FOR MESSRS : DATE : Nov.12,2010
CUSTOMER’S ACCEPTANCE SPECIFICATIONS
TX14D11VM1CAB
C O N T E N T S
No. ITEM SHEET No. PAGE
1 COVER 7B64PS 2701-TX14D11VM1CAB-4 1-1/1
2 RECORD OF REVISION 7B64PS 2702-TX14D11VM1CAB-4 2-1/2~2/2
3 GENERAL DATA 7B64PS 2703-TX14D11VM1CAB-4 3-1/1
4 ABSOLUTE MAXIMUM RATINGS 7B64PS 2704-TX14D11VM1CAB-4 4-1/1
5 ELECTRICAL CHARACTERISTICS 7B64PS 2705-TX14D11VM1CAB-4 5-1/3~3/3
6 OPTICAL CHARACTERISTICS 7B64PS 2706-TX14D11VM1CAB-4 6-1/3~3/3
7 BLOCK DIAGRAM 7B64PS 2707-TX14D11VM1CAB-4 7-1/1
8 INTERFACE TIMING CHART 7B64PS 2708-TX14D11VM1CAB-4 8-1/5~5/5
9 DIMENSIONAL OUTLINE 7B63PS 2709-TX14D11VM1CAB-4 9-1/2~9-2/2
10 APPEARANCE STANDARD 7B64PS 2710-TX14D11VM1CAB-4 10-1/5~5/5
11 PRECAUTION IN DESIGN 7B64PS 2711-TX14D11VM1CAB-4 11-1/3~3/3
12 DESIGNATION OF LOT MARK 7B64PS 2712-TX14D11VM1CAB-4 12-1/1
13 PRECAUTION FOR USE 7B64PS 2713-TX14D11VM1CAB-4 13-1/1
*When product will be discontinued, customer will be informed by HITACHI with twelve
months prior to discontinuation.
ACCEPTED BY; PROPOSED BY;
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD
P.O. BOX 26-27
2,13TH EAST ST. K.E.P.Z.
KAOHSIUNG TAIWAN R.O.C.
TEL:(07) 821-5811(7 LINE)
FAX:(07) 821-5815
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. Sh.
No. 7B64PS 2701-TX14D11VM1CAB-4 PAGE 1-1/1
RECORD OF REVISION
DATE SHEET No. SUMMARY
Jun.02,’06 7B64PS 2704-
TX14D11VM1CAB-2
PAGE 4-2/2
4.2 ENVIRONMENTAL ABSOLUTE MAXIMUM RATINGS
Delete :
Note 13 : Operation Temperature of Touch Panel is -5℃ ~ 60℃
None – operation Temperature of Touch Panel is -20℃ ~ 70℃
7B64PS 2705-
TX14D11VM1CAB-3
PAGE 5-1/3
5.2.3 MECHANICAL CHARACTERISTICS
Changed:
7B64PS 2708-
TX14D11VM1CAB-3
PAGE 8-5/5
8.5 INTERNAL PIN CONNECTION
Changed :
CN1 JAE : FA5B040HF1(Sn plating) FA5B040HP1R3000(Au plating)
7B64PS 2709-
TX14D11VM1CAB-3
PAGE 9-2/2
9. DIMENSIONAL OUTLINE
The lot label size and position is changed.
May.13,’08
7B64PS 2712-
TX14D11VM1CAB-3
PAGE 12-1/1
12.1 LOT MARK
Changed : 5 digits for production number
↓
6 digits for production number
12.3 LOCATION OF LOT MARK
Changed :
12.4 REVISION(Rev.) CONTROL
Added : Rev. B CN1 JAE : FA5B040HP1R3000
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2702-TX14D11VM1CAB-4 PAGE 2-1/2
Sh.
No.
ITEM SPECIFICATION NOTE
Pen Input Pressure 0.1~0.8N R0.8, Polyacetal Pen
Finger 0.1~1.0N R8, Silicon Rubber
↓
ITEM SPECIFICATION NOTE
Pen Input Pressure 1.2N max. R0.8, Polyacetal Pen
Finger 1.2N max. R8, Silicon Rubber
↓
RECORD OF REVISION
DATE SHEET No. SUMMARY
Nov.12,’10 7B64PS 2710-
TX14D11VM1CAB-4
PAGE 10-5/5
10.3 APPEARANCE SPECIFICATION
Changed : Blistering Puffiness 0.4mm max. → 0.6mm max.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2702-TX14D11VM1CAB-4 PAGE 2-2/2
Sh.
