19-3196; Rev 0; 2/04 KIT ATION EVALU LE B A IL A AV Dual, 10-Bit, 80Msps, Current-Output DAC Applications Communications SatCom, LMDS, MMDS, HFC, DSL, WLAN, Point-to-Point Microwave Links Wireless Base Stations Quadrature Modulation Direct Digital Synthesis (DDS) Instrumentation/ATE 2.7V to 3.6V Single Supply Full Output Swing and Dynamic Performance at 2.7V Supply Superior Dynamic Performance 78dBc SFDR at fOUT = 20MHz Programmable Channel Gain Matching Integrated 1.24V Low-Noise Bandgap Reference Single-Resistor Gain Control Interleaved Data Mode Single-Ended and Differential Clock Input Modes Miniature 40-Pin Thin QFN Package, 6mm x 6mm EV Kit Available--MAX5854 EV Kit Ordering Information PART TEMP RANGE PIN-PACKAGE 40 Thin QFN-EP* MAX5853ETL -40C to +85C *EP = Exposed paddle. REFO REFR AVDD OUTNB OUTPB AGND TOP VIEW OUTPA Pin Configuration OUTNA The MAX5853 is packaged in a 40-pin thin QFN with exposed paddle (EP) and is specified for the extended (-40C to +85C) temperature range. Pin-compatible, higher speed, and lower resolution versions are also available. Refer to the MAX5854 (10-bit, 165Msps), the MAX5852** (8-bit, 165Msps), and the MAX5851** (8-bit, 80Msps) data sheets for more information. See Table 4 at the end of the data sheet. Low Power 77mW with IFS = 5mA at fCLK = 80MHz AVDD The MAX5853 can also operate in interleave data mode to reduce the I/O pin count. This allows the converter to be updated on a single, 10-bit bus. The MAX5853 features digital control of channel gain matching to within 0.4dB in sixteen 0.05dB steps. Channel matching improves sideband suppression in analog quadrature modulation applications. The onchip 1.24V bandgap reference includes a control amplifier that allows external full-scale adjustments of both channels through a single resistor. The internal reference can be disabled and an external reference may be applied for high-accuracy applications. The MAX5853 features full-scale current outputs of 2mA to 20mA and operates from a 2.7V to 3.6V single supply. The DAC supports three modes of power-control operation: normal, low-power standby, and complete powerdown. In power-down mode, the operating current is reduced to 1A. 10-Bit, 80Msps Dual DAC AGND The MAX5853 dual, 10-bit, 80Msps digital-to-analog converter (DAC) provides superior dynamic performance in wideband communication systems. The device integrates two 10-bit DAC cores, and a 1.24V reference. The converter supports single-ended and differential modes of operation. The MAX5853 dynamic performance is maintained over the entire 2.7V to 3.6V power-supply operating range. The analog outputs support a -1.0V to +1.25V compliance voltage. Features 40 39 38 37 36 35 34 33 32 31 30 CVDD DA9/PD 1 DA8/DACEN 2 DA7/IDE 3 28 CLK DA6/REN 4 27 CVDD DA5/G3 5 DA4/G2 6 DA3/G1 7 24 DCE DA2/G0 8 23 CW DA1 9 22 DB0 DA0 10 21 DB1 EP 29 CGND 26 CLKXN MAX5853 25 CLKXP DB2 DB3 DB4 DGND DB5 DVDD DB6 DB7 DB9 **Future product--contact factory for availability. DB8 11 12 13 14 15 16 17 18 19 20 THIN QFN ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX5853 General Description MAX5853 Dual, 10-Bit, 80Msps, Current-Output DAC ABSOLUTE MAXIMUM RATINGS OUTPA, OUTNA to AGND ..........(AVDD - 4.8V) to (AVDD + 0.3V) OUTPB, OUTNB to AGND ..........(AVDD - 4.8V) to (AVDD + 0.3V) Maximum Current into Any Pin (excluding power supplies) ..........................................50mA Continuous Power Dissipation (TA = +70C) 40-Pin Thin QFN (derate 26.3mW/C above +70C)....2105mW Operating Temperature Range ...........................-40C to +85C Storage Temperature Range .............................-65C to +150C Junction Temperature ......................................................+150C Lead Temperature (soldering, 10s) .................................+300C AVDD to AGND .........................................................-0.3V to +4V DVDD to DGND.........................................................-0.3V to +4V CVDD to CGND.........................................................-0.3V to +4V AVDD to DVDD .............................................................-4V to +4V AGND to DGND.....................................................-0.3V to +0.3V AGND to CGND.....................................................-0.3V to +0.3V DGND to CGND ....................................................-0.3V to +0.3V DA9-DA0, DB9-DB0, CW, DCE to DGND ...............-0.3V to +4V CLK to CGND ..........................................-0.3V to (CVDD + 0.3V) CLKXN, CLKXP to CGND.........................................-0.3V to +4V REFR, REFO to AGND .............................-0.3V to (AVDD + 0.3V) Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (AVDD = DVDD = CVDD = 3V, AGND = DGND = CGND = 0, fDAC = 80Msps, differential clock, external reference, VREF = 1.2V, IFS = 20mA, differential output, output amplitude = 0dBFS, TA = TMIN to TMAX, unless otherwise noted. TA +25C, guaranteed by production test. TA < +25C guaranteed by design and characterization. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS STATIC PERFORMANCE Resolution N 10 Bits Integral Nonlinearity INL RL = 0 -1.0 0.25 +1.0 LSB Differential Nonlinearity DNL Guaranteed monotonic, RL = 0 -0.5 0.2 +0.5 LSB Offset Error VOS -0.5 0.1 +0.5 LSB Internal reference (Note1) -11.0 1.5 +6.8 External reference -6.25 0.7 +4.10 Gain Error (See Also Gain Error Definition Section) GE Gain-Error Temperature Drift Internal reference 150 External reference 100 %FSR ppm/C DYNAMIC PERFORMANCE fCLK = 80MHz, AOUT = -1dBFS Spurious-Free Dynamic Range to Nyquist Spurious-Free Dynamic Range Within a Window Multitone Power Ratio to Nyquist 2 SFDR SFDR MTPR fOUT = 10MHz 69.5 78 fOUT = 20MHz 78 fOUT = 30MHz 72 fCLK = 44MHz, AOUT = -1dBFS fOUT = 10MHz 78 fCLK = 25MHz, AOUT = -1dBFS fOUT = 1MHz 79 fCLK = 80MHz, fOUT = 10MHz, AOUT = -1dBFS, span = 10MHz 85 fCLK = 65MHz, fOUT = 5MHz, AOUT = -1dBFS, span = 2.5MHz 82 fCLK = 25MHz, fOUT = 1MHz, AOUT = -1dBFS, span = 2MHz 82 8 tones at 400kHz spacing, fCLK = 78MHz, fOUT = 15MHz to 18.2MHz 74 _______________________________________________________________________________________ dBc dBc dBc Dual, 10-Bit, 80Msps, Current-Output DAC (AVDD = DVDD = CVDD = 3V, AGND = DGND = CGND = 0, fDAC = 80Msps, differential clock, external reference, VREF = 1.2V, IFS = 20mA, differential output, output amplitude = 0dBFS, TA = TMIN to TMAX, unless otherwise noted. TA +25C, guaranteed by production test. TA < +25C guaranteed by design and characterization. Typical values are at TA = +25C.) PARAMETER SYMBOL Multitone Spurious-Free Dynamic Range Within a Window CONDITIONS 8 tones at 811kHz spacing, fCLK = 80MHz, fOUT = 10.8MHz to 17.2MHz, span = 15MHz fCLK = 80MHz, AOUT = -1dBFS Total Harmonic Distortion to Nyquist (2nd- Through 8th-Order Harmonics Included) MIN THD fDAC -75 fOUT = 10MHz -76 fCLK = 25MHz, AOUT = -1dBFS fOUT = 1MHz -76 Channel-to-Channel Phase Mismatch Maximum DAC Conversion Rate -76 fOUT = 20MHz -70 Channel-to-Channel Gain Mismatch SNR fOUT = 10MHz fOUT = 30MHz fOUT = 10MHz tS UNITS dBc dBc 90 dB fOUT = 10MHz, G[3:0] = 1000 0.025 dB fOUT = 10MHz 0.05 Degrees fCLK = 80MHz, fOUT = 5MHz, IFS = 20mA 62 fCLK = 80MHz, fOUT = 5MHz, IFS = 5mA 62 Interleaved mode disabled, IDE = 0 80 Interleaved mode enabled, IDE = 1 80 Glitch Impulse Output Settling Time MAX 76 fCLK = 44MHz, AOUT = -1dBFS Output Channel-to-Channel Isolation Signal-to-Noise Ratio to Nyquist TYP dB Msps 5 pV-s ns To 0.1% error band (Note 3) 12 Output Rise Time 10% to 90% (Note 3) 2.2 ns Output Fall Time 90% to 10% (Note 3) 2.2 ns ANALOG OUTPUT Full-Scale Output Current Range IFS Output Voltage Compliance Range Output Leakage Current Shutdown or standby mode 2 20 mA -1.00 +1.25 V -5 +5 A 1.32 V REFERENCE Internal-Reference Output Voltage VREFO Internal-Reference Supply Rejection Internal-Reference OutputVoltage Temperature Drift TCVREFO REN = 0 1.13 1.24 AVDD varied from 2.7V to 3.6V 0.5 mV/V REN = 0 50 ppm/C _______________________________________________________________________________________ 3 MAX5853 ELECTRICAL CHARACTERISTICS (continued) MAX5853 Dual, 10-Bit, 80Msps, Current-Output DAC ELECTRICAL CHARACTERISTICS (continued) (AVDD = DVDD = CVDD = 3V, AGND = DGND = CGND = 0, fDAC = 80Msps, differential clock, external reference, VREF = 1.2V, IFS = 20mA, differential output, output amplitude = 0dBFS, TA = TMIN to TMAX, unless otherwise noted. TA +25C, guaranteed by production test. TA < +25C guaranteed by design and characterization. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS Internal-Reference Output Drive Capability REN = 0 External-Reference Input Voltage Range REN = 1 Current Gain MIN TYP MAX 50 0.10 IFS/IREF 1.2 UNITS A 1.32 32 V mA/mA LOGIC INPUTS (DA9-DA0, DB9-DB0, CW) Digital Input-Voltage High VIH Digital Input-Voltage Low VIL Digital Input Current IIN Digital Input Capacitance CIN 0.65 x DVDD V -1 0.3 x DVDD V +1 A 3 pF SINGLE-ENDED CLOCK INPUT/OUTPUT AND DCE INPUT (CLK, DCE) Digital Input-Voltage High VIH DCE = 1 Digital Input-Voltage Low VIL DCE = 1 Digital Input Current IIN DCE = 1 Digital Input Capacitance CIN DCE = 1 Digital Output-Voltage High VOH DCE = 0, ISOURCE = 0.5mA, Figure 1 Digital Output-Voltage Low VOL DCE = 0, ISINK = 0.5mA, Figure 1 0.65 x CVDD V -1 0.3 x CVDD V +1 A 3 pF 0.9 x CVDD V 0.1 x CVDD V DIFFERENTIAL CLOCK INPUTS (CLKXP/CLKXN) Differential Clock Input Internal Bias CVDD / 2 Differential Clock Input Swing V 0.5 Clock Input Impedance Measured single ended V 5 k POWER REQUIREMENTS Analog Power-Supply Voltage AVDD 2.7 3 3.6 V Digital Power-Supply Voltage DVDD 2.7 3 3.6 V Clock Power-Supply Voltage CVDD 2.7 3 3.6 V IFS = 20mA (Note 2), single-ended clock mode 43.2 46 IFS = 20mA (Note 2), differential clock mode 43.2 Analog Supply Current 4 IAVDD IFS = 2mA (Note 2), single-ended clock mode 5 IFS = 2mA (Note 2), differential clock mode 5 _______________________________________________________________________________________ mA Dual, 10-Bit, 80Msps, Current-Output DAC (AVDD = DVDD = CVDD = 3V, AGND = DGND = CGND = 0, fDAC = 80Msps, differential clock, external reference, VREF = 1.2V, IFS = 20mA, differential