USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller PRODUCT FEATURES Datasheet General Description Features The SMSC USB4640/USB4640i is a Hi-Speed HSIC USB hub and card reader combo solution with an upstream port that is compliant to HSIC 1.0 (supplement to the USB 2.0 Specification). The two downstream ports are compliant with the USB 2.0 Specification. High-Speed Inter-Chip (HSIC) is a digital interconnect bus that enables the use of USB technology as a low-power chip-to-chip interconnect at speeds up to 480 Mb/s. The HSIC interface is an industry standard 2-pin digital interface which uses standard USB software. The USB4640/USB4640i provides an ultra fast interface between an HSIC enabled host and several popular flash media formats. The controller allows read/write capability to flash media from the following families: -- -- -- -- Secure DigitalTM (SD) MultiMediaCardTM (MMC) Memory Stick(R) (MS) xD-Picture CardTM (xD)1 The USB4640/USB4640i combo solution leverages SMSC's innovative technology that delivers industryleading data throughput in mixed-speed USB environments. Average sustained transfer rates exceeding 35 MB/s are possible2. -- Configures internal code using an external I2C EEPROM -- Supports external code using an SPI Flash EEPROM -- Customizable vendor ID, product ID, and language ID if using an external EEPROM Highlights Upstream HSIC port and 2 exposed Hi-Speed USB 2.0 downstream ports for external peripheral expansion Dedicated flash media reader internally attached to a 3rd downstream port of the hub as a USB compound device -- single or multiplexed flash media reader interface -- Up to 9 configurable GPIOs for special functions The USB4640 supports the commercial temperature range of 0C to +70C The USB4640i supports the industrial temperature range of -40C to +85C 48-pin QFN (7 x 7 mm) lead-free, RoHS compliant package PortSwap -- Programmable USB differential-pair pin locations ease PCB design by aligning USB signal lines directly to connectors -- Flexible port mapping and disable sequencing PortMap Compliance with the following flash media card specifications SD 2.0; MMC 4.2; MS 1.43; MSPro 1.02; MS-Pro-HG 1.01; MS-Duo 1.10; and xD 1.2 Low-power digital HSIC interface offers a replacement for onboard host and device connection for analog USB bus cable HSIC interface enables printers, mobile PCs, ultramobile PCs, and cell phone products to reduce the total power budget HSIC interface provides use of USB connectivity and compatibility with existing USB drivers and software External 1.2 V reference allows upstream/downstream HSIC links to use the same voltage reference Supports a single external 3.3 V supply source; internal regulators provide 1.8 V internal core voltage for additional bill of materials and power savings The hub transaction translator (TT) supports Full-Speed and Low-Speed peripheral operation 9 KB RAM | 64 KB on-chip ROM Enhanced EMI rejection and ESD protection performance Hub and flash media reader/writer configuration from a single source: PHYBoost -- Programmable USB signal drive strength for recovering signal integrity using 4-level driving strength resolution Applications 1. Obtain user license from the xD-Picture Card License Office. 2. Host and media dependent. SMSC USB4640/USB4640i 3G/4G handsets, smartphones, cell phones, and other mobile devices Desktop and mobile PCs Printers GPS navigation systems Media players/viewers Consumer A/V Set-top boxes Industrial products DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Order Number(S): USB4640/USB4640i-HZH for 48-PIN, QFN LEAD-FREE RoHS COMPLIANT PACKAGE USB4640/USB4640i-HZH-TR for 48-PIN, QFN LEAD-FREE RoHS COMPLIANT TAPE AND REEL PACKAGE THIS PRODUCT MEETS THE HALOGEN MAXIMUM CONCENTRATION VALUES PER IEC61249-2-21. FOR ROHS COMPLIANCE AND ENVIRONMENTAL INFORMATION, PLEASE VISIT WWW.SMSC.COM/ROHS. 80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123 Copyright (c) 2011 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC's website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation ("SMSC"). Product names and company names are the trademarks of their respective holders. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Revision 1.3 (05-17-11) 2 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Conventions Within this manual, the following abbreviations and symbols are used to improve readability. Example BIT FIELD.BIT x...y BITS[m:n] PIN zzzzb 0xzzz zzh rsvd N/A code Multi Word Name Section Name VAL x <Parameter> {,Parameter} [Parameter] SMSC USB4640/USB4640i Description Name of a single bit within a field Name of a single bit (BIT) in FIELD Range from x to y, inclusive Groups of bits from m to n, inclusive Pin Name Binary number (value zzzz) Hexadecimal number (value zzz) Hexadecimal number (value zz) Reserved memory location. Must write 0, read value indeterminate Not applicable Instruction code, or API function or parameter Used for multiple words that are considered a single unit, such as: Resource Allocate message, or Connection Label, or Decrement Stack Pointer instruction. Section or Document name. Over-bar indicates active low pin or register bit Don't care <> indicate a Parameter is optional or is only used under some conditions Braces indicate Parameter(s) that repeat one or more times. Brackets indicate a nested Parameter. This Parameter is not real and actually decodes into one or more real parameters. 3 DATASHEET Revision 1.3 (05-17-11) Industrial Temperature USB 2.0 Flash Media Controller and Hub Combo Datasheet Table of Contents Chapter 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.1 1.2 1.3 Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Software Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 OEM Selectable Hub Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Chapter 2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Chapter 3 Pinning Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.1 3.2 3.3 3.4 3.5 3.6 3.7 Pin Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-Pin List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Buffer Type Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port Power Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5.1 Port Power Control Using a USB Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5.2 Port Power Control Using a Poly Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ROM BOOT Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 12 13 18 20 20 20 21 22 Chapter 4 Configuration Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.1 4.2 4.3 4.4 4.5 Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Card Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.1 EEPROM/SPI Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.2 EEPROM Data Descriptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Flash Media Controller Extended Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.1 EEPROM Data Descriptor Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.2 A0h-A7h: Device Power Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.3 Device ID Strings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.4 Hub Controller Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.5 Internal Flash Media Controller Extended Configurations . . . . . . . . . . . . . . . . . . . . . . . . 4.4.6 I2C EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.7 In-Circuit EEPROM Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Default Configuration Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5.1 External Hardware nRESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5.2 USB Bus Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 25 25 25 26 28 29 33 35 36 46 46 47 47 47 48 Chapter 5 AC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 5.1 5.2 5.3 Oscillator/Crystal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ceramic Resonator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.1 I2C EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3.2 USB 2.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 50 50 50 50 Chapter 6 DC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 6.1 6.2 6.3 6.4 Maximum Guaranteed Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 52 53 56 Chapter 7 GPIO Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Revision 1.3 (05-17-11) 4 DATASHEET SMSC USB4640/USB4640i Industrial Temperature USB 2.0 Flash Media Controller and Hub Combo Datasheet Chapter 8 Package Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 8.1 Tape and Reel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 SMSC USB4640/USB4640i 5 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet List of Tables Table 3.1 Table 3.2 Table 3.3 Table 3.4 Table 3.5 Table 4.1 Table 4.2 Table 4.3 Table 4.4 Table 4.5 Table 4.6 Table 4.7 Table 5.1 Table 6.1 Table 7.1 USB4640/USB4640i 48-Pin List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB4640/USB4640i Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB4640/USB4640i Buffer Type Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Legend for Pin Reset States Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB4640/USB4640i Reset States Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Flash Media Controller Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hub Controller Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other Internal Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Flash Media Controller Extended Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . Port Map Register for Ports 1 and 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port Map Register for Port 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . nRESET Timing for EEPROM Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Crystal Circuit Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB4640/USB4640i GPIO Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision 1.3 (05-17-11) 6 DATASHEET 12 13 18 23 23 26 27 28 28 44 45 48 49 56 57 SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet List of Figures Figure 2.1 Figure 3.1 Figure 3.2 Figure 3.3 Figure 3.4 Figure 3.5 Figure 3.6 Figure 3.7 Figure 4.1 Figure 5.1 Figure 5.2 Figure 5.3 Figure 6.1 Figure 8.1 Figure 8.2 Figure 8.3 USB4640/USB4640i Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB4640/USB4640i 48-Pin QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port Power Control with USB Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Port Power Control with a Single Poly Fuse and Multiple Loads . . . . . . . . . . . . . . . . . . . . . Port Power with Ganged Control with Poly Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI ROM Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I2C Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . nRESET Timing for EEPROM Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Typical Crystal Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Capacitance Formulas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ceramic Resonator Usage with SMSC IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply Rise Time Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB4640/USB4640i 48-Pin QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-Pin Package Tape Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-Pin Package Reel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SMSC USB4640/USB4640i 7 DATASHEET 10 11 20 21 21 22 22 22 47 49 49 50 52 58 59 60 Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Chapter 1 Overview The USB4640/USB4640i is a Hi-Speed HSIC USB hub and card reader combo solution with an upstream port compliant to the High-Speed Inter-Chip USB Electrical Specification Revision 1.0 [2]. The two downstream ports are USB 2.0 compliant, and the dedicated flash media reader/writer is