3.3 - 51
3.3
Three Terminal, Fixed Voltage, 1.5 Amp
Precision Positive Regulators In Hermetic
JEDEC TO-3 Package
4 11 R0
HERMETIC TO-3 FIXED VOLTAGE REGULATORS
APPROVED TO DESC DRAWINGS
FEATURES
• Output Voltages: 5V, 12V, 15V
• Output Voltages Set Internally to ±1%
• Built-In Thermal Overload Protection
• Short Circuit Current Limiting
• Similar To Industry Standards 7805, 7812, 7815
• Hi-Rel Screening Available
DESCRIPTION
These three terminal positive regulators are supplied in a hermetically sealed metal
TO-3 package. All protective features are designed into the circuit, including thermal
shutdown, current limiting and safe-area control. With heat sinking, they can deliver
over 1.5 amps of output current. These units feature internally trimmed output
voltages ±1% of nominal voltage. These units are ideally suited for Military
applications where a hermetically sealed package is required.
PART NUMBER DESIGNATOR
Standard Military Drawing Number Omnirel Part Number
5962-8778201 YX OM1805NKM
5962-8777601 YX OM1812NKM
5962-8855301 YX OM1815NKM
OM1815NKMOM1805NKM
OM1812NKM
3.3 - 52
OM1805NKM - OM1815NKM
3.3
ELECTRICAL CHARACTERISTICS 5 Volt VIN = 10V, Io= 500mA, -55°C TA 125°C (unless otherwise specified)
Parameter Symbol Test Conditions Min. Max. Unit
Output Voltage VOUT TA= 25°C 4.92 5.08 V
VIN = 7.5V to 20V •4.85 5.15 V
IO = 5mA to 1.0A, P < 20 W
Line Regulation VRLINE VIN = 7.5V to 20V 5 mV
(Note 1) •12 mV
(Note 4) VIN = 8.0V to 12V 4 mV
•10 mV
Load Regulation VRLOAD IO = 5mA to 1.5 Amp 12 mV
(Note 1) IO = 5mA to 1.0Amp •25 mV
IO = 250mA to 750 mA 6 mV
•15 mV
Standby Current Drain ISCD 6mA
•6.5 mA
Standby Current Drain DISCD VIN = 7.5V to 20V •0.8 mA
Change With Line (Line)
Standby Current Drain DISCD IO= 5mA to 1000mA •0.5 mA
Change With Load (Load)
Dropout Voltage VDO TA= 25°C, DVOUT = 100mV, IO=1.0A 2.5 V
Peak Output Current IO (pk) TA= 25°C 1.5 3.3 A
Short Circuit Current IDS VIN = 35V 1.2 A
(Note 2) •2.8 A
Ripple Rejection DVIN f =120 Hz, DVIN = 10V 66 dB
DVOUT (Note 3) •60 dB
Output Noise Voltage NOTA= 25°C, f =10 Hz to 100KHz 40 µV/V
(Note 3) RMS
Long Term Stability DVOUT TA= 25°C, t = 1000 hrs. 75 mV
(Note 3) Dt
Notes:
1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used.
Changes in output voltage due to heating effects must be taken into account separately.
2. Short Circuit protection is only assured up to VIN = 35V.
3. If not tested, shall be guaranteed to the specified limits.
The • denotes the specifications which apply over the full operating temperature range.
4. Minimum load current for full line regulation = 5.0 mA.
ABSOLUTE MAXIMUM RATINGS @ 25°C
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +35 V
Operating Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55°C to + 150°C
Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65°C to + 150°C
Typical Power/Thermal Charateristics:
Rated Power @ 25° C TC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20W
TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3W
Thermal Resistance qJC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3°C/W
qJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29°C/W
a
3.3 - 53
OM1805NKM - OM1815NKM
3.3
ELECTRICAL CHARACTERISTICS 12 Volt VIN = 19V, Io= 500mA, -55°C TA 125°C (unless otherwise specified)
Parameter Symbol Test Conditions Min. Max. Unit
Output Voltage VOUT TA= 25°C 11.88 12.12 V
VIN = 14.5V to 27V •11.64 12.36 V
IO = 5mA to 1.0 A, P < 20W
Line Regulation VRLINE VIN = 14.5V to 27V 18 mV
(Note 1) •50 mV
(Note 4) VIN = 16V to 22V 9 mV
•30 mV
Load Regulation VRLOAD IO = 5mA to 1.5 Amp 32 mV
(Note 1) IO = 5mA to 1.0 Amp •60 mV
IO = 250mA to 750 mA 20 mV
•40 mV
Standby Current Drain ISCD 6.0 mA
•6.5 mA
Standby Current Drain DISCD VIN = 15V to 30V •0.8 mA
Change With Line (Line)
Standby Current Drain DISCD IO= 5mA to 1000mA •0.5 mA
Change With Load (Load)
Dropout Voltage VDO DVOUT = 100mV, IO=1.0A •2.5 V
Peak Output Current IO (pk) TA= 25°C 1.5 3.3 A
Short Circuit Current IDS VIN = 35V 1.2 A
(Note 2) •2.8 A
Ripple Rejection DVIN f =120 Hz, DVIN = 10V 61 dB
DVOUT (Note 3) •54 dB
Output Noise Voltage NOTA= 25°C, f =10 Hz to 100KHz 40 µV/V
(Note 3) RMS
Long Term Stability DVOUT TA= 25°C, t = 1000 hrs. 120 mV
(Note 3) Dt
Notes:
1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used.