No.
3.GENERAL DATA
(1) Part Name TX14D11VM1CAB
(2) Module Dimensions 167.0(W)mm x 109.0(H)mm x (10.9)(D)mm max.
(3) LCD Active Area 115.2(W)mm x 86.4(H)mm
(4) Dot Pitch 0.12(W)mm x 3(R,G,B)(W) x 0.36(H)mm
(5) Resolution 320x3(R,G,B)(W)x240(H) dots
(6) Color Pixel Arrangement R,G,B Vertical stripe
(7) LCD Type Transmissive Color TFT LCD (Normally White)
(8) Display Type Active Matrix
(9) Number of Colors 262k Colors (R,G,B 6bit parallel)
(10) Backlight Cold Cathode Fluorescent Tube (U type CFL) x 1
(11) Weight (220)g
(12) Interface 40pin (C-MOS)
(13) Power Supply Voltage 3.3V only (Include Timing Controller and Power Unit)
(14) View Direction 6 O’clock
(15) Touch Panel Resistance type
The surface is antiglare type
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2703-TX14D11VM1CAB-4 PAGE 3-1/1
Sh.
No.
4. ABSOLUTE MAXIMUM RATINGS
4.1 ELECTRICAL ABSOLUTE MAXIMUM RATINGS OF LCD VSS=0V
ITEM SYMBOL MIN. MAX. UNIT COMMENT
Power Supply for Logic VDD -0.3 4.0 V
Input Voltage VI -0.2 VDD+0.2 (Note 1)
Input Current Ii 0 1 A
VESD0 - ±100 V (Note 2,3)
Static Electricity VESD1 - ±8 kV (Note 2,4)
Note 1 : DTMG,DCLK,RD0~RD5,GD0~GD5,BD0~BD5.
Note 2 : 200pF-250Ω 25℃ - 70%RH
Note 3 : Interface Pin Connector.
Note 4 : The surface of metal bezel and LCD panel .
4.2 ENVIRONMENTAL ABSOLUTE MAXIMUM RATINGS
OPERATING STORAGE
I T E M MIN. MAX. MIN. MAX. COMMENT
Temperature (-20) (70) (-30) (80) (Note 2,3,6,7,8,10,12,13)
Humidity (Note 1) (Note 1) Without condensation
Vibration -
4.9m/s2
(0.5G) - 19.6m/s2
(2G)
(Note 5) (Note 4)
Shock -
29.4m/s2
(3G) - 490m/s2
(50G)
(Note 5)
XYZ directions
(Note 9)
Corrosive Gas Not Acceptable Not Acceptable
CFL Life Time 50,000 h
(Average) (Note 11) - at 25℃ , IL=4.0mA max.
Note 1 : Ta≦40℃ : 85%RH max.
Ta＞40℃ : Absolute humidity must be lower than the humidity of 85%RH at 40℃.
Note 2 : For storage condition Ta at -30℃ ＜ 48h , at 80℃ ＜ 100h.
For operating condition Ta at -20℃ ＜ 100h
Note 3 : Background color changes slightly depending on ambient temperature.
This phenomenon is reversible.
Note 4 : 5Hz~100Hz(Except resonance frequency)
Note 5 : This LCM will resume normal operation after finishing the test.
Note 6 : The response time will be slower at low temperature.
Note 7 : Only operation is guarantied at operating temperature. Contrast, response time,
another display quality are evaluated at +25℃.
Note 8 : When LCM is operated over 60℃ ambient temperature , the ICFL of LCM should
be adjusted to 3mA max.
Note 9 : Pulse Width : 10ms
Note 10 : This is panel surface temperature , not ambient temperature.
Note 11 : When brightness reached 50% of initial brightness.
Note 12 : When LCM be operated less than 0℃ , the life time of CFL will be reduced .
The rise time of CFL ON will be longer when the ambient temperature below 0℃
and confirming the characteristics of inverter is necessary .