internally attached to a 3rd downstream port as a USB compound device. High-Speed Inter-Chip (HSIC) is a digital interconnect bus that enables the use of USB technology as a low-power chip-to-chip interconnect at speeds up to 480 Mb/s (see the High-Speed Inter-Chip USB Electrical Specification Revision 1.0). This combo solution supports several multi-format flash media cards. This multi-format flash media controller and USB hub combo features two exposed downstream USB ports available for external peripheral expansion. The USB4640/USB4640i can attach to an upstream port as a Full- or Full/Hi-Speed hub. The hub supports Low-Speed, Full-Speed, and Hi-Speed downstream devices (if operating as a Hi-Speed hub) on all of the enabled downstream ports. All required resistors on the USB ports are integrated into the hub, including all series termination resistors on D+ and D- pins and all required pull-down and pull-up resistors. The over-current sense inputs for the downstream facing ports have internal pull-up resistors. The USB4640/USB4640i includes programmable features, such as: PortMap: provides flexible port mapping and disable sequences. The downstream ports of a USB4640/USB4640i hub can be reordered or disabled in any sequence to support multiple platform designs with minimum effort. For any port that is disabled, the USB4640/USB4640i hub controllers automatically reorder the remaining ports to match the USB host controller's port numbering scheme. PortSwap: adds per-port programmability to USB differentialpair pin locations. PortSwap also allows direct alignment of USB signals (D+/D-) to connectors to avoid uneven trace length or crossing of the USB differential signals on the PCB. PHYBoost: enables 4 programmable levels of USB signal drive strength in downstream port transceivers. PHYBoost will also attempt to restore USB signal integrity. Note: PHYBoost is only available on the two USB downstream ports. 1.1 Hardware Features Single chip HSIC hub and flash media controller combo USB2660/USB2660i supports the commercial temperature range of 0C to +70C USB4640/USB4640i supports the industrial temperature range of -40C to +85C Transaction translator (TT) in the hub supports operation of FS and LS peripherals Full power management with individual or ganged power control of each downstream port Optional support for external firmware access via SPI interface Onboard 24 MHz crystal driver circuit Optional external 24 MHz clock input (must be a 1.8 V signal) Code execution via SPI ROM which must meet the following criteria: --30 MHz or 60 MHz operation support --Single bit or dual bit mode support --Mode 0 or mode 3 SPI support Revision 1.3 (05-17-11) 8 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 1.2 Compliance with the following flash media card specifications: --Secure Digital 2.0 and MultiMediaCard 4.2 -SD 2.0, SD-HS, SD-HC -TransFlashTM and reduced form factor media -1/4/8 bit MMC 4.2 --Memory Stick 1.43 --Memory Stick Pro Format 1.02 --Memory Stick Pro-HG Duo Format 1.01 -Memory Stick, MS Duo, MS-HS, MS Pro-HG, MS Pro --Memory Stick Duo 1.10 -xD-Picture Card 1.2 Up to 9 GPIOs: configuration and polarity for special function use --The number of actual GPIOs depends on the implementation configuration used --One GPIO available with up to 200 mA drive and protected fold-back short circuit current 8051 8-bit microprocessor --60 MHz - single cycle execution --64 KB ROM | 9 KB RAM Integrated regulator for 1.8 V core operation Software Features 1.3 Hub and flash media reader/writer configuration from a single source: External I2C ROM or external SPI ROM, where the following features are then available: --Customizable vendor ID, product ID, and device ID --12-hex digits maximum for the serial number string --28-character manufacturer ID and product strings for the flash media reader/writer OEM Selectable Hub Features The USB4640/USB4640i provides a default configuration that may be sufficient for most applications. following a reset. The USB4640/USB4640i can instead be configured by an external I2C EEPROM or SPI ROM. Compound Device support on a port-by-port basis --a port is permanently hardwired to a downstream USB peripheral device Select over-current sensing and port power control on an individual or ganged (all ports together) basis to match the OEM's choice of circuit board component selection Port power control and over-current detection/delay features Configure the delay time for filtering the over-current sense inputs Configure the delay time for turning on downstream port power Bus- or self-powered selection Hub port disable or non-removable configurations Flexible port mapping and disable sequencing supports multiple platform designs Programmable USB differential-pair pin location eases PCB layout by aligning USB signal lines directly to connectors Programmable USB signal drive strength recovers USB signal integrity using 4 levels of signal drive strength Indicate the maximum current that the 2-port hub consumes Indicate the maximum current required for the hub controller SMSC USB4640/USB4640i 9 DATASHEET Revision 1.3 (05-17-11) Revision 1.3 (05-17-11) 3.3 V DATASHEET 10 USB Data Downstream PHY PLL 24 MHz Crystal Transaction Translator Serial Interface Engine 1.8 V Reg 3.3 V 1.8 V USB Data OC Sense/ Downstream Pwr Switch PHY Port #2 OC Sense Switch Driver Routing & Port Re-Ordering Logic Repeater HSIC HSIC Data & Strobe OC Sense/ Pwr Switch Port #3 OC Sense Switch Driver VDDCR 1.8 V Reg HSIC Impedance 1.2 V SIE CTL 3K total BUS INTFC ADDR MAP EP2 EP2 RX RX EP2 TX RAM EP0 TX EP0 RX ROM 64 K RAM 6K SFR RAM BUS INTFC GPIOs GPIO PWR_FET0 SPI MS BUS INTFC SD/ MMC/ SDIO FMI FMDU CTL AUTO_CBW PROC Flash Media Cards (require Combo socket) xD* XDATA BRIDGE + BUS ARBITER Program Memory I/O Bus 8051 PROCESSOR *For xD-Picture CardTM support, please obtain a user license from the xD-Picture Card License office. BRIDGE Port Controller Controller Serial Interface 8 pins GPIO10 (CRD_PWR) SPI (4 pins) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Chapter 2 Block Diagram Figure 2.1 USB4640/USB4640i Block Diagram SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Chapter 3 Pinning Information This chapter outlines the pinning configuration, followed by a corresponding pin list grouped by function. The detailed pin descriptions are listed then outlined in Section 3.3, on page 13. GPIO2/RXD GPIO10 (CRD_PWR) VDD33 SD_D2/xD_D5 SD_D3/MS_D3/xD_D6 GPIO12/MS_INS SD_D4/MS_D2/xD_D7 GPIO14/xD_nCD xD_nB/R xD_nRE xD_nCE VDD33 36 35 34 33 32 31 30 29 28 27 26 25 Pin Configurations GPIO1/LED/TXD 37 24 SD_CMD/MS_D0/xD_CLE nRESET 38 23 SD_D5/MS_D1/xD_ALE HSIC_IMP 39 22 xD_nWE TEST 40 21 SD_CLK/MS_BS/xD_nWP 20 SD_D6/MS_D7/xD_D0 19 SD_D7/MS_D6/xD_D1 18 SD_D0/MS_D4/xD_D2 17 SD_D1/MS_D5/xD_D3 16 VDD33 15 CRFILT 14 GPIO15/SD_nCD 13 GPIO6/SD_WP/MS_SCLK/xD_D4 10 11 12 SPI_DI VDD33 9 SPI_CLK/GPIO4/SCL SPI_DO/GPIO5/SDA/SPI_SPD_SEL 8 USBDN_DM2 SPI_CE_n 48 7 47 1 RBIAS VDD33 Ground Pad (must be connected to VSS) 6 46 PRTCTL3 PLLFILT PRTCTL2 45 5 44 4 XTAL2 XTAL1 (CLKIN) VDD33 43 USBDN_DP3 HSIC_STROBE SMSC USB4640/40i (Top View QFN-48) 3 42 USBDN_DM3 41 2 VDD12 HSIC_DAT USBDN_DP2 3.1 Indicates pins on the bottom of the device. Figure 3.1 USB4640/USB4640i 48-Pin QFN SMSC USB4640/USB4640i 11 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 3.2 48-Pin List Table 3.1 USB4640/USB4640i 48-Pin List UPSTREAM HSIC INTERFACE (3 PINS) HSIC_IMP HSIC_DAT HSIC_STROBE DOWNSTREAM USB INTERFACE (3 PINS) XTAL1 (CLKIN) XTAL2 RBIAS DOWNSTREAM 2-PORT USB INTERFACE (6 PINS) USBDN_DP2 USBDN_DM2 USBDN_DP3 USBDN_DM3 PRTCTL2 PRTCTL3 SECURE DIGITAL/MEMORY STICK/xD INTERFACE (18 PINS) SD_D7/ MS_D6/ xD_D1 SD_D6/ MS_D7/ xD_D0 SD_D5/ MS_D1/ xD_ALE SD_D4/ MS_D2/ xD_D7 SD_D3/ MS_D3/ xD_D6 SD_D2/ xD_D5 SD_D1/ MS_D5/ xD_D3 SD_D0/ MS_D4/ xD_D2 SD_CLK/ MS_BS/ xD_nWP SD_CMD/ MS_D0/ xD_CLE GPIO15/ SD_nCD GPIO12/ MS_INS GPIO6/ SD_WP/ MS_SCLK/ xD_D4 GPIO14/ xD_nCD xD_nWE xD_nB/R xD_nRE xD_nCE SPI INTERFACE (4 PINS) SPI_CE_N SPI_DO/ GPIO5/ SDA/ SPI_SPD_SEL SPI_CLK/ GPIO4/ SCL SPI_DI MISC (5 PINS) nRESET TEST GPIO1/ LED/ TXD GPIO2/ RXD CRFILT PLLFILT GPIO10 (CRD_PWR) POWER (9 PINS) (6) VDD33 VDD12 TOTAL 48 Revision 1.3 (05-17-11) 12 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 3.3 Pin Descriptions This section provides a detailed description of each pin. The pins are arranged in functional groups according to their associated interface. The pin descriptions below are applied when using the internal default firmware and can be referenced in Chapter 4: Configuration Options on page 25. See Appendix A: (Acronyms) on page 61 for details. An n in the signal name indicates that the active (asserted) state occurs when the signal is at a low voltage level. When the n is not present, the signal is asserted when it is at a high voltage level. The terms assertion and negation are used exclusively in order to avoid confusion when working with a mixture of active low and active high signals. The term assert, or assertion, indicates that a signal is active, independent of whether that level is represented by a high or low voltage. The term negate, or negation, indicates that a signal is inactive. Table 3.2 USB4640/USB4640i Pin Descriptions SYMBOL 48-PIN QFN BUFFER TYPE DESCRIPTION UPSTREAM HSIC INTERFACE HSIC_IMP 39 I HSIC Impedance Control Selects the driver impedance of HSIC_DAT and HSIC_STROBE 1 : Approximately 50 impedance 0 : Approximately 40 impedance HSIC_DAT 42 I/O HSIC Data Bi-directional double data rate (DDR) data signal that is synchronous to the HSIC_STROBE signal as defined in the High-Speed Inter-Chip USB Specification, Version 1.0. HSIC_STROBE 43 I/O HSIC Strobe Bi-directional data strobe signal defined in the High-Speed Inter-Chip USB Specification, Version 1.0. DOWNSTREAM USB INTERFACE USBDN_DM [3:2] USBDN_DP [3:2] 3 1 4 2 I/O-U PRTCTL[3:2] 7 6 I/OD6PU USB Bus Data Connect to the downstream USB bus data signals and can be swapped using the PortSwap feature (See Section 4.4.4.20: F1h: Port Swap on page 43). USB Power Enable, when used as an: RBIAS 47 I-R output: enables power to downstream USB peripheral devices and have weak internal pull-up resistors. (See Section 3.5: Port Power Control on page 20 for diagram and usage instructions.) input: monitor the over-current condition (when the power is enabled). When an over-current condition is detected, the pins turn the power off. USB Transceiver Bias Sets the transceiver's internal bias currents using a 12.0 k, 1.0% resistor attached from VSS. XTAL1 (CLKIN) 45 ICLKx 24 MHz Crystal Input or External Clock Input Can be connected to one terminal of the crystal or connected to an external 24 MHz clock when a crystal is not used. SMSC USB4640/USB4640i 13 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Table 3.2 USB4640/USB4640i Pin Descriptions (continued) SYMBOL 48-PIN QFN BUFFER TYPE XTAL2 44 OCLKx DESCRIPTION 24 MHz Crystal Output The other terminal of the crystal, or it is left open when an external clock source is used to drive XTAL1(CLKIN). SECURE DIGITAL INTERFACE SD_D[7:0] SD_CLK 19 20 23 30 32 33 17 18 I/O8PU 21 O8 Secure Digital Data 7-0 Bi-directional data signals SD_D0 - SD_D7 with weak pull-up resistors. Secure Digital Clock The output clock signal to the SD/MMC device. SD_CMD 24 I/O8PU Secure Digital Command Bi-directional signal that connects to the CMD signal of the SD/MMC device. The bi-directional signal has a weak internal pull-up resistor. GPIO15/ 14 I/O6 General Purpose IO 15 Can be used either as an input; edge sensitive interrupt input; or output. Custom firmware is required to activate this function. SD_nCD I/O8PU Secure Digital Card Detect GPIO Designated by the default firmware as the Secure Digital card detection pin and has an internal pull-up. GPIO6/ 13 