Chip tantalum capacitors (Bottom surface electrode type : Large capacitance) TC Series M Case Features (M) With an original bottom surface electrode structure. 1) Excellent adhesion. 2) Easy visual recognition of fillets. 3) Large capacitance, low ESR. Dimensions (Unit : mm) Anode mark (Unit : mm) Dimensions M case L 1.6 + - 0.1 W1 0.85 + - 0.1 W2 0.55 + - 0.1 H 0.8 + - 0.1 S 0.5 + - 0.1 H L + - Part No. Explanation T C M 1 A 1 2 3 4 7 5 4 M 8 R 5 6 4 Nominal capacitance 1 Series name Nominal capacitance in pF in 3 digits: 2 significant figures followed by the figure representing the number of 0's. TC 2 Case style M 5 Capacitance tolerance 3 Rated voltage Rated voltage (V) CODE 2.5 4 6.3 10 16 0E 0G 0J 1A 1C M: + - 20% 6 Taping 8 : Tape width R : Positive electrode on the side opposite to sprocket hole www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. 1/6 2011.11 - Rev.H TC Series M Case Data Sheet Rated table Rated voltage (V) (F) 2.5 0E 4 0G 6.3 0J 10 1A 16 1C M M M M M M M M M 1.0 (105) 20 1D 25 1E M 1.5 (155) 2.2 (225) M 3.3 (335) 4.7 (475) 6.8 (685) M 10 (106) 15 (156) 22 (226) M M 33 (336) M M M 47 (476) Remark) Case size codes (M) in the above show products line-up. Under development Marking The indications listed below should be given on the surface of a capacitor. : The polarity should be shown by bar. (on the anode side) (1) Polarity (2) Rated DC voltage : Due to the small size of M case, a voltage code is used as shown below. (3) Visual typical example (1) voltage code (2) capacitance code Rated DC Voltage (V) 2.5 Capacitance Code A Nominal Capacitance (F) 1.0 g 4 E 1.5 j 6.3 J 2.2 A 10 N 3.3 C 16 S 4.7 D 20 W 6.8 E 25 a 10 e 15 Voltage Code e [M case] note 1) j 22 n 33 s 47 A s - - (1) (2) As note 2) voltage code and capacitance code are variable with parts number www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. 2/6 2011.11 - Rev.H TC Series M Case Data Sheet Characteristics Performance Item Operating Temperature -55C to +125C Maximum operating temperature with no voltage derating +85C Test conditions (based on JIS C 5101-1 and JIS C 5101-3) Voltage reduction when temperature exceeds +85C Rated voltage (VDC) 2.5 4 6.3 10 16 20 25 at 85C Category voltage (VDC) 1.6 2.5 4 6.3 10 13 16 at 125C Surge voltage (VDC) 3.2 5.2 8 13 20 26 32 at 85C DC Leakage current Shall be satisfied the voltage on " Standard list " As per 4.9 JIS C 5101-1 As per 4.5.1 JIS C 5101-3 Voltage : Rated voltage for 5min Capacitance tolerance Shall be satisfied allowance range. 20% As per 4.7 JIS C 5101-1 As per 4.5.2 JIS C 5101-3 Measuring frequency : 12012Hz Measuring voltage : 0.5Vrms +1.5.DC Measuring circuit : DC Equivalent series circuit Tangent of loss angle (Df, tan ) Shall be satisfied the voltage on " Standard list " As per 4.8 JIS C 5101-1 As per 4.5.3 JIS C 5101-3 Measuring frequency : 12012Hz Measuring voltage : 0.5Vrms +1.5.DC Measuring circuit : DC Equivalent series circuit Impedance Shall be satisfied the voltage on " Standard list " As per 4.10 JIS C 5101-1 As per 4.5.4 JIS C 5101-3 Measuring frequency : 10010kHz Measuring voltage : 0.5Vrms or less Measuring circuit : DC Equivalent series circuit Appearance There should be no significant abnormality. The indications should be clear. L.C. Less than 200% of initial limit C / C TCM0J336 : Within 30% of initial value. Others : Within 20% of initial