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2704-TX14D11VM1CAB-4 PAGE 4-1/1
Sh.
No.
5. ELECTRICAL CHARACTERISTICS
5.1 ELECTRICAL CHARACTERISTICS OF LCD Ta=25℃,VSS=0V
I T E M SYMBOL CONDITION MIN. TYP. MAX. UNIT
Power Supply Voltage VDD - 3.0 3.3 3.6 V
“H” level 2.0 - VDD Input Voltage for Logic
(Note 1) VI “L” level VSS - 0.8 V
Power Supply Current
(Note 2) IDD VDD-VSS=3.3V - (150) - mA
Vsync Frequency fV - 52 60 68 Hz
Hsync Frequency fH - 13.1 15.2 17.7 kHz
DCLK Frequency fCLK - 4.85 5.85 (7.0) MHz
Note 1 : DTMG,DCLK, RD0~RD5,GD0~GD5,BD0~BD5.
Note 2 : f V=60Hz,Ta=25℃, Pattern used as display pattern : All Black.
Note 3 : Need to make sure of flickering and rippling of display when setting
the frame frequency in your set.
5.2 ELECTRICAL CHARACTERISTICS OF TOUCH PANEL
5.2.1 OPERATING CONDITION
ITEM SPECIFICATION
Operating Voltage 5VDC max.
5.2.2 ELECTRICAL CHARACTERISTICS
ITEM SPECIFICATION NOTE
XR-XL 210~640Ω Resistance
Between Terminal YT-YB 240~680Ω
Insulation Resistance X-Y 20MΩmin. Operating Voltage : 25V DC
X 1.5% max.
Linearity Y 1.5% max.
(Note 1)
Chattering 10ms max.
5.2.3 MECHANICAL CHARACTERISTICS
ITEM SPECIFICATION NOTE
Pen Input Pressure 1.2N max. R0.8, Polyacetal Pen
Finger 1.2N max. R8, Silicon Rubber
Surface Hardness 2H min.
5.2.4 OPTICAL CHARASTERISTICS
ITEM SPECIFICATION NOTE
Transparency 76% min
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2705-TX14D11VM1CAB-4 PAGE 5-1/3
Sh.
No.
5.3 ELECTRICAL CHARACTERISTICS OF BACKLIGHT
ITEM SYMBOL MIN. TYP. MAX. UNIT NOTE
Lamp Voltage VL - 760 - Vrms Ta=25℃
Frequency fL - 55 - kHz
Lamp Current (1Lamp)(Note 6) IL 3.0 4.0 6.0 mA Ta=25℃
Starting Discharge Voltage VS
(Note 2) 1300 - - Vrms Ta=5℃
Note 1 : Please design your lamp driving circuit (inverter) according to the above
specifications, and inform HITACHI about it.
Note 2 : Starting discharge voltage is increased when LCM is operating under low
temperature.
Please check the characteristics of your inverter before applying to your set.
Note 3 : Average life time of CFL will be decreased when LCM is operating under low
temperature.
Note 4 : Under lower driving frequency of an inverter, a certain Backlight system (CFL &
CFL reflection sheet) may generate a sound noise. Before designing the inverter,
please consider the driving frequency and noise.
Note 5 : When IL is over 6.0mA, it may cause uneven contrast near CFL location, due
to heat dispersion from CFL.
Note 6 : We recommend to equip protection circuit (To stop output) which works under
abnormal operation to the inverter for CFL
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2705-TX14D11VM1CAB-4 PAGE 5-3/3
Sh.
No.
6. OPTICAL CHARACTERISTICS
6.1 OPTICAL CHARACTERISTICS OF LCD Ta=25℃ (Backlight on)
ITEM SYMBOL CONDITION MIN. TYP. MAX. UNIT NOTE
θx
=0°,K≧5.0 - 65 - deg 1~5
θx'
=180°,K≧5.0 65 deg 1~5
θy
=90°,K≧5.0 70 deg 1~5
Viewing Area
θy'
=270°,K≧5.0 - 50 - deg 1~5
Contrast Ratio K
=0°,θ=0° 120 350 - - 5
Response Time (rise+fall) tr+tf
=0°,θ=0° - (45) - ms 6
x 0.56 0.61 0.66 -
Red y 0.28 0.33 0.38 -
x 0.25 0.30 0.35 -
Green y 0.52 0.57 0.62 -
x 0.09 0.14 0.19 -
Blue y 0.03 0.08 0.13 -
x 0.24 0.29 0.34 -
Color Tone
(Primary Color)
White y
=0°, θ=0°
0.24 0.29 0.34 -
(Measurement condition : HITACHI standard)
(Note 3~6) : See next page.
