TPS768xxQ www.ti.com SLVS211L - JUNE 1999 - REVISED JANUARY 2006 FAST TRANSIENT RESPONSE, 1-A LOW-DROPOUT VOLTAGE REGULATORS FEATURES * * * * * * * * * DESCRIPTION Input Voltage Range: 2.7 V to 10 V Low-Dropout Voltage: 230 mV typical at 1 A (TPS76850) 2% Tolerance Over Specified Conditions for Fixed-Output Versions Open Drain Power Good (See TPS767xx for Power-On Reset With 200-ms Delay Option) Ultralow 85 A Typical Quiescent Current Available in 1.5-V, 1.8-V, 2.5-V, 2.7-V, 2.8-V, 3.0-V, 3.3-V, 5.0-V Fixed Output and Adjustable (1.2 V to 5.5 V) Versions Fast Transient Response Thermal Shutdown Protection SOIC-8 (D) and TSSOP-20 (PWP) Package D PACKAGE (Top View) GND 1 8 PG EN 2 7 FB/NC IN 3 6 OUT IN 4 5 OUT This device is designed to have a fast transient response and be stable with 10 F capacitors. This combination provides high performance at a reasonable cost. Since the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 230 mV at an output current of 1 A for the TPS76850) and is directly proportional to the output current. Additionally, because the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent of output loading (typically 85 A over the full range of output current, 0 mA to 1 A). These two key specifications yield a significant improvement in operating life for battery-powered systems. This LDO family also features a shutdown mode; applying a TTL high signal to EN (enable) shuts down the regulator, reducing the quiescent current to less than 1 A at TJ = 25C. Power good (PG) is an active high output, which can be used to implement a power-on reset or a low-battery indicator. TPS768xx VI 6 IN PG 16 PG 7 IN OUT 0.1 F PWP PACKAGE (Top View) 5 EN OUT 14 VO 13 + GND/HSINK 1 20 GND/HSINK GND/HSINK 2 19 GND/HSINK GND 3 18 NC NC 4 17 NC EN 5 16 PG IN 6 15 FB/NC IN 7 14 OUT NC 8 13 OUT GND/HSINK 9 12 GND/HSINK GND/HSINK 10 11 GND/HSINK GND Co 10 F 3 Figure 1. Typical Application Configuration (For Fixed Output Options) NC = No Internal Connection Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1999-2006, Texas Instruments Incorporated TPS768xxQ www.ti.com SLVS211L - JUNE 1999 - REVISED JANUARY 2006 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) VOUT (2) PRODUCT TPS768xxQyyyz (1) (2) XX is nominal output voltage (for example, 28 = 2.8 V, 285 = 2.85 V, 01 = Adjustable). YYY is package designator. Z is package quantity. For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. Custom output voltages are available; minimum order quantities may apply. Contact factory for details and availability. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) VALUE Input voltage range, VI (2) -0.3 V to 13.5 V Voltage range at EN -0.3 V to VI + 0.3 V Maximum PG voltage 16.5 V Peak output current Internally limited Continuous total power dissipation See Dissipation Rating Table Output voltage, VO (OUT, FB) 7V Operating junction temperature range, TJ -40C to +125C Storage temperature range, Tstg -65C to +150C ESD rating, HBM (1) (2) 2 kV Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to network terminal ground. DISSIPATION RATING TABLE--FREE-AIR TEMPERATURES PACKAGE D PWP (1) (1) AIR FLOW (CFM) TA < +25C POWER RATING DERATING FACTOR ABOVE TA = +25C TA = +70C POWER RATING TA = +85C POWER RATING 0 568.18 mW 5.6818 mW/C 312.5 mW 227.27 mW 250 904.15 mW 9.0415 mW/C 497.28 mW 361.66 mW 0 3.1 W 30.7 mW/C 1.7 W 1.2 W 250 4.1 W 41.2 mW/C 2.3 W 1.6 W This parameter is measured with the recommended copper heat sink pattern on a 4-layer, 5-in x 5-in PCB, 1 oz. copper, 4-in x 4-in coverage (4 in2). RECOMMENDED OPERATING CONDITIONS MIN MAX Input voltage, VI (1) 2.7 10 V Output voltage range, VO 1.2 5.5 V 0 1.0 A -40 +125 C Output current, IO (2) Operating junction temperature, TJ (2) (1) (2) 2 UNIT Minimum VIN = VOUT + VDO or 2.7 V, whichever is greater. Continuous