IS41C16105C IS41LV16105C 1Mx16 16Mb DRAM WITH FAST PAGE MODE ADVANCED INFORMATION APRIL 2010 FEATURES DESCRIPTION * TTL compatible inputs and outputs; tristate I/O The ISSI IS41C16105C and IS41LV16105C are 1,048,576 x 16-bit high-performance CMOS Dynamic Random Access Memories. Fast Page Mode allows 1,024 random accesses within a single row with access cycle time as short as 20 ns per 16-bit word. The Byte Write control, of upper and lower byte, makes the IS41C16105C ideal for use in 16-, 32-bit wide data bus systems. * Refresh Interval: -- 1,024 cycles/16 ms * Refresh Mode: -- RAS-Only, CAS-before-RAS (CBR), and Hidden * JEDEC standard pinout * Single power supply: -- 5V 10% (IS41C16105C) -- 3.3V 10% (IS41LV16105C) * Byte Write and Byte Read operation via two CAS * Industrial Temperature Range -40oC to 85oC * Lead-free available These features make the IS41C16105C and IS41LV16105C ideally suited for high-bandwidth graphics, digital signal processing, high-performance computing systems, and peripheral applications. The IS41C16105C and IS41LV16105C are packaged in a 42-pin 400-mil SOJ and 400-mil 44- (50-) pin TSOP (Type II). KEY TIMING PARAMETERS Parameter -50 -60 Unit Max. RAS Access Time (trac) 50 60 ns Max. CAS Access Time (tcac) 13 15 ns Max. Column Address Access Time (taa) 25 30 ns Min. Fast Page Mode Cycle Time (tpc) 20 25 ns Min. Read/Write Cycle Time (trc) 84 104 ns Copyright (c) 2010 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that: a.) the risk of injury or damage has been minimized; b.) the user assume all such risks; and c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 1 IS41C16105C IS41LV16105C PIN CONFIGURATIONS 44(50)-Pin TSOP (Type II) 42-Pin SOJ VDD 1 44 GND VDD 1 42 GND I/O0 2 43 I/O15 I/O0 2 41 I/O15 I/O1 3 42 I/O14 I/O2 4 41 I/O13 I/O1 3 40 I/O14 I/O3 5 40 I/O12 I/O2 4 39 I/O13 VDD 6 39 GND I/O3 5 38 I/O12 I/O4 7 38 I/O11 VDD 6 37 GND I/O5 8 37 I/O10 I/O4 7 36 I/O11 I/O6 9 36 I/O9 I/O5 8 35 I/O10 I/O7 10 35 I/O8 I/O6 9 34 I/O9 NC 11 34 NC I/O7 10 33 I/O8 NC 11 32 NC NC 12 33 NC NC 13 32 LCAS NC 12 31 LCAS WE 14 31 UCAS WE 13 30 UCAS RAS 15 30 OE RAS 14 29 OE NC 16 29 A9 NC 15 28 A9 NC 17 28 A8 NC 16 27 A8 17 26 A7 A0 18 27 A7 A0 A1 19 26 A6 A1 18 25 A6 A2 20 25 A5 A2 19 24 A5 A3 21 24 A4 A3 20 23 A4 VDD 22 23 GND VDD 21 22 GND PIN DESCRIPTIONS 2 A0-A9 Address Inputs I/O0-15 Data Inputs/Outputs WE Write Enable OE Output Enable RAS Row Address Strobe UCAS Upper Column Address Strobe LCAS Lower Column Address Strobe Vdd Power GND Ground NC No Connection Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 IS41C16105C IS41LV16105C FUNCTIONAL BLOCK DIAGRAM OE WE LCAS UCAS CAS CLOCK GENERATOR WE CONTROL LOGICS CAS WE OE CONTROL LOGIC OE DATA I/O BUS COLUMN DECODERS SENSE AMPLIFIERS A0-A9 ADDRESS BUFFERS ROW DECODER REFRESH COUNTER Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 MEMORY ARRAY 1,048,576 x 16 DATA I/O BUFFERS RAS CLOCK GENERATOR RAS RAS I/O0-I/O15 3 IS41C16105C IS41LV16105C TRUTH TABLE Function Standby Read: Word Read: Lower Byte RAS H L L LCAS H L L UCAS H L H WE X H H OE X L L Address tr/tc X ROW/COL ROW/COL Read: Upper Byte