I/O6 General Purpose IO 6 Can be used either as input; edge sensitive interrupt input; or output. Custom firmware is required to activate this function. SD_WP I/O8 Secure Digital Write Protected GPIO Designated by the default firmware as the Secure Digital card interface mechanical write protect detect pin. MEMORY STICK INTERFACE MS_BS 21 O8 Memory Stick Bus State Connected to the bus state pin of the MS device. It is used to control the Bus States 0, 1, 2, and 3 (BS0, BS1, and BS3) of the MS device. GPIO12/ 31 I/O8 General Purpose IO 12 Can be used either as input; edge sensitive interrupt input; or output. Custom firmware is required to activate this function. MS_INS IPU Memory Stick Card Insertion GPIO Designated by the default software as the Memory Stick card detection pin and has a weak internal pull-up resistor. MS_SCLK 13 O8 Memory Stick System Clock Output clock signal to the MS device. Revision 1.3 (05-17-11) 14 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Table 3.2 USB4640/USB4640i Pin Descriptions (continued) SYMBOL MS_D[7:0] 48-PIN QFN BUFFER TYPE 20 19 17 18 32 30 23 24 I/O8PD DESCRIPTION Memory Stick System Data In/Out Bi-directional data signals for the MS device. In serial mode, the most significant bit (MSB) of each byte is transmitted first by either the memory stick controller MSC or the MS device on MS_D0. MS_D0, MS_D2, and MS_D3 have weak pull-down resistors. MS_D1 has a pull-down resistor when in parallel mode. Otherwise, it is disabled. In 4- or 8-bit parallel modes, all MS_D7 - MS_D0 signals have weak pull-down resistors. xD-PICTURE CARD INTERFACE xD_D[7:0] xD_ALE 30 32 33 13 17 18 19 20 I/O8PD 23 O8PD xD-Picture Card Data 7-0 Bi-directional data signals xD_D7 - xD_D0 and have weak internal pull-down resistors. xD-Picture Card Address Strobe Active high Address Latch Enable (ALE) signal for the xD-Picture Card device. This pin has a weak pull-down resistor that is permanently enabled. xD_nB/R 28 IPU xD-Picture Card Busy or Data Ready Connected to the BSY/RDY pin of the xD-Picture Card device. When using the internal FET, this pin has a weak internal pull-up resistor that is tied to the output of the internal power FET. If an external FET is used (the internal FET is disabled), then the internal pull-up is not available (an external pull-up is required). xD_nCE 26 O8PU xD-Picture Card Chip Enable Active low chip enable signal for the xD-Picture Card device. When using the internal FET, this pin has weak internal pull-up resistor that is tied to the output of the internal power FET. If an external FET is used (internal FET is disabled), then the internal pull-up is not available (an external pull-up is required). xD_CLE 24 O8PD xD-Picture Card Command Strobe An active high Command Latch Enable signal for the xD-Picture Card device. This pin has a weak pull-down resistor that is permanently enabled. GPIO14/ 29 I/O6 General Purpose IO 14 Can be used either as input; edge sensitive interrupt input; or output. Custom firmware is required to activate this function. xD_nCD I/O8 xD-Picture Card Detection GPIO Designated by the default firmware as the xD-Picture Card detection pin and has an internal pull-up. SMSC USB4640/USB4640i 15 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Table 3.2 USB4640/USB4640i Pin Descriptions (continued) SYMBOL 48-PIN QFN BUFFER TYPE xD_nRE 27 O8PU DESCRIPTION xD-Picture Card Read Enable Active low read strobe signal for the xD-Picture Card device. When using the internal FET, this pin has a weak internal pull-up resistor that is tied to the output of the internal power FET. If an external FET is used (internal FET is disabled), then the internal pull-up is not available (an external pull-up is required). xD_nWE 22 O8PU xD-Picture Card Write Enable Active low write strobe signal for the xD-Picture Card device. When using the internal FET, this pin has a weak internal pull-up resistor that is tied to the output of the internal power FET. If an external FET is used (internal FET is disabled), then the internal pull-up is not available (an external pull-up is required). xD_nWP 21 O8PD xD-Picture Card Write Protect Active low write-protect signal for the xD-Picture Card device. This pin has a weak pull-down resistor that is permanently enabled. SPI INTERFACE SPI_CE_n 8 O12 SPI Chip Enable Active low chip enable output. If the SPI interface is enabled, this pin must be driven high in power down states. SPI_CLK/ 9 I/O12 SPI Clock Out Clock signal out to the serial ROM. See Section 3.6: ROM BOOT Sequence on page 21 for diagram and usage instructions. During reset, this pin must be driven low. GPIO4/ I/O6 General Purpose IO 4 Can be used either as input; edge sensitive interrupt input; or output. Custom firmware is required to activate this function. SCL Serial Clock The I2C EEPROM clock pin when the device is connected to the optional I2C EEPROM. Revision 1.3 (05-17-11) 16 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Table 3.2 USB4640/USB4640i Pin Descriptions (continued) SYMBOL 48-PIN QFN BUFFER TYPE SPI_DO/ 10 I/O12 DESCRIPTION SPI Serial Data Out The output for the SPI port. See Section 3.6: ROM BOOT Sequence for diagram and usage instructions. GPIO5/ I/O6 SDA/ This pin may be used either as an input; edge sensitive interrupt input; or output. Custom firmware is required to activate this function. Serial Data Line The I2C EEPROM data pin when the device is connected to the optional I2C EEPROM. SPI_SPD_SEL I/O12 SPI Speed Select Selects the speed of the SPI interface. During nRESET assertion, this pin will be tri-stated with the weak pull-down resistor enabled. When nRESET is negated, the value on the pin will be internally latched, and the pin will revert to SPI_DO functionality, where the internal pull-down will be disabled. 0 : 30 MHz (no external resistor should be applied) 1 : 60 MHz (a 10 k external pull-up resistor must be applied) If the latched value is 1, then the pin is tri-stated when the chip is in the suspend state. If the latched value is 0, then the pin is driven low during a suspend state. SPI_DI 11 I/O12PD SPI Serial Data In The SPI data in to the controller from the ROM. This pin has a weak internal pull-down applied at all times to prevent floating. MISC GPIO1/ 37 I/O6 General Purpose I/O 1 Can be used either as an input; edge sensitive interrupt input; or output. Custom firmware is required to activate this function. LED/ Can be used as an LED output. TXD This signal can be configured as the TXD output of the internal UART. Custom firmware is required to activate this function. GPIO2/ 36 I/O6 General Purpose I/O 2 Can be used either as an input; edge sensitive interrupt input; or output. Custom firmware is required to activate this function. RXD GPIO10 (CRD_PWR) This signal can be configured as input to the RXD of the internal UART. Custom firmware is required to activate this function. 35 I/O200 Card Power Drive: 3.3 V (100 mA or 200 mA) This must be the only FET used to power devices. Failure to do this will violate voltage specifications on device pins. If this pin is not being used as a card power pin, this pin may be used either as an input; edge sensitive interrupt input; or output (GPIO). Please see Section 4.4.2.3: A4h-A5h: Smart Media Device Power Configuration on page 34 for more information. SMSC USB4640/USB4640i 17 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Table 3.2 USB4640/USB4640i Pin Descriptions (continued) SYMBOL 48-PIN QFN BUFFER TYPE nRESET 38 IS DESCRIPTION Reset Input The system uses this active low signal to reset the chip. The active low pulse should be at least 1 s wide. TEST 40 I Test Input Tie to ground for normal operation. DIGITAL / POWER / GROUND CRFILT 15 VDD Core Regulator Filter Capacitor Requires a 1.0 F (or greater) 20% (ESR <0.1) capacitor to VSS. PLLFILT 46 Phase-Locked Loop Regulator Filter Capacitor Requires a 1.0 F (or greater) 20% (ESR < 0.1 ) capacitor to VSS. VDD12 41 1.2 V Power For HSIC pads and buffers VDD33 3.3 V Power and Regulator Input 5 12 16 25 34 48 VSS See Chapter 6: DC Parameters on page 51 for more information. Pins 16 and 48 each require an external bypass capacitor of 4.7 F minimum. ePad Ground Pad/ePad The package slug is the only VSS for the device and must be tied to ground with multiple vias. 3.4 Buffer Type Descriptions Table 3.3 USB4640/USB4640i Buffer Type Descriptions BUFFER I DESCRIPTION Input. I/O Input/output IPU Input with weak internal pull-up IS I/O6 I/OD6PU O8 Input with Schmitt trigger Input/output buffer with 6 mA sink and 6 mA source Input/open drain output buffer with a 6 mA sink Output buffer with an 8 mA sink and an 8 mA source O8PD Output buffer with an 8 mA sink and an 8 mA source with a weak internal pull-down resistor O8PU Output buffer with an 8 mA sink and an 8 mA source with a weak internal pull-up resistor I/O8 Input/output buffer with an 8 mA sink and an 8 mA source Revision 1.3 (05-17-11) 18 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Table 3.3 USB4640/USB4640i Buffer Type Descriptions (continued) BUFFER DESCRIPTION I/O8PD Input/output buffer with an 8 mA sink and an 8 mA source with a weak internal pull-down resistor I/O8PU Input/output buffer with an 8 mA sink and an 8 mA source with a weak internal pull-up resistor O12 Output buffer with a 12 mA sink and a 12 mA source I/O12 Input/output buffer with 12 mA sink and 12 mA source I/O12PD Input/output buffer with 12 mA sink and 12 mA source with a weak internal pull-down resistor I/O200 Input/output buffer 12 mA with FET disabled, 100/200 mA source only when the FET is enabled ICLKx XTAL clock input OCLKx XTAL clock output I/O-U I-R Analog input/output as defined in the USB 2.0 Specification RBIAS SMSC USB4640/USB4640i 19 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 3.5 Port Power Control 3.5.1 Port Power Control Using a USB Power Switch The USB4640/USB4640i has a single port power control and over-current sense signal for each downstream port. When disabling port power, the driver will actively drive a 0. To avoid unnecessary power dissipation, the internal pull-up resistor will be disabled at that time. When port power is enabled, the output driver is disabled, and the pull-up resistor is enabled creating an open drain output. If there is an over-current situation, the USB Power Switch will assert the open drain OCS signal. The Schmitt trigger input will detect this event as a low. The open drain output does not interfere. The internal over-current sense filter handles the transient conditions, such as low voltage, while the device is powering up. 5V PRTCTL3 OCS USB Power Switch EN USB Device USB4640/40i 5V PRTCTL2 OCS USB Power Switch EN USB Device Figure 3.2 Port Power Control with USB Power Switch 3.5.2 Port Power Control Using a Poly Fuse When using the USB4640/USB4640i with a poly fuse, an external diode must be used (see Figure 3.3). When disabling port power, the USB4640/USB4640i will drive a 0. This procedure will have no effect since the external diode will isolate the pin from the load. When port power is enabled, the USB4640/USB4640i output driver is disabled, and the pull-up resistor is enabled which creates an open drain output. This open drain output condition means that the pull-up resistor is providing 3.3 volts to the anode of the diode. If there is an over-current situation, the poly fuse will open. This will cause the cathode of the diode to go to zero volts. The anode of the diode will be at 0.7 volts, and the Revision 1.3 (05-17-11) 20 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Schmitt trigger input will register this as a low resulting in an over-current detection. The open drain output does not interfere. 