value. Df (tan ) Less than 200% of initial limit As per 4.14 JIS C 5101-1 As per 4.6 JIS C 5101-3 Dip in the solder bath Solder temp : 2605C Duration : 50.5s Repetition :1 After the specimens, leave it at room temperature for over 24h and then measure the sample. Appearance There should be no significant abnormality. The indications should be clear. L.C. Less than 200% of initial limit C / C TCM0J336 : Within 30% of initial value. Others : Within 20% of initial value. Temp. Time 1 -55 + - 3C 303min. Less than 200% of initial limit 2 Room temp. + 2C 125 - 3min.or less Resistance to Soldering heat Temperature cycle Df (tan ) As per 4.16 JIS C 5101-1 As per 4.10 JIS C 5101-3 Repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation. 3 303min. 4 Room temp. 3min.or less After the specimens, leave it at room temperature for over 24h and then measure the sample. Moisture resistance Appearance There should be no significant abnormality. The indications should be clear. L.C. Less than 200% of initial limit C / C TCM0J336 : Within 30% of initial value. Others : Within 20% of initial value. Df (tan ) Less than 200% of initial limit www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. 3/6 As per 4.22 JIS C 5101-1 As per 4.12 JIS C 5101-3 After leaving the sample under such atmospheric condition that the temperature and humidity are 602C and 90 to 95% RH,respectiveiy, for 50012h leave it at room temperature for over 24h and then measure the sample. 2011.11 - Rev.H TC Series M Case Data Sheet Performance Item Temperature Stability Temp. -55C C / C TCM0G336 : Within 0/-30% of initial value TCM0J226 : Within 0/-30% of initial value TCM0J336 : Within 0/-30% of initial value Others : Within 0/-15% of initial value Df (tan ) Shall be satisfied the voltage on " Standard list " Temp. +85C C / C TCM0G336 : Within +15/-5% of initial value TCM0J226 : Within 15/-5% of initial value TCM0J336 : Within 15/-5% of initial value Others : Within +15/0% of initial value Df (tan ) Shall be satisfied the voltage on " Standard list " L.C. Less than 1000% of initial value Temp. +125C C / C TCM0G336 : Within +20/-5% of initial value Others : Within +20/0% of initial value Df (tan ) Shall be satisfied the voltage on " Standard list " L.C. Less than 1000% of initial value Appearance There should be no significant abnormality. L.C. Less than 200% of initial limit C / C Within 20% of initial value Df (tan ) Less than 200% of initial limit Appearance Loading at High temperature L.C. Terminal strength As per 4.29 JIS C 5101-1 As per 4.13 JIS C 5101-3 - L.C. Surge voltage Test conditions (based on JIS C 5101-1 and JIS C 5101- 3) There should be no significant abnormality. Less than 200% of initial limit C / C TCM0G336 : Within 30% of initial value TCM0J226 : Within 30% of initial value TCM0J336 : Within 30% of initial value Others : Within 20% of initial value Df (tan ) Less than 200% of initial limit Capacitance The measured value should be stable. Appearance There should be no significant abnormality. As per 4.26JIS C 5101-1 As per 4.14JIS C 5101-3 Apply the specified surge voltage every 50.5 min. for 305 s. each time in the atmospheric condition of 852C. Repeat this procedure 1,000 times. After the specimens, leave it at room temperature for over 24h and then measure the sample. As per 4.23 JIS C 5101-1 As per 4.15 JIS C 5101-3 After applying the rated voltage for 1000+36/0 h without discontinuation via the serial resistance of 3 or less at a temperature of 852C, leave the sample at room temperature / humidity for over 24h and measure the value. As per 4.35 JIS C 5101-1 As per 4.9 JIS C 5101-3 A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintain the condition for 5s. (See the figure below) (Unit : mm) 50 20 F (Apply force) R230 1 thickness=1.6mm 45 www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. 