L H L H L ROW/COL Write: Word (Early Write) Write: Lower Byte (Early Write) L L L L L H L L X X ROW/COL ROW/COL Write: Upper Byte (Early Write) L H L L X ROW/COL Read-Write(1,2) L L L HL LH ROW/COL I/O High-Z Dout Lower Byte, Dout Upper Byte, High-Z Lower Byte, High-Z Upper Byte, Dout Din Lower Byte, Din Upper Byte, High-Z Lower Byte, High-Z Upper Byte, Din Dout, Din LHL LHL L L L L H L L X ROW/COL ROW/COL Dout Dout L H H X X ROW/NA High-Z HL L L X X X High-Z Hidden Refresh RAS-Only Refresh CBR Refresh(4) Read Write(1,3) (2) Notes: 1. These WRITE cycles may also be BYTE WRITE cycles (either LCAS or UCAS active). 2. These READ cycles may also be BYTE READ cycles (either LCAS or UCAS active). 3. EARLY WRITE only. 4. At least one of the two CAS signals must be active (LCAS or UCAS). 4 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 IS41C16105C IS41LV16105C Functional Description Write Cycle The IS41C16105C and IS41LV16105C is a CMOS DRAM optimized for high-speed bandwidth, low power applications. During READ or WRITE cycles, each bit is uniquely addressed through the 16 address bits. These are entered ten bits (A0-A9) at a time. The row address is latched by the Row Address Strobe (RAS). The column address is latched by the Column Address Strobe (CAS). RAS is used to latch the first nine bits and CAS is used the latter nine bits. A write cycle is initiated by the falling edge of CAS and WE, whichever occurs last. The input data must be valid at or before the falling edge of CAS or WE, whichever occurs last. The IS41C16105C and IS41LV16105C has two CAS controls, LCAS and UCAS. The LCAS and UCAS inputs internally generates a CAS signal functioning in an identical manner to the single CAS input on the other 1M x 16 DRAMs. The key difference is that each CAS controls its corresponding I/O tristate logic (in conjunction with OE and WE and RAS). LCAS controls I/O0 through I/O7 and UCAS controls I/O8 through I/O15. Refresh Cycle To retain data, 1,024 refresh cycles are required in each 16 ms period. There are two ways to refresh the memory. 1. By clocking each of the 1,024 row addresses (A0 through A9) with RAS at least once every 16 ms. Any read, write, read-modify-write or RAS-only cycle refreshes the addressed row. 2. Using a CAS-before-RAS refresh cycle. CAS-beforeRAS refresh is activated by the falling edge of RAS, while holding CAS LOW. In CAS-before-RAS refresh cycle, an internal 9-bit counter provides the row addresses and the external address inputs are ignored. The IS41C16105C and IS41LV16105C CAS function is determined by the first CAS (LCAS or UCAS) transitioning LOW and the last transitioning back HIGH. The two CAS controls give the IS41C16105C and IS41LV16105C both BYTE READ and BYTE WRITE cycle capabilities. CAS-before-RAS is a refresh-only mode and no data access or device selection is allowed. Thus, the output remains in the High-Z state during the cycle. Memory Cycle Power-On A memory cycle is initiated by bring RAS LOW and it is terminated by returning both RAS and CAS HIGH. To ensures proper device operation and data integrity any memory cycle, once