output, output amplitude = 0dBFS, TA = TMIN to TMAX, unless otherwise noted. TA +25C, guaranteed by production test. TA < +25C guaranteed by design and characterization. Typical values are at TA = +25C.) PARAMETER Digital Supply Current SYMBOL IDVDD TYP MAX IFS = 20mA (Note 2), single-ended clock mode CONDITIONS MIN 3.4 4 IFS = 20mA (Note 2), differential clock mode 3.4 Single-ended clock mode (DCE = 1) (Note 2) 11.1 Clock Supply Current ICVDD Differential clock mode (DCE = 0) (Note 2) 16.7 Total Standby Current ISTANDBY IAVDD + IDVDD + ICVDD 3.1 ISHDN IAVDD + IDVDD + ICVDD 1 Total Shutdown Current Single-ended clock mode (DCE = 1) Total Power Dissipation PTOT Differential clock mode (DCE = 0) IFS = 20mA (Note 2) 173 IFS = 2mA (Note 2) 58 IFS = 20mA (Note 2) 190 IFS = 2mA (Note 2) 75 Standby 9.3 Shutdown 13.5 3.7 UNITS mA mA mA A 191 mW 11.1 0.003 TIMING CHARACTERISTICS (Figures 5 and 6) Propagation Delay 1 DAC Data to CLK Rise/Fall Setup Time tDCS DAC Data to CLK Rise/Fall Hold Time tDCH Single-ended clock mode (DCE = 1) (Note 4) 1.2 Differential clock mode (DCE = 0) (Note 4) 2.7 Single-ended clock mode (DCE = 1) (Note 4) 0.8 Differential clock mode (DCE = 0) (Note 4) -0.5 Clock cycles ns ns Control Word to CW Rise Setup Time tCS 2.5 ns Control Word to CW Rise Hold Time tCW 2.5 ns CW High Time tCWH 5 ns CW Low Time tCWL 5 ns _______________________________________________________________________________________ 5 MAX5853 ELECTRICAL CHARACTERISTICS (continued) MAX5853 Dual, 10-Bit, 80Msps, Current-Output DAC ELECTRICAL CHARACTERISTICS (continued) (AVDD = DVDD = CVDD = 3V, AGND = DGND = CGND = 0, fDAC = 80Msps, differential clock, external reference, VREF = 1.2V, IFS = 20mA, differential output, output amplitude = 0dBFS, TA = TMIN to TMAX, unless otherwise noted. TA +25C, guaranteed by production test. TA < +25C guaranteed by design and characterization. Typical values are at TA = +25C.) PARAMETER SYMBOL DACEN = 1 to VOUT Stable Time (Coming Out of Standby) CONDITIONS MIN TYP MAX UNITS tSTB 3 s PD = 0 to VOUT Stable Time (Coming Out of Power-Down) tSHDN 500 s Maximum Clock Frequency at CLKXP/CLKXN Input fCLK Clock High Time tCXH CLKXP or CLKXN input 3 ns Clock Low Time tCXL CLKXP or CLKXN input 3 ns CLKXP Rise to CLK Output Rise Delay tCDH DCE = 0 2.7 ns CLKXP Fall to CLK Output Fall Delay tCDL DCE = 0 2.7 ns Note 1: Note 2: Note 3: Note 4: 80 MHz Including the internal reference voltage tolerance and reference amplifier offset. fDAC = 80Msps, fOUT = 10MHz. Measured single ended with 50 load and complementary output connected to ground. Guaranteed by design, not production tested. 0.5mA TO OUTPUT PIN 1.6V 5pF 0.5mA Figure 1. Load Test Circuit for CLK Outputs 6 _______________________________________________________________________________________ Dual, 10-Bit, 80Msps, Current-Output DAC -6dBFS 90 85 75 70 65 70 65 -12dBFS 60 55 SFDR (dBc) 75 70 65 60 55 -12dBFS 50 45 40 35 30 0 5 10 15 20 25 30 35 40 0dBFS -6dBFS 80 75 SFDR (dBc) -12dBFS 60 55 50 45 40 35 30 0 2 4 6 8 10 12 14 16 18 20 22 3 1 5 7 9 11 13 fOUT (MHz) fOUT (MHz) SPURIOUS-FREE DYNAMIC RANGE vs. OUTPUT FREQUENCY (fCLK = 65MHz) SPURIOUS-FREE DYNAMIC RANGE vs. OUTPUT FREQUENCY (fCLK = 80MHz) SPURIOUS-FREE DYNAMIC RANGE vs. OUTPUT FREQUENCY (fCLK = 80MHz) 0dBFS 80 75 SFDR (dBc) 70 -12dBFS 45 40 35 30 5 10 15 20 25 30 IOUT = 10mA AVDD = DVDD = CVDD = 2.7V 85 AVDD = DVDD = CVDD = 3V IOUT = 5mA 75 AVDD = DVDD = CVDD = 3.6V 70 AVDD = DVDD = CVDD = 3V 65 60 55 50 0 35 90 80 70 65 60 55 50 45 40 35 30 5 10 15 20 25 30 40 35 0 5 10 fOUT (MHz) fOUT (MHz) 82 0 -20 AMPLITUDE (dB) 79 78 fOUT1 = 8.2519MHz fOUT2 = 8.7030MHz -10 81 80 -30 25 30 35 40 fOUT2 fOUT1 -40 -50 -60 -70 77 20 TWO-TONE INTERMODULATION DISTORTION (fCLK = 80MHz, 8MHz WINDOW) MAX5853 toc07 83 15 fOUT (MHz) SPURIOUS-FREE DYNAMIC RANGE vs. TEMPERATURE (fCLK = 80MHz, fOUT = 10MHz, AOUT = 0dBFS) SFDR (dBc) 0 IOUT = 20mA MAX5853 toc08 65 60 55 50 90 85 80 75 SFDR (dBc) -6dBFS MAX5853 toc04 90 85 MAX5853 toc06 fOUT (MHz) MAX5853 toc05 SFDR (dBc) -6dBFS 80 50 45 40 35 30 SFDR (dBc) 0dBFS SPURIOUS-FREE DYNAMIC RANGE vs. OUTPUT FREQUENCY (fCLK = 25MHz) MAX5853 toc02 0dBFS 80 90 85 MAX5853 toc01 90 85 SPURIOUS-FREE DYNAMIC RANGE vs. OUTPUT FREQUENCY (fCLK = 44MHz) MAX5853 toc03 SPURIOUS-FREE DYNAMIC RANGE vs. OUTPUT FREQUENCY (fCLK = 80MHz) 2fOUT2 - fOUT1 2fOUT1 - fOUT2 -80 76 -90 75 -100 -40 -15 10 35 TEMPERATURE (C) 60 85 3.5 4.5 5.5 6.5 7.5 8.5 9.5 10.5 11.5 fOUT (MHz) _______________________________________________________________________________________ 7 MAX5853 Typical Operating Characteristics (AVDD = DVDD = CVDD = 3V, AGND = DGND = CGND = 0, external reference, IFS = 20mA, differential output, differential clock (unless otherwise noted), TA = +25C.) Typical Operating Characteristics (continued) (AVDD = DVDD = CVDD = 3V, AGND = DGND = CGND = 0, external reference, IFS = 20mA, differential output, differential clock (unless otherwise noted), TA = +25C.) fT5 -40 fT3 fT6 -50 fT2 fT7 fT1 fT8 -60 -80 -30 -40 -50 -60 -30 -40 -50 -60 -70 -70 -80 -80 -90 -90 -90 -100 -100 100 6.5 9.5 12.5 15.5 18.5 21.5 5 7 fOUT (MHz) 9 11 0.9 1.3 fOUT (MHz) SINGLE-TONE FFT PLOT (fCLK = 80MHz, NYQUIST WINDOW) fOUT = 10MHz AOUT = 0dBFS -20 SINGLE-TONE SFDR (fCLK = 65MHz, 2.5MHz WINDOW) 0 MAX5853 toc13 0 -10 -30 -40 -50 -60 -20 -30 -40 -50 -60 -70 -70 -80 -80 -90 -90 -100 -100 0.5 3.95MHz/div OUTPUT TONE FREQUENCY (MHz) 40 fOUT = 4.9901MHz AOUT = -1dBFS -10 AMPLITUDE (dB) AMPLITUDE (dB) 0.5 0.1 15 13 fOUT (MHz) fT5 = 14.825MHz fT6 = 15.675MHz fT7 = 16.475MHz fT8 = 17.375MHz fT1 = 10.825MHz fT2 = 11.475MHz fT3 = 12.425MHz fT4 = 13.175MHz 8 -20 MAX5853 toc12 -70 -20 fOUT = 1.0132MHz AOUT = -1dBFS -10 AMPLITUDE (dB) fT4 -30 AMPLITUDE (dB) -20 fOUT = 10.0572MHz AOUT = -1dBFS -10 0 MAX5853 toc10 0 MAX5853 toc09 0 -10 SINGLE-TONE SFDR (fCLK = 25MHz, 2MHz WINDOW) SINGLE-TONE SFDR (fCLK = 80MHz, 10MHz WINDOW) MAX5853 toc11 8-TONE SFDR PLOT (fCLK = 80MHz, 15MHz WINDOW) AMPLITUDE (dB) MAX5853 Dual, 10-Bit, 80Msps, Current-Output DAC 3.8 4.3 4.8 5.3 5.8 fOUT (MHz) _______________________________________________________________________________________ 6.3 1.7 2.1 Dual, 10-Bit, 80Msps, Current-Output DAC DIFFERENTIAL NONLINEARITY vs. DIGITAL INPUT CODE 0.4 0.3 0.1 0.1 0 -0.1 -0.2 -0.2 -0.3 -0.3 -0.4 -0.4 -0.5 150 300 450 600 750 900 1050 150 300 450 600 750 900 20 25 30 35 40 45 50 55 60 65 70 75 80 POWER DISSIPATION vs. SUPPLY VOLTAGES (fCLK = 80MHz, fOUT = 10MHz) REFERENCE VOLTAGE vs. SUPPLY VOLTAGES (fCLK = 80MHz, fOUT = 10MHz) DIFFERENTIAL CLOCK DRIVE 210 200 190 SINGLE-ENDED CLOCK DRIVE 180 170 REFERENCE VOLTAGE vs. TEMPERATURE MAX5853 toc18 1.25 1.22730 1.24 REFERENCE VOLTAGE (V) REFERENCE VOLTAGE (V) 220 fCLK (MHz) 1.22750 MAX5853 toc17 230 1.22710 1.22690 1.22670 160 160 1050 DIGITAL INPUT CODE 240 SINGLE-ENDED CLOCK DRIVE 140 0 DIGITAL INPUT CODE 250 170 150 -0.5 0 1.23 1.22 1.21 1.20 150 1.22650 2.70 2.85 3.00 3.15 3.30 3.45 1.19 2.70 3.60 2.85 3.00 3.15 3.30 3.45 3.60 -15 -40 SUPPLY VOLTAGES (V) SUPPLY VOLTAGES (V) MAX5853 toc21 MAX5853 toc20 35 60 85 SPURIOUS-FREE DYNAMIC RANGE vs. OUTPUT FREQUENCY (fCLK = 80MHz) DYNAMIC RESPONSE FALL TIME DYNAMIC RESPONSE RISE TIME 10 TEMPERATURE (C) 90 85 80 0dBFS -6dBFS MAX5853 toc22 140 100mV/div 75 100mV/div SFDR (dBc) POWER DISSIPATION (mW) 0 -0.1 DIFFERENTIAL CLOCK DRIVE 180 MAX5853 toc19 0.2 DNL (LSB) 0.2 190 POWER DISSIPATION (mW) 0.3 200 MAX5853 toc15 0.4 INL (LSB) 0.5 MAX5853 toc14 0.5 POWER DISSIPATION vs. CLOCK FREQUENCY (fOUT = 10MHz, AOUT = 0dBFS) MAX5853 toc16 INTEGRAL NONLINEARITY vs. DIGITAL INPUT CODE 70 65 60 55 50 -12dBFS 45 40 35 30 SINGLE-ENDED CLOCK DRIVE 35 40 _______________________________________________________________________________________ 9 10ns/div 10ns/div 0 5 10 15 20 25 30 fOUT (MHz) MAX5853 Typical Operating Characteristics (continued) (AVDD = DVDD = CVDD = 3V, AGND = DGND = CGND = 0, external reference, IFS = 20mA, differential output, differential clock (unless otherwise noted), TA = +25C.) Dual, 10-Bit, 80Msps, Current-Output DAC MAX5853 Pin Description PIN 1 2 10 NAME DA9/PD FUNCTION Channel A Input Data Bit 9 (MSB)/Power-Down DA8/DACEN Channel A Input Data Bit 8/DAC Enable Control 3 DA7/IDE Channel A Input Data Bit 7/Interleaved Data Enable 4 DA6/REN Channel A Input Data Bit 6/Reference Enable. Setting REN = 0 enables the internal reference. Setting REN = 1 disables the internal reference. 5 DA5/G3 Channel A Input Data Bit 5/Channel A Gain Adjustment Bit 3 6 DA4/G2 Channel A Input Data Bit 4/Channel A Gain Adjustment Bit 2 7 DA3/G1 Channel A Input Data Bit 3/Channel A Gain Adjustment Bit 1 8 DA2/G0 Channel A Input Data Bit 2/Channel A Gain Adjustment Bit 0 9 DA1 Channel A Input Data Bit 1 10 DA0 Channel A Input Data Bit 0 (LSB) 11 DB9 Channel B Input Data Bit 9 (MSB) 12 DB8 Channel B Input Data Bit 8 13 DB7 Channel B Input Data Bit 7 14 DB6 Channel B Input Data Bit 6 15 DB5 Channel B Input Data Bit 5 16 DVDD 17 DGND Digital Power Input. See the Power Supplies, Bypassing, Decoupling, and Layout section for more details. 18 DB4 Channel B Input Data Bit 4 19 DB3 Channel B Input Data Bit 3 20 DB2 Channel B Input Data Bit 2 21 DB1 Channel B Input Data Bit 1 22 DB0 Channel B Input Data Bit 0 (LSB) 23 CW Active-Low Control Word Write Pulse. The control word is latched on the rising edge of CW. 24 DCE Active-Low Differential Clock Enable Input. Drive DCE low to enable the differential clock inputs CLKXP and CLKXN. Drive DCE high to disable the differential clock inputs and enable the singleended CLK input. 25 CLKXP Positive Differential Clock Input. With DCE = 0, CLKXP and CLKXN are enabled. With DCE = 1, CLKXP and CLKXN are disabled. Connect CLKXP to CGND when the differential clock is disabled. 26 CLKXN Negative Differential Clock Input. With DCE = 0, CLKXP and CLKXN are enabled. With DCE = 1, CLKXP and CLKXN are disabled. Connect CLKXN to CVDD when the differential clock is disabled. 