.010 -.000 Reverse Bayonet GT Series connectors that incorporate 5015 inserts can also be supplied with printed circuit board contacts. Consult Amphenol for more information. R .005 S .031 T Dia. +.004 -.002 Z .045 Size 16 Contacts 8S 10-602460-XXX .5000-28 UNEF .391 .672 .297 .562 .375 .594 .875 .120 .188 10S 461-XXX .6250-24 NEF .391 .672 .297 .562 .500 .719 1.000 .120 .188 10SL 462-XXX .6250-24 NEF .391 .672 .297 .562 .625 .719 1.000 .120 .188 12S 463-XXX .7500-20 UNEF .450 .672 .297 .562 .625 .812 1.094 .120 .188 12 464-XXX .7500-20 UNEF .625 .860 .484 .750 .625 .812 1.094 .120 .188 14S 465-XXX .8750-20 UNEF .450 .672 .297 .562 .750 .906 1.188 .120 .188 14 466-XXX .8750-20 UNEF .625 .860 .484 .750 .750 .906 1.188 .120 .188 16S 467-XXX 1.0000-20 UNEF .450 .672 .297 .562 .875 .969 1.281 .120 .188 16 468-XXX 1.0000-20 UNEF .625 .860 .484 .750 .875 .969 1.281 .120 .188 18 469-XXX 1.1250-18 NEF .625 .891 .453 .750 1.000 1.062 1.375 .120 .188 20 470-XXX 1.2500-18 NEF .625 .891 .453 .750 1.125 1.156 1.500 .120 .188 22 471-XXX 1.3750-18 NEF .625 .891 .453 .750 1.250 1.250 1.625 .120 .188 24 472-XXX 1.5000-18 NEF .625 .953 .453 .812 1.375 1.375 1.750 .147 .188 28 473-XXX 1.7500-18 NS .625 .953 .453 .812 1.625 1.562 2.000 .147 .188 32 474-XXX 2.0000-18 NS .625 1.031 .438 .875 1.875 1.750 2.250 .173 .188 36 475-XXX 2.2500-16 UN .625 1.031 .438 .875 2.062 1.938 2.500 .173 .188 40 476-XXX 2.5000-16 UN .625 1.031 .438 .875 2.312 2.188 2.750 .173 .188 All dimensions for reference only. 43 Universal Header Assemblies for flex print or PCB connectors Mounts to all MIL-DTL-38999 and MIL-C-26482 Connectors The use of connectors with printed circuit termination is rapidly gaining popularity due to the use of high volume, vapor phase or wave solder manufacturing processes. Termination of this style of connector to flex print or a printed circuit board represents a major cost in the manufacturing process for users. When adding flex or printed circuit board assemblies to an expensive filter or filter/transient protection connector, the total cost of a failed solder joint, a bent pin, or an unanticipated electrical failure becomes prohibitive. The universal header assembly from Amphenol will provide for easy separation of the connector from the board on these occasions. Headers provide easy separation of the connector from the PC board. Header Assemblies Provide Cost Savings Incorporation of the header assembly provides the user with time and cost saving potentials. These header assemblies can be vapor phase or wave soldered to flex or printed circuit boards prior to the receipt of the EMI/EMP connector. Headers can be installed to standard connectors, allowing for electrical testing that would adversely affect the sensitive diodes, MOV's or capacitors in the EMI/EMP connectors. Expensive connector assemblies can be easily removed from and reattached to the header assembly as the manufacturing process dictates. Cylindrical Configuration * * * * * Mounting Applications 3 PCB stickout dimensions are available. Size 22D contacts use .175 thick headers Size 16 contacts use .195 thick headers Consult Amphenol for Size 20 contact use with headers. Headers for cylindrical connectors accommodate up to 128 pins. Consult Amphenol catalogs for mating connector contact layouts (12-092 and 12-090 for MIL-DTL-38999 and 12-070 for MIL-C-26482). Mounting to Rectangular ARINC Connectors Shell modifications are recommended, but are not necessary. The header assembly can be attached to connectors with standard flange placement or directly to the circuit board. The ideal application would involve either a single flange moved all the way to the rear of the connector or a double flange. Cinch nuts can be installed in either flange to allow easier mounting to the panel or the header assembly. The forward flange would mount the connector to the panel; the rear flange would be used to mount the header assembly. Various types of captivated or loose attaching screws can be utilized for unique applications. Amphenol universal headers are slotted to allow mounting to all series of MIL-DTL-38999 or MIL-C-26482 connectors without special alterations. They are of similar dimension as the flange of the mounting connector and would be approximately .185 inches (4.70 mm) thick. * Headers for ARINC connector arrangements accommodate up to 150 pins. * Consult Amphenol for ARINC configurations and detailed dimensions. Materials * Body is molded from Torlon or PPS (Polyphenylene Sulfide) * Electrical engagement areas of the header contact are plated with .00003 inches minimum of gold over .00005 inches minimum of nickel. Incorporates a Shorter Pin/Socket Contact The heart of the header assembly is a short pin/socket contact. The tall of the contact would accommodate standard throughhole diameter and thickness of the flex or printed circuit board materials. The socket is imbedded in the molded material, making electrical engagement with the printed circuit tail of the connector. 