MCC TM Micro Commercial Components RL101 THRU RL107 omponents 20736 Marilla Street Chatsworth !"# $ % !"# Features * * * * * * * Halogen free available upon request by adding suffix "-HF" Low Current Leakage Metalurgically Bonded Construction Low Cost Epoxy meets UL 94 V-0 flammability rating Moisture Sensitivity Level 1 Lead Free Finish/Rohs Compliant (Note1) ("P"Suffix designates Compliant. See ordering information) 1 Amp Rectifier 50 - 1000 Volts A-405 Maximum Ratings * * * Operating Temperature: -55C to +150C Storage Temperature: -55C to +150C Maximum Thermal Resistance; 50 C/W Junction To Lead MCC Catalog Number Device Marking RL101 RL102 RL103 RL104 RL105 RL106 RL107 RL101 RL102 RL103 RL104 RL105 RL106 RL107 Maximum Recurrent Peak Reverse Voltage 50V 100V 200V 400V 600V 800V 1000V Maximum RMS Voltage 35V 70V 140V 280V 420V 560V 700V Maximum DC Blocking Voltage D A 50V 100V 200V 400V 600V 800V 1000V Cathode Mark B D C Electrical Characteristics @ 25C Unless Otherwise Specified Average Forward IF(AV) 1.0A TA = 75C Current Peak Forward Surge IFSM 30A 8.3ms, half sine Current Maximum VF 1.1V IFM = 1.0A; Instantaneous Forward Voltage TJ = 25C* Maximum DC Reverse Current At IR 5.0A TJ = 25C Rated DC Blocking 50A TJ = 125C Voltage Typical Junction CJ 15pF Measured at Capacitance 1.0MHz, VR=4.0V *Pulse test: Pulse width 300 sec, Duty cycle 2% Note: DIMENSIONS DIM A B C D INCHES MIN .166 .080 --1.000 MAX .205 .107 .024 --- MM MIN 4.10 2.00 --25.40 MAX 5.20 2.70 .60 --- NOTE 1. High Temperature Solder Exemptions Applied, see EU Directive Annex 7. Revision: C www.mccsemi.com 1 of 5 2013/07/02 MCC RL101 thru RL107 Figure 1 Typical Forward Characteristics TM Micro Commercial Components 20 Figure 2 Forward Derating Curve 10 1.2 6 4 1.0 2 Amps .8 1 .6 .6 Amps .4 .4 .2 25C .2 .1 Single Phase, Half Wave 60Hz Resistive or Inductive Load .06 0 .04 0 50 75 100 125 150 175 C .02 .01 .4 .6 .8 1.0 1.2 Average Forward Rectified Current - Amperesversus Ambient Temperature - C 1.4 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 20 pF TJ=25C 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 400 1000 Junction Capacitance - pFversus Reverse Voltage - Volts Revision: C www.mccsemi.com 2 of 5 2013/07/02 MCC RL101 thru RL107 Figure 4 Typical Reverse Characteristics Micro Commercial Components Figure 5 Peak Forward Surge Current 100 60 60 40 50 20 40 10 30 6 Amps 4 T =100C A 20 10 2 0 Amps 1 1 2 4 6 .6 8 10 20 40 60 80 100 Cycles .4 Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles .2 .1 TA=25C .06 .04 .02 .01 20 40 60 80 100 120 140 Volts Instantaneous Reverse Leakage Current - MicroAmperesversus Percent Of Rated Peak Reverse Voltage - Volts Revision: C www.mccsemi.com 3 of 5 2013/07/02 TM MCC TM Micro Commercial Components RADIAL TAPING SPECIFICATIONS FOR RECTIFIERS A-405 Outline Only C B S F D G P H A E T N M J K PACKING METHODS P/N EXAMPLE: A=N:PANASERT ABC DIMENSIONS DIM A B C D E F G H J K M N P S T INCHES MIN MAX .709 .748 .460 .540 --.106 --.205 .610 .650 --.354 --.177 .177 .217 .124 .179 .146 .169 .677 .748 .343 .384 .021 .025 --.079 .016 .031 MM MIN 18.0 11.7 ----15.5 ----4.5 3.15 3.7 17.2 8.70 .54 --.4 MAX 20.0 13.7 2.7 5.2 16.5 9.0 4.5 5.5 4.55 4.3 19.0 9.75 .64 2.0 .8 NOTE B = 0: NON INSULATION COATING--LEAD FIRST OUT. 1: INSULATION COATING--LEAD FIRST OUT. 2: NON INSULATION COATING--BODY FIRST OUT. 3: INSULATION COATING--BODY FIRST OUT. C = 1: FOR CATHODE DOWN, IN BULK. 2: FOR CATHODE UP, IN BULK. 3: FOR CATHODE DOWN, IN REEL. 4: FOR CATHODE UP, IN REEL www.mccsemi.com Revision: C 4 of 5 2013/07/02 MCC TM Micro Commercial Components Ordering Information : Device Packing Part Number-TP Tape&Reel: 5Kpcs/Reel RL104-A-B-C-AP(See page 4 for A/B/C suffix details) Ammo Packing: 2Kpcs/Ammo Box Note : Adding "-HF" suffix for halogen free, eg. Part Number-TP-HF ***IMPORTANT NOTICE*** Micro Commercial Components Corp. reserves the right to make changes without further notice to any product herein to make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are represented on our website, harmless against all damages. ***LIFE SUPPORT*** MCC's products are not authorized for use as critical components in life support devices or systems without the express written approval of Micro Commercial Components Corporation. ***CUSTOMER AWARENESS*** Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages customers to purchase MCC parts either directly from MCC or from Authorized MCC Distributors who are listed by country on our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine parts, have full traceability, meet MCC's quality standards for handling and storage. MCC will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. MCC is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. www.mccsemi.com Revision: C 5 of 5 2013/07/02