TYPE 418P Polyester Capacitors Filmite "E", ORANGE DROP, Radial Lead PERFORMANCE CHARACTERISTICS Operating Temperature: - 55C to + 85C, standard; up to + 105C when WVDC is reduced to 70% of + 85C rating. To + 125C when WVDC is 50% of + 85C rating. Insulation Resistance: After a 2 minute charge at rated voltage or 500 V, whichever is less: At + 25C: 100,000 Megohm for C < .25 Microfarads. 25,000 Megohm - Microfarads for C > .25 Microfarads. At + 85C: 10,000 Megohm for C < .15 Microfarads. 1500 Megohm - Microfarads for C > .15 Microfarads. At + 105C: 1500 Megohm for C < .17 Microfarads. 250 Megohm - Microfarads for C > .17 Microfarads. At + 125C: 200 Megohm for C < .13 Microfarads. 25 Megohm - Microfarads for C > .13 Microfarads. Capacitance, Tolerance and Dissipation Factor: Capacitance shall be measured at a frequency of 1000Hz @ + 25C or else be referred to measurements made at that frequency and temperature. The maximum dissipation factor shall be .75%. A COMPANY OF Vay SPRAGUE Vv FEATURES * Identical performance characteristics to Type 225P pressed polyester capacitors through 600 WVDC ratings Wound from PETP polyester film and thin gauge foil under carefully controlled atmospheric conditions * Protected against moisture by a conformal coating of epoxy * Specifically designed for printed wiring board applications Widely used in computers, instrumentation and telecommunications equipment Dielectric Withstanding Voltage: Capacitors rated below 1000 volts shall withstand a DC potential of 250% of rated voltage applied between terminals for not more than 5 seconds. Capacitors rated 1000 volts and above shall withstand a DC potential of 200% of rated voltage applied between the terminals for not more than 5 seconds. The test voltage must be applied and discharged through a resistor of 1 ohm per volt. Humidity Test: Condition capacitors with no voltage applied for 72 hours @ 95% relative humidity and + 75C. Remove capacitors from humidity chamber, wipe surface dry of moisture and dry in circulating air for 4 hours. Measure insulation resistance after a 2 minute charge @ + 25C and rated voltage or 500 VDC, whichever is less. Minimum product of insulation resistance and capacitance shall be 5000 Megohm - Microfarads after test but need not exceed 10,000 Megohm. Not more than one failure allowed in 12 units tested. DC Life Test: Capacitors are capable of withstanding a 500 hour life test @ + 85C @ 150% of rated working voltage. After test, capacitance shall not have changed by more than 5% of initial value, insulation resistance shall not have decreased by more than 50% of the initial limit and dissipation factor shall not have increased to more than 1%. L D | Max. < ~| Max. rt \ x Bote a 0.237 Y 0.237 ita s.r rere 131,780) Lead A Lead A Min. Length Length < A | _ . 0.032 [0.813] Dia. (No. 20 AWG) >| Ss << Tinned Copper-Clad Steel + .060 (1.524] + 030 [0.762] + .030 [0.762] Terminal A Terminal B Terminal D Ss CASE L CODE (Max.) Terminal A and B Terminal D J 0.70 [17.78] 0.500 [12.700] 0.375 [9.525] K 0.90 [22.86] 0.688 [17.475] 0.375 [9.525] L 4.20 [30.48] 0.969 [24.613] 0.719 [18.263] M 1.60 [40.64] 1.344 [34.138] 1.094 [27.788] SPRAGUE, 678 Main Street, Sanford, ME 04073-0231 * Phone (207) 490-7236 - Ceramic, Orange Drop, Wrap and Fill Film, Foil, Miniature Aluminum * Phone (207) 490-7243 - Aluminum, Wrap and Fill Metalized Film, Motor Starts * Fax 207-490-3906 43 D 24F MM 8514812 OO21bSb 608TYPE 418P 16 1.5 Z 14 3 12 N i 10 3 g CAPACITANCE CHANGE