27, 30 CVDD Digital Ground Clock Power Input. See the Power Supplies, Bypassing, Decoupling, and Layout section for more Single-Ended Clock Input/Output. With the differential clock disabled (DCE = 1), CLK becomes a single-ended conversion clock input. With the differential clock enabled (DCE = 0), CLK is a singleended output that mirrors the differential clock inputs CLKXP and CLKXN. See the Clock Modes section for more information on CLK. 28 CLK 29 CGND Clock Ground 31 REFO Reference Input/Output. REFO serves as a reference input when the internal reference is disabled. If the internal 1.24V reference is enabled, REFO serves as an output for the internal reference. When the internal reference is enabled, bypass REFO to AGND with a 0.1F capacitor ______________________________________________________________________________________ Dual, 10-Bit, 80Msps, Current-Output DAC PIN NAME FUNCTION 32 REFR Full-Scale Current Adjustment. To set the output full-scale current, connect an external resistor RSET between REFR and AGND. The output full-scale current is equal to 32 x VREFO/RSET. 33, 39 AVDD Analog Power Input. See the Power Supplies, Bypassing, Decoupling, and Layout section for more details. 34 OUTNB Channel B Negative Analog Current Output 35 OUTPB Channel B Positive Analog Current Output 36, 40 AGND Analog Ground 37 OUTNA Channel A Negative Analog Current Output 38 OUTPA -- EP Channel A Positive Analog Current Output Exposed Paddle. Connect EP to the common point of all ground planes. Detailed Description DVDD DGND ANALOG POWER MANAGEMENT DIGITAL POWER MANAGEMENT AVDD AGND CW MAX5853 DACA INPUT REGISTER CONTROL WORD DA0 DA1 DA2/G0 DA3/G1 DA4/G2 DA5/G3 DA6/REN DA7/IDE DA8/DACEN DA9/PD DCE CLKXP CLKXN CLK CVDD CGND G0 G1 G2 G3 CHANNEL A GAIN CONTROL INPUT DATA INTERLEAVER The MAX5853 features three modes of operation: normal, standby, and power-down (Table 2). These modes allow efficient power management. In power-down, the MAX5853 consumes only 1A of supply current. Wakeup time from standby mode to normal DAC operation is 3s. IDE OPERATING MODE CONTROLLER DACB INPUT REGISTER DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8 DB9 OUTPA OUTNA 10-BIT DACA DACEN PD Programming the DAC OUTPB OUTNB 10-BIT DACB REFO CLOCK DISTRIBUTION CLOCK POWER MANAGEMENT 1.24V REFERENCE AND CONTROL AMPLIFIER The MAX5853 dual, high-speed, 10-bit, current-output DAC provides superior performance in communication systems requiring low-distortion analog-signal reconstruction. The MAX5853 combines two DACs and an onchip 1.24V reference (Figure 2). The current outputs of the DACs can be configured for differential or singleended operation. The full-scale output current range is adjustable from 2mA to 20mA to optimize power dissipation and gain control. The MAX5853 accepts an input data and a DAC conversion rate of 80MHz. The inputs are latched on the rising edge of the clock whereas the output latches on the following rising edge. REFR RSET REN AGND An 8-bit control word routed through channel A's data port programs the gain matching, reference, and the operational mode of the MAX5853. The control word is latched on the rising edge of CW. CW is independent of the DAC clock. The DAC clock can always remain running when the control word is written to the DAC. Table 1 and Table 2 represent the control word format and function. The gain on channel A can be adjusted to achieve gain matching between two channels in a user's system. The gain on channel A can be adjusted from -0.4dB to 0.35dB in steps of 0.05dB by using bits G3 to G0 (see Table 3). Figure 2. Simplified Diagram ______________________________________________________________________________________ 11 MAX5853 Pin Description (continued) MAX5853 Dual, 10-Bit, 80Msps, Current-Output DAC Table 1. Control Word Format and Function MSB LSB DACEN PD REN IDE G3 CONTROL WORD PD G1 G0 X X FUNCTION Power-Down. The part enters power-down mode if PD = 1. DACEN DAC Enable. When DACEN = 0 and PD = 0, the part enters standby mode. IDE Interleaved Data Mode. IDE = 1 enables the interleaved data mode. In this mode, digital data for both channels is applied through channel A in a multiplexed fashion. Channel B data is written on the falling edge of the clock signal and channel A data is written on the rising edge of the clock signal. REN Reference Enable Bit. REN = 0 activates the internal reference. REN = 1 disables the internal reference and requires the user to apply an external reference between 0.1V to 1.32V. G3 Bit 3 (MSB) of Gain Adjust Word G2 Bit 2 of Gain Adjust Word G1 Bit 1 of Gain Adjust Word G0 Bit 0 (LSB) of Gain Adjust Word Device Power-Up and States of Operation Table 2. Configuration Modes PD DACEN IDE REN Normal operation; noninterleaved inputs; internal reference active 0 1 0 0 Normal operation; noninterleaved inputs; internal reference disabled 0 1 0 1 Normal operation; interleaved inputs; internal reference disabled 0 1 1 1 Standby 0 0 X X Power-down 1 X X X Power-up 0 1 X X MODE X = Don't care. Table 3. Gain Difference Setting 12 G2 GAIN ADJUSTMENT ON CHANNEL A (dB) G3 G2 G1 G0 +0.4 0 0 0 0 0 1 0 0 0 -0.35 1 1 1 1 At power-up, the MAX5853's default configuration is internal reference, noninterleaved input mode with a gain of 0dB and