Changes in output voltage due to heating effects must be taken into account separately.
2. Short Circuit protection is only assured up to VIN = 35V.
3. If not tested, shall be guaranteed to the specified limits.
The • denotes the specifications which apply over the full operating temperature range.
4. Minimum load current for full line regulation = 5.0 mA.
1.197
1.177
0.675
0.655
0.188 R.
MAX.
0.440
0.420
0.161
0.151 0.525 R.
MAX.
0.225
0.205
SEATING
PLANE
0.312
MIN.
0.450
0.250
0.043
0.038
2 PLCS.
0.135
MAX.
0.875
MAX.
1.53
REF.
MECHANICAL OUTLINE
Pin Connection
Pin 1: Input
Pin 2: Output
Case: Ground
1
2
OM1805NKM - OM1815NKM
3.3
205 Crawford Street, Leominster, MA 01453 USA (508) 534-5776 FAX (508) 537-4246
ELECTRICAL CHARACTERISTICS 15 Volt VIN = 23V, Io= 500mA, -55°C TA 125°C (unless otherwise specified)
Parameter Symbol Test Conditions Min. Max. Unit
Output Voltage VOUT TA= 25°C 14.8 15.2 V
VIN = 18.5V to 30V •14.6 15.4 V
IO = 5mA to 1.0 A, P < 20W
Line Regulation VRLINE VIN = 17.5V to 30V 20 mV
(Note 1) •50 mV
(Note 4) V IN = 20V to 26V 15 mV
•25 mV
Load Regulation VRLOAD IO = 5mA to 1.5 Amp 35 mV
(Note 1) IO = 5mA to 1.0 Amp •75 mV
IO = 250mA to 750 mA 21 mV
•45 mV
Standby Current Drain ISCD 6.0 mA
•6.5 mA
Standby Current Drain DISCD VIN = 18.5V to 30V •0.8 mA
Change With Line (Line)
Standby Current Drain DISCD IO= 5mA to 1000mA •0.5 mA
Change With Load (Load)
Dropout Voltage VDO TA= 25°C, DVOUT = 100mV, IO=1.0A 2.5 V
Peak Output Current IO (pk) TA= 25°C 1.5 3.3 A
Short Circuit Current IDS VIN = 35V 1.2 A
(Note 2) •2.8 A
Ripple Rejection DVIN f =120 Hz, DVIN = 10V 54 dB
DVOUT (Note 3) •52 dB
Output Noise Voltage NOTA= 25°C, f =10 Hz to 100KHz 40 µV/V
(Note 3) RMS
Long Term Stability DVOUT TA= 25°C, t = 1000 hrs. 150 mV
(Note 3) Dt
Notes:
1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used.
Changes in output voltage due to heating effects must be taken into account separately.
2. Short Circuit protection is only assured up to VIN = 35V.
3. If not tested, shall be guaranteed to the specified limits.
The • denotes the specifications which apply over the full operating temperature range.
4. Minimum load current for full line regulation = 5.0 mA.
3.5
3
2.5
2
1.5
1
0.5
00 5 10 15 20 25 30 35
PEAK OUTPUT
DVOUT = 100mV
Tj= -55°C
Tj= 25°C
Tj= 150°C
Input To Output Differential (V)
2.5
2
1.5
1
0.5
0-75-50 -25 0 25 50 75 100 125 150
DROPOUT VOLTAGE
DVOUT = 100MV
IOUT = 0A
IOUT = 500mA
IOUT = 1A
Junction Temperature (°C)
100
80
60
40
20
010 100 1k 10k 100k
RIPPLE REJECTION
VOUT = 5V
VIN - V = 8VDC +3.5Vrms
IOUT = 1A
Tj= 25°C
Frequency (Hz)
TYPICAL PERFORMANCE CHARACTERISTICS
Ripple Rejection (dB)
Output Current (A)