initiated, must not be ended or aborted before the minimum tras time has expired. A new cycle must not be initiated until the minimum precharge time trp, tcp has elapsed. After application of the Vdd supply, an initial pause of 200 s is required followed by a minimum of eight initialization cycles (any combination of cycles containing a RAS signal). During power-on, it is recommended that RAS track with Vdd or be held at a valid Vih to avoid current surges. Read Cycle A read cycle is initiated by the falling edge of CAS or OE, whichever occurs last, while holding WE HIGH. The column address must be held for a minimum time specified by tar. Data Out becomes valid only when trac, taa, tcac and toea are all satisfied. As a result, the access time is dependent on the timing relationships between these parameters. Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 5 IS41C16105C IS41LV16105C ABSOLUTE MAXIMUM RATINGS(1) Symbol Vt Parameters Voltage on Any Pin Relative to GND 5V 3.3V Rating -1.0 to +7.0 -0.5 to +4.6 Unit V Vdd Supply Voltage V Iout Pd Ta Output Current Power Dissipation Commercial Temperature Industrial Temperature Storage Temperature -1.0 to +7.0 -0.5 to +4.6 50 1 0 to +70 -40 to +85 -55 to +125 Tstg 5V 3.3V mA W C C C Note: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. RECOMMENDED OPERATING CONDITIONS (Voltages are referenced to GND.) Symbol Parameter Test Condition Min. Typ. Max. Unit Vdd Supply Voltage 5V 3.3V 4.5 3.0 5.0 3.3 5.5 3.6 V Vih Input High Voltage Vil Input Low Voltage Ta Commercial Temperature Industrial Temperature 5V 3.3V 5V 3.3V 2.0 2.0 -1.0 -0.3 0 -40 -- -- -- -- -- -- Vdd + 1.0 Vdd + 0.3 0.8 0.8 70 85 V C C 5 A 5 A -- V 0.4 V Iil Input Leakage Current Iio Output Leakage Current Voh Output High Voltage Level Vol Output Low Voltage Level Any input 0V Vin Vdd -5 Other inputs not under test = 0V Output is disabled (Hi-Z) -5 0V Vout Vdd Ioh = -5.0 mA 5V 2.4 Ioh = -2.0 mA 3.3V Iol = 4.2 mA Iol = 2.0 mA 5V 3.3V -- V CAPACITANCE(1,2) Symbol Cin1 Cin2 Cio Parameter Input Capacitance: A0-A9 Input Capacitance: RAS, UCAS, LCAS, WE, OE Data Input/Output Capacitance: I/O0-I/O15 Max. 5 7 7 Unit pF pF pF Notes: 1. Tested initially and after any design or process changes that may affect these parameters. 2. Test conditions: Ta = 25C, f = 1 MHz, 6 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 IS41C16105C IS41LV16105C ELECTRICAL CHARACTERISTICS(1) (Recommended Operating Conditions unless otherwise noted.) Symbol Parameter Test Condition Vdd/Speed Min. Idd1 RAS, LCAS, UCAS Vih Standby Current: TTL Max. Unit Com. Ind. 5V 3.3V 5V 3.3V -- -- -- -- 3 3 4 4 mA Idd2 Standby Current: CMOS RAS, LCAS, UCAS Vdd - 0.2V 5V 3.3V -- -- 2 2 mA Operating Current: RAS, LCAS, UCAS, Random Read/Write(2,3,4) Address Cycling, trc = trc (min.) Average Power Supply Current -50 -60 -- -- 160 145 mA -50 -60 -- -- 90 80 mA Operating Current: RAS = Vil, LCAS, UCAS, Fast Page Mode(2,3,4) Cycling tpc = tpc (min.) Average Power Supply Current Idd5 Refresh Current: RAS Cycling, LCAS, UCAS Vih RAS-Only(2,3) trc = trc (min.) Average Power Supply Current -50 -60 -- -- 160 145 mA Refresh Current: RAS, LCAS, UCAS Cycling CBR(2,3,5) trc = trc (min.) Average Power Supply Current -50 -60 -- -- 160 145 mA Idd3 Idd4 Idd6 Notes: 1. An initial pause of 200 s is required after power-up followed by eight RAS refresh cycles (RAS-Only or CBR) before proper device operation is assured. The eight RAS cycles wake-up should be repeated any time the tref refresh requirement is exceeded. 