HDRA series
0.8 mm Pitch Connectors
Outline HDRA series connectors have been developed based on the HDR series
products for high speed signal interfaces such as SCSI-III, VHDCI and PCI.
Features
Principal
Applications
• Conforms to the United States ANSI/SFF8441 standards
• Provided with high performance EMI/ESD-shielded structure
• Mounted with locks or screws
• Low profile
• Sequence structure
type personal computers and their peripheral
equipment, and mobile equipment
Electrical
Characteristics
Rated voltage 30V AC (r.m.s.)
Rated current 0.3 A
Insulation resistance Over 500 megohms at 100V DC
Dielectric withstanding voltage 250V AC (r.m.s.)
Contact resistance
70 milliohms or less
(for combination of MA or MA1 and LFDT)
100 milliohms or less
(for combination with MA1 and W1LFDT)
Server, Router, Notebook
mm Pitch
0.8
Connectors
Document Disclaimer
When placing orders with us, minimum order quantities are set for every product.
Be sure to contact us before starting preliminary design of PCBs using our connectors.
The specifications and information shown in the catalog are subject to change without notice.
Reflow temperature profile
(for reference purposes)
Flow temperature profile
(for reference purposes)
The reflow temperature profile shown in this drawing is for reference
purposes. This profile depends on requirements such as reflow
equipment, soldering paste, and PCB size. Thus, this profile may not
meet with your specific situation. Please evaluate your PCB-mounting
soldering and set your own reflow temperature profile.
ΩApplicable products
The profile shown in this drawing is applicable only for those products shown above.
The flow temperature profile as shown above is for reference
purposes. This profile depends on requirements such as the PCB size.
Thus, this profile may not meet with your specific situation. Please
evaluate your PCB-mounting soldering and set your own flow
temperature profile.
ΩApplicable products
The profile shown in this drawing is applicable only for those products shown above.
HDRA series SMT type for PCB HDRA series through hole type for PCB
100~130˚C
260±5˚C
30~60sec
5sec
150~180˚C
220˚C
250˚C
(Full heating
period)
30~60sec
(Preheating period)
90~120sec
(Peak)
0.8mm pitch connector
For cable
IDC
ANSI/SFF8441
IDC type male connector for cable
HDRA-E36MA+
Mating connector: HDRA series right-angle through hole type or straddle SMT type female connector
For use with housings: HDRA series upright housing, HDRA-E36LPTH
Required tool: Termination tool: FHAT-0029, IDC tool: FHPT-923B, Hand presser: MFC-K1 (Refer to page Tool-10)
● Components
➀ Contacts
➁ Insulator
➂ Shell
➃ Spacer
➄ Cable housing
0.8
6.48
7.1
14.7
0.8≈17=13.6
19.16
21.71
POS.#18
POS.#18
POS.#1
POS.#19
POS.#19
POS.#1
POS.#36
POS.#36
25˚
➁
➃
➂
➀
➄
●Configuration of product Part No.
HDRA-E36M A+
➀➁➂➃
➀Series name
➁No. of contacts: 36
➂Type of contact
M: IDC type, male
➃Compatible cable
A: AWG#30(7/0.1),dia. 0.58 mm
3.75
Others
Wire
wrapping
CrimpingSolderingIDCPress-inSMT
Through
hole
0.8mm pitch connector
For cable
IDC
ANSI/SFF8441
IDC type male connector for cable
HDRA-E68MA+
● Components
➀ Contacts
➁ Insulator
➂ Shell
➃ Spacer
➄ Cable housing
POS.#34
POS.#68
POS.#68
POS.#35
POS.#35
POS.#1
POS.#34
POS.#1 0.8≈33=26.4
0.8
32.6
34.5
14.7
75.4
31.95
➂
➁
➀
➄
➃
Mating connector: HDRA series right-angle through hole type or straddle SMT type female connector
For use with housings: HDRA series upright housing, HDRA-E68LGKPA
Required tool: Termination tool: FHAT-0029, IDC tool: FHPT-923B, Hand presser: MFC-K1 (Refer to page Tool-10)
●Configuration of product Part No.