current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the device operate under conditions beyond those specified in this table for extended periods of time. Submit Documentation Feedback TPS768xxQ www.ti.com SLVS211L - JUNE 1999 - REVISED JANUARY 2006 ELECTRICAL CHARACTERISTICS over recommended operating free-air temperature range, VI = VO(typ)+ 1 V, IO = 1 mA, EN = 0 V, CO = 10 F (unless otherwise noted). PARAMETER TEST CONDITIONS VOUT Accuracy -40C TJ +125C, VO + 1 V VIN 10V (1), 10 A IO 1A Quiescent current (GND current) EN = 0V Output voltage line regulation (VO/VO) (1) (1) (2) MIN TYP MAX (0.98)VO VO (1.02)VO 10 A < IO < 1 A, TJ = +25C 85 IO = 1 A, TJ = -40C to +125C 125 VO + 1 V < VI 10 V, TJ = +25C Load regulation Output noise voltage (TPS76818) BW = 200 Hz to 100 kHz, CO = 10 F, IC = 1 A, TJ = +25C Output current limit VO = 0 V 1.2 Thermal shutdown junction temperature VEN = VI, TJ = +25C, 2.7 V < VI < 10 V Standby current TPS76801 %/V mV 55 Vrms 1.7 Power Good (PG) 1 A 2 f = 1 kHz, CO = 10 F, TJ = +25C IO(PG) = 300 A Trip threshold voltage VO decreasing Hysteresis voltage Measured at VO Output low voltage VI = 2.7 V, IO(PG) = 1 mA Leakage current V(PG) = 5 V Enable pin current (IEN) V TPS76828 TPS76830 (3) TPS76833 TPS76850 (1) (2) (3) 60 0.5 1 VEN = VI 1 IO = 1 A, TJ = +25C 0 %VO V 1 A 1 A 500 825 450 IO = 1 A, TJ = -40C to +125C IO = 1 A, TJ = +25C %VO 0.4 1 IO = 1 A, TJ = -40C to +125C IO = 1 A, TJ = +25C V 98 0.15 V dB 1.1 92 VEN = 0 V A nA 0.9 (1) A C 1.7 Minimum input voltage for valid PG Dropout voltage 2 150 Low-level enable input voltage Power-supply ripple rejection A 3 10 VFB = 1.5 V High-level enable input voltage V 0.01 VEN = VI, TJ = -40C to +125C, 2.7 V < VI < 10 V FB pin current, IFB UNIT 675 350 IO = 1 A, TJ = -40C to +125C mV 575 IO = 1 A, TJ = +25C 230 IO = 1 A, TJ = -40C to +125C 380 Minimum IN operating voltage is 2.7 V or VO(typ) + 1 V, whichever is greater. Maximum IN voltage 10 V. V Imax2.7V Line Reg. (mV) (% V) V O 1000 100 If VO 1.8 V then VImax = 10 V, VImin = 2.7 V: V ImaxVO1V Line Reg. (mV) (% V) V O 1000 100 If VO 2.5 V then VImax = 10 V, VImin = VO + 1 V: IN voltage equals VO(typ) - 100 mV; TPS76801 output voltage set to 3.3 V nominal with external resistor divider. TPS76815, TPS76818, TPS76825, and TPS76827 dropout voltage limited by input voltage range limitations (that is, TPS76830 input voltage must drop to 2.9 V for the purpose of this test). Submit Documentation Feedback 3 TPS768xxQ www.ti.com SLVS211L - JUNE 1999 - REVISED JANUARY 2006 FUNCTIONAL BLOCK DIAGRAM--Adjustable Version IN EN PG _ + OUT + _ R1 Vref = 1.1834 V FB/NC R2 GND External to the device FUNCTIONAL BLOCK DIAGRAM--Fixed-Voltage Version IN EN PG _ + OUT + _ R1 Vref = 1.1834 V R2 GND Terminal Functions NAME 4 SOIC-8 (D) PIN NO. TSSOP-20 (PWP) PIN NO. DESCRIPTION GND 1 3 GND/HSINK -- 1, 2, 9-12, 19, 20 Regulator ground NC -- 4, 8, 17, 18 No connect Regulator ground and heatsink EN 2 5 Enable input IN 3, 4 6, 7 Input voltage OUT 5, 6 13, 14 FB/NC 7 15 Feedback input voltage for adjustable device (no connect for fixed options) PG 8 16 PG output Regulated output voltage Submit Documentation Feedback TPS768xxQ www.ti.com SLVS211L - JUNE 1999 - REVISED JANUARY 2006 TYPICAL CHARACTERISTICS TPS76833 OUTPUT VOLTAGE vs OUTPUT CURRENT TPS76815 OUTPUT VOLTAGE vs OUTPUT CURRENT 3.2835 1.4985 VI = 4.3 V TA = 25C 1.4980 3.2825 VO - Output Voltage - V VO - Output Voltage - V 3.2830 3.2820 3.2815 3.2810 3.2805 1.4975 1.4970 1.4965 1.4960 1.4955 3.2800 1.4950 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 IO - Output Current - A 0.8 0.9 1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 IO - Output Current - A Figure 2. Figure 3. TPS76825 OUTPUT VOLTAGE vs OUTPUT CURRENT TPS76833 OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 2.4960 3.32 VI = 3.5 V TA = 25C 2.4955 VI = 4.3 V 3.31 VO - Output Voltage - V 2.4950 VO - Output Voltage - V VI = 2.7 V TA = 25C 2.4945 2.4940 2.4935 2.4930 3.30 3.29 IO = 1 A IO = 1 mA 3.28 3.27 3.26 2.4925 2.4920 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 3.25 -60 -40 -20 0 20 40 60 80 100 120 140 TA - Free-Air Temperature - C IO - Output Current - A Figure 4. Figure 5. Submit Documentation Feedback 5 TPS768xxQ www.ti.com SLVS211L - JUNE 1999 - REVISED JANUARY 2006 TYPICAL CHARACTERISTICS (continued) TPS76815 OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE TPS76825 OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 1.515 2.515 VI = 3.5 V VI = 2.7 V 2.510 VO - Output Voltage - V VO - Output Voltage - V 1.510 1.505 1.500 IO = 1 A IO = 1 mA 1.495 1.490 2.505 2.500 IO = 1 A 2.495 IO = 1 mA 2.490 2.485 1.485 -60 -40 -20 0 20 40 60 80 2.480 -60 -40 100 120 140 TA - Free-Air Temperature - C -20 0 20 40 60 80 100 120 TA - Free-Air Temperature - C Figure 6. Figure 7. TPS76833 GROUND CURRENT vs FREE-AIR TEMPERATURE TPS76815 GROUND CURRENT vs FREE-AIR TEMPERATURE 92 100 VI = 2.7 V 90 VI = 4.3 V 95 86 84 82 IO = 1 mA 80 IO = 1 A 78 IO = 500 mA 76 Ground Current - A Ground Current - A 88 90 IO = 1 A IO = 1 mA 85 IO = 500 mA 80 74 72 -60 -40 -20 0 20 40 60 80 100 120 140 75 -60 -40 -20 TA - Free-Air Temperature - C Figure 8. 6 0 20 40 Figure 9. Submit Documentation Feedback 60 80 100 120 140 TA - Free-Air Temperature - C TPS768xxQ www.ti.com SLVS211L - JUNE 1999 - REVISED JANUARY 2006 TYPICAL CHARACTERISTICS (continued) TPS76833 POWER-SUPPLY RIPPLE REJECTION vs FREQUENCY TPS76833 OUTPUT SPECTRAL NOISE DENSITY vs FREQUENCY 10-5 VI = 4.3 V Co = 10 F IO = 1 A TA = 25C 80 70 Output Spectral Noise Density - V Hz PSRR - Power Supply Ripple Rejection - dB 90 60 50 40 30 20 10 0 -10 10 100 1k 10k 100k VI = 4.3 V Co = 10 F TA = 25C IO = 7 mA 10-6 IO = 1 A 10-7 10-8 102 1M 103 f - Frequency - Hz Figure 10. Figure 11. INPUT VOLTAGE (MIN) vs OUTPUT VOLTAGE TPS76833 OUTPUT IMPEDANCE vs FREQUENCY 0 VI = 4.3 V Co = 10 F TA = 25C IO = 1 A Zo - Output Impedance - TA = 25C VI - Input Voltage (Min) - V 105 f - Frequency - Hz 4 TA = 125C 3 TA = -40C 2.7 2 1.5 104 1.75 2 2.25 2.5 2.75 3 3.25 3.5 IO = 1 mA 10-1 IO = 1 A 10-2 101 VO - Output Voltage - V Figure 12. 102 103 104 f - Frequency - kHz 105 106 Figure 13. Submit Documentation Feedback 7 TPS768xxQ www.ti.com SLVS211L - JUNE 1999 - REVISED JANUARY 2006 TYPICAL CHARACTERISTICS (continued) TPS76833 DROPOUT VOLTAGE vs FREE-AIR TEMPERATURE TPS76815 LINE TRANSIENT RESPONSE VI - Input Voltage - V 103 IO = 1 A 101 2.7 IO = 10 mA 100 VO - Change in Output Voltage - mV VDO - Dropout Voltage - mV 102 3.7 10-1 IO = 0 Co = 10 F 10-2 -60 -40 -20 0 20 40 60 80 100 120 140 10 0 Co = 10 F TA = 25C -10 0 20 40 60 TA - Free-Air Temperature - C Figure 15. TPS76815 LOAD TRANSIENT RESPONSE TPS76833 LINE TRANSIENT RESPONSE VO - Change in Output Voltage - mV Co = 10 F TA = 25C 50 0 -50 VI - Input Voltage - V Figure 14. 100 VO - Change in Output Voltage - mV I O - Output Current - A Co = 10 F TA = 25C 5.3 4.3 -100 1 0.5 0 0 100 200 300 400 500 600 700 800 900 1000 t - Time - s 10 0 -10 0 Figure 16. 8 80 100 120 140 160 180 200 t - Time - s 20 40 60 80 100 120 140 160 180 200 t - Time - s Figure 17. Submit Documentation Feedback TPS768xxQ www.ti.com SLVS211L - JUNE 1999 - REVISED JANUARY 2006 TYPICAL CHARACTERISTICS (continued) TPS76833 OUTPUT VOLTAGE vs TIME (AT START-UP) TPS76833 LOAD TRANSIENT RESPONSE VO- Output Voltage - V 4 Co = 10 F TA = 25C 50 0 -50 -100 Co = 10 F IO = 1 A TA = 25C 3 2 1 0 1 Enable Pulse - V I O - Output Current - A VO - Change in Output Voltage - mV 100 0.5 0 0 100 200 300 400 500 600 700 800 900 1000 t - Time - s 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 t - Time - ms 0.9 1 Figure 18. Figure 19. TPS76801 DROPOUT VOLTAGE vs INPUT VOLTAGE TEST CIRCUIT FOR TYPICAL REGIONS OF STABILITY (Figure 22 through Figure 25) (Fixed Output Options) 900 IO = 1 A VDO - Dropout Voltage - mV 800 700 To Load VI 600 IN OUT + 500 TA = 25C 400 EN TA = 125C Co GND RL ESR 300 200 TA = -40C 100 0 2.5 3 3.5 4 VI - Input Voltage - V 4.5 5 Figure 20. Figure 21. Submit Documentation Feedback 9 TPS768xxQ www.ti.com SLVS211L - JUNE 1999 - REVISED JANUARY 2006 TYPICAL CHARACTERISTICS (continued) Equivalent series resistance (ESR) refers to the total series resistance, including the ESR of the capacitor, any series resistance added externally, and PWB trace resistance to CO. TYPICAL REGION OF STABILITY EQUIVALENT SERIES RESISTANCE vs OUTPUT CURRENT TYPICAL REGION OF STABILITY EQUIVALENT SERIES RESISTANCE vs OUTPUT CURRENT 10 ESR - Equivalent Series Resistance - ESR - Equivalent Series Resistance - 10 Region of Instability 1 VO = 3.3 V Co = 4.7 F VI = 4.3 V TA = 25C Region of Stability 0.1 VO = 3.3 V Co = 4.7 F VI = 4.3 V TJ = 125C Region of Stability 0.1 Region of Instability 0.01 0 200 400 600 800 0 1000 200 400 600 800 IO - Output Current - mA IO - Output Current - mA Figure 22. Figure 23. TYPICAL REGION OF STABILITY EQUIVALENT SERIES RESISTANCE vs OUTPUT CURRENT TYPICAL REGION OF STABILITY EQUIVALENT SERIES RESISTANCE vs OUTPUT CURRENT 1000 10 ESR - Equivalent Series Resistance - 10 ESR - Equivalent Series Resistance - 1 Region of Instability 0.01 Region of Instability 1 VO = 3.3 V Co = 22 F VI = 4.3 V TA = 25C Region of Stability 0.1 Region of Instability Region of Instability 1 VO = 3.3 V Co = 22 F VI = 4.3 V TJ = 125C Region of Stability 0.1 Region of Instability 0.01 0.01 0 10 Region of Instability 200 400 600 800 1000 0 200 400 600 IO - Output Current - mA IO - Output Current - mA Figure 24. Figure 25. Submit Documentation Feedback 800 1000 TPS768xxQ www.ti.com SLVS211L - JUNE 1999 - REVISED JANUARY 2006 APPLICATION INFORMATION The TPS768xxQ family includes eight fixed-output voltage regulators (1.5 V, 1.8 V, 2.5 V, 2.7 V, 2.8 V, 3.0 V, 3.3 V, and 5.0 V), and offers an adjustable device, the TPS76801 (adjustable from 1.2 V to 5.5 V). DEVICE OPERATION The TPS768xxQ features very low quiescent current, which remains virtually constant even with varying loads. Conventional LDO regulators use a PNP pass element, the base current of which is directly proportional to the load current through the regulator (IB = IC/). The TPS768xxQ uses a PMOS transistor to pass current; because the gate of the PMOS is voltage driven, operating current is low and invariable over the full load range. Another pitfall associated with the PNP-pass element is its tendency to saturate when the device goes into dropout. The resulting drop in forces an increase in IB to maintain the load. During power up, this translates to large start-up currents. Systems with limited supply current may fail to start up. In battery-powered systems, it means rapid battery discharge when the voltage decays below the minimum required for regulation. The TPS768xxQ quiescent current remains low even when the regulator drops out, eliminating both problems. The TPS768xxQ family also features a shutdown mode that places the output in the high-impedance state (essentially equal to the feedback-divider resistance) and reduces quiescent current to 2 A. If the shutdown feature is not used, EN should be tied to ground. MINIMUM LOAD REQUIREMENTS The TPS768xxQ family is stable even at zero load; no minimum load is required for operation. FB - PIN CONNECTION (ADJUSTABLE VERSION ONLY) The FB pin is an input pin to sense the output voltage and close the loop for the adjustable option. The output voltage is sensed through a resistor divider network to close the loop as shown in Figure 27. Normally, this connection should be as short as possible; however, the connection can be made near a critical circuit to improve performance at that