Note 1 : Driving Condition
Display Pattern : White Raster
ICFL Current : 4mA
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2706-TX14D11VM1CAB-4 PAGE 6-1/3
Sh.
No.
Note 2 : Measurement Condition
(Transmitance)
LCD panel
BM-5A or
Similar equipment
6.2 OPTICAL CHARACTERISTICS OF BACKLIGHT
ITEM MIN. TYP. MAX. UNIT NOTE
Brightness - (480) - cd/m2 IL=4.0 mA (Note 1,2)
Rise Time - 3 - Minute IL=4.0 mA
Brightness 80%
Brightness Uniformity - - ±25 % Under mentioned
(Note 1,3)
(Measurement condition : HITACHI standard)
CFL:0h operation, Ta=25C
Display data should all be “ON”
Note 1 : Measurement after 10 minutes from CFL operating.
Average value of 9 points (Note 3)
Note 2 : Brightness control : 100%.
Note 3 : Measurement of the following 9 places on the display.
Note 4 : Definition of the brightness tolerance.
P3
P2 P5
P6 P9
P8
P7P4P1
Y=780
Y=480
Y=180
X=120
X=70
X=170
Average brightness
Max. brightness or Min. brightness - Average brightness ×100
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2706-TX14D11VM1CAB-4 PAGE 6-3/3
Sh.
No.
7.BLOCK DIAGRAM
CFL
CN2
GND
VL
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2707-TX14D11VM1CAB-4 PAGE 7-1/1
Sh.
No.
Touch Panel Touch Panel
Signals
Source Driver
Gate Driver
D1 D2 D960
G1
G2
G240
Timing
Controller
Power
Circuit
I/F(CN1)
Power Supply
TFT-LCD
Data / Clock
Timing Signals
8.INTERFACE TIMING
8.1 INTERFACE TIMING
ITEM MIN. TYP. MAX. UNIT SYMBOL REMARKS
Cycle time (142) (171) (206) tCLK
Low level Width 12 - - tWCL
High level Width 12 - - tWCH
Rise time - - 25 trCLK
Fall time - - 25
ns
tfCLK
DCLK
Duty 0.45 0.5 0.55 - D D= tCLKL/ CLK
Set up time 5 tSH
Hold time 10 ns tHH for DCLK
Cycle 370 (385) 397 tHP
Valid width 4 (5) - tCLK tWH
Hsync
Rise/Fall time - - 30 ns tHr,tHf
Set up 0 - - tSV
Hold 2 - -
tCLK tHV for Hsync
Cycle 251 (253) 261 tVP
Valid width 2 (2) tHP tWV
Vsync
Rise/Fall time - - 50 ns tVr,tVf
Set up time 5 - - tSI
Hold time 10 - - ns tHI for DCLK
Rise/Fall time - - 30 ns tIr,tIf
Horizontal back porch 28 (35) - tHBP
Horizontal front porch 22 (30) - tCLK tHFP
Vertical back porch 6 (7) - tVBP
DTMG
Vertical front porch 5 (6) - tHP tVFP
Set up time 5 - - tSD
Hold time 10 - - ns tHD for DCLK
Data
Rise/Fall time - - 25 ns tDr,tDf
Note : Vsync Cycle No. should be set to odd.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2708-TX14D11VM1CAB-4 PAGE 8-1/5
Sh.
No.
8.2 Timing Chart
(Data is latched negative edge trigger of DCLK)
Note 1 : DTMG is definition of the above timing for Hsync and Vsync.
Note 2 : No matter when Hsync and Vsync is inputted ,this LCM can be driven
only DTMG Signal. DTMG should be set to low level when it is not input
valid data.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2708-TX14D11VM1CAB-4 PAGE 8-2/5
Sh.
No.