2. Dependent on cycle rates. 3. Specified values are obtained with minimum cycle time and the output open. 4. Column-address is changed once each Fast page cycle. 5. Enables on-chip refresh and address counters. Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 7 IS41C16105C IS41LV16105C AC CHARACTERISTICS(1,2,3,4,5,6) (Recommended Operating Conditions unless otherwise noted.) -50 -60 Symbol Parameter Min. Max. Min. Max. trc Random READ or WRITE Cycle Time 84 -- 104 -- (6, 7) trac Access Time from RAS -- 50 -- 60 (6, 8, 15) tcac Access Time from CAS -- 13 -- 15 taa Access Time from Column-Address(6) -- 25 -- 30 tras RAS Pulse Width 50 10K 60 10K trp RAS Precharge Time 30 -- 40 -- (26) tcas CAS Pulse Width 8 10K 10 10K tcp CAS Precharge Time(9, 25) 9 -- 9 -- (21) tcsh CAS Hold Time 38 -- 40 -- (10, 20) trcd RAS to CAS Delay Time 12 37 14 45 tasr trah tasc tcah tar trad tral trpc trsh trhcp tclz tcrp tod toe toed toehc toep toes trcs trrh trch twch 8 Row-Address Setup Time 0 Row-Address Hold Time 8 Column-Address Setup Time(20) 0 (20) Column-Address Hold Time 8 Column-Address Hold Time 30 (referenced to RAS) RAS to Column-Address Delay Time(11) 10 Column-Address to RAS Lead Time 25 RAS to CAS Precharge Time 5 (27) RAS Hold Time 8 RAS Hold Time from CAS Precharge 37 CAS to Output in Low-Z(15, 29) 0 (21) CAS to RAS Precharge Time 5 (19, 28, 29) Output Disable Time 3 Output Enable Time(15, 16) -- Output Enable Data Delay (Write) 20 OE HIGH Hold Time from CAS HIGH 5 OE HIGH Pulse Width 10 OE LOW to CAS HIGH Setup Time 5 (17, 20) Read Command Setup Time 0 Read Command Hold Time 0 (referenced to RAS)(12) Read Command Hold Time 0 (referenced to CAS)(12, 17, 21) Write Command Hold Time(17, 27) 8 Units ns ns ns ns ns ns ns ns ns -- -- -- -- -- 0 10 0 10 40 -- -- -- -- -- ns ns ns ns ns ns 25 -- -- -- -- -- -- 15 13 -- -- -- -- -- -- 12 30 5 10 37 0 5 3 -- 20 5 10 5 0 0 30 -- -- -- -- -- -- 15 15 -- -- -- -- -- -- ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns -- 0 -- ns -- 10 -- ns Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 IS41C16105C IS41LV16105C AC CHARACTERISTICS (Continued)(1,2,3,4,5,6) (Recommended Operating Conditions unless otherwise noted.) -50 -60 Symbol Parameter Min. Max. Min. Max. twcr Write Command Hold Time 40 -- 50 -- (referenced to RAS)(17) twp Write Command Pulse Width(17) 8 -- 10 -- twpz WE Pulse Widths to Disable Outputs 10 -- 10 -- (17) trwl Write Command to RAS Lead Time 13 -- 15 -- tcwl Write Command to CAS Lead Time(17, 21) 8 -- 10 -- twcs Write Command Setup Time(14, 17, 20) 0 -- 0 -- tdhr Data-in Hold Time (referenced to RAS) 39 -- 39 -- tach Column-Address Setup Time to CAS 15 -- 15 -- Precharge during WRITE Cycle toeh OE Hold Time from WE during 8 -- 