point. Internally, FB connects to a high-impedance wide-bandwidth amplifier and noise pickup feeds through to the regulator output. Routing the FB connection to minimize/avoid noise pickup is essential. EXTERNAL CAPACITOR REQUIREMENTS An input capacitor is not usually required; however, a ceramic bypass capacitor (0.047 F or larger) improves load transient response and noise rejection if the TPS768xxQ is located more than a few inches from the power supply. A higher-capacitance electrolytic capacitor may be necessary if large (hundreds of milliamps) load transients with fast rise times are anticipated. Like all low dropout regulators, the TPS768xxQ requires an output capacitor connected between OUT and GND to stabilize the internal control loop. The minimum recommended capacitance value is 10 F and the ESR (equivalent series resistance) must be between 60 m and 1.5 . Capacitor values 10 F or larger are acceptable, provided the ESR is less than 1.5 . Solid tantalum electrolytic, aluminum electrolytic, and multilayer ceramic capacitors are all suitable, provided they meet the requirements described above. Submit Documentation Feedback 11 TPS768xxQ www.ti.com SLVS211L - JUNE 1999 - REVISED JANUARY 2006 APPLICATION INFORMATION (continued) TPS768xx 6 VI IN 7 C1 0.1 F PG 16 PG 250 k IN OUT 5 EN OUT 14 VO 13 + Co 10 F GND 3 Figure 26. Typical Application Circuit (Fixed Versions) The output voltage of the TPS76801 adjustable regulator is programmed using an external resistor divider as shown in Figure 27. The output voltage is calculated using: V O V ref 1 R1 R2 where: Vref = 1.1834 V typ (the internal reference voltage) (1) Resistors R1 and R2 should be chosen for approximately 50-A divider current. Lower value resistors can be used but offer no inherent advantage and waste more power. Higher values should be avoided as leakage currents at FB increase the output voltage error. The recommended design procedure is to choose R2 = 30.1 kto set the divider current at 50 A and then calculate R1 using: R1 V V O 1 ref R2 (2) OUTPUT VOLTAGE PROGRAMMING GUIDE TPS76801 VI 0.1 F IN PG PG 250 k 1.7 V 0.9 V OUTPUT VOLTAGE EN OUT VO R1 FB / NC GND R1 R2 UNIT 2.5 V 33.2 30.1 k 3.3 V 53.6 30.1 k 3.6 V 61.9 30.1 k 4.75 V 90.8 30.1 k R2 Figure 27. TPS76801 Adjustable LDO Regulator Programming POWER-GOOD INDICATOR The TPS768xxQ features a power-good (PG) output that can be used to monitor the status of the regulator. The internal comparator monitors the output voltage: when the output drops to between 92% and 98% of its nominal regulated value, the PG output transistor turns on, taking the signal low. The open-drain output requires a pullup resistor. If not used, it can be left floating. PG can be used to drive power-on reset circuitry or used as a low-battery indicator. PG does not assert itself when the regulated output voltage falls out of the specified 2% tolerance, but instead reports an output voltage low, relative to its nominal regulated value. 12 Submit Documentation Feedback TPS768xxQ www.ti.com SLVS211L - JUNE 1999 - REVISED JANUARY 2006 APPLICATION INFORMATION (continued) REGULATOR PROTECTION The TPS768xxQ PMOS-pass transistor has a built-in back diode that conducts reverse currents when the input voltage drops below the output voltage (for example, during power-down). Current is conducted from the output to the input and is not internally limited. When extended reverse voltage is anticipated, external limiting may be appropriate. The TPS768xxQ also features internal current limiting and thermal protection. During normal operation, the TPS768xxQ limits output current to approximately 1.7 A. When current limiting engages, the output voltage scales back linearly until the overcurrent condition ends. While current limiting is designed to prevent gross device failure, care should be taken not to exceed the