VSYNC，HSYNC，DTMG，
R0～5，G0～5，B0～5
DTMG
Vsync
DTMG
Hsync
Vsync
Hsync
DCLK
t
CLK
DCLK
DTMG
DATA
1.5V
t
CLKL
t
HD
t
SD
t
WCH
t
WCL
t
fCLK
t
rCLK
t
HI
t
SI
t
HH
t
SH
t
SV
t
HV
t
WH
t
HP
t
HFP
t
HBP
t
VP
t
WV
t
VBP
t
VFP
t
Hr
,t
Vr
t
Ir
,t
Dr
t
Hf
,t
Vf
t
If
,t
Df
V
IH
min.
V
IL
max.
Invalid DataInvalid Data
8.3 POWER ON/OFF SEQUENCE
Note 1 : 0V≦VI(t) ≦VDD(t)
VI(t) and VDD(t) is a surfeit of condition for power on/off.
Note 2 : Input Voltage(Signal) should not be set high impedance when power on.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2708-TX14D11VM1CAB-4 PAGE 8-3/5
Sh.
No.
3.0V
0.8 V
0.8V
VDD(t )
VI(t )
ON
POWER ON
t
1
≦ 15ms
0ms ＜
t
2
≦ 45ms
0.1s ≦
t
3
OFF
3.0V
t1t2t5t6
POWER OFF
5ms ≦
t
4
0ms ≦
t
5
≦ 45ms
0ms ≦
t
6
≦ 20ms
0.4s
≦
t
7
t7
t3t4
2.0 V
Power supply for Logic
Input Voltage (Signal)
Backlight
8.4 RELATIONSHIP BETWEEN DISPLAYED COLOR AND INPUT DATA
DATA SIGNAL
COLOR &
GRAY
SCALE
GRAY
SCALE
LEVELS R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5
Black - 0 0 0000000000 0 0 0 000
Blue - 0 0 0000000000 1 1 1 111
Green - 0 0 0 000111111 0 0 0 000
Cyan - 0 0 0000111111 1 1 1 111
Red - 1 1 1111000000 0 0 0 000
Magenta - 1 1 1 111000000 1 1 1 111
Yellow - 1 1 1111111111 0 0 0 000
Basic
Color
White - 1 1 1111111111 1 1 1 111
Black GS0 0 0 0000000000 0 0 0 000
GS1 1 1 0000000000 0 0 0 000
GS2 0 1 0000000000 0 0 0 000
↓ ↓ ↓ ↓
↓ ↓ ↓ ↓
GS61 1 0 1111000000 0 0 0 000
↑
Darker
↑
↓
Brighter
↓ GS62 0 1 1111000000 0 0 0 000
Red
Red GS63 1 1 1111000000 0 0 0 000
Black GS0 0 0 0000000000 0 0 0 000
GS1 0 0 0000100000 0 0 0 000
GS2 0 0 0000010000 0 0 0 000
↓ ↓ ↓ ↓
↓ ↓ ↓ ↓
GS61 0 0 0000101111 0 0 0 000
↑
Darker
↑
↓
Brighter
↓ GS62 0 0 0000011111 0 0 0 000
Green
Green GS63 0 0 0 000111111 0 0 0 000
Black GS0 0 0 0000000000 0 0 0 000
GS1 0 0 0000000000 1 0 0 000
GS2 0 0 0000000000 0 1 0 000
↓ ↓ ↓ ↓
↓ ↓ ↓ ↓
GS61 0 0 0000000000 1 0 1 111
↑
Darker
↑
↓
Brighter
↓ GS62 0 0 0000000000 0 1 1 111
Blue
Blue GS63 0 0 0000000000 1 1 1 111
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2708-TX14D11VM1CAB-4 PAGE 8-4/5
Sh.
No.