10 -- READ-MODIFY-WRITE cycle(18) tds Data-In Setup Time(15, 22) 0 -- 0 -- (15, 22) tdh Data-In Hold Time 8 -- 10 -- trwc READ-MODIFY-WRITE Cycle Time 108 -- 133 -- trwd RAS to WE Delay Time during 64 -- 77 -- READ-MODIFY-WRITE Cycle(14) tcwd CAS to WE Delay Time(14, 20) 26 -- 32 -- (14) tawd Column-Address to WE Delay Time 39 -- 47 -- tpc Fast Page Mode READ or WRITE 20 -- 25 -- Cycle Time(24) trasp RAS Pulse Width 50 100K 60 100K (15) tcpa Access Time from CAS Precharge -- 30 -- 35 (24) tprwc READ-WRITE Cycle Time 56 -- 68 -- tcoh Data Output Hold after CAS LOW 5 -- 5 -- toff Output Buffer Turn-Off Delay from 1.6 12 1.6 15 CAS or RAS(13,15,19, 29) twhz Output Disable Delay from WE 3 10 3 10 tclch Last CAS going LOW to First CAS 10 -- 10 -- returning HIGH(23) tcsr CAS Setup Time (CBR REFRESH)(30, 20) 5 -- 5 -- tchr CAS Hold Time (CBR REFRESH)(30, 21) 8 -- 10 -- tord OE Setup Time prior to RAS during 0 -- 0 -- HIDDEN REFRESH Cycle tref Auto Refresh Period (1,024 Cycles) -- 16 -- 16 (2, 3) tt Transition Time (Rise or Fall) 1 50 1 50 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 Units ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ms ns 9 IS41C16105C IS41LV16105C AC TEST CONDITIONS Output load: Two TTL Loads and 50 pF (Vdd = 5.0V 10%) One TTL Load and 50 pF (Vdd = 3.3V 10%) Input timing reference levels: Vih = 2.4V, Vil = 0.8V (Vdd = 5.0V 10%); Vih = 2.0V, Vil = 0.8V (Vdd = 3.3V 10%) Output timing reference levels: Voh = 2.4V, Vol = 0.4V (Vdd = 5V 10%, 3.3V 10%) Notes: 1. An initial pause of 200 s is required after power-up followed by eight RAS refresh cycle (RAS-Only or CBR) before proper device operation is assured. The eight RAS cycles wake-up should be repeated any time the tref refresh requirement is exceeded. 2. Vih (MIN) and Vil (MAX) are reference levels for measuring timing of input signals. Transition times, are measured between Vih and Vil (or between Vil and Vih) and assume to be 1 ns for all inputs. 3. In addition to meeting the transition rate specification, all input signals must transit between Vih and Vil (or between Vil and Vih) in a monotonic manner. 4. If CAS and RAS = Vih, data output is High-Z. 5. If CAS = Vil, data output may contain data from the last valid READ cycle. 6. Measured with a load equivalent to one TTL gate and 50 pF. 7. Assumes that trcd trcd (MAX). If trcd is greater than the maximum recommended value shown in this table, trac will increase by the amount that trcd exceeds the value shown. 8. Assumes that trcd trcd (MAX). 9. If CAS is LOW at the falling edge of RAS, data out will be maintained from the previous cycle. To initiate a new cycle and clear the data output buffer, CAS and RAS must be pulsed for tcp. 10. Operation with the trcd (MAX) limit ensures that trac (MAX) can be met. trcd (MAX) is specified as a reference point only; if trcd is greater than the specified trcd (MAX) limit, access time is controlled exclusively by tcac. 11. Operation within the trad (MAX) limit ensures that trcd (MAX) can be met. trad (MAX) is specified as a reference point only; if trad is greater than the specified trad (MAX) limit, access time is controlled exclusively by taa. 12. Either trch or trrh must be satisfied for a READ cycle. 