a fully operational converter. In shutdown, the MAX5853 consumes only 1A of supply current, and in standby the current consumption is 3.1mA. Wake-up time from standby mode to normal operation is 3s. Clock Modes The MAX5853 allows both single-ended CMOS and differential clock mode operation, and supports update rates of up to 80Msps. These modes are selected through an active-low control line called DCE. In singleended clock mode (DCE = 1), the CLK pin functions as an input, which accepts a user-provided single-ended clock signal. Data is written to the converter on the rising edge of the clock. The DAC outputs (previous data) are updated simultaneously on the same edge. If the DCE pin is pulled low, the MAX5853 operates in differential clock mode. In this mode, the clock signal has to be applied to the differential clock input pins CLKXP/CLKXN. The differential input accepts an input range of 0.5VP-P and a common-mode range of 1V to (CVDD - 0.5V), making the part ideal for low-input amplitude clock drives. CLKXP/CLKXN also help to minimize the jitter, and allow the user to connect a crystal oscillator directly to the MAX5853. The CLK pin now becomes an output, and provides a single-ended replica of the differential clock signal, which may be used to synchronize the input data. Data is written to the device on the rising edge of the CLK signal. ______________________________________________________________________________________ Dual, 10-Bit, 80Msps, Current-Output DAC 10F MAX4040 1.24V BANDGAP REFERENCE AGND 1.24V BANDGAP REFERENCE AVDD MAX6520 CCOMP* REFR CURRENTSOURCE ARRAY IREF IFS AGND IREF = EXTERNAL 1.2V REFERENCE REFR MAX5853 Figure 3. Setting IFS with the Internal 1.24V Reference and the Control Amplifier CURRENTSOURCE ARRAY IREF IFS AGND RSET AGND *COMPENSATION CAPACITOR (CCOMP 100nF). REN = 1 REFO RSET RSET 0.1F REN = 0 REFO VREF MAX5853 AVDD OPTIONAL EXTERNAL BUFFER FOR HEAVIER LOADS MAX5853 AGND Figure 4. MAX5853 with External Reference Internal Reference and Control Amplifier External Reference The MAX5853 provides an integrated 50ppm/C, 1.24V, low-noise bandgap reference that can be disabled and overridden with an external reference voltage. REFO serves either as an external reference input or an integrated reference output. If REN = 0, the internal reference is selected and REFO provides a 1.24V (50A) output. Buffer REFO with an external amplifier, when driving a heavy load. The MAX5853 also employs a control amplifier designed to simultaneously regulate the full-scale output current (I FS ) for both outputs of the devices. Calculate the output current as: IFS = 32 IREF where I REF is the reference output current (I REF = VREFO / RSET) and IFS is the full-scale output current. RSET is the reference resistor that determines the amplifier output current of the MAX5853 (Figure 3). This current is mirrored into the current-source array where IFS is equally distributed between matched current segments and summed to valid output current readings for the DACs. To disable the internal reference of the MAX5853, set REN = 1. Apply a temperature-stable, external reference to drive the REFO pin and set the full-scale output (Figure 4). For improved accuracy and drift performance, choose a fixed output voltage reference such as the 1.2V, 25ppm/C MAX6520 bandgap reference. Detailed Timing The MAX5853 accepts an input data and DAC conversion rate of up to 80Msps. The input latches on the rising edge of the clock, whereas the output latches on the following rising edge. Figure 5 depicts the write cycle of the two DACs in noninterleaved mode. The MAX5853 can also operate in an interleaved data mode. Programming the IDE bit with a high level activates this mode (Tables 1 and 2). In interleaved mode, data for both DAC channels is written through input port A. Channel B data is written on the falling edge of the clock signal and then channel A data is written on the following rising edge of the clock signal. Both DAC outputs (channel A and B) are updated simultaneously on the next following rising edge of the clock. The interleaved data mode is attractive for applications where lower data rates are acceptable and interfacing on a single 10-bit bus is desired (Figure 6). ______________________________________________________________________________________ 13 MAX5853 Dual, 10-Bit, 80Msps, Current-Output DAC tCXH tCXL CLKXN CLKXP tCDL tCDH CLK OUTPUT tCWL CW tDCS DA0-DA9 DACA - 1 tCS tDCH DACA + 1 DACA tCW CONTROL WORD DACA + 2 DACA + 3 OUTNA DACA - 1 DACA DACA + 1 XXXX DACA + 2 (CONTROL WORD DATA) DACA + 3 OUTPA tDCS DB0-DB9 DACB - 1 tDCH DACB DACB + 1 DACB + 2 XXXX DACB + 3 OUTNB DACB - 1 DACB DACB + 1 DACB + 2 XXXX DACB + 3 OUTPB Figure 5. Timing Diagram for Noninterleaved Data Mode (IDE = 0) tCXL tCXH CLKXN CLKXP tCDH tCDL CLK OUTPUT tCWL CW tDCS DA0-DA9 DACA tDCH DACB + 1 tDCS tDCH DACA + 1 tCS tCW CONTROL WORD DACB + 2 DACA + 2 OUTNA DACA - 1 DACA DACA + 1 DACB - 1 DACB DACB + 1 OUTPA OUTNB OUTPB Figure 6. Timing Diagram for Interleaved Data Mode (IDE = 1) 14 ______________________________________________________________________________________ Dual, 10-Bit, 80Msps, Current-Output DAC AVDD DVDD CVDD 50 OUTPA DA0-DA9 MAX5853 AVDD DVDD CVDD VOUTA, SINGLE ENDED 50 DA0-DA9 1/2 OUTPA 1/2 100 MAX5853 10 MAX5853 10 OUTNA OUTNA 50 50 OUTPB DB0-DB9 50 50 VOUTB, SINGLE ENDED DB0-DB9 1/2 100 10 MAX5853 10 OUTPB 1/2 MAX5853 OUTNB OUTNB 50 50 AGND DGND CGND Figure 7. Application with Output Transformer Performing Differential-to-Single-Ended Conversion Applications Information Differential-to-Single-Ended Conversion The MAX5853 exhibits excellent dynamic performance to synthesize a wide variety of modulation schemes, including high-order QAM modulation with OFDM. Figure 7 shows a typical application circuit with output transformers performing the required differential-tosingle-ended signal conversion. In this configuration, the MAX5853 operates in differential mode, which reduces even-order harmonics, and increases the available output power. Differential DC-Coupled Configuration Figure 8 shows the MAX5853 output operating in differential, DC-coupled mode. This configuration can be used in communication systems employing analog quadrature upconverters and requiring a baseband sampling, dual-channel, high-speed DAC for I/Q syn- AGND DGND CGND Figure 8. Application with DC-Coupled Differential Outputs thesis. In these applications, information bandwidth can extend from 10MHz down to several hundred kilohertz. DC-coupling is desirable to eliminate long discharge time constants that are problematic with large, expensive coupling capacitors. Analog quadrature upconverters have a DC common-mode input requirement of typically 0.7V to 1.0V. The MAX5853 differential I/Q outputs can maintain the desired full-scale level at the required 0.7V to 1.0V DC common-mode level when powered from a single 2.85V (5%) supply. The MAX5853 meets this low-power requirement with minimal reduction in dynamic range while eliminating the need for level-shifting resistor networks. Power Supplies, Bypassing, Decoupling, and Layout Grounding and power-supply decoupling strongly influence the MAX5853 performance. Unwanted digital crosstalk can couple through the input, reference, ______________________________________________________________________________________ 15 MAX5853 Dual, 10-Bit, 80Msps, Current-Output DAC power-supply, and ground connections, which can affect dynamic specifications, like signal-to-noise ratio or spurious-free dynamic range. In addition, electromagnetic interference (EMI) can either couple into or be generated by the MAX5853. Observe the grounding and power-supply decoupling guidelines for highspeed, high-frequency applications. Follow the power supply and filter configuration to realize optimum dynamic performance. Use of a multilayer printed circuit (PC) board with separate ground and power-supply planes is recommended. Run high-speed signals on lines directly above the ground plane. The MAX5853 has separate analog and digital ground buses (AGND, CGND, and DGND, respectively). Provide separate analog, digital, and clock ground sections on the PC board with only one point connecting the three planes. The ground connection points should be located underneath the device and connected to the exposed paddle. Run digital signals above the digital ground plane and analog/clock signals above the analog/clock ground plane. Digital signals should be kept away from sensitive analog, clock, and reference inputs. Keep digital signal paths short and metal trace lengths matched to avoid propagation delay and data skew mismatch. The MAX5853 includes three separate power-supply inputs: analog (AV DD ), digital (DV DD ), and clock (CVDD). Use a single linear regulator power source to branch out to three separate power-supply lines (AVDD, DV DD , CV DD ) and returns (AGND, DGND, CGND). Filter each power-supply line to the respective return line using LC filters comprising ferrite beads and 10F capacitors. Filter each supply input locally with 0.1F ceramic capacitors to the respective return lines. Note: To maintain the dynamic performance of the Electrical Characteristics, ensure the voltage difference between DV DD , AV DD , and CV DD does not exceed 150mV. Thermal Characteristics and Packaging Thermal Resistance 40-lead thin QFN-EP: JA = 38C/W The MAX5853 is packaged in a 40-pin thin QFN-EP package, providing greater design flexibility, increased thermal efficiency, and optimized AC performance of the DAC. The EP enables the implementation of grounding techniques, which are necessary to ensure highest performance operation. In this package, the data converter die is attached to an EP leadframe with the back of this frame exposed at the package bottom surface, facing the PC board side of the package. This allows a solid attachment of the package to the PC board with standard infrared (IR) flow soldering techniques. A specially created land pattern on the PC board, matching the size of the EP (4.1mm 4.1mm), ensures the proper attachment and grounding of the DAC. Designing vias* into