power dissipation ratings of the package. If the temperature of the device exceeds +150C (typ), thermal-protection circuitry shuts it down. Once the device has cooled below +130C (typ), regulator operation resumes. POWER DISSIPATION AND JUNCTION TEMPERATURE Specified regulator operation is assured to a junction temperature of +125C; the maximum junction temperature should be restricted to +125C under normal operating conditions. This restriction limits the power dissipation the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits, calculate the maximum allowable dissipation, PDmax, and the actual dissipation, PD, which must be less than or equal to PDmax. The maximum-power-dissipation limit is determined using the following equation: T max T A P max J D R JA (3) Where: * TJmax is the maximum allowable junction temperature. * RJA is the thermal resistance junction-to-ambient for the package; that is, 172C/W for the 8-pin SOIC (D) and 32.6C/W for the 20-pin TSSOP (PWP) with no airflow. * TA is the ambient temperature. The regulator dissipation is calculated using: P D V V I I O O (4) Power dissipation resulting from quiescent current is negligible. Excessive power dissipation will trigger the thermal protection circuit. Submit Documentation Feedback 13 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) TPS76801QD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76801QDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76801QDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76801QDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76801QPWP ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76801QPWPG4 ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76801QPWPR ACTIVE HTSSOP PWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76801QPWPRG4 ACTIVE HTSSOP PWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76815QD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76815QDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76815QDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76815QDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76815QPWP ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76815QPWPG4 ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76815QPWPR ACTIVE HTSSOP PWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76815QPWPRG4 ACTIVE HTSSOP PWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76818QD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 17-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) TPS76818QDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76818QDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76818QDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76818QPWP ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76818QPWPG4 ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76818QPWPR ACTIVE HTSSOP PWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76818QPWPRG4 ACTIVE HTSSOP PWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76825QD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76825QDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76825QDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76825QDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76825QPWP ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76825QPWPG4 ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76825QPWPR ACTIVE HTSSOP PWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76825QPWPRG4 ACTIVE HTSSOP PWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76827QD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76827QDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76827QPWP ACTIVE HTSSOP PWP 20 TBD Call TI Call TI TPS76827QPWPG4 ACTIVE HTSSOP PWP 20 TBD Call TI Call TI Addendum-Page 2 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 