5V PRTCTL3 USB Device USB4640/40i 5V PRTCTL2 USB Device Figure 3.3 Port Power Control with a Single Poly Fuse and Multiple Loads When using a single poly fuse to power all devices, note that for the ganged situation, all power control pins must be tied together. 5V PRTCTL3 Poly Fuse USB4640/40i PRTCTL2 USB Device USB Device Figure 3.4 Port Power with Ganged Control with Poly Fuse 3.6 ROM BOOT Sequence After power-on reset, the internal firmware checks for an external SPI flash device that contains a valid signature of 2DFU (device firmware upgrade) beginning at address 0xFFFA. If a valid signature is found, then the external ROM is enabled and code execution begins at address 0x0000 in the external SPI device. Otherwise, code execution continues from the internal ROM. If there is no SPI ROM detected, the internal firmware then checks for the presence of an I2C ROM. The firmware looks for the signature ATA2 at the offset of FCh-FFh and ecf1 at the offset of 17Ch17Fh in the I2C ROM. The firmware reads in the I2C ROM to configure the hardware and software internally. Please refer to Section 4.3.2: EEPROM Data Descriptor on page 26 for the details of the configuration options. The SPI ROM required for the USB4640/USB4640i is a recommended minimum of 1 Mb and support either 30 MHz or 60 MHz. The frequency used is set using the SPI_SPD_SEL. For 30 MHz operation, this pin must be pulled to ground through a 100 k resistor. For 60 MHz operation, this pin must pulled up through a 100 k resistor. SMSC USB4640/USB4640i 21 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet The SPI_SPD_SEL pin is used to choose the speed of the SPI interface. During nRESET assertion, this pin will be tri-stated with the weak pull-down resistor enabled. When nRESET is negated, the value on the pin will be internally latched, and the pin will revert to SPI_DO functionality. The internal pulldown will be disabled. The firmware can determine the speed of operation on the SPI port by checking the SPI_CTL.SPI_SPEED bit (0x2400 - RESET = 0x02). Both 1- and 2-bit SPI operation is supported. For optimum throughput, a 2-bit SPI ROM is recommended. Both mode 0 and mode 3 SPI ROMS are also supported. SPI_CE_N SPI_CLK/GPIO4/SCL USB4640/40i CE# CLK SPI_DO/GPIO5/SDA/SPI_SPD_SEL SPI_DI SPI ROM SI SO Figure 3.5 SPI ROM Connection 3. 3 V 10 K SCL 3. 3 V I2C ROM USB4640/40i 10 K SDA Figure 3.6 I2C Connection 3.7 Pin Reset States Hardware Initialization Voltage Signal (v) Firmware Operational RESET RESET VDD33 Time (t) VSS Figure 3.7 Pin Reset States Revision 1.3 (05-17-11) 22 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Table 3.4 Legend for Pin Reset States Table SYMBOL DESCRIPTION 0 Output driven low 1 Output driven high IP Input enabled PU Hardware enables pull-up PD Hardware enables pull-down none Hardware disables pad -- Hardware disables function Z Hardware disables pad. Both output driver and input buffers are disabled. Table 3.5 USB4640/USB4640i Reset States Table RESET STATE PIN PIN NAME FUNCTION INPUT/ OUTPUT PU/ PD 1 USBDN_DM2 USBDN_DM2 IP PD 2 USBDN_DP2 USBDN_DP2 IP PD 3 USBDN_DM3 USBDN_DM3 IP PD 4 USBDN_DP3 USBDN_DP3 IP PD 6 PRTCTL2 PRTCTL 0 -- 7 PRTCTL3 PRTCTL 0 -- 8 SPI_CE_n SPI_CE_n 1 -- 9 SPI_CLK/GPIO4/SCL GPIO 0 -- 10 SPI_DO/GPIO5/SDA/SPI_SPD_SEL GPIO 0 -- 11 SPI_DI SPI_DI IP PD 13 GPIO6/SD_WP/MS_SCLK/xD_D4 GPIO 0 -- 14 GPIO15/SD_nCD GPIO IP PU 17 SD_D1/MS_D5/xD_D3 none Z -- 18 SD_D0/MS_D4/xD_D2 none Z -- 19 SD_D7/MS_D6/xD_D1 none Z -- SMSC USB4640/USB4640i 23 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Table 3.5 USB4640/USB4640i Reset States Table (continued) RESET STATE PIN PIN NAME FUNCTION INPUT/ OUTPUT PU/ PD 20 SD_D6/MS_D7/xD_D0 none Z -- 21 SD_CLK/MS_BS/xD_nWP none Z -- 22 xD_nWE xD_nWE Z -- 23 SD_D5/MS_D1/xD_ALE none Z -- 24 SD_CMD/MS_D0/xD_CLE none Z -- 26 xD_nCE xD_nCE Z -- 27 xD_nRE xD_nRE Z -- 28 xD_nB/R xD_nB/R Z -- 29 GPIO14/xD_nCD GPIO IP PU 30 SD_D4/MS_D2/xD_D7 none Z -- 31 GPIO12/MS_INS GPIO IP PU 32 SD_D3/MS_D3/xD_D6 none Z -- 33 SD_D2/xD_D5 none Z -- 35 GPIO10 (CRD_PWR) GPIO Z -- 36 GPIO2/RXD GPIO 0 -- 37 GPIO1/LED/TXD GPIO 0 -- 38 nRESET nRESET IP -- 39 HSIC_IMP HSIC_IMP Z -- 40 TEST TEST IP PD 42 HSIC_DAT HSIC_DAT IP -- 43 HSIC_STROBE HSIC_STROBE IP -- Revision 1.3 (05-17-11) 24 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Chapter 4 Configuration Options 4.1 Hub SMSC's USB 2.0 hub is fully compliant to the Universal Serial Bus Specification [1]. The hub provides 1 transaction translator (TT) that is shared by both downstream ports defined as a single-TT configuration. The TT contains 4 non-periodic buffers. The hub supports a large number of features (some are mutually exclusive), and must be configured in order to correctly function when attached to a USB host controller. There are two principal ways to configure the hub: Internal default settings External EEPROM or SPI Flash device Note: See Chapter 11 (Hub Specification) of the USB specification for general details regarding hub operation and functionality. 4.2 Card Reader The SMSC USB4640/USB4640i is fully compliant with the following flash media card reader specifications: Secure Digital 2.0/MultiMediaCard 4.2 --SD 2.0, HS-SD, HC-SD --TransFlashTM and reduced form factor media --1/4/8 bit MMC 4.2 Memory Stick 1.43 Memory Stick Pro Format 1.02 Memory Stick Pro-HG Duo Format 1.01 --Memory Stick, MS Duo, HS-MS, MS Pro-HG, MS Pro Memory Stick Duo 1.10 xD-Picture Card 1.2 4.3 System Configurations 4.3.1 EEPROM/SPI Interface The USB4640/USB4640i can be configured via a 2-wire I2C EEPROM (512x8) or an external SPI flash device containing the USB4640/USB4640i firmware. If an external configuration device does not exist the internal default values will be used. If one of the external devices is used for configuration, the USB4640/USB4640i values can be updated through the USB interface. The hub will then attach to the upstream USB host. The USBDM tool set is available in the USB264x Hub Card reader combo software release package. To download the software package from SMSC's website, visit: https://www2.smsc.com/mkt/CW_SFT_PUB.nsf/Agreements/OBJ+Hub+Card+Reader Review the license and select the I agree checkbox, followed by the Confirm button. Download the USB264x Hub Card reader combo Release Package zip file with the USBDM tool set will then be available for download. SMSC USB4640/USB4640i 25 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.3.2 EEPROM Data Descriptor Table 4.1 Internal Flash Media Controller Configurations ADDRESS REGISTER NAME 00h USB_SER_LEN USB Serial String Descriptor Length 1Ah 01h USB_SER_TYP USB Serial String Descriptor Type 03h 02h-19h USB_SER_NUM USB Serial Number 1Ah-1Bh USB_VID USB Vendor Identifier 0424 1Ch-1Dh USB_PID USB Product Identifier 4040 1Eh USB_LANG_LEN USB Language String Descriptor Length 04h 1Fh USB_LANG_TYP USB Language String Descriptor Type 03h 20h USB_LANG_ID_LSB USB Language Identifier Least Significant Byte 09h (Note 4.3) 21h USB_LANG_ID_MSB USB Language Identifier Most Significant Byte 04h (Note 4.3) 22h USB_MFR_STR_LEN USB Manufacturer String Descriptor Length 10h 23h USB_MFR_STR_TYP USB Manufacturer String Descriptor Type 03h 24h-31h USB_MFR_STR USB Manufacturer String Generic (Note 4.1) 32h-5Dh rsvd 5Eh USB_PRD_STR_LEN USB Product String Descriptor Length 30h 5Fh USB_PRD_STR_TYP USB Product String Descriptor Type 03h 60h-99h USB_PRD_STR USB Product String Ultra Fast Media Reader (Note 4.1) 9Ah USB_BM_ATT USB BmAttribute 80h 9Bh USB_MAX_PWR USB Max Power 30h (96 mA) 9Ch ATT_LB Attribute Lo byte 40h (reverse SD_WP only) 9Dh ATT_HLB Attribute Hi Lo byte 80h (reverse SD2_WP only) 9Eh ATT_LHB Attribute Lo Hi byte 00h 9Fh ATT_HB Attribute Hi byte 00h A0h MS_PWR_LB Memory Stick Device Power Lo byte 00h A1h MS_PWR_HB Memory Stick Device Power Hi byte 0Ah Revision 1.3 (05-17-11) DESCRIPTION INTERNAL DEFAULT VALUE 000008264001 (Note 4.1) 00h 26 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Table 4.1 Internal Flash Media Controller Configurations (continued) ADDRESS REGISTER NAME DESCRIPTION INTERNAL DEFAULT VALUE A2h-A3h N/A A4h SM_PWR_LB Smart Media Device Power Lo byte 00h (Note 4.2) A5h SM_PWR_HB Smart Media Device Power Hi byte 0Ah (Note 4.2) A6h SD_PWR_LB Secure Digital Device Power Lo byte 00h A7h SD_PWR_HB Secure Digital Device Power Hi byte 0Ah A8h LED_BLK_INT LED Blink Interval 02h A9h LED_BLK_DUR LED Blink After Access 28h AAh - B0h DEV0_ID_STR Device 0 Identifier String N/A B1h - B7h DEV1_ID_STR Device 1 Identifier String MS B8h - BEh DEV2_ID_STR Device 2 Identifier String SM (Note 4.2) BFh - C5h DEV3_ID_STR Device 3 Identifier String SD/MMC C6h - CDh INQ_VEN_STR Inquiry Vendor String Generic CEh - D2h INQ_PRD_STR Inquiry Product String 82640 D3h DYN_NUM_LUN Dynamic Number of LUNs D4h - D7h DEV_LUN_MAP Device to LUN Mapping D8h - DAh rsvd 00h, 06h, 0Dh DBh - DDh rsvd 59h, 56h, 97h 00h 01h FFh, 00h, 00h, 00h Note 4.1 This value is a UNICODE UTF-16LE encoded string value that meets the USB 2.0 Specification [1]. Note 4.2 A value of SM will be overridden with xD once an xD-Picture Card has been identified. Note 4.3 Current 16-bit language ID's are defined by the USB-IF, see The Unicode Standard, Worldwide Character Encoding [4]. Table 4.2 Hub Controller Configurations ADDRESS REGISTER NAME DEh VID_LSB Vendor ID Least Significant Byte 24h DFh VID_MSB Vendor ID Most Significant Byte 04h E0h PID_LSB Product ID Least Significant Byte 40h E1h PID_MSB Product ID Most Significant Byte 26h E2h DID_LSB Device ID Least Significant Byte A1h E3h DID_MSB Device ID Most Significant Byte 08h SMSC USB4640/USB4640i DESCRIPTION 27 DATASHEET INTERNAL DEFAULT VALUE Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Table 4.2 Hub Controller Configurations ADDRESS REGISTER NAME DESCRIPTION INTERNAL DEFAULT VALUE E4h CFG_DAT_BYT1 Configuration Data Byte 1 8Bh E5h CFG_DAT_BYT2 Configuration Data Byte 2 28h E6h CFG_DAT_BYT3 Configuration Data Byte 3 00h E7h NR_DEVICE Non-Removable Devices 02h E8h PORT_DIS_SP Port Disable (Self) 00h E9h PORT_DIS_BP Port Disable (Bus) 00h EAh MAX_PWR_SP Max Power (Self) 01h EBh MAX_PWR_BP Max Power (Bus) 32h ECh HC_MAX_C_SP Hub Controller Max Current (Self) 01h EDh HC_MAX_C_BP Hub Controller Max Current (Bus) 32h EEh PWR_ON_TIME Power-on Time 32h EFh BOOST_UP Boost_Up 00h F0h BOOST_3:0 Boost_3:0 00h F1h PRT_SWP Port Swap 00h F2h PRTM12 Port Map 12 00h F3h PRTM3 Port Map 3 00h Table 4.3 Other Internal Configurations ADDRESS REGISTER NAME F4h rsvd 00h F5h rsvd 66h F6h rsvd 00h F7-FAh N/A N/A FBh N/A 00h FCh-FFh NVSTORE_SIG 4.4 DESCRIPTION INTERNAL DEFAULT VALUE Non-Volatile Storage Signature ATA2 Internal Flash Media Controller Extended Configurations Set bit 7 of bmAttribute to enable these extended configuration registers. Table 4.4 Internal Flash Media Controller Extended Configurations ADDRESS REGISTER NAME 100h - 106h CLUN0_ID_STR 107h- 129h N/A Revision 1.3 (05-17-11) DESCRIPTION Combo LUN 0 Identifier String INTERNAL DEFAULT VALUE COMBO N/A 28 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Table 4.4 Internal Flash Media Controller Extended Configurations (continued) ADDRESS REGISTER NAME DESCRIPTION INTERNAL DEFAULT VALUE 12Ah-145h N/A 00h 146h N/A 01h 147h - 14Bh N/A 01h, FFh, FFh, FFh, FFh 14Ch N/A 0Ah 14Dh-17Bh N/A 00h 17Ch-17Fh NVSTORE_SIG2 Non-Volatile Storage Signature 4.4.1 EEPROM Data Descriptor Register Descriptions 4.4.1.1 00h: USB Serial String Descriptor Length ecf1 BYTE NAME DESCRIPTION 0 USB_SER_LEN USB serial string descriptor length as defined by Section 9.6.7: String of the USB 2.0 Specification [1]. This field is the bLength, which describes the size of the string descriptor (in bytes). 4.4.1.2 01h: USB Serial String Descriptor Type BYTE NAME DESCRIPTION 1 USB_SER_TYP USB serial string descriptor type as defined by Section 9.6.7: String of the USB 2.0 Specification [1]. This field is the bDescriptorType, a constant value associated with a string descriptor type. 4.4.1.3 02h-19h: USB Serial Number Option BYTE NAME 25:2 USB_SER_NUM 4.4.1.4 Maximum string length is 12 hex digits. Must be unique to each device. 