4/6 45 2011.11 - Rev.H TC Series M Case Data Sheet Performance Item Adhesiveness Test conditions (JIS C 5101-1 and JIS C 5101- 3) As per 4.34 JIS C 5101-1 As per 4.8 JIS C 5101-3 Apply force of 5N in the two directions shown in the figure below for 101s after mounting the terminal on a circuit board. The terminal should not come off. product YAA C105 Apply force a circuit board Dimensions Refer to "External dimensions" Measure using a caliper of JIS B 7507 Class 2 or higher grade. Resistance to solvents The indication should be clear As per 4.32 JIS C 5101-1 As per 4.18 JIS C 5101-3 Dip in the isopropyl alcohol for 305s, at room temperature. Solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. As per 4.15.2 JIS C 5101-1 As per 4.7 JIS C 5101-3 Dip speed=252.5mm / s Pre-treatment(accelerated aging): Leave the sample on the boiling distilled water for 1 h. Solder temp. : 2455C Duration : 30.5s Solder : M705 Flux : Rosin 25% IPA 75% Vibration Capacitance Measure value should not fluctuate during the measurement. Appearance There should be no significant abnormality. As per 4.17 JIS C 5101-1 Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board. Standard products list, TC series M case Part No. TC M 0E 476 Rated voltage 85C Category voltage 125C Surge voltage 85C (V) (V) (V) 2.5 1.6 3.2 Cap. 120Hz (F) Df Impedance Leakage 120Hz 100kHz current (%) Tolerance 25C (%) 1WV.300s 25C 125C -55C () (A) 85C 4.7 + - 20 0.5 30 20 30 9.0 TC M 0G 106 4 2.5 5.2 10 + - 20 0.5 30 20 30 9.0 TC M 0G 226 4 2.5 5.2 22 + - 20 0.9 30 20 30 9.0 TC M 0G 336 4 2.5 5.2 33 + 20 13.0 60 30 40 9.0 TC M 0J 475 6.3 4 8 4.7 + - 20 0.5 30 20 30 9.0 TC M 0J 106 6.3 4 8 10 + - 20 0.6 30 20 30 9.0 TC M 0J 226 6.3 4 8 22 + - 20 13.0 60 30 40 9.0 TC M 0J 336 6.3 4 8 33 + - 20 208 60 30 40 9.0 TC M 1A 105 10 6.3 13 1.0 + - 20 0.5 15 10 15 15.0 TC M 1A 225 10 6.3 13 2.2 + - 20 0.5 30 20 30 13.5 TC M 1A 475 10 6.3 13 4.7 + - 20 0.5 30 20 30 9.0 TC M 1A 106 10 6.3 13 10 + - 20 10.0 30 20 30 9.0 0.5 15 10 15 15.0 0.5 30 20 30 13.5 TC M 1C 105 16 10 20 1.0 + - 20 TC M 1C 225 16 10 20 2.2 + - 20 + 20% ) =Tolerance (M : - www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. 5/6 2011.11 - Rev.H TC Series M Case Data Sheet Packaging specifications (Unit : mm) A+ -0.1 t1 + - 0.1 -0.1 W+ - 0.2 E+ -0.1 F + -0.05 P1+ - 0.05 P0+ - 0.05 t2 + -0.1 P2 + -0.1 B+ Case code 1.0 M 1.8 8.0 1.75 3.5 4.0 2.0 4.0 0.20 1.0 Taping [M case] t1 1.5 +0.1 0 E A F W B t2 P1 P2 P0 Feeding direction Packaging style Case code Packaging M case Taping Packaging style Symbol Basic ordering units 180mm Reel plastic taping R 4,000pcs +1.0 9.0 0 Reel [M case] 0 180-1.5 60 +1 0 13+ -0.2 11.4+ -1.0 Pull direction Label sticking position (Unit : mm) EIAJ ET-7200A www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. 6/6 2011.11 - Rev.H Notice Notes Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. R1120A