HDRA-E68M A+
➀➁➂➃
➀Series name
➁No. of contacts: 68
➂Type of contact
M: IDC type, male
➃Compatible cable
A: AWG#30 (7/0.1), dia. 0.58 mm
3.75
25˚
Others Wire
wrapping Crimping Soldering IDC Press-in SMT Through
hole
HDRA-E68M ( ) 1+
➀➁➂➃
➄
➀Series name
➁No. of contacts: 68
➂Type of contact
M: IDC type, male
➃Compatible cable
Blank: AWG#30 (1/0.254), dia. 0.58 mm
A : AWG#30 (7/0.1), dia. 0.58 mm
C : AWG#34 (7/0.064), dia. 0.44 mm
➄IDC method
1: One side IDC
● Components
➀ Contacts
➁ Insulator
➂ Shell
➃ Cable housing
68
34
21.2
POS.#1
POS.#34
POS.#68 POS.#35
0.8≈33=26.4
31.95
4.84
2.18
0.8
➃
➁
➂
➀
1
35
POS.#1
POS.#34
POS.#35
POS.#68
0.8mm pitch connector
For cable
IDC
ANSI/SFF8441
IDC type male connector for cable
HDRA-E68M( )1+
Mating connector: HDRA series right-angle through hole type or straddle SMT type female connector
For use with housings: HDRA series vertical housing, HDRA-E68LGKP ( )
Required tool: Termination tool: FHAT-0027, IDC tool: FLPT-0021A, Hand presser: RPS-K4 (Refer to page Tool-10)
●Configuration of product Part No.
25˚
Others
Wire
wrapping
CrimpingSolderingIDCPress-inSMT
Through
hole
0.8 mm pitch connector
For cable
IDC
IDC type male connector for cable
HDRA-E100M( )1+
Mating connector: HDRA series right-angle through hole type female connector
●Configuration of product Part No.
HDRA- E 100 M ( ) 1+
➀➁➂➃
➀Series name
➁No. of contacts: 100
➂Type of contact
M: IDC type, male
➃Compatible cable
Blank: AWG#30 (1/0.254), dia. 0.58 mm
A : AWG#30 (7/0.1), dia. 0.58 mm
ANSI/SFF8441
➂
➀
➁
POS.#100
POS.#100
POS.#50
POS.#50
POS.#1
POS.#1
POS.#51
POS.#51
21.2
4.84
2.18
0.8 7
44.2
42.4
47.95
➀Contacts
➁Insulator
➂Shell
➃Cable housing
➃
● Components
For use with housings: HDRA series vertical housing, HDRA-E100LPA, HDRA-E100LPW( )
Required tool: Termination tool: FHAT-0038A, IDC tool: FLPT-0021A, Hand presser: RPS-K4 (Refer to page Tool-10)
Others Wire
wrapping Crimping Soldering IDC Press-in SMT Through
hole
● Configuration of product Part No.