1Ah-1Bh: USB Vendor ID Option BYTE NAME 1:0 USB_VID 4.4.1.5 DESCRIPTION DESCRIPTION This ID is unique for every vendor. The vendor ID is assigned by the USB Implementer's Forum. 1Ch-1Dh: USB Product ID Option BYTE NAME 1:0 USB_PID SMSC USB4640/USB4640i DESCRIPTION The product ID: assigned by the vendor; unique for every product. 29 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.1.6 1Eh: USB Language Identifier Descriptor Length BYTE NAME DESCRIPTION 0 USB_LANG_LEN USB language ID string descriptor length as defined by Section 9.6.7: String of the USB 2.0 Specification [1]. This field is the bLength, which describes the size of the string descriptor (in bytes). 4.4.1.7 1Fh: USB Language Identifier Descriptor Type BYTE NAME DESCRIPTION 1 USB_LANG_TYP USB language ID string descriptor type as defined by Section 9.6.7: String of the USB 2.0 Specification [1]. This field is the bDescriptorType, a constant value associated with a string descriptor type. 4.4.1.8 20h: USB Language Identifier Least Significant Byte BYTE NAME 2 USB_LANG_ID _LSB 4.4.1.9 English language code = 0409. See Note 4.3 for additional language IDs defined by the USB-IF. 21h: USB Language Identifier Most Significant Byte BYTE NAME 3 USB_LANG_ID _MSB 4.4.1.10 DESCRIPTION DESCRIPTION English language code = 0409. See Note 4.3 for additional language IDs defined by the USB-IF. 22h: USB Manufacturer String Descriptor Length BYTE NAME DESCRIPTION 0 USB_MFR_STR _LEN USB manufacturer string descriptor length as defined by Section 9.6.7 String of the USB 2.0 Specification [1]. This field is the bLength which describes the size of the string descriptor (in bytes). 4.4.1.11 23h: USB Manufacturer String Descriptor Type BYTE NAME DESCRIPTION 1 USB_MFR_STR _TYP USB manufacturer string descriptor type as defined by Section 9.6.7 String of the USB 2.0 Specification [1]. This field is the bDescriptorType, a constant value associated with a string descriptor type. 4.4.1.12 24h-31h: USB Manufacturer String Option BYTE NAME 15:2 USB_MFR_STR Revision 1.3 (05-17-11) DESCRIPTION The maximum string length is 28 characters. 30 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.1.13 32h-5Dh: Reserved BYTE NAME 59:16 rsvd 4.4.1.14 DESCRIPTION 5Eh: USB Product String Descriptor Length BYTE NAME DESCRIPTION 0 USB_PRD_STR _LEN USB product string descriptor length as defined by Section 9.6.7 String of the USB 2.0 Specification [1]. This field is the bLength, which describes the size of the string descriptor (in bytes). 4.4.1.15 5Fh: USB Product String Descriptor Type BYTE NAME DESCRIPTION 1 USB_PRD_STR _TYP USB product string descriptor type as defined by Section 9.6.7 String of the USB 2.0 Specification [1]. This field is the bDescriptorType, a constant value associated with a string descriptor type. 4.4.1.16 60h-99h: USB Product String Option BYTE NAME DESCRIPTION 59:2 USB_PRD_STR This string will be used during the USB enumeration process in the Windows(R) operating system. Maximum string length is 28 characters. 4.4.1.17 9Ah: USB BmAttribute (1 Byte) BIT NAME 7:0 USB_BM_ATT DESCRIPTION Self- or Bus-Power: selects between self- and bus-powered operation. The hub is either self-powered (draws less than 2 mA) or bus-powered (limited to 100 mA maximum power prior to being configured by the host controller). When configured as a bus-powered device, the hub consumes less than 100 mA of current prior to being configured. After configuration, the buspowered SMSC hub (along with all associated hub circuitry, any embedded devices if part of a compound device, and 100 mA per externally available downstream port) must consume no more than 500 mA of current. The current consumption is system dependent and must follow the USB 2.0 Specification requirements. When configured as a self-powered device, <1 mA of current is consumed and all ports are available, with each port being capable of sourcing 500 mA of current. 80 C0 A0 E0 SMSC USB4640/USB4640i : : : : (default) Bus-powered operation Self-powered operation Bus-powered operation with remote wake-up Self-powered operation with remote wake-up 31 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.1.18 9Bh: USB MaxPower (1 Byte) BIT NAME DESCRIPTION 7:0 USB_MAX_PWR USB Max Power per the USB 2.0 Specification [1]. Do NOT set this value greater than 100 mA. 4.4.1.19 9Ch-9Fh: Attribute Byte Descriptions BYTE BYTE NAME BIT 0 ATT_LB 3:0 4 DESCRIPTION Always read as 0 Inquire Manufacturer and Product ID Strings 1 : use the Inquiry Manufacturer and Product ID Strings 0 : (default) use the USB Descriptor Manufacturer and Product ID Strings 5 Always read as 0 6 Reverse SD Card Write Protect Sense 1 : (default) SD cards will be write protected when SW_nWP is high, and writable when SW_nWP is low. 0 : SD cards will be write protected when SW_nWP is low, and writable when SW_nWP is high. 7 Extended Configuration Enable 1 : enables editing, updating, and reading from registers 100h-17Fh. 0 : internal configuration is loaded, where it will not read from registers 100h-17Fh. 1 ATT_HLB 3:0 4 Always read as 0 Activity LED True Polarity 1 : activity LED to low true 0 : (default) - activity LED polarity to high true 5 Common Media Insert/Media Activity LED 1 : activity LED will function as a common media inserted/media access LED. 0 : (default) - activity LED will remain in its idle state until media is accessed. 6 Always read as 0 7 Reverse SD2 Card Write Protect Sense 1 : (default) - SD cards in LUN 1 will be write protected when SW_nWP is high, and writable when SW_nWP is low. 0 : SD cards in LUN 1 will be write protected when SW_nWP is low, and writable when SW_nWP is high. Revision 1.3 (05-17-11) 32 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet BYTE BYTE NAME BIT 2 ATT_LHB 0 DESCRIPTION Attach on Card Insert/Detach on Card Removal 1 : attach on insert is enabled 0 : (default) - attach on insert is disabled 1 Always read as 0 2 Enable Device Power Configuration 1 : Custom Device Power Configuration stored in the NVSTORE is used 0 : (default) - Default Device Power Configuration is used 3 4.4.2 ATT_HB 7:3 Always read as 0 6:0 Always read as 0 7 xD Player Mode A0h-A7h: Device Power Configuration The USB4640/USB4640i has one internal FET which can be utilized for card power. This section describes the default internal configuration. The settings are stored in NVSTORE and provide the following features: 1. A card can be powered by an external FET or by an internal FET. 2. The power limit can be set to 100 mA or 200 mA (default) for the internal FET. Each media uses two bytes to store its device power configuration. Bit 3 selects between internal or external card power FET options. For internal FET card power control, bits 0 through 2 are used to set the power limit. The Device Power Configuration bits are ignored unless the Enable Device Power Configuration bit is set. See Section 4.4.1.19 on page 32. 4.4.2.1 A0h-A1h: Memory Stick Device Power Configuration FET NAME BITS BIT TYPE 0 MS_PWR_LB 3:0 Low Nibble FET Lo Byte 7:4 High Nibble 0000 : disabled 3:0 Low Nibble FET Hi Byte 1 2 MS_PWR_HB DESCRIPTION 0000 0001 1000 1010 3 4.4.2.2 7:4 High Nibble : : : : disabled external FET enabled internal FET - 100 mA power limit (default) internal FET - 200 mA power limit 0000 : disabled A2h-A3h: Not Applicable BYTE NAME 1:0 N/A SMSC USB4640/USB4640i DESCRIPTION 33 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.2.3 FET A4h-A5h: Smart Media Device Power Configuration NAME BITS 0 BIT TYPE 3:0 Low Nibble FET Lo Byte: 7:4 High Nibble 0000 : disabled 3:0 Low Nibble FET Hi Byte SM_PWR_LB 1 2 SM_PWR_HB DESCRIPTION 0000 0001 1000 1010 3 7:4 4.4.2.4 High Nibble : : : : disabled external FET enabled internal FET - 100 mA power limit (default) internal FET - 200 mA power limit 0000 : disabled A6h-A7h: Secure Digital Device Power Configuration FET NAME BITS 0 SD_PWR_LB 3:0 Low Nibble FET Lo Byte: 7:4 High Nibble 0000 : disabled 3:0 Low Nibble FET Hi Byte 1 2 SD_PWR_HB BIT TYPE DESCRIPTION 0000 0001 1000 1010 3 7:4 4.4.2.5 High Nibble : : : : disabled external FET enabled internal FET - 100 mA power limit (default) internal FET - 200 mA power limit 0000b : disabled A8h: LED Blink Interval BYTE NAME DESCRIPTION 0 LED_BLK_INT The blink rate is programmable in 50 ms intervals. The high bit (7) indicates an idle state: 0 : off 1 : on The remaining bits (6:0) are used to determine the blink interval up to a max of 128 x 50 ms. 4.4.2.6 A9h: LED Blink Duration BYTE NAME DESCRIPTION 1 LED_BLK_DUR LED Blink After Access: designates the number of seconds that the GPIO1 LED will continue to blink after a drive access. Setting this byte to 05 will cause the GPIO 1 LED to blink for 5 seconds after a drive access. Revision 1.3 (05-17-11) 34 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.3 Device ID Strings These bytes are used to specify the LUN descriptor returned by the device. These bytes are used in combination with the device to LUN mapping bytes in applications where the LUNs need to be reordered and renamed. If multiple devices are mapped to the same LUN (a COMBO LUN), then the CLUN#_ID_STR will be used to name the COMBO LUN instead of the individual device strings. When applicable, the SM value will be overridden with xD once an xD-Picture Card has been identified. 4.4.3.1 AAh-B0h: Device 0 Identifier String BYTE NAME 6:0 DEV0_ID_STR 4.4.3.2 NAME 6:0 DEV1_ID_STR NAME 6:0 DEV2_ID_STR NAME 6:0 DEV3_ID_STR DESCRIPTION ID string is associated with the Smart Media (Note 4.2) device DESCRIPTION ID string is associated with the Secure Digital/MultiMediaCard device C6h-CDh: Inquiry Vendor String BYTE NAME 7:0 INQ_VEN_STR 4.4.3.6 ID string is associated with the Memory Stick device BFh-C5h: Device 3 Identifier String BYTE 4.4.3.5 DESCRIPTION B8h-BEh: Device 2 Identifier String BYTE 4.4.3.4 N/A B1h-B7h: Device 1 Identifier String BYTE 4.4.3.3 DESCRIPTION DESCRIPTION If bit 4 of the first attribute byte is set, the device will use these strings in response to a USB inquiry command, instead of the USB descriptor manufacturer and product ID strings. CEh-D2h: Inquiry Product String BYTE NAME 4:0 INQ_PRD_STR SMSC USB4640/USB4640i DESCRIPTION If bit 4 of the first attribute byte is set, the device will use these strings in response to a USB inquiry command, instead of the USB descriptor manufacturer and product ID strings. 35 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.3.7 D3h: Dynamic Number of LUNs BIT NAME DESCRIPTION 7:0 DYN_NUM_LUN These bytes are used to specify the number of LUNs the device exposes to the host. These bytes are also used for icon sharing by assigning more than one LUN to a single icon. This is used in applications where the device utilizes a combo socket with only a single icon displayed for one or more interfaces. If this field is set to FF, the program assumes that you are using the default value and icons will be configured per the default configuration. 4.4.3.8 D4h-D7h: Device to LUN Mapping BYTE NAME DESCRIPTION 3:0 DEV_LUN_MAP These registers map a device controller (SD/MMC, SM (Note 4.2), and MS) to a Logical Unit Number (LUN). The device reports the mapped LUNs to the USB host in the USB descriptor during enumeration. The icon installer associates custom icons with the LUNs specified in these fields. Setting a register to FF indicates that the device is not mapped. Setting all of the DEV_LUN_MAP registers for all devices to FF forces the use of the default mapping configuration. Not all configurations are valid. Valid configurations depend on the hardware, packaging, and the board layout. The number of unique LUNs mapped must match the value in the Section 4.4.3.7 on page 36. 