Zener Diode
Page <1> 28/06/11 V1.1
http://www.farnell.com
http://www.newark.com
http://www.cpc.co.uk
Features:
•Low profile package.
•Excellent clamping capability.
•Glass passivity junction.
•Vz-tolerance ±5%.
Application:
Voltage stabilization.
Parameter Test Conditions Symbol Value Unit
Power dissipation Tamb ≤ 75°C Pv5 W
Z-current - IzPv / VzmA
Junction temperature -Tj150
°C
Storage temperature range -Tstg -65 to +150
Stresses exceeding maximum ratings may damage the device. Maximum ratings are stress ratings only. Functional operation above
the recommended operating conditions is not implied. Extended exposure to stresses above the recommended operating conditions
may affect device reliability.
Electrical Characteristics Tj= 25°C
Parameter Test Conditions Symbol Maximum Unit
Forward voltage IF= 1A VF1.2 V
Absolute Maximum Ratings Tj= 25°C
Zener Diode
Page <2> 28/06/11 V1.1
http://www.farnell.com
http://www.newark.com
http://www.cpc.co.uk
Specification Table
VZnom1) IZT for ZzT
ZZK at
IZK = 1 mA
IRat VRIR2) ∆∆VZ3) lZM4)
Part Number
V mA ΩΩΩΩµA V A V mA
5.1 240 1.5 400 1 1 14.4 0.39 930 1N5338B
5.6 220 1 400 1 2 13.4 0.25 865 1N5339B
6 200 1 300 1 3 12.7 0.19 790 1N5340B
6.2 200 1 200 1 3 12.4 0.1 765 1N5341B
6.8 175 1 200 10 5.2 11.5 0.15 700 1N5342B
7.5 175 1.5 200 10 5.7 10.7 0.15 630 1N5343B
8.2 150 1.5 200 10 6.2 10 0.2 580 1N5344B
9.1 150 2 150 7.5 6.9 9.2 0.22 520 1N5346B
10 125 2 125 5 7.6 8.6 0.22 475 1N5347B
11 125 2.5 125 5 8.4 8 0.25 430 1N5348B
12 100 2.5 125 2 9.1 7.5 0.25 395 1N5349B
13 100 2.5 100 1 9.9 7 0.25 365 1N5350B
14 100 2.5 75 1 10.6 6.7 0.25 340 1N5351B
15 75 2.5 75 1 11.5 6.3 0.25 315 1N5352B
16 75 2.5 75 1 12.2 6 0.3 295 1N5353B
17 70 2.5 75 0.5 12.9 5.8 0.35 280 1N5354B
18 65 2.5 75 0.5 13.7 5.5 0.4 265 1N5355B
22 50 3.5 75 0.5 16.7 4.7 0.45 216 1N5358B
24 50 3.5 100 0.5 18.2 4.4 0.55 198 1N5359B
27 50 5 120 0.5 20.6 4.1 0.6 176 1N5361B
30 40 8 140 0.5 22.8 3.7 0.6 158 1N5363B
33 40 10 150 0.5 25.1 3.5 0.6 144 1N5364B
36 30 11 160 0.5 27.4 3.3 0.65 132 1N5365B
1) Zener voltage (Vz): Based on DC-measurement at thermal equilibrium while maintaining the lead temperature (TL) at 25°C,
9.5 mm (3/8”) from the diode body.
2) Surge current (IR) is specified as the maximum allowable peak, non-recurrent square-wave current with a plus width,
PW, of 8.3 ms.
3) Voltage regulation (∆Vz): Test conditions for voltage are as below, Vzmeasurements are made at 10% and then at 50% of the
Izmax value listed in the electrical characteristics table. The test current time duration for each Vzmeasurements is 40 ±10 ms
(TA= 25°C +8, -2°C).
4) Maximum regulator current (IZM): The maximum current shown is based on the maximum voltage of a 5% type unit; therefore, it
applies only to the B-suffix device. The actual IZM for any device may not exceed the value of 5 watts divided by the actual Vzof
the device. TL= 75°C at 9.5 mm (3/8”) from the diode body.
Zener Diode
Page <3> 28/06/11 V1.1
http://www.farnell.com
http://www.newark.com
http://www.cpc.co.uk
Disclaimer This data sheet and its contents (the "Information") belong to the Premier Farnell Group (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes
in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied.
The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data
sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage
resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded.
This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. SPC Multicomp is the registered trademark of the Group. © Premier Farnell plc 2011.
Dimensions
Dimensions
Inches mm
Minimum Maximum Minimum Maximum
A 1 - 25.4 -
B 0.23 0.3 5.8 7.6
C 0.026 0.034 0.7 0.9
D 0.104 0.14 2.6 3.6
Case : moulded plastic DO-15
Polarity : Cathode band