13. toff (MAX) defines the time at which the output achieves the open circuit condition; it is not a reference to Voh or Vol. 14. twcs, trwd, tawd and tcwd are restrictive operating parameters in LATE WRITE and READ-MODIFY-WRITE cycle only. If twcs twcs (MIN), the cycle is an EARLY WRITE cycle and the data output will remain open circuit throughout the entire cycle. If trwd trwd (MIN), tawd tawd (MIN) and tcwd tcwd (MIN), the cycle is a READ-WRITE cycle and the data output will contain data read from the selected cell. If neither of the above conditions is met, the state of I/O (at access time and until CAS and RAS or OE go back to Vih) is indeterminate. OE held HIGH and WE taken LOW after CAS goes LOW result in a LATE WRITE (OE-controlled) cycle. 15. Output parameter (I/O) is referenced to corresponding CAS input, I/O0-I/O7 by LCAS and I/O8-I/O15 by UCAS. 16. During a READ cycle, if OE is LOW then taken HIGH before CAS goes HIGH, I/O goes open. If OE is tied permanently LOW, a LATE WRITE or READ-MODIFY-WRITE is not possible. 17. Write command is defined as WE going low. 18. LATE WRITE and READ-MODIFY-WRITE cycles must have both tod and toeh met (OE HIGH during WRITE cycle) in order to ensure that the output buffers will be open during the WRITE cycle. The I/Os will provide the previously written data if CAS remains LOW and OE is taken back to LOW after toeh is met. 19. The I/Os are in open during READ cycles once tod or toff occur. 20. The first CAS edge to transition LOW. 21. The last CAS edge to transition HIGH. 22. These parameters are referenced to CAS leading edge in EARLY WRITE cycles and WE leading edge in LATE WRITE or READMODIFY-WRITE cycles. 23. Last falling CAS edge to first rising CAS edge. 24. Last rising CAS edge to next cycle's last rising CAS edge. 25. Last rising CAS edge to first falling CAS edge. 26. Each CAS must meet minimum pulse width. 27. Last CAS to go LOW. 28. I/Os controlled, regardless UCAS and LCAS. 29. The 3 ns minimum is a parameter guaranteed by design. 30. Enables on-chip refresh and address counters. 10 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 IS41C16105C IS41LV16105C FAST-PAGE-MODE READ CYCLE tRC tRAS tRP RAS tCSH tCRP tRSH tCAS tCLCH tRCD tRRH UCAS/LCAS tAR tRAD tASR ADDRESS tRAH tRAL tCAH tASC Row Column Row tRCS tRCH WE tAA tRAC tCAC tCLC I/O tOFF(1) Open Open Valid Data tOE tOD OE tOES Don't Care Note: 1. toff is referenced from rising edge of RAS or CAS, whichever occurs last. Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 11 IS41C16105C IS41LV16105C FAST PAGE MODE READ-MODIFY-WRITE CYCLE tRASP tRP RAS tPRWC tCAS tCSH tCRP tCAS tRCD tRSH tCAS tCP tCRP tCP UCAS/LCAS tAR tRAH tRAD tASC tASR ADDRESS tCPWD tRAL tCAH tCPWD Row tCAH tAR Column tASC Column tCWL tRWD tAWD tCWD tRCS tCAH tASC Column tCWL tRWL tCWL tAWD tCWD tWP tAWD tCWD tWP tWP WE tAA tAA tCAC tCAC tOEA OE tCAC tOEA tOEZ tOED tRAC OUT IN tOEA tOEZ tOED tDH tDS tCLZ tCLZ I/O0-I/O15 tAA tDS OUT IN tDH tOEZ tOED tCLZ OUT tDS tDH IN Don't Care 12 