ENVELOPE s 1.0 < 8 FOR 96% CONFIDENCE LEVEL = B 2 \ [rreicat | / = 2 Bs a # S| __ S55 -40 -25 0 +25 +50 +75 +85 +105 +125 O56 ~40 -25 0 +25 +50 +75 +85 +105 +125 -50 +100 -50 +100 TEMPERATURE DEG. CENTIGRADE TEMPERATURE DEG. CENTIGRADE SIZE +10% TOLERANCE PART NUMBER L D 100 VDC/70 VAC 0.027 418P27391J 0.70 [17.78] 0.35 [8.89] 0.033 418P33391J 0.70 [17.78] 0:35 [8.89] 0.047 418P473914 0.70 [17.78] 0.35 [8.89] 0.082 418P82391K 0.90 [22.86] 0.40 [10.16] 0.1 418P10491K 0.90 [22.86] 0.40 [10.16] 0.15 418P15491K 0.90 [22.86] 0.45 [11.43] 0.22 418P22491L 1.20 [30.48] 0.45 [11.43] 0.33 418P33491L 1.20 [30.48] 0.50 [12.70] 0.47 418P47491M 1.60 [40.64] 0.50 [12.70] 0.68 418P68491M 1.60 [40.64] 0.60 [15.24] 1.0 418P10591M 1.60 [40.64] 0.70 [17.78] 200 VDC/140 VAC 0.0056 418P56292J 0.70 [17.78] 0.33 [8.38] 0.0068 418P68292J 0.70 [17.78] 0.33[8.38] 0.01 418P10392J 0.70 [17.78] 0.33 [8.38] 0.015 418P15392J 0.70 [17.78] 0.33 [8.38] 0.018 418P18392J 0.70 [17.78] 0.33 [8.38] 0.022 418P22392J 0.70 [17.78] 0.33 [8.38] 0.033 418P33392K 0.90 [22.86] 0.38 [9.65] 0.039 418P39392K 0.90 [22.86] 0.38 [9.65] 0.047 418P47392K 0.90 [22.86] 0.38 [9.65] 0.056 418P56392L 1.20 [30.48] 0.38 [9.65] 0.068 418P68392L 1.20 [30.48] 0.38 [9.65] 0.082 418P82392L 1.20 [30.48] 0.40 [10.16] 0.1 418P10492L 1.20 [30.48] 0.40 [10.16] 0.15 418P15492L 1.20 [30.48] 0.45 [11.43] 0.22 418P22492L 1.20 [30.48] 0.50 [12.70] 0.27 418P27492M 1.60 [40.64] 0.47 [11.94] 0.33 418P33492M 1.60 [40.64] 0.47 [11.94] 0.47 418P47492M 1.60 [40.64] 0.55 [13.97] * These standard ratings are available through Sprague distribution on special order. For complete Part Number, add letter and number for terminal and lead length in accordance with How to Order (Ex: 418P47492MD3). ** 6OHz rms. SPRAGUE, 678 Main Street, Sanford, ME 04073-0231 * Phone (207) 490-7236 - Ceramic, Orange Drop, Wrap and Fill Film, Foil; Miniature Aluminum 44 * Phone (207) 499-7943 - Aluminum. Wrap and Fill Metalized Film, Motor Starts * Fax 207-490-3906 D CoF 6514ahe OO2L65? Suy myTYPE 418P + 10% TOLERANCE PART NUMBER L D 400 VDC/200 VAC** 0.001 418P 10294) 0.70 [17.78] 0.30 [7.62] 0.0015 418P15294J 0.70 [17.78] 0.30 [7.62] 0.0022 418P22294) 0.70 [17.78] 0.30 [7.62] 0.0033 418P33294J 0.70 [17.78] 0.30 [7.62] 0.0047 418P47204J 0.70 [17.78] 0.30 [7.62] 0.0068 418P68294J 0.70 [17.78] 0.33 [8.38] 0.0082 418P822045 0.70 [17.78] 0.35 [8.89] 0.01 418P10394J 0.70 [17.78] 0.35 (8.89] 0.015 418P 15394) 0.70 [17.78] 0.38 [9.65] 0.018 418P18394K 0.90 [22.86] 0.38 [9.65] 0.022 418P22394K 0.90 [22.86] 0.38 [9.65] 0.033 418P33394K 0.90 [22.86] 0.40 [10.16] 0.047 418P47394L 1.20 [30.48] 0.40 [10.16] 0.056 418P563904L 1.20 [30.48] 0.45 [11.43] 0.068 418P68304L 1.20 [30.48] 0.45 [11.43] 0.082 418P82394L 1.20 [30.48] 0.62 [13.21] 0.1 418P10494L 1.20 [30.48] 0.52 [13.21] 0.15 418P15494L 1.20 [30.48] 0.57 [14.48] 0.18 418P18494M 1.60 [40.64] 0.60 [15.24] 0.22 418P22494M 1.60 [40.64] 0.60 [15.24] 0.27 418P27494M 1.60 [40.64] 0.65 [16.51] 0.33 418P33494M 1.60 [40.64] 0.65 [16.51] 0.39 418P39494M 1.60 [40.64] 0.72 [18.29] 0.47 418P47494M 1.60 [40.64] 0.80 [20.32] 600 VDC/200 VAC 0.001 41BP10296J 0.70 [17.78] 0.30 [7.62] 0.0012 418P12296J 0.70 [17.78] 0.33 [8.38] 0.0015 418P15296J 0.70 [17.78] 0.33 [8.38] 0.0018 418P18296J 0.70 [17.78] 0.33 [8.38] 0.0022 418P22296J 0.70 [17.78] 0.33 [8.38] 0.0027 418P27296J 0.70 [17.78] 0.35 [8.89] 0.0033 418P33296J 0.70 [17.78] 0.35 [8.89] 0.0039 418P39296J 0.70 [17.78] 0.38 [9.65] 0.0047 418P47296) 0.70 [17.78] 0.38 {9.65] 0.0056 418P56296J 