➀ Series name
➁ No. of contacts: 68
➂ Form of contact
FD: Straight, DIP type, female
➃ With ground lock pin
➄ Lock screw
SLD: Provided
Blank: None
Straight DIP type female connector for PCBs
HDRA-EC68FDT-( )+
Mating connector: HDRA series male connectors
➀➁➃➄
➂
34 1
3568
0.8≈33=26.4
42.7
37.7
31.65
28.3
0.8
Pos.#68
Pos.#2
Pos.#1
3.46
5
M2≈0.4
7.4
¡™
£
2.3
0.3
7.5
1.55
2.975
2.28
Ø2.25±0.1
Ø1±0.05
68-Ø0.65±0.05
Ø1.2±0.05
Ø1.75±0.05 (T.H)
(P.T.H)
1.15±0.05
1.15±0.05
1.96±0.05
1.175±0.05
30±0.1
26.4±0.1
2.975±0.05
1.6±0.03
0.8±0.03
32.35±0.1
8.4
2.975±0.05
2.88
3.26
Pos.#34
Pos.#35
Pos.#33
Pos.#1
Pos.#68
(Pad)
(Pad)
¢
∞
32.35
30
26.4
0.8
5.55.2
0.3
05Z
34.7
2.4
4.88
37.7
R
● Components
➀
➁
➂
➃
➄
Insulator
Contact
Shell
Sqr.nut
Hold down
Recommended PCB layout
Recommended panel cut-out dimensions
HDRA series
SMTDip Press-in IDC Soldering Crimping Others
Wire
wrapping
0.8 mm pitch connector
For PCBs
Straight DIP
EMI-filtered countermeasures
HDRA- EC 68 FD T- ( )+
100-Ø0.65±0.05
Ø1±0.05
Ø2.25±0.1 Ø1.2±0.05
Ø1.75±0.05 (T.H)
(P.T.H)
¡™
£
¢
∞
(96 Plc.)
(48 Plc.)
0.8±0.03
1.6±0.03
4±0.03
1.15±0.05
1.15±0.05
1.96±0.05
42.4±0.1
46±0.1
48.35±0.1
48.35
46
58.7
50.7±0.1
2.4±0.08
4.88±0.08
53.7±0.1
53.7
47.65
42.4
0.8 (48Plc.)
42.4
4
1.6
0.8
5.55.2
Pos.#50
Pos.#100 Pos.#51
Pos.#1
4
50
100
1
51
3.46
5
M2≈0.4
R1.2 Ref.
2.3
0.3
7.5
8.4
2.975±0.05
7.4
1.55
2.975
2.28
0.3
2.88
3.26
Pos.#50 Pos.#25
Pos.#51
Pos.#1
Pos.#100
Pos.#26
Recommended PCB layout
Recommended panel cut-out dimensions
(Pad)
(Pad)
Straight DIP type female connector for PCBs
HDRA-EC100FDT-( )+
➀ Series name
➁ No. of contacts: 100
➂ Form of contact
FD: Straight, DIP type, female
➃ With ground lock pin
➄ Lock screw
SLD: Provided
Blank: None
● Configuration of product Part No.
➀➁➂➃➄
Mating connector: HDRA series, male connector
● Components
➀
➁
➂
➃
➄
Insulator
Contact
Shell
Sqr.nut
Hold down
HDRA series
Wire
wrapping
Others Crimping Soldering IDC Press-in DipSMT
0.8 mm pitch connector
For PCBs
Straight DIP
EMI-filtered countermeasures
HDRA- EC 100 FD T- ( )+
0.8 mm pitch connector
For PCB
Right-angle Through hole
Right-angle through hole type female connector for PCB
HDRA-EC68LFDT( )-( )+
Mating connector: HDRA series IDC type male cable connector, or straddle SMT type male connector
●Configuration of product Part No.
HDRA- EC 68 LFD T ( )- ( )+
➀➁ ➄➂➃ ➅
ANSI/SFF8441
4.88±0.08
2.4±0.08
37.7±0.1
➂
➀
➁
➃
➄
34.7≠0.1
POS.#2
POS.#1
➅
–0
R
3.925
5.3
1.55
26.8
42.7
37.7
28.3
31.65
0.4
14.7
9.5
HDRA LFD
0.8≈33=26.4
0.8
0.3
0.8 32.35
41.9
3.46
34
68
1
35
0.3
1.15
1.15
1.2
C
3.5
A
6B
41.9±0.05
1.15±0.03
1.15±0.03
32.35±0.05
4.775 REF.
(P.T.H
.)
(P.T.H.)
Recommended PCB layout
t=1.6mm
POS.#1
POS.#2
68-ø0.65
PAD ø1±0.1
2-ø1.75
2-ø1.2
PAD ø2.25±0.1
±0.08
±0.05
±0.05
0.4±0.03
26.8±0.05
2.25±0.05
2.625±0.05
6.3MAX.