4.4.3.9 D8h-DDh: Reserved BYTE NAME 2:0 rsvd DESCRIPTION 4.4.4 Hub Controller Configurations 4.4.4.1 DEh: Vendor ID (LSB) BIT BYTE NAME DESCRIPTION 7:0 VID_LSB Least Significant Byte of the Vendor ID: a unique 16-bit value that identifies the vendor of the user device (assigned by USB Implementer's Forum). 4.4.4.2 DFh: Vendor ID (MSB) BIT BYTE NAME 7:0 VID_MSB Revision 1.3 (05-17-11) DESCRIPTION Most Significant Byte of the Vendor ID: a unique 16-bit value that identifies the vendor of the user device (assigned by USB Implementer's Forum). 36 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.4.3 E0h: Product ID (LSB) BIT NAME DESCRIPTION 7:0 PID_LSB Least Significant Byte of the Product ID: a unique 16-bit value that identifies a particular product (vender assigned). 4.4.4.4 E1h: Product ID (MSB) BIT NAME DESCRIPTION 7:0 PID_MSB Most Significant Byte of the Product ID. a unique 16-bit value that identifies a particular product (vender assigned). 4.4.4.5 E2h: Device ID (LSB) BIT NAME 7:0 DID_LSB 4.4.4.6 Least Significant Byte of the Device ID: a 16-bit device release number in BCD (binary coded decimal) format. E3h: Device ID (MSB) BIT NAME 7:0 DID_MSB 4.4.4.7 DESCRIPTION DESCRIPTION Most Significant Byte of the Device ID: a 16-bit device release number in BCD format. E4h: Configuration Data Byte 1 (CFG_DAT_BYT1) BIT NAME 7 SELF_BUS_PWR DESCRIPTION Self- or Bus-Power: Selects between self- and bus-powered operation. The hub is either self-powered (draws less than 2 mA) or bus-powered (limited to 100 mA maximum power prior to being configured by the host controller). When configured as a bus-powered device, the SMSC hub consumes less than 100 mA of current prior to being configured. After configuration, the buspowered hub (along with all associated hub circuitry, any embedded devices if part of a compound device, and 100 mA per externally available downstream port) must consume no more than 500 mA of current. The current consumption is system dependent, and the USB 2.0 specifications must not be violated. When configured as a self-powered device, <1 m A of current is consumed and all ports are available, with each port being capable of sourcing 500 mA of current. 0 : Bus-powered operation 1 : Self-powered operation 6:3 rsvd SMSC USB4640/USB4640i 37 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet BIT NAME 2:1 CURRENT_SNS DESCRIPTION Over-Current Sense Selects current sensing on a port-by-port basis, all ports ganged, or none (only for bus-powered hubs). The ability to support current sensing on a per port or ganged basis is dependent upon the hardware implementation. 00 : Ganged sensing (all ports together) 01 : individual (port-by-port) 1x : over-current sensing not supported (must only be used with buspowered configurations) 0 PORT_PWR Port Power Switching Enables power switching on all ports simultaneously (ganged), or port power is individually switched on and off on a port-by-port basis (individual). The ability to support power enabling on a port or ganged basis is dependent upon the hardware implementation. 0 : ganged switching (all ports together) 1 : individual port-by-port switching 4.4.4.8 E5h: Configuration Data Byte 2 (CFG_DAT_BYT2) BIT NAME 7:6 rsvd 5:4 OC_TIMER DESCRIPTION OverCurrent Timer: over-current timer delay 00 01 10 11 3 COMPOUND : : : : 50 ns 100 ns 200 ns 400 ns Compound Device: allows OEM to indicate that the hub is part of a compound device (per the USB 2.0 Specification). The applicable port(s) must also be defined as having a "non-removable device". When configured via strapping options, declaring a port as non-removable automatically causes the hub controller to report that it is part of a compound device. 0 : no 1 : yes, the hub is part of a compound device 2:0 Revision 1.3 (05-17-11) rsvd 38 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.4.9 E6h: Configuration Data Byte 3 (CFG_DAT_BYT3) BIT NAME 7:4 rsvd 3 PRTMAP_EN DESCRIPTION Port Mapping Enable: selects the method used by the hub to assign port numbers and disable ports. 0 : Standard Mode. Strap options or the following registers are used to define which ports are enabled, and the ports are mapped as port `n' on the hub is reported as port `n' to the host, unless one of the ports is disabled, then the higher numbered ports are remapped in order to report contiguous port numbers to the host. Register 300Ah: Port disable for self-powered operation (Reset = 0x00) Register 300Bh: Port disable for bus-powered operation (Reset = 0x00) 1 : Port Map mode. The mode enables remapping via the registers defined below. Register 30FBh: Port Map 12 (Reset = 0x00) Register 30FCh: Port Map 3 (Reset = 0x00) 2:0 4.4.4.10 rsvd E7h: Non-Removable Device BIT BYTE NAME 7:0 NR_DEVICE DESCRIPTION Indicates which port(s) include non-removable devices. 0 : Port is removable 1 : Port is non-removable Informs the host if one of the active ports has a permanent device that is undetachable from the hub. The device must provide its own descriptor data. When using the internal default option, NON_REM[1:0] designates the appropriate ports as being non-removable. Bit Bit Bit Bit Bit Bit Bit Bit 7 6 5 4 3 2 1 0 : : : : : : : : Note: SMSC USB4640/USB4640i rsvd rsvd rsvd rsvd controls physical port 3 controls physical port 2 controls physical port 1 rsvd Bit 1 must be set to a 1 by the firmware for proper identification of the card reader as a non-removable device. 39 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.4.11 E8h: Port Disable For Self-Powered Operation BIT BYTE NAME 7:0 PORT_DIS_SP DESCRIPTION Disables 1 or more ports. 0 : port is available 1 : port is disabled During self-powered operation this register selects the ports which will be permanently disabled. The ports are unavailable to be enabled or enumerated by a host controller. The ports can be disabled in any order since the internal logic will automatically report the correct number of enabled ports to the USB host and will reorder the active ports in order to ensure proper function. Bit Bit Bit Bit Bit Bit Bit Bit 4.4.4.12 7 6 5 4 3 2 1 0 : : : : : : : : rsvd rsvd rsvd rsvd controls physical port 3 controls physical port 2 controls physical port 1 rsvd E9h: Port Disable For Bus-Powered Operation BIT BYTE NAME 7:0 PORT_DIS_BP DESCRIPTION Disables 1 or more ports. 0 : port is available 1 : port is disabled During self-powered operation, this register selects the ports which will be permanently disabled. The ports are unavailable to be enabled or enumerated by a host controller. The ports can be disabled in any order, the internal logic will automatically report the correct number of enabled ports to the USB host and will reorder the active ports in order to ensure proper function. When using the internal default option, PRT_DIS[1:0] disable the appropriate ports. Bit Bit Bit Bit Bit Bit Bit Bit 4.4.4.13 7 6 5 4 3 2 1 0 : : : : : : : : rsvd rsvd rsvd rsvd controls physical port 3 controls physical port 2 controls physical port 1 rsvd EAh: Max Power For Self-Powered Operation BIT BYTE NAME DESCRIPTION 7:0 MAX_PWR_SP Value in 2 mA increments that the hub consumes when operating as a selfpowered hub. This value includes the hub silicon along with the combined power consumption of all associated circuitry on the board. This value also includes the power consumption of a permanently attached peripheral if the hub is configured as a compound device, and the embedded peripheral reports 0 mA in its descriptors. Note: Revision 1.3 (05-17-11) Per USB 2.0 Specification: this value cannot exceed 100 mA. 40 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.4.14 EBh: Max Power For Bus-Powered Operation BIT BYTE NAME DESCRIPTION 7:0 MAX_PWR_BP Value in 2 mA increments that the hub consumes when operating as a buspowered hub. This value includes the hub silicon along with the combined power consumption of all associated circuitry on the board. This value also includes the power consumption of a permanently attached peripheral if the hub is configured as a compound device, and the embedded peripheral reports 0 mA in its descriptors. 4.4.4.15 ECh: Hub Controller Max Current For Self-Powered Operation BIT BYTE NAME DESCRIPTION 7:0 HC_MAX_C_SP Value in 2 mA increments that the hub consumes when operating as a selfpowered hub. This value includes the hub silicon along with the combined power consumption of all associated circuitry on the board. This value does NOT include the power consumption of a permanently attached peripheral if the hub is configured as a compound device. Note: Per USB 2.0 Specification: this value cannot exceed 100 mA. A value of 50 (decimal) indicates 100 mA, which is the default value. 4.4.4.16 EDh: Hub Controller Max Current For Bus-Powered Operation BIT BYTE NAME DESCRIPTION 7:0 HC_MAX_C_BP Value in 2 mA increments that the hub consumes when operating as a buspowered hub. This value will include the hub silicon along with the combined power consumption of all associated circuitry on the board. This value will NOT include the power consumption of a permanently attached peripheral if the hub is configured as a compound device. A value of 50 (decimal) would indicate 100 mA, which is the default value. 4.4.4.17 EEh: Power-On Time BIT BYTE NAME DESCRIPTION 7:0 PWR_ON_TIME The length of time that it takes (in 2 ms intervals) from the time the host initiated power-on sequence begins on a port until power is adequate on that port. If the host requests the power-on time, the system software uses this value to determine how long to wait before accessing a powered-on port. SMSC USB4640/USB4640i 41 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.4.18 EFh: Boost_Up BIT NAME 7:2 rsvd 1:0 BOOST_IOUT DESCRIPTION USB electrical signaling drive strength boost bit for the upstream port A. 00 01 10 11 : : : : Normal electrical drive strength Elevated electrical drive strength Elevated electrical drive strength Elevated electrical drive strength Note: 4.4.4.19 Boost could result in non-USB compliant parameters. Therefore, a value of 00 should be implemented unless specific implementation issues require additional signal boosting to correct for degraded USB signalling levels. F0h: Boost_3:0 BIT NAME 7:6 rsvd 5:4 BOOST_IOUT_3 DESCRIPTION Upstream USB electrical signaling drive strength boost bit for downstream port 3. 00 01 10 11 3:2 no boost - low (approximately 4% boost) - medium (approximately 8% boost) - high (approximately 12% boost) BOOST_IOUT_2 : : : : normal electrical drive strength elevated electrical drive strength elevated electrical drive strength elevated electrical drive strength Upstream USB electrical signaling drive strength boost bit for downstream port 2. 00 01 10 11 : : : : normal electrical drive strength elevated electrical drive strength elevated electrical drive strength elevated electrical drive strength Note: 1:0 Revision 1.3 (05-17-11) rsvd no boost - low (approximately 4% boost) - medium (approximately 8% boost) - high (approximately 12% boost) no boost - low (approximately 4% boost) - medium (approximately 8% boost) - high (approximately 12% boost) Boost could result in non-USB compliant parameters. Therefore, a value of 00 should be implemented unless specific implementation issues require additional signal boosting to correct for degraded USB signalling levels. Always read as 0 42 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.4.20 F1h: Port Swap BIT BYTE NAME DESCRIPTION 7:0 PRT_SWP Port Swap: swaps the upstream and downstream USB DP and DM pins for ease of board routing to devices and connectors. 