ALUMINUMELECTROLYTICCAPACITORS UZG 3.95mmL MAX. Chip Type, Wide Temperature Range Chip type with 3.95mmLMAX height. Operating over wide temperature range of - 40 to +105C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). AEC-Q200 compliant. Please contact us for details. UZT Smaller UZG Specifications Item Performance Characteristics Category Temperature Range -40 to +105C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 1 to 100F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes' application of rated voltage at 20C, leakage current is not more than 0.01 CV or 3 (A) , whichever is greater. 6.3 10 16 25 35 50 0.38 0.32 0.20 0.16 0.14 0.14 Rated voltage (V) 6.3 10 16 25 35 50 Impedance ratio Z-25C / Z+20C ZT / Z20 (MAX.) Z-40C / Z+20C 6 5 3 3 3 3 10 10 6 6 4 4 Rated voltage (V) Tangent of loss angle (tan ) tan (MAX.) Stability at Low Temperature Capacitance change tan Leakage current 120Hz 20C 120Hz Within 30% of the initial capacitance value 300% or less than the initial specified value Less than or equal to the initial specified value Endurance The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 1000 hours at 105C. Shelf Life After storing the capacitors under no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20C. Marking Black print on the case top. Chip Type Within 10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Type numbering system (Example : 16V 10F) 1 Positive Capacitance C0.2 MAX. Plastic0.3 platform 0.3 MAX. Capacitance 3.90 +0.05 -0.2 3.90 +0.05 -0.2 V 6.3 10 16 25 35 50 Code j A C E V H 0.5 MAX. 0.5 MAX. A0.3 E E A0.3 Series C0.2 B0.2 B0.2 Lot No. D0.5 D0.5 Series X2A2 10C 10C ZGZG Lot No.(C : 16V) Voltage 0.5 to 0.8 2 3 4 5 6 7 8 9 10 11 12 13 14 1 Z 2 G 3 1 4 C 5 1 6 0 7 0 8 M 9 C 10 11 13 B 14 U L 12 1 G U ZG 1 C 1 0 0 MC L 1 GB Positive Plastic platform A0.3 A0.3 Voltage (C : 16V) Voltage Capacitance change tan Leakage current D A B C E 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 (mm) 6.3 2.4 6.6 6.6 2.2 Taping code Configuration Taping code Configuration Capacitance tolerance (20%) Capacitance tolerance (20%) Rated capacitance (10F) RatedRated capacitance voltage(10F) (16V) Rated voltage (16V) Series name Negative Series name Type Negative 0.5 to 0.8 Type Dimensions 6.3 0J V Cap. (F) 1 2.2 3.3 4.7 10 22 33 47 100 Code 010 2R2 3R3 4R7 100 220 330 470 101 4 5 5 6.3 10 1A 19 26 32 52 5 5 6.3 16 1C 24 30 40 4 5 6.3 6.3 25 1E 16 26 35 44 4 5 6.3 6.3 35 1V 11 20 33 42 4 5 6.3 50 1H 13 22 36 4 4 4 5 6.3 Case size D (mm) 5.4 9.6 12. 16. 26. Rated ripple Rated ripple current (mArms) at 105C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 109 Taping specifications are given in page 23. Recommended land size soldering by reflow are given in page 18,19. Please refer to page 3 for the minimum order quantity. CAT.8100H