POS.#68
4.3±0.1
3.4±0.1
4.9±0.1
1.6±0.03
0.8±0.03
2.775
➀Contacts
➁Brackets
➂Insulator
➃Hold downs
➄Shell
➅Lock screws
Recommended panel cut-out dimensions
● Components
Edge of PCB
: PAD
±0.05
(Two lock screws are supplied with a connector.)
1.2±0.03
➅
➀Series name
No. of contacts: 68
Type of contact
LFD:
Right-angle through hole type, female
With board lock pin
Length of contact, board lock pins or location peg
Blank: A-2.08 mm contacts
: B-2.28 mm board lock pins
: C-3.7 mm location peg
➁
➂
➄
S : A-2.08 mm contacts
B-2.28 mm board lock pins
C-2.3 mm location peg
2 : A-2.08 mm contacts
B-2.28 mm board lock pins
C-1.4 mm location peg
Lock screws
Blank : None
SL : provided (Thickness of panel: 1.12 mm)
➃
Select the connector according to panel thickness.
For the application without panel, use washers or
special lock screw (P/N: HDRA-E68LFD-7C).
Others Wire
wrapping Crimping Soldering IDC Press-in SMT Through
hole
0.8mm pitch connector
For PCB
Right-angle Through hole
EMI shielded
Right-angle through hole type female connector for PCB
HDRA-EC100LFDT( )-( )+
Mating connector: HDRA series male connector
● Components
➀ Bracket
➁ Contacts
➂ Insulator
➃ Shell
➄ Hold downs
●Configuration of product Part No.
HDRA- EC 100 LFD T ( )- ( )+
➀➁➂➃➅➄
➀Series name
No. of contacts: 100
Type of contact
LFD: Right-angle through hole type,
female
With ground contact
Through hole length
Blank : 2.08 mm
1 : 3.4 mm (under planning)
➅Lock screw
Blank: None
SL : Provided
(Panel thickness: 1.12 mm)
GP : Guide pin
➁
➂
➃
➄
Select the connector according to panel thickness.
For the application without panel, use washers or
special lock screw (P/N: HDRA-E68LFD-7C).
∞
£
¡
™
¢
HDRA LFD
58.7
53.7
47.65
48.35
57.9
44.3
42.4
0.8≈24=19.2 0.8≈24=19.2
5.2 9.5
POS.#50 POS.#1
POS.#51
POS.#100
0.8
M2≈0.4
0.3≈0.3
21.1 21.1
1
51
50
100
1.55
3.925
3.7
3.5
6
1.6±0.03
0.8±0.03
0.8≈24=19.2±0.05
21.4
(PAD)
21.4
POS.#2
POS.#1
POS.#51
POS.#50
POS.#100
2.25±0.05
2.625±0.05
1.15±0.05
1.15±0.05
1.2±0.05
0.4±0.03
42.8±0.1
Edge of PCB 0.8±0.03
1.6±0.03
0.8≈24=19.2±0.05
48.35±0.1
57.9±0.1
4.78±0.1
6.3MAX.
4.9
ø1±0.05
(PAD)
ø2.25±0.1
2-ø1.75±0.08
100-ø0.65±0.05 ø1.2+0.05(P.T.H)
0.4+0.03
4.3
3.4
Recommended PCB layout
t=1.6mm
: PAD
Others
Wire
wrapping
CrimpingSolderingIDCPress-inSMT
Through
hole
0.8mm pitch connector
For PCB
Right-angle Through hole
ANSI/SFF8441
Right-angle through hole type female connector for PCB
HDRA-EA36LFDT-( )+
●Configuration of product Part No.
HDRA-EA 36LFD T-( )+
➀➁➂➃➄
➀Series name
➁No. of contacts: 36
➂Type of contact
LFD: Right-angle through hole type, female
➃Provided with board lock mechanism
➄Lock screw
Blank: None
SL : Provided (Thickness of panel: 1.12 mm)
Mating connector: HDRA series IDC type male cable connector
Note●Jack screw is not available at present.