17-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) TPS76828QD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76828QDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76830QD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76830QDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76830QPWP ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76830QPWPG4 ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76833QD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76833QDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76833QDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76833QDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76833QPWP ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76833QPWPG4 ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76833QPWPR ACTIVE HTSSOP PWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76833QPWPRG4 ACTIVE HTSSOP PWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76850QD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76850QDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76850QDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS76850QDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 3 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 17-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) TPS76850QPWP ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76850QPWPG4 ACTIVE HTSSOP PWP 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76850QPWPR ACTIVE HTSSOP PWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS76850QPWPRG4 ACTIVE HTSSOP PWP 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TPS76801, TPS76815, TPS76818, TPS76825, TPS76827, TPS76828, TPS76830, TPS76833, TPS76850 : * Automotive: TPS76801-Q1, TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1, TPS76828-Q1, TPS76830-Q1, TPS76833-Q1, TPS76850-Q1 Addendum-Page 4 PACKAGE OPTION ADDENDUM www.ti.com 17-Aug-2012 * Enhanced Product: TPS76801-EP, TPS76815-EP, TPS76818-EP, TPS76825-EP, TPS76833-EP, TPS76850-EP NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects * Enhanced Product - Supports Defense, Aerospace and Medical Applications Addendum-Page 5 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device TPS76801QDR Package Package Pins Type Drawing SOIC D SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 8 2500 330.0 12.4 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 6.4 5.2 2.1 8.0 12.0 Q1 TPS76801QDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS76801QPWPR HTSSOP PWP 20 2000 330.0 16.4 6.95 7.1 1.6 8.0 16.0 Q1 TPS76815QDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS76815QPWPR HTSSOP PWP 20 2000 330.0 16.4 6.95 7.1 1.6 8.0 16.0 Q1 TPS76818QDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS76818QPWPR HTSSOP PWP 20 2000 330.0 16.4 6.95 7.1 1.6 8.0 16.0 Q1 TPS76825QDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS76825QPWPR HTSSOP PWP 20 2000 330.0 16.4 6.95 7.1 1.6 8.0 16.0 Q1 TPS76833QDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS76833QPWPR HTSSOP PWP 20 2000 330.0 16.4 6.95 7.1 1.6 8.0 16.0 Q1 TPS76850QDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS76850QPWPR HTSSOP PWP 20 2000 330.0 16.4 6.95 7.1 1.6 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS76801QDR SOIC D 8 2500 367.0 367.0 35.0 TPS76801QDR SOIC D 8 2500 367.0 367.0 35.0 TPS76801QPWPR HTSSOP PWP 20 2000 367.0 367.0 38.0 TPS76815QDR SOIC D 8 2500 367.0 367.0 35.0 TPS76815QPWPR HTSSOP PWP 20 2000 367.0 367.0 38.0 TPS76818QDR SOIC D 8 2500 367.0 367.0 35.0 TPS76818QPWPR HTSSOP PWP 20 2000 367.0 367.0 38.0 TPS76825QDR SOIC D 8 2500 367.0 367.0 35.0 TPS76825QPWPR HTSSOP PWP 20 2000 367.0 367.0 38.0 TPS76833QDR SOIC D 8 2500 367.0 367.0 35.0 TPS76833QPWPR HTSSOP PWP 20 2000 367.0 367.0 38.0 TPS76850QDR SOIC D 8 2500 367.0 367.0 35.0 TPS76850QPWPR HTSSOP PWP 20 2000 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated