Zener Diode Features: * * * * Low profile package. Excellent clamping capability. Glass passivity junction. Vz-tolerance 5%. Application: Voltage stabilization. Absolute Maximum Ratings Tj = 25C Parameter Test Conditions Symbol Value Unit Power dissipation Tamb 75C Pv 5 W Z-current - Iz Pv / Vz mA Junction temperature - Tj 150 Storage temperature range - Tstg -65 to +150 C Stresses exceeding maximum ratings may damage the device. Maximum ratings are stress ratings only. Functional operation above the recommended operating conditions is not implied. Extended exposure to stresses above the recommended operating conditions may affect device reliability. Electrical Characteristics Tj = 25C Parameter Test Conditions Symbol Maximum Unit Forward voltage IF = 1A VF 1.2 V http://www.farnell.com http://www.newark.com http://www.cpc.co.uk Page <1> 28/06/11 V1.1 Zener Diode Specification Table VZnom1) 1) 2) 3) 4) IZT for ZzT ZZK at IZK = 1 mA IR at VR IR2) VZ3) lZM4) Part Number V mA A V A V mA 5.1 240 1.5 400 1 1 14.4 0.39 930 1N5338B 5.6 220 1 400 1 2 13.4 0.25 865 1N5339B 6 200 1 300 1 3 12.7 0.19 790 1N5340B 6.2 200 1 200 1 3 12.4 0.1 765 1N5341B 6.8 175 1 200 10 5.2 11.5 0.15 700 1N5342B 7.5 175 1.5 200 10 5.7 10.7 0.15 630 1N5343B 8.2 150 1.5 200 10 6.2 10 0.2 580 1N5344B 9.1 150 2 150 7.5 6.9 9.2 0.22 520 1N5346B 10 125 2 125 5 7.6 8.6 0.22 475 1N5347B 11 125 2.5 125 5 8.4 8 0.25 430 1N5348B 12 100 2.5 125 2 9.1 7.5 0.25 395 1N5349B 13 100 2.5 100 1 9.9 7 0.25 365 1N5350B 14 100 2.5 75 1 10.6 6.7 0.25 340 1N5351B 15 75 2.5 75 1 11.5 6.3 0.25 315 1N5352B 16 75 2.5 75 1 12.2 6 0.3 295 1N5353B 17 70 2.5 75 0.5 12.9 5.8 0.35 280 1N5354B 18 65 2.5 75 0.5 13.7 5.5 0.4 265 1N5355B 22 50 3.5 75 0.5 16.7 4.7 0.45 216 1N5358B 24 50 3.5 100 0.5 18.2 4.4 0.55 198 1N5359B 27 50 5 120 0.5 20.6 4.1 0.6 176 1N5361B 30 40 8 140 0.5 22.8 3.7 0.6 158 1N5363B 33 40 10 150 0.5 25.1 3.5 0.6 144 1N5364B 36 30 11 160 0.5 27.4 3.3 0.65 132 1N5365B Zener voltage (Vz): Based on DC-measurement at thermal equilibrium while maintaining the lead temperature (TL) at 25C, 9.5 mm (3/8") from the diode body. Surge current (IR) is specified as the maximum allowable peak, non-recurrent square-wave current with a plus width, PW, of 8.3 ms. Voltage regulation (Vz): Test conditions for voltage are as below, Vz measurements are made at 10% and then at 50% of the Iz max value listed in the electrical characteristics table. The test current time duration for each Vz measurements is 40 10 ms (TA = 25C +8, -2C). Maximum regulator current (IZM): The maximum current shown is based on the maximum voltage of a 5% type unit; therefore, it applies only to the B-suffix device. The actual IZM for any device may not exceed the value of 5 watts divided by the actual Vz of the device. TL = 75C at 9.5 mm (3/8") from the diode body. http://www.farnell.com http://www.newark.com http://www.cpc.co.uk Page <2> 28/06/11 V1.1 Zener Diode Case : moulded plastic DO-15 Polarity : Cathode band Dimensions Dimensions Inches Minimum mm Maximum Minimum Maximum A 1 - 25.4 - B 0.23 0.3 5.8 7.6 C 0.026 0.034 0.7 0.9 D 0.104 0.14 2.6 3.6 Disclaimer This data sheet and its contents (the "Information") belong to the Premier Farnell Group (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. SPC Multicomp is the registered trademark of the Group. (c) Premier Farnell plc 2011. http://www.farnell.com http://www.newark.com http://www.cpc.co.uk Page <3> 28/06/11 V1.1