➁
➄
➃
➂
➀
➅
POS.#36
POS.#2
POS.#1
1.6
0.8
14.7
9.5
0.4
HDRA LFD
24.9
29.9
21.9
5.3
1.6
0.3
1.15
1.2
1.15
24.9
18.86
0.8≈17=13.6
0.8
3.46
R
4.88±0.08
2.4±0.08
2.08
2.28 5
2.775
Edge of PCB
(Two lock screws are supplied with a connector.)
2.25
6.3MAX.
19.55
1.15
1.15
0.4
0.8
36-ø0.65±0.05
2-ø1.2±0.05
POS
(P.T.H.)
(P.T.H.) .#2
POS.#36
POS.#1
PADø1±0.1
PADø2.25±0.1
● Components
➀ Bracket
➁ Contacts
➂ Insulator
➃ Shell
➄ Square nuts
➅ Lock screw
➆
➆
Board lock pin
Recommended PCB layout
t=1.6mm
Recommended panel cut-out dimensions
1.2±0.03
≠0.1
–0
±0.1
25˚
±0.03
±0.03
±0.03
±0.05
±0.05
±0.05
±0.03 ±0.03
Select the connector according to panel thickness.
For the application without panel, use washers or
special lock screw (P/N: HDRA-E68LFD-7C).
Others Wire
wrapping Crimping Soldering IDC Press-in SMT Through
hole
0.8mm pitch connector
For PCB
Right-angle Through hole
ANSI/SFF8441
Right-angle through hole type female connector for PCB
HDRA-E68W( )LFDT1EC-( )+
●Configuration of product Part No.
HDRA-E68W ( ) LFD T1 E C -( )+
➀➁
➂➃➄➅➆➇➈
➀Series name
➁No. of contacts: 136 (68≈2)
➂No. of stacks: 2
➃
Length of contact,
through hole
1: 2.08 (PCB: 1.6 mm thick)
2: 3.4 (PCB: 2.4 mm thick)
➄Type of contact
LFD: Right-angle through hole type,
female
➅Earth lock pin (provided with
board lock mechanism)
➆Provided with shell connection
reinforcement
➇Provided with protection cover
for contacts and bends
➈Lock screw
Blank: None
SL :
Provided (Thickness of panel: 1.12 mm)
Mating connector: HDRA series IDC type male cable connector, or straddle SMT type male connector
JAPAN
HONDA
➈
➂
➄
➃
➅
➀
➁
➇➆
42.7
37.7
31.65
28.3
0.8≈33=26.1
32.35
2.02 2.02
37.7±0.1
34.7
10.72
2.4±0.08
5.84±0.05
POS.#2
POS.#68
POS.#68
(CN1)
(CN1)
(CN1)
(CN2)
(CN2)
POS.#1
POS. #1
POS. #2
(CN2)
5.84
R
3.46
0.3
5.08
1.15
1.15
1.15
1.2
1.15
5.3
1.2
3.5
11.84
2.28
2.08
● Components
➀ Bracket
➁ Contacts
➂ Insulator
➃ Shell
➄ Square nuts
➅ Lock screw
➆ Board lock pin
➇ Shell connector
➈ Protection covers
Recommended panel cut-out dimensions
Recommended PCB layout
t=1.6mm or 2.4mm
Edge of PCB
(CN1)
(CN2)
POS.#1
POS.#68
1.2
1.151.15
1.15
5.08
1.15
6.3MAX 2.25
32.35
6-ø1.2
PAD ø1
PAD ø2.25
POS.
#
1(CN2)
POS.
#
2(CN2)
2.02 2.98
0.8≈33=26.4
2.78
1.6
1.6 POS.#67(CN1)
136-ø0.65
POS.#68(CN1)
0.4
0.8
±0.03 ±0.03
±0.03
±0.03
±0.05
±0.05
±0.1
±0.1
±0.03 ±0.03
±0.03
±0.05 ±0.1
±0.05
±0.05
0.8≈33=26.4
(P.T.H.)
(P.T.H.)
25˚
(Four lock screws are supplied with a connector.)
±0.05
±0.03 ±0.03
±0.03
±0.03
±0.03
19.1
18.1
5.2
1.2±0.03
Select the connector according to panel
thickness. For the application without
panel, use washers or special lock
screw (P/N: HDRA-E68LFD-7C).
≠0.1
–0
≠0.1
–0
Others
Wire
wrapping
CrimpingSolderingIDCPress-inSMT
Through
hole
0.8 mm pitch connector
For PCB
Right-angle Through hole
Right-angle through hole type female connector for PCB
HDRA-E100W( )LFDT1EC-( )+
Mating connector: HDRA series IDC type male connector
●Configuration of product Part No.
HDRA- E 100 W ( ) LFD T1 E C- ( )+
➀➁ ➄➂➃ ➅➆➇ ➈
➀Series name
➁No. of contacts: 100
➂W: Double stacked connector
➅Earth lock pin (provided with
➆
board lock mechanism)
➇
Provided with shell connection
reinforcement
Provided with protection cover
for contacts and bends
➄Type of contact
LFD:
Right-angle through hole type, female
➃
Length of contacts or board lock pins
1: A-2.08 mm contacts
B-2.28 board lock pins
2: A-3.4 mm contacts
B-3.6 mm board lock pins ➈Lock screws
Blank: None
SL :
provided (Thickness of panel: 1.12 mm)
ANSI/SFF8441
➂
➀➁
➃
➄
50.7±0.1
2.25
6.3MAX.
POS.#1(CN1)
POS.#100(CN2)
POS.#2(CN1)
POS.#50(CN2)
POS.#51(CN1) POS.#100(CN1)
POS.#50(CN1)
POS.#1(CN2)
POS.#2(CN2)
POS.#51(CN2)
1.15±0.05
1.15±0.05
1.2±0.05
1.15±0.05
1.15±0.05
1.2±0.05
5.08±0.05
0.8±0.03
1.6±0.03
0.8±0.03
2.02±0.05
1.6±0.03
6-ø1.2±0.05(P.T.H.)
42.4±0.05
48.36±0.05
52.7
2.4±0.08
10.72±0.1
5.84±0.05
53.7±0.1
58.7
53.7
47.65
42.4
24.3
5.45.2
19.2
19.2
0.8
POS.#1
5.84
POS.#2
POS.#99 POS.#100
POS.#1
POS.#100
3.46
0.3
21.1
0.8≈24=19.2
2.02 2.02
21.1
48.36
R
5.3±0.15
1.15
1.15
1.15
0.3
5.08
1.15
1.2 1.2
3.5
11.84
13±0.3
A
B
19.2±0.05 19.2±0.05
(P.T.H.)
200-ø0.65±0.05
(4)
Recommended panel cut-out dimensions
Edge of PCB
➇
➉
0.8≈24=19.2
(CN1)
(CN2)
(CN1) (CN1)
(CN2)
(CN2)
➈
➀Contacts
➁Brackets
➂Insulator A
➃Board lock pin
➄Square nuts
➅Lock screws
➆Shell
➇Insulator B
➈Shell connection
➉Protection covers
Recommended PCB layout
t=1.6mm or 2.4mm
● Components
: PAD
➅
➆(Four lock screws are applied with connector.)
Select the connector according to panel
thickness. For the application without
panel, use washers or special lock
screw (P/N: HDRA-E68LFD-7C).
±0.05
Others Wire
wrapping Crimping Soldering IDC Press-in SMT Through
hole
0.8mm pitch connector
Vertical housing
EMI shielded
ANSI/SFF8441
EMI-shielded vertical plastic housing for standard cable
HDRA-E68LGKP( )
●Configuration of product Part No.