the land area and implementing large ground planes in the PC board design allows for highest performance operation of the DAC. Use an array of 3 3 vias (0.3mm diameter per via hole and 1.2mm pitch between via holes) for this 40pin thin QFN-EP package (package code: T4066-1). Dynamic Performance Parameter Definitions Total Harmonic Distortion (THD) THD is the ratio of the RMS sum of all essential harmonics (within a Nyquist window) of the input signal to the fundamental itself. This can be expressed as: 2 2 2 2 V2 + V3 + V4 ... + ...VN THD = 20 x log V1 where V1 is the fundamental amplitude, and V2 through VN are the amplitudes of the 2nd through Nth order harmonics. The MAX5853 uses the first seven harmonics for this calculation. Spurious-Free Dynamic Range (SFDR) SFDR is the ratio of RMS amplitude of the carrier frequency (maximum signal component) to the RMS value of their next-largest spectral component. SFDR is usually measured in dBc with respect to the carrier frequency amplitude or in dBFS with respect to the DAC's full-scale range. Depending on its test condition, SFDR is observed within a predefined window or to Nyquist. Multitone Power Ratio (MTPR) A series of equally spaced tones are applied to the DAC with one tone removed from the center of the range. MTPR is defined as the worst-case distortion (usually a 3rd-order harmonic product of the fundamental frequencies), which appears as the largest spur at the frequency of the missing tone in the sequence. This test can be performed with any number of input tones; however, four and eight tones are among the most common test conditions for CDMA- and GSM/EDGE-type applications. *Vias connect the land pattern to internal or external copper planes. 16 ______________________________________________________________________________________ Dual, 10-Bit, 80Msps, Current-Output DAC Static Performance Parameter Definitions Integral Nonlinearity (INL) Integral nonlinearity (INL) is the deviation of the values on an actual transfer function from a line drawn between the end points of the transfer function, once offset and gain errors have been nullified. For a DAC, the deviations are measured at every individual step. Differential Nonlinearity (DNL) Differential nonlinearity (DNL) is the difference between an actual step height and the ideal value of 1 LSB. A DNL error specification no more negative than -1 LSB guarantees monotonic transfer function. Offset Error Offset error is the current flowing from positive DAC output when the digital input code is set to zero. Offset error is expressed in LSBs. Gain Error A gain error is the difference between the ideal and the actual full-scale output current on the transfer curve, after nullifying the offset error. This error alters the slope of the transfer function and corresponds to the same percentage error in each step. The ideal current is defined by reference voltage at VREFO / IREF x 32. Settling Time The settling time is the amount of time required from the start of a transition until the DAC output settles to its new output value to within the converter's specified accuracy. Glitch Impulse A glitch is generated when a DAC switches between two codes. The largest glitch is usually generated around the midscale transition, when the input pattern transitions from 011...111 to 100...000. This occurs due to timing variations between the bits. The glitch impulse is found by integrating the voltage of the glitch at the midscale transition over time. The glitch impulse is usually specified in pV-s. Table 4. Part Selection Table SPEED (Msps) RESOLUTION MAX5851 PART 80 8-bit, dual MAX5852 165 8-bit, dual MAX5853 80 10-bit, dual MAX5854 165 10-bit, dual Chip Information TRANSISTOR COUNT: 9,035 PROCESS: CMOS ______________________________________________________________________________________ 17 MAX5853 Intermodulation Distortion (IMD) The two-tone IMD is the ratio expressed in dBc of either output tone to the worst 3rd-order (or higher) IMD products. Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) QFN THIN 6x6x0.8.EPS MAX5853 Dual, 10-Bit, 80Msps, Current-Output DAC D2 D CL D/2 b D2/2 k E/2 E2/2 E (NE-1) X e CL E2 k e L (ND-1) X e CL CL L L e A1 A2 e A PACKAGE OUTLINE 36,40L THIN QFN, 6x6x0.8 mm 21-0141 D 1 2 NOTES: 1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994. 2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES. 3. N IS THE TOTAL NUMBER OF TERMINALS. 4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE. 5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.25 mm AND 0.30 mm FROM TERMINAL TIP. 6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY. 7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION. 8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS. 9. DRAWING CONFORMS TO JEDEC MO220. 10. WARPAGE SHALL NOT EXCEED 0.10 mm. PACKAGE OUTLINE 36, 40L THIN QFN, 6x6x0.8 mm 21-0141 D 2 2 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 18 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2004 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.