0.70 [17.78] 0.40 [10.16] 0.0068 418P68296) 0.70 [17.78] 0.40 [10.16] 0.0082 418P82296K 0.90 [22.86] 0.40 [10.16] 0.01 418P10396K 0.90 [22.86] 0.40 [10.16] 0.012 418P12396K 0.90 [22.86] 0.40 [10.16] 0.015 418P15396K 0.90 [22,86] 0.40 [10.16] 0.018 418P18396K 0.90 [22.86] 0.45 [11.43] 0.022 418P22396K 0.90 [22.86] 0.45 [11.43] 0.027 418P27396L 1.20 [30.48) 0.45 [11.43] 0.033 418P33396L 1.20 [30.48] 0.45 [11.43] 0.039 418P39396L 1.20 [30.48] 0.55 [13.97] 0.047 418P47396L 1,20 [30.48] 0.55 [13.97] 0.056 418PS6396L 1.20 [30.48] 0.60 [15.24] 0.068 418P68396L 1.20 [30.48] 0.60 [15.24] 0.082 418P82396L 1.20 [30.48] 0.65 [16.51] 04 418P10496L 1.20 [30.48] 0.65 [16.51] 0.12 418P12496M 1.60 [40.64] 0.70 [17.78] 0.15 418P15496M 1.60 [40.64] 0.70 [17.78] 0.18 418P18496M 1.60 [40.64] 0.80 [20.32] 0.22 418P22496M 1.60 [40.64] 0.80 [20.32] 0.25 418P25496M 1.60 [40.64] 0.80 [20.32] * These standard ratings are available through Sprague distribution on special order. For complete Part Number, add letter and number for terminal and lead length in accordance with How to Order (Ex: 418P47492MD3). ** 6OHzZ rms. SPRAGUE, 678 Main Street, Sanford, ME 04073-0231 Phone (207) 490-7236 - Ceramic, Orange Drop, Wrap and Fill Film, Foil, Miniature Aluminum * Phone (207) 490-7243 - Aluminum, Wrap and Fill Metalized Film, Motor Starts Fax 207-490-3906 C4F MM 4514812 00216546 460 Mw DTYPE 418P +10% TOLERANCE PART NUMBER L D 1000 VDC/200 VAC** 0.001 418P102910J 0.70 [17.78} 0.33 [8.38] 0.0015 418P152910J 0.70 [17.78] 0.33 [8.38] 0.0018 418P182910d 0.70 [17.78] 0.35 [8.89] 6.0022 418P222910J 0.70 [17.78] 0.35 [8.89] 0.0033 418P332910K 0.90 [22.86] 0.35 [8.89] 0.0047 418P472910K 0.90 [22.86] 0.40 [10.16] 0.0056 418P562910K 0.90 [22.86] 0.43 [10.92] 0.0068 418P682910K 0.90 [22.86] 0.43 [10.92] 0.0082 418P822910K 0.90 [22.86] 0.48 [12.19] 0.01 418P103910K 0.90 [22.86] 0.48 [12.19] 0.015 418P153910L 1.20 [30.48] 0.48 [12.19] 0.018 418P183910L 1.20 [30.48] 0.58 [14.73] 0.022 418P223910L 1.20 [30.48] 0.58 [14.73] 0.027 418P273910L 1.20 [30.48] 0.65 [16.51} 0.033 418P333910L 1.20 [30.48} 0.65 [16.51] 0.039 418P393910M 1.60 [40.64] 0.65 [16.51] 0.047 418P473910M 1.60 [40.64] 0.65 [16.51] 0.056 418P563910M 4.60 [40.64] 0.75 [19.05] 0.068 418P683910M 1.60 [40.64] 0.75 [19.05] 0.082 418P823910M 1.60 [40.64] 0.85 [21.59] 0.1 418P104910M 1.60 [40.64] 0.85 [21.59] * These standard ratings are available through Sprague distribution on special order. For complete Part Number, add fetter and number for terminal and lead length in accordance with How to Order (Ex: 418P47492MD3). ** 6OHz rms. conform to Decade Rating for the tolerance specified. 418P 104 9 1 J, K, L or M. D 3 (-XXX) TYPE CAPACITANCE TOLERANCE DC VOLTAGE CASE CODE TERMINAL LEAD LENGTH SPECIAL RATING , CONSTRUCTION 0=+ 20% See Dimensional 1 = 0.187"'+ 0.030" 9=+ 10% Configurations. [4.750 + 0.762) 5=+5% 2 = 0.250" + 0.030" [6.350 + 0.762] 3 =.1.250" [31.750] Minimum Capacitance is expressed This is A= Straight Lead A three-digit suffix in picofarads. The first two expressed in B = Hairpin Crimped may be added by digits are significant. The hundreds of D = Hockey Crimped the factory to third is the number of zeros volts. denote special to fallow. Values must construction. SPRAGUE, 678 Main Street, Sanford, ME 04073-0231 Phone (207) 490-7236 - Ceramic, Orange Drop, Wrap and Fill Film, Foil, Miniature Aluminum * Phone (207) 490-724 - Aluminum, Wrap and Fill Metalized Film, Motor Starts : Fax 207-490-3906 _D 24F MM 8534812 0021659 317 46