44 Universal Header Assemblies for flex print or PCB connectors, cont. The drawing below shows the standard universal adapter for use with MIL-DTL-38999 and MIL-C-26482 connectors. Consult Amphenol, Sidney, NY for drawings of headers for ARINC configurations. S R1 VISUAL INDICATOR NOTCH FOR TOP CL OF INSERT PATTERN (SIZE & CONFIGURATION OPTIONAL) R2 T G SIZE 22 CONTACT VIEW .020 .001 TT F RADIUS Assembly Part Number 21-904008-XX( ) 21-904010-XX( ) 21-904012-XX( ) 21-904014-XX( ) 21-904016-XX( ) 21-904018-XX( ) 21-904020-XX( ) 21-904022-XX( ) 21-904024-XX( ) Shell Size 8/9 10/11 12/13 14/15 16/17 18/19 20/21 22/23 24/25 F Radius G .005 .094 .094 .094 .125 .125 .125 .125 .125 .125 See Suffix Chart TP designates true position dimensioning. S .005 T +.008 -.006 R1 TP R2 TP TT +.008 -.006 .938 1.031 1.125 1.219 1.312 1.438 1.562 1.688 1.812 .128 .128 .128 .128 .128 .128 .128 .154 .154 .719 .812 .906 .969 1.062 1.156 1.250 1.375 1.500 .594 .719 .812 .906 .969 1.062 1.156 1.250 1.375 .216 .194 .194 .173 .194 .194 .194 .242 .242 Assemblies containing Size 22 contact only: .175 Assemblies containing Size 16 or 20 contacts: .195 HOW TO ORDER INFORMATION For Universal Adapter used with MIL-DTL-38999 and MIL-C-26482 Connectors XX - XX Shell Size Designation* X 08 10 12 14 16 18 20 22 24 Designates Amphenol(R) Interface Adapter Shell size designation for MIL-DTL-38999 Series I, II, III and IV or MIL-C-26482 Series 1 and 2. See suffix chart. Arrangement number - See MIL-STD-1560 or MIL-STD-1669. Also consult Amphenol catalogs 12-092 (MIL-DTL-38999 Series III), 12-090 (MIL-DTL-38999 Series I, II), and 12-070 (MIL-C-26482 Series 1) Contact PCB Stickout designation See suffix chart. * For how to order information on adapters to be used with ARINC connectors, consult Amphenol Aerospace, Sidney NY. 45 SIZE 16 AND 20 CONTACT VIEW B PCB STICKOUT (SEE SUFFIX CHART BELOW) .050 .040 .001 (SIZE 20) .0625 .0010 (SIZE 16) G NOTE: Size 22 accepts .018 to .022 dia. PCB tails. Size 16 accepts .048 to .064 dia. PCB tails. Size 20 accepts .037 to .043 dia. PCB tails. ASSEMBLY NUMBER SUFFIX CHART Use coded number as follows: 21-9040 B PCB STICKOUT (SEE SUFFIX CHART BELOW) Arrangement Number Suffix*** Insert Arrangement Suffix from MIL-STD-1560 or MIL-STD-1669 Contact PCB Stickout** Suffix B .015 Stickout 1 2 3 .120 .185 .270 Shell size designation for MIL-DTL-38999 Series I, II, III & IV and MIL-C-26482 Series 1 and 2. Examples: Shell size 9 use 08. Shell size 25 use 24. ** Size 22 contacts available in all 3 stickout lengths. Size 16 and 20 contacts available only in .185 and .270 lengths. *** Insert arrangement 14-97 and 15-97 are not available at this time. Consult Amphenol, Sidney, NY for information. Additional Products for PCB Application Amphenol rectangular interconnects (R) Amphenol is also a leader in rectangular interconnects for printed circuit board application. Within the rectangular families of Amphenol interconnects are Low Mating Force MIL-C-55302 connectors and LRM Surface Mount Connectors. 1 2 3 Variety of Low Mating Force Rectangular Connectors including styles with fiber optics (right) and small styles with only 10 contacts (upper left). LOW MATING FORCE MIL-C-55302 CONNECTORS * Superior electrical characteristics - redundant current paths, low constrictive resistance, stable time/life contact resistance, uniform current densities * High performance polyester dielectric moldings * Over 20,000 mating cycles with B3 Bristle Brush Bunch(R) contacts * Significant reduction in mating force. Only 1.5 ounce max contact engaging and separating forces * -65 to +125C temperature rating * High circuit count interconnections to 400 contacts per connector * Two, three and four row patterns, 10 to 100 contacts per row, in one contact per row increments * 0.100 in. center to center contact spacing, square grid * Serviceability - removable crimp contacts, repairable PC stud and solder less wrap contacts * Board support structure - reinforcing reduced * Variety of contact terminations and platings * Accessories to suit latching, piloting and polarization variations * Up to 256 keyed mating polarizations M55302/166 or 167 Mother Board, M55302/170 Daughter Board 1., 2. Two piece PCB connector featuring PCB stud or solderless wrap contacts in the MB Series and field repairable 90 PCB stud contacts in the DB Series. 