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 IS41C16105C IS41LV16105C FAST-PAGE-MODE EARLY WRITE CYCLE (OE = DON'T CARE) tRC tRAS tRP RAS tCSH tCRP tRSH tCAS tCLCH tRCD UCAS/LCAS tAR tRAD tASR ADDRESS tRAH tRAL tCAH tACH tASC Row Column Row tCWL tRWL tWCR tWCS tWCH tWP WE tDHR tDS I/O tDH Valid Data Don't Care Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 13 IS41C16105C IS41LV16105C FAST-PAGE-MODE READ WRITE CYCLE (LATE WRITE and READ-MODIFY-WRITE Cycles) tRWC tRAS tRP RAS tCSH tCRP tRSH tCAS tCLCH tRCD UCAS/LCAS tAR tRAD tASR tRAH tRAL tCAH tASC tACH ADDRESS Row Column Row tRWD tCWL tRWL tCWD tRCS tAWD tWP WE tAA tRAC tCAC tCLZ I/O tDS Open Valid DOUT tOE tOD tDH Valid DIN Open tOEH OE Don't Care 14 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 IS41C16105C IS41LV16105C FAST PAGE MODE EARLY WRITE CYCLE tRASP tRP RAS tCRP tCAS tRCD tRHCP tRSH tCAS tPC tCAS tCSH tCP tCP tCRP UCAS/LCAS tAR tRAH tRAD tASC tASR ADDRESS Row tCAH tASC tAR Column tWCH tASC Column tCWL tWCS tRAL tCAH Column tCWL tCWL tWCH tWCS tWCS tWP tCAH tWP tWCH tWP WE tWCR OE tDHR tDS I/O0-I/O15 tDH Valid DIN tDS tDH Valid DIN tDS tDH Valid DIN Don't Care Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 15 IS41C16105C IS41LV16105C AC WAVEFORMS READ CYCLE (With WE-Controlled Disable) RAS tCSH tCRP tRCD tCP tCAS UCAS/LCAS tAR tRAD tASR ADDRESS tRAH tCAH tASC Row tASC Column Column tRCS tRCH tRCS WE tAA tRAC tCAC tCLZ Open I/O tWHZ tCLZ Valid Data Open tOE tOD OE Don't Care RAS-ONLY REFRESH CYCLE (OE, WE = DON'T CARE) tRC tRAS tRP RAS tCRP tRPC UCAS/LCAS tASR ADDRESS I/O tRAH Row Row Open Don't Care 16 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 IS41C16105C IS41LV16105C CBR REFRESH CYCLE (Addresses; WE, OE = DON'T CARE) tRP tRAS tRP tRAS RAS tCHR tRPC tCP tCHR tRPC tCSR tCSR UCAS/LCAS Open I/O HIDDEN REFRESH CYCLE(1) (WE = HIGH; OE = LOW) tRAS tRP tRAS RAS tCRP tRCD tASR tRAD tRAH tASC tRSH tCHR UCAS/LCAS tAR ADDRESS Row tRAL tCAH Column tAA tRAC tOFF(2) tCAC tCLZ I/O Open Valid Data tOE Open tOD tORD OE Don't Care Notes: 1. A Hidden Refresh may also be performed after a Write Cycle. In this case, WE = LOW and OE = HIGH. 2. toff is referenced from rising edge of RAS or CAS, whichever occurs last. Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 17 IS41C16105C IS41LV16105C ORDERING INFORMATION : 5V Industrial Range: -40oC to 85oC Speed (ns) 50 Order Part No. Package IS41C16105C-50KI IS41C16105C-50KLI IS41C16105C-50TI IS41C16105C-50TLI 400-mil SOJ 400-mil SOJ, Lead-free 400-mil TSOP (Type II) 400-mil TSOP (Type II), Lead-free ORDERING INFORMATION : 3.3V Industrial Range: -40oC to 85oC Speed (ns) 50 Order Part No. Package IS41LV16105C-50KI IS41LV16105C-50KLI IS41LV16105C-50TI IS41LV16105C-50TLI 400-mil SOJ 400-mil SOJ, Lead-free 400-mil TSOP (Type II) 400-mil TSOP (Type II), Lead-free Note: The -50 speed option supports 50ns and 60ns timing specifications. 18 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 IS41C16105C IS41LV16105C Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010 19 IS41C16105C IS41LV16105C 20 Integrated Silicon Solution, Inc. -- 1-800-379-4774 Rev. 00A 04/09/2010