For use with connectors : HDR series IDC type cable connector : -LGKPA for MA, -LGKPC/-LGKPE for MA1, and -LGKPF for MC1
Required tools (for LGKPC, LGKPE and LGKPF): Clamp caulking tools: FLPT-0017B (Refer to page Tool-10)
Ultrasonic welder, Housing holding jig, Sonic welder
● Components
➀ Cover
➁ Inner shell A
➂ Inner shell B
➃ Cable clamp
➄ Screw
➅ Bushing
➆ Thumb screw
➇ Cap (plastic)
● Components
➀ Cover A
➁ Cover B
➂ Shell A
➃ Shell B
➄ Thumb screw
➅ Cap (plastic)
Part No.A B
9.5
7.5
7.2
C
10.5≈9.5
10.5
HONDA JAPAN
JAPAN
12
➅➄
➃
➁
➂
➀
➇
➆
➅
➄
➃
➁➂
➀
ø10MAX
5.8
1218.3
11.5
4
42.7
37.7
2-M2≈0.4
13≈9.5
28.4
8
A
7.35 1.81 33.69B
2.68
37.7
42.7
C
36.44
2-M2≈0.4
HDRA-E68LGKPA
HDRA-E68LGKPC,LGKPE,LGKPF
The following figure shows HDRA-E68LGKPF.
11.5
9.5
9
HDRA-E68LGKPC
HDRA-E68LGKPE
HDRA-E68LGKPF
HDRA-E ( )68 LGKP
➀➁ ➂
➀Series name
➁No. of contacts: 68
➂A: Vertical cable holding type
C: Vertical ultrasonic welding type
E: Vertical ultrasonic welding type
F: Vertical ultrasonic welding type
Outside diameter of cable is shown in the dimension table.
5.81
Thumb screw with
plastic cap should be
tightened by hand. For
screw driver assembly
use the product (P/N:
HDRA-E68LGKPE3)
with metal thumb
screws attached.
Others Wire
wrapping Crimping Soldering IDC Press-in SMT Through
hole
0.8 mm pitch connector
Housing
Vertical
EMI-filtered vertical metallic housing
HDRA-E100LPW( )
●Configuration of product Part No.
HDRA- E 100 LP W ( )
➀➁ ➃➂
➀Series name
➁No. of contacts: 100
➂Type of housing: Ver tical type
➃Compatible cable and form of through hole
B: Two holes are available for two cables. Outside diameters of cable are 6.9 mm
C: One hole is available for one cable. Outside diameter of cable is 9.6 mm
EMI filtered
➂
➀
➁
58.72.78
7.45
9
53.7
54.44
46.44
24.44
HONDA JAPAN
12
10.3
HDRA-E100LPWC
HDRA-E100LPWB
8.3
7.6
7.6
¡Housing A
™Housing B
£Lock screws
● Components
For use with connectors: HDRA-E100M( )1+
Others Wire
wrapping Crimping Soldering IDC Press-in SMT Through
hole
0.8mm pitch connector
Vertical housing
EMI shielded
ANSI/SFF8441
EMI-shielded vertical plastic housing
HDRA-E36LPTH
For use with connectors: HDRA-E36M( )+
Mating connectors: HDRA -EA36LFDT+ +
+
Lock screw (HDR-E14LMY-SL-02C) panel:0.5-0.8mm thick
-EA36FT-NS+ Lock screw (HDR-E14LMY-SL-02C) panel:0.5-0.8mm thick
Required tools: Clamp caulking tools: FLPT-0024A (Refer to page Tool-10) Ultrasonic welder, Housing holding jig, Sonic welder
●Configuration of product Part No.
● Components
➀
➁
➂
➃
➄
➅
➁
➄
➃
➂
➀
➅
HDRA-E 36LPTH
➀➁➂
➀Series name
➁No. of contacts: 36
➂Type of housing: Ver tical type
Case A
Case B
Inner shell A
Inner shell B
Lock spring A
Lock spring B
ø6.5
1.1
10
9.5
14MAX.
31
35
31≠0.3
–0.15
Others
Wire
wrapping
CrimpingSolderingIDCPress-inSMT
Through
hole