4 M55302/169 Input/Output 3. Rear release, rear removable crimp contacts for discrete wire cabling. I/O connector series mates with standard MB and PC receptacle series to provide external inputs/outputs. M55302/168 PC 4. 90 PCB stud contacts for side mounting on board. Mates with DB and I/O series. Hybrid Rectangular Connectors with Brush/Power/Coax/Fiber Optic Combinations Amphenol offers wide versatility of combining contact types in rectangular interconnects. For more information on Low Mating Force Connectors see catalog 12-035 online at www.amphenol-aerospace.com 46 Additional Products for PCB Application Amphenol rectangular interconnects, cont. (R) LRM SURFACE MOUNT CONNECTORS The introduction of high speed integrated circuitry such as VHSIC and MMIC has enabled the Design Engineer to accomplish far more on his printed circuit board than ever before. This, coupled with the emergence of a revolutionary change in avionics packaging - modular avionic architectures - has created the need for a high performance, low insertion force PCB connector with significantly increased contact density. The LRM (Line Replaceable Module) connector series are high performance, high density interconnects, specifically designed to connect printed circuit boards. The Amphenol Brush contact technology is the foundation of the LRM connector series. LRM Connectors with Staggered Grid * Advanced design to provide high contact density for high speed integrated circuitry in SEM-E and custom form factors * 180 contact insert pattern grid in 8 rows: 0.100 inch spacing along the row with 0.050 inch between rows, rows offset 0.050 inch. * Options include various shell designs to accommodate a wide range of PC board/heat sink combinations * Solder tail, wire wrap or compliant contact availability * ESD protection LRM Connectors with GEN-X Grid * Higher contact density and improved electrical performance * All the features of the 180 contact pattern, including ESD protection * Available in SEM-E and custom form factors * 236 contact pattern grid in 8 rows: 0.075 inch spacing along the row with 0.060 inch between rows, rows offset 0.0375 inch LRM Staggered Grid Airflow-thru Connectors * Available for wider boards up to 0.425 inch. These accommodate standard brush tails in staggered pattern, but with increased spacing in the center, and they also provide more airflow cooling of inserts. LRM Connectors with Many Contact and Shell Design Options Flexibility to meet customer demands that include: combinations of brush and fiber optics; options for high speed contacts, RF contacts, or new high amperage RADSOK(R) contacts; incorporation of flex circuits; custom shells with multiple bays. For more information on LRM Connectors see new catalog 12-037 at website www.amphenol-aerospace.com. BACKPLANE ASSEMBLIES Amphenol is the leading manufacturer of custom backplane assemblies using high density, ruggedized, board-to-board backplane interconnects. These can incorporate brush contacts, pc tail, or press-fit compliant pin contacts, or fiber optic termini. They also can incorporate fork and blade contacts (see next page for fork and blade contact connectors). * Electrical Backplanes - Large panel sizes with high layer counts, and features such as high aspect ratio plating, small diameter plated-through holes, and controlled impedances. * Optical Backplanes - Fiber termination with Multi-Terminal (MT) optical ferrules. Ribbon cable sorting allows programming flexibility; thus rendering the entire system easily upgradeable. * Hybrid Optical Backplanes - Integrated electrical and optical systems in one discreet package for advanced avionics systems. For more information on Backplane Assemblies from Amphenol Backplane Systems division, see publication SL-392 at websites: www.amphenol-abs.com or www.amphenol-aerospace.com. 47 From top to bottom: Staggered Grid, 2 Bay LRM; GEN-X Grid, 2 Bay LRM; LRM inserts with RADSOK contacts; LRM insert with MT ferrule fiber optics and brush contacts in a Differential Pair insert. LRM Module Inserts (showing front and back of inserts) with PC Tails in Staggered Grid Pattern Backplane Assembly with LRM Connectors with Brush Contacts on one side and Cylindrical Connectors with Press-fit Compliant Contacts on the other. Amphenol (R)Rectangular Interconnects additional products for PCB application UHD MODULE/BACKPLANE CONNECTORS WITH FORK & BLADE CONTACTS Amphenol's wide range of board level interconnects also includes high density UHD Series module and backplane connectors. These use the staggered grid pattern but do not use brush contacts. The staggered grid pattern is 80 contacts per inch, .025 pitch in 8 rows. They are SEM-E format and are qualified to: EIA 15-763, DESC 89065, IEEE 1101.1 to 1101.9. The UHD module connectors have surface mount blade contacts and the mating UHD backplane connectors have solderless press-fit tuning fork contacts. There are a wide range of high contact density patterns and the length and style can be tailored to meet customer requirements. They are rigid pin terminated to the board or flex terminated to the board. Coax, fiber optics and power contacts can also be integrated into the connector configuration. Other options include EMI shielding and UHD interconnects can be provided in a stacking configuration. NAFI SERIES WITH FORK & BLADE CONTACTS Amphenol NAFI daughtercard and backplane connectors are another board level interconnect that uses the fork and blade contact termination. They provide a wide range of medium contact density patterns and meet MIL-C-28754 standards. Daughtercard termination is through-hole, using nickel/gold solder plated contacts. The mating interface is a blade contact which can be either parallel or perpendicular to the daughtercard. They are available with 2, 3, 4 and 5 rows of contacts, .100 x .100 pitch. They can be rigid pin terminated to the board or flex circuitry can be used to attach to the board. Both UHD and NAFI interconnects are used in military and commercial aviation, in space applications, shipboard and in military vehicles. For more information see catalog 12-036 at www.amphenol-abs.com or www.amphenol-aerospace.com. UHD Backplane Connectors on Board, Rigid Pin Termination, with Fiber Optics, Coax or Power Contacts NAFI Daughtercard Connector with Flex Termination PRINTED CIRCUIT BOARD TERMINAL BLOCKS Amphenol Pcd division supplies wire-to-board discrete-wire connections in a variety of styles. * Pluggable terminal blocks and headers in 3.5mm/.150" pitches in straight, angled, with locking ears, 2-tier, 3 tier, and low profile styles. * Fixed terminal blocks in 5.0mm, .200", .250", .375" pitches in standard profiles, multi-tier, spring-clamp, high current and high voltage styles. * Edgecard connectors that are screw terminated style in different size pitches. * Custom designed terminal blocks with ear mounting options, DIN-rail mounting options, and others. WIRING INTERFACE MODULES Amphenol Pcd also supplies an industrial board level interconnect that replaces discrete terminations with a single pluggable unit. Connectors can be D-Sub, ribbon cable, RJ style, Centronic or DIN types. Also diodes, LEDs, resistors, capacitors, relays or fuses can be included in the unit. For more information on terminal blocks and wiring interface modules go online to www.amphenol-pcd.com. 48 PCB Circuit Board Terminal Blocks and Wiring Interface Modules (R) Amphenol Cylindrical Connectors for Printed Circuit Board Applications 12-170-2 This catalog has been specifically designed to assist in the critical process of selecting the right cylindrical connector for a printed circuit board application. Contact arrangements have been carefully selected to guide designers to the most commonly available and widely used insert patterns. Pin-out location illustrations of these contact insert patterns are shown first, followed by connector shell drawings in three series: MIL-DTL-38999, MIL-C-26482, MIL-5015. Proven & reliable cylindrical connector solutions for PC board attachment: MIL-DTL-38999, MIL-C-26482 and MIL-5015, with a wide range of contact arrangements and options Amphenol Corporation Amphenol Aerospace 40-60 Delaware Avenue, Sidney, New York 13838-1395 Phone: 800-678-0141 or 607-563-5011 Fax: 607-563-5157 www.amphenol-aerospace.com Amphenol For more information on the wide variety of PC tail contacts that are offered by Amphenol, see catalog 12-130, High Frequency Contacts, which also includes coax, twinax, triax and quadrax shielded contacts. 17 10 25 32 4 40 1 47 53 55 52 3 9 16 24 31 39 46