0 : USB D+ functionality is associated with the DP pin and D- functionality is associated with the DM pin. 1 : USB D+ functionality is associated with the DM pin and D- functionality is associated with the DP pin. Bit Bit Bit Bit Bit Bit Bit Bit SMSC USB4640/USB4640i 7 6 5 4 3 2 1 0 : : : : : : : : rsvd rsvd rsvd rsvd controls physical port 3 controls physical port 2 rsvd controls physical port 0 43 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.4.21 F2h: Port Map 12 BIT BYTE NAME DESCRIPTION 7:0 PRTM12 PortMap Register for Ports 1 and 2: when a hub is enumerated by a USB host controller, the hub is only permitted to report how many ports it has; the hub is not permitted to select a numerical range or assignment. The host controller will number the downstream ports of the hub starting with the number 1, up to the number of ports that the hub reports having. The host's port number is called the Logical Port Number and the physical port on the hub is the Physical Port Number. When mapping mode is enabled (see PORTMAP12.PRTMAP_EN) the hub's downstream port numbers can be mapped to different logical port numbers (assigned by the host). Note: Contiguous logical port numbers must be implemented, starting from number 1 up to the maximum number of enabled ports. This ensures that the hub's ports are numbered in accordance with the way a host will communicate with the ports. Bit [7:4] Bit [3:0] 0000 Physical port 2 is disabled 0001 Physical port 2 is mapped to logical port 1 0010 Physical port 2 is mapped to logical port 2 0011 Physical port 2 is mapped to logical port 3 0100 to 1111 Illegal; do not use 0000 Physical port 1 is disabled 0001 Physical port 1 is mapped to logical port 1 0010 Physical port 1 is mapped to logical port 2 0011 Physical port 1 is mapped to logical port 3 0100 to 1111 Illegal; do not use Table 4.5 Port Map Register for Ports 1 and 2 Revision 1.3 (05-17-11) 44 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.4.22 F3h: Port Map 3 BIT BYTE NAME DESCRIPTION 7:0 PRTM3 PortMap Register for Ports 1 and 2: when a hub is enumerated by a USB host controller, the hub is only permitted to report how many ports it has; the hub is not permitted to select a numerical range or assignment. The host controller will number the downstream ports of the hub starting with the number 1, up to the number of ports that the hub reports having. The host's port number is called the Logical Port Number and the physical port on the hub is the Physical Port Number. When mapping mode is enabled (see PORTMAP12.PRTMAP_EN: Configuration Data Byte 3) the hub's downstream port numbers can be remapped to different logical port numbers (assigned by the host). Note: Contiguous logical port numbers must be implemented, starting from number 1 up to the maximum number of enabled ports. This ensures that the hub's ports are numbered in accordance with the way a host will communicate with the ports. Bit [7:4] Bit [3:0] 0000 rsvd 0001 rsvd 0010 rsvd 0011 rsvd 0100 to 1111 Illegal; do not use 0000 Physical port 3 is disabled 0001 Physical port 3 is mapped to logical port 1 0010 Physical port 3 is mapped to logical port 2 0011 Physical port 3 is mapped to logical port 3 0100 to 1111 Illegal; do not use Table 4.6 Port Map Register for Port 3 4.4.4.23 F4h-F6h: Reserved BYTE BYTE NAME 6:0 rsvd SMSC USB4640/USB4640i DESCRIPTION . 45 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.4.24 F7h-FBh: Not Applicable BIT BYTE NAME 7:0 N/A 4.4.4.25 DESCRIPTION FCh-FFh: Non-Volatile Storage Signature BYTE NAME DESCRIPTION 3:0 NVSTORE_SIG This signature is used to verify the validity of the data in the first 256 bytes of the configuration area. The signature must be set to ATA2 for USB4640/USB4640i. 4.4.5 Internal Flash Media Controller Extended Configurations Enable registers 100h-17Fh by setting bit 7 of bmAttribute. 4.4.5.1 100h-106h: Combo LUN 0 Identifier String BYTE NAME DESCRIPTION 6:0 CLUN0_ID_STR If the device to LUN mapping bytes have configured this LUN to be a combo LUN, then these strings will be used to identify the LUN rather than the device identifier strings. 4.4.5.2 107h-17Bh: Not Applicable BYTE NAME 116:0 N/A 4.4.5.3 DESCRIPTION 17Ch -17Fh: Non-Volatile Storage Signature for Extended Configuration BYTE NAME DESCRIPTION 3:0 NVSTORE_SIG2 This signature is used to verify the validity of the data in the upper 256 bytes if a 512 byte EEPROM is used, otherwise this bank is a read-only configuration area. The signature must be set to ecf1. 4.4.6 I2C EEPROM The I2C EEPROM interface implements a subset of the I2C Master Specification (refer to I2C-Bus Specification [6] for I2C bus protocols). The device's I2C EEPROM interface is designed to attach to a single dedicated I2C EEPROM, and it conforms to the Standard-mode I2C Specification (100 kbps transfer rate and 7-bit addressing) for protocol and electrical compatibility. Note: Extensions to the I2C Specification are not supported. The device acts as the master and generates the serial clock SCL, controls the bus access (determines which device acts as the transmitter and which device acts as the receiver), and generates the START and STOP conditions. Revision 1.3 (05-17-11) 46 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 4.4.6.1 Protocol Implementation The hub will only access an EEPROM using the sequential read protocol as outlined in Chapter 8 of the MicroChip 24AA02/24LC02B Data Sheet [8]. 4.4.6.2 Pull-Up Resistor The circuit board designer is required to place external pull-up resistors (10 k recommended) on the SPI_DO/GPIO5/SDA/SPI_SPD_SEL and SPI_CLK/GPIO4/SCL lines (per SMBus 1.0 Specification [7] and EEPROM manufacturer guidelines) to VDD33 in order to assure proper operation. 4.4.7 In-Circuit EEPROM Programming The EEPROM can be programmed via automatic test equipment (ATE). Pulling nRESET low tri-states the device's EEPROM interface and allows an external source to program the EEPROM. 4.5 Default Configuration Option The SMSC device can be configured via its internal default configuration. Please see Section 4.3.2 on page 26 for specific details on how to enable default configuration. Please refer to Table 4.1 for the internal default values that are loaded when this option is selected. 4.5.1 External Hardware nRESET A valid hardware reset is defined as assertion of nRESET for a minimum of 1 s after all power supplies are within operating range. While reset is asserted, the device (and its associated external circuitry) consumes less than 500 A of current. Assertion of nRESET (external pin) causes the following: 1. All downstream ports are disabled and PRTCTL power to downstream devices is removed 2. The PHYs are disabled and the differential pairs will be in a high-impedance state 3. All transactions immediately terminate; no states are saved 4. All internal registers return to the default state (in most cases, 00h) 5. The external crystal oscillator is halted 6. The PLL is halted 4.5.1.1 nRESET for EEPROM Configuration Hardware reset asserted Device Recovery/ Stabilization 8051 Sets Configuration Registers Attach USB Upstream USB Reset recovery Idle Start completion request response t4 t1 t2 t3 t5 t6 t7 nRESET VSS Figure 4.1 nRESET Timing for EEPROM Mode SMSC USB4640/USB4640i 47 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Table 4.7 nRESET Timing for EEPROM Mode NAME DESCRIPTION MIN t1 nRESET asserted t2 Device recovery/stabilization t3 8051 programs device configuration t4 USB attach (Note) t5 Host acknowledges attach and signals USB reset t6 USB idle t7 Completion time for requests (with or without data stage) TYP MAX UNITS sec 1 20 500 sec 50 msec 100 msec 100 msec Undefined msec 5 msec Note: All power supplies must have reached the operating levels mandated in Chapter 6 on page 51, prior to (or coincident with) the assertion of nRESET. 4.5.2 USB Bus Reset In response to the upstream port signaling a reset to the device, the device does the following: 1. Sets default address to 0 2. Sets configuration to: Unconfigured 3. Negates PRTCTL[3:2] to all downstream ports 4. Clears all TT buffers 5. Moves device from suspended to active (if suspended) 6. Complies with Section 11.10 of the USB 2.0 Specification for behavior after completion of the reset sequence Note: The device does not propagate the upstream USB reset to downstream devices. The host then configures the device and the device's downstream port devices in accordance with the USB 2.0 Specification. Revision 1.3 (05-17-11) 48 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Chapter 5 AC Specifications 5.1 Oscillator/Crystal Parallel Resonant, Fundamental Mode, 24 MHz 350 ppm. Figure 5.1 Typical Crystal Circuit Table 5.1 Crystal Circuit Legend SYMBOL DESCRIPTION IN ACCORDANCE WITH C0 Crystal shunt capacitance CL Crystal load capacitance CB Total board or trace capacitance OEM board design CS Stray capacitance SMSC IC and OEM board design CXTAL XTAL pin input capacitance SMSC IC C1 Load capacitors installed on OEM board Calculated values based on Figure 5.2: Capacitance Formulas (See Note 5.2) C2 Crystal manufacturer's specification (See Note 5.1) C1 = 2 x (CL - C0) - CS1 C2 = 2 x (CL - C0) - CS2 Figure 5.2 Capacitance Formulas Note 5.1 C0 is usually included (subtracted by the crystal manufacturer) in the specification for CL and should be set to `0' for use in the calculation of the capacitance formulas in Figure 5.2: Capacitance Formulas. However, the PCB may present a parasitic capacitance between XTAL1 and XTAL2 . For an accurate calculation of C 1 and C 2, take the parasitic capacitance between traces XTAL1 and XTAL2 into account. Note 5.2 Each of these capacitance values is typically approximately 18 pF. SMSC USB4640/USB4640i 49 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 5.2 Ceramic Resonator 24 MHz 350 ppm Figure 5.3 Ceramic Resonator Usage with SMSC IC 5.3 External Clock 50% Duty cycle 10%, 24 MHz 350 ppm, Jitter < 100 ps rms. The external clock is recommended to conform to the signaling level designated in the JESD76-2 Specification on 1.8 V CMOS Logic. XTAL2 should be treated as a no connect. 5.3.1 I2C EEPROM Frequency is fixed at 58.6 kHz 20% 5.3.2 USB 2.0 The SMSC device conforms to all voltage, power, and timing characteristics and specifications as set forth in the USB 2.0 Specification. Please refer to the USB 2.0 Specification for more information. Revision 1.3 (05-17-11) 50 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Chapter 6 DC Parameters 6.1 Maximum Guaranteed Ratings PARAMETER SYMBOL Storage Temperature TSTOR MIN -55 MAX 150 UNITS COMMENTS C Lead Temperature C 1.2 V supply voltage VDD12 -0.5 1.5 V 3.3 V supply voltage VDD33 -0.5 4.0 V Voltage on USB+ and USB- pins -0.5 (3.3 V supply voltage + 2) 6 V Voltage on GPIO10 -0.5 VDD33 + 0.3 V Voltage on any signal pin -0.5 VDD33 + 0.3 V Voltage on XTAL1 -0.5 3.6 V Voltage on XTAL2 -0.5 2.0 V Refer to JEDEC Specification J-STD-020D [5]. When internal power FET operation of these pins are enabled, these pins may be simultaneously shorted to ground or any voltage up to 3.63 V indefinitely, without damage to the device as long as VDD33 is less than 3.63 V and TA is less than 70oC. Notes: Stresses above the specified parameters could cause permanent damage to the device. This is a stress rating only. Therefore, functional operation of the device at any condition above those indicated in the operation sections of this specification are not implied. When powering this device from laboratory or system power supplies, it is important that the absolute maximum ratings not be exceeded or device failure can result. Some power supplies exhibit voltage spikes on their outputs when the AC power is switched on or off. In addition, voltage transients on the AC power line may appear on the DC output. When this possibility exists, it is suggested that a clamp circuit be used. SMSC USB4640/USB4640i 51 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 6.2 Operating Conditions PARAMETER SYMBOL MIN MAX UNITS Comments Commercial USB4640 Operating Temperature TA 0 70 C Ambient temperature in still air. Industrial USB4640i Operating Temperature TA -40 85 C Ambient temperature in still air. 1.2 V supply voltage VDD12 1.1 1.3 V The ripple on VDD12 must be less than 50 mV peak to peak. 1.2 V supply rise time tRT12 0 400 s Under all conditions the voltage on the 1.2 V supply must be below the 3.3 V supply. (Figure 6.1) 3.3 V supply voltage VDD33 3.0 3.6 V A 3.3 V regulator with an output tolerance of 1% must be used if the output of the internal power FET's must support a 5% tolerance. 3.3 V supply rise time tRT33 0 400 s (Figure 6.1) -0.3 5.5 V If any 3.3 V supply voltage drops below 3.0 V, then the MAX becomes: Voltage on USB+ and USB- pins (3.3 V supply voltage) + 0.5 5.5 Voltage on any signal pin -0.3 VDD33 V Voltage on XTAL1 -0.3 2.0 V Voltage on XTAL2 -0.3 2.0 V Voltage tRTxx VDD33 3.3 V 100% 90% 1.2 V VDD12 100% 90% VSS 10% t90% t10% Time Figure 6.1 Supply Rise Time Model Revision 1.3 (05-17-11) 52 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 6.3 DC Electrical Characteristics PARAMETER SYMBO L MIN TYP MAX UNITS 0.8 V COMMENTS I, IPU, IPD Type Input Buffer Low Input Level VILI High Input Level VIHI Pull Down PD 72 A Pull Up PU 58 A 2.0 TLL Levels V IS Type Input Buffer Low Input Level VILI High Input Level VIHI Hysteresis 0.8 2.0 TTL Levels V 420 VHYSI V mV ICLK Input Buffer Low Input Level VILCK High Input Level VIHCK 1.4 IIL -10 +10 A VIN = 0 to VDD33 Low Input Leakage IIL -10 +10 A VIN = 0 High Input Leakage IIH -10 +10 A VIN = VDD33 0.4 V IOL = 6 mA @ VDD33 = 3.3 V V IOH = -6 mA @ VDD33 = 3.3 V A VIN = 0 to VDD33 (Note 6.1) Input Leakage 0.5 V V Input Leakage (All I and IS buffers) I/O6, I/OD6PU Type Buffers Low Output Level VOL High Output Level VOH VDD33 -0.4 Output Leakage IOL -10 Pull Down PD 72 A Pull Up PU 58 A SMSC USB4640/USB4640i 53 DATASHEET +10 Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet PARAMETER SYMBO L MIN TYP MAX UNITS COMMENTS O8, O8PD, 08PU, I/O8, I/O8PD, and I/O8PU Type Buffers Low Output Level VOL High Output Level VOH VDD33 - 0.4 Output Leakage IOL -10 Pull Down PD 72 A Pull Up PU 58 A +10 V IOL = 8 mA @ VDD33 = 3.3 V V IOH = -8 mA @ VDD33 = 3.3 V A VIN = 0 to VDD33 (Note 6.1) O12, I/O12, and I/O12PD Type Buffers 0.4 V IOL = 12 mA @ VDD33 = 3.3 V V IOH = -12 mA @ VDD33 = 3.3 V A VIN = 0 to VDD33 (Note 6.1) Low Output Level VOL High Output Level VOH VDD33 - 0.4 Output Leakage IOL -10 Pull Down PD 72 A Pull Up PU 58 A +10 IO-U (Note 6.2) I-R (Note 6.3) I/O200 Integrated Power FET for GPIO10 High Output Current IOUT 200 mA VdropFET = 0.46 V Low Output Current (Note 6.4) IOUT 100 mA VdropFET = 0.23 V On Resistance (Note 6.4) RDSON 2.1 IFET = 70 mA Output Voltage Rise Time tDSON 800 s CLOAD = 10 F mA VdropFET = 0.22 V Integrated Power FET Set to 100 mA Output Current (Note 6.4) IOUT Short Circuit Current Limit ISC 140 mA VoutFET = 0 V On Resistance (Note 6.4) RDSON 2.1 IFET = 70 mA Output Voltage Rise Time tDSON 800 s CLOAD = 10 F Revision 1.3 (05-17-11) 100 54 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet SYMBO L MIN Output Current (Note 6.4) IOUT 200 Short Circuit Current Limit ISC On Resistance (Note 6.4) Output Voltage Rise Time PARAMETER TYP MAX UNITS COMMENTS mA VdropFET = 0.46 V 181 mA VoutFET = 0 V RDSON 2.1 IFET = 70 mA tDSON 800 s CLOAD = 10 F Integrated Power FET Set to 200 mA Supply Current Unconfigured (Note 6.6) USB4640 ICCINTHS 58 60 mA USB4640i ICCINTHS 58 62 mA Supply Current Configured 1 downstream port (Note 6.6) USB4640 IHCH1 155 160 mA USB4640i IHCH1 155 165 mA Supply Current Configured Each additional downstream port (Note 6.6) USB4640 30 35 mA USB4640i 30 40 mA 46 60 HSIC_DAT, HSIC_STROBE Driver Impedance ID 40 Supply Current Suspend (Note 6.5) (Note 6.6) USB4640 ICSBY 210 375 A USB4640i ICSBY 210 450 A Supply Current Reset (Note 6.6) USB4640 IRST 220 400 A USB4640i IRST 220 500 A Note 6.1 Output leakage is measured with the current pins in high impedance. Note 6.2 See the USB 2.0 Specification, Chapter 7, for USB DC electrical characteristics Note 6.3 RBIAS is a 3.3 V tolerant analog pin. Note 6.4 Output current range is controlled by program software. The software disables the FET during short circuit condition. Note 6.5 Refer to the High-Speed Inter-Chip USB Electrical Specification Revision 1.0 [2]. Note 6.6 Typical and maximum values were characterized using the following temperature ranges: The USB4640 supports the commercial temperature range of 0C to +70C The USB4640i supports the industrial temperature range of -40C to +85C SMSC USB4640/USB4640i 55 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 6.4 Capacitance TA = 25C; fc = 1 MHz; VDD33 = 3.3 V Table 6.1 Pin Capacitance LIMITS PARAMETER Clock Input Capacitance Input Capacitance Output Capacitance Revision 1.3 (05-17-11) SYMBOL MIN TYP MAX UNIT TEST CONDITION CXTAL 2 pF All pins (except USB pins and pins under test) are tied to AC ground. CIN 10 pF COUT 20 pF 56 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Chapter 7 GPIO Usage Table 7.1 USB4640/USB4640i GPIO Usage NAME ACTIVE LEVEL GPIO1 H LED / TxD LED indicator / Serial port transmit line GPIO2 H RxD Serial port receive line GPIO4 H SCL Serial EEPROM clock GPIO5 H SDA Serial EEPROM data GPIO6 L SD_WP Secure Digital card write protect assertion GPIO10 L CRD_PWR_CTRL Card power control GPIO12 L MS_nCD Memory Stick card detect GPIO14 L xD_nCD xD-Picture card detect GPIO15 L SD_nCD Secure Digital card detect SMSC USB4640/USB4640i SYMBOL 57 DATASHEET DESCRIPTION AND NOTE Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Chapter 8 Package Specifications Figure 8.1 USB4640/USB4640i 48-Pin QFN Revision 1.3 (05-17-11) 58 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet 8.1 Tape and Reel Specifications Figure 8.2 48-Pin Package Tape Specifications SMSC USB4640/USB4640i 59 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Figure 8.3 48-Pin Package Reel Specifications Revision 1.3 (05-17-11) 60 DATASHEET SMSC USB4640/USB4640i High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Appendix A (Acronyms) ACK: Handshake packet (positive acknowledgement) EOF: End of (micro) Frame FM: Flash Media FMC: Flash Media Controller FS: Full-Speed Device LS: Low-Speed Device HS: Hi-Speed Device I2C(R): Inter-Integrated Circuit1 MMC: MultiMediaCard MS: Memory Stick MSC: Memory Stick Controller OCS: Over-current Sense PHY: Physical Layer PLL: Phase-Locked Loop SD: Secure Digital SDC: Secure Digital Controller TXD: Transmit eXchange Data UART: Universal Asynchronous Receiver-Transmitter UCHAR: Unsigned Character UINT: Unsigned Integer Standard Microsystems is a registered trademark and SMSC is a trademark of Standard Microsystems Corporation. Other product and company names are trademarks or registered trademarks of their respective holders. *Note: In order to develop, make, use, or sell readers and/or other products using or incorporating any of the SMSC devices made the subject of this document or to use related SMSC software programs, technical information and licenses under patent and other intellectual property rights from or through various persons or entities, including without limitation media standard companies, forums, and associations, and other patent holders may be required. These media standard companies, forums, and associations include without limitation the following: Sony Corporation (Memory Stick, Memory Stick Pro); SD3 LLC (Secure Digital); MultiMedia Card Association (MultiMediaCard); the SSFDC Forum (SmartMedia); the Compact Flash Association (Compact Flash); and Fuji Photo Film Co., Ltd., Olympus Optical Co., Ltd., and Toshiba Corporation (xD-Picture Card). SMSC does not make such licenses or technical information available; does not promise or represent that any such licenses or technical information will actually be obtainable from or through the various persons or entities (including the media standard companies, forums, and associations), or with respect to the terms under which they may be made available; and is not responsible for the accuracy or sufficiency of, or otherwise with respect to, any such technical information. SMSC's obligations (if any) under the Terms of Sale Agreement, or any other agreement with any customer, or otherwise, with respect to infringement, including without limitation any obligations to defend or settle claims, to reimburse for costs, or to pay damages, shall not apply to any of the devices made the subject of this document or any software programs related to any of such devices, or to any combinations involving any of them, with respect to infringement or claimed infringement of any existing or future patents related to solid state disk or other flash memory technology or applications ("Solid State Disk Patents"). By making any purchase of any of the devices made the subject of this document, the customer represents, warrants, and agrees that it has obtained all necessary licenses under then-existing Solid State Disk Patents for the manufacture, use and sale of solid state disk and other flash memory products and that the customer will timely obtain at no cost or expense to SMSC all necessary licenses under Solid State Disk Patents; that the manufacture and testing by or for SMSC of the units of any of the devices made the subject of this document which may be sold to the customer, and any sale by SMSC of such units to the customer, are valid exercises of the customer's rights and licenses under such Solid State Disk Patents; that SMSC shall have no obligation for royalties or otherwise under any Solid State Disk Patents by reason of any such manufacture, use, or sale of such units; and that SMSC shall have no obligation for any costs or expenses related to the customer's obtaining or having obtained rights or licenses under any Solid State Disk Patents. SMSC MAKES NO WARRANTIES, EXPRESS, IMPLIED, OR STATUTORY, IN REGARD TO INFRINGEMENT OR OTHER VIOLATION OF INTELLECTUAL PROPERTY RIGHTS. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES AGAINST INFRINGEMENT AND THE LIKE. No license is granted by SMSC expressly, by implication, by estoppel or otherwise, under any patent, trademark, copyright, mask work right, trade secret, or other intellectual property right. **To obtain this software program the appropriate SMSC Software License Agreement must be executed and in effect. Forms of these Software License Agreements may be obtained by contacting SMSC. 1. I2C is a registered trademark of Philips Corporation. SMSC USB4640/USB4640i 61 DATASHEET Revision 1.3 (05-17-11) High-Speed Inter-Chip (HSIC) USB 2.0 Hub and Flash Media Controller Datasheet Appendix B (References) [1] Universal Serial Bus Specification, Version 2.0, April 27, 2000 (12/7/2000 and 5/28/2002 Errata) USB Implementers Forum, Inc. http://www.usb.org [2] USB 2.0 Supplement High-Speed Inter-Chip USB Electrical Specification Revision 1.0. 09/23/07. USB Implementers Forum, Inc. http://www.usb.org/developers/docs/ [3] HSIC ECN. May 25, 2010 USB Implementers Forum, Inc. http://www.usb.org/developers/docs/ [4] The Unicode Standard, Worldwide Character Encoding Version 4.0 The Unicode Consortium. http://www.unicode.org [5] JEDEC Specification J-STD-020D JEDEC Global Standards for the Microelectronics Industry.http://www.jedec.org/standards-documents [6] I2C-Bus Specification Version 1.1 NXP (formerly a division of Philips). http://www.nxp.com/products/interface_control/i2c/ [7] System Management Bus Specification, version 1.0 SMBus. http://smbus.org/specs/ [8] MicroChip 24AA02/24LC02B Microchip Technology Inc. http://www.microchip.com/ Revision 1.3 (05-17-11) 62 DATASHEET SMSC USB4640/USB4640i