8.5 INTERNAL PIN CONNECTION
CN1 JAE : FA5B040HP1R3000(Au plating) (Suitable FPC : t0.3±0.03mm，0.5±0.03mm pitch)
PIN No. SIGNAL FUNCTION
1 VDD Power Supply for Logic
2 VDD Power Supply for Logic
3 VDD Power Supply for Logic
4 VDD Power Supply for Logic
5 NC No Connection
6 DTMG Timing Signal for Data
7 VSS GND
8 DCLK Dot Clock
9 VSS GND
10 NC No Connection
11 VSS GND
12 B5
13 B4
14 B3
Blue Data
15 VSS GND
16 B2
17 B1
18 B0
Blue Data
19 VSS GND
20 G5
21 G4
22 G3
Green Data
23 VSS GND
24 G2
25 G1
26 G0
Green Data
27 VSS GND
28 R5
29 R4
30 R3
Red Data
31 VSS GND
32 R2
33 R1
34 R0
Red Data
35 (IC) No Connection
36 VSS GND
37 NC No Connection
38 NC No Connection
39 NC No Connection
40 NC No Connection
CN2 JST Housing : BHR-03VS-1
PIN
No. SIGNAL LEVEL FUNCTION
1 VCFL - Power Supply for CFL
2 NC - No connection
3 VSS - GND for CFL
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2708-TX14D11VM1CAB-4 PAGE 8-5/5
Sh.
No.
10. APPEARANCE STANDARD
10.1 APPEARANCE INSPECTION CONDITION
Visual inspection should be done under the following condition.
(1) The inspection should be done in a dark room.(More than 1000(lx) and non-directive)
(2) The distance between eyes of an inspector and the LCD module is 30cm.
(3) The viewing zone is shown the figure.
The θ is defined as θ ≦45° for LCM power off
θ ≦5° for LCM power on
10.2 DEFINITION OF ZONE
eye eye
θθ
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2710-TX14D11VM1CAB-4 PAGE 10-1/5
Sh.
No.
A zone
B zone
C zone
Display area (pixel area)
Until 1mm outside around display area
Metal bezel area
(include I/F connector)
Bezel
LCD
10.3 APPEARANCE SPECIFICATION
(1)LCD Appearance
*) If the problem related to this section occurs about this item , the responsible
persons of both party (Customer and HITACHI) will discuss the matter in detail.
No. ITEM CRITERIA APPLIED
ZONE
Length
L(mm) Width
W(mm) Maximum
number
acceptable
Minimum
space
Ignored W≦0.02 Ignored -
L≦40 0.02＜W≦0.04 10 -
Scratches
L≦20 W≦0.04 10 -
A,B
Dent Distinguished one is acceptable
(To be judged by HITACHI standard) A
Wrinkles in Polarizer Same as above A
Average diameter
D(mm) Maximum number
acceptable
D≦0.2 Ignored
0.2＜D≦0.3 12
0.3＜D≦0.5 3
Bubbles
0.5＜D none
A
Filamentous (Line shape)
Length
L(mm) Width
W(mm) Maximum number
acceptable
L≦2.0 W≦0.03 Ignored
L≦3.0 0.03＜W≦0.05 6
L≦2.5 0.05＜W≦0.1 1
A,B
Round(Dot shape)
A
verage diameter
D(mm) Maximum number
acceptable Minimum Space
D＜0.2 Ignored -
0.2≦D＜0.3 10 10 mm
0.3≦D＜0.4 5 30 mm
0.4≦D none -
The total number Filamentous + Round=10
Stains
Foreign
Materials
Dark Spot
Those wiped out easily are acceptable
A,B
Color Tone To be judged by HITACHI STANDARD A
Color Uniformity Same as above A
Maximum
number
acceptable
Sparkle mode 1 dot 4
2 dots 1
Total (Note.(3)-(f)) 5
Black mode 1 dot 5
2 dots 2
Total (Note.(3)-(f)) 5
L
C
D
Dot Defect
Total (Note.(3)-(f)) 10
A
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2710-TX14D11VM1CAB-4 PAGE 10-2/5
Sh.
No.
(2) CFL BACKLIGHT APPEARANCE
No. ITEM CRITERIA APPLIED
ZONE
Average diameter
D(mm) Maximum number acceptable
D≦0.4 ignored
Dark Spots
White Spots
Foreign Materials
(Spot) 0.4＜D none
A
Width
W(mm) Length
L(mm) Maximum number
acceptable
L≦2.5 1
W≦0.2 2.5＜L None
Foreign Materials
(Line)
0.2<W - none
A
Width
W(mm) Length
L(mm) Maximum number
acceptable
W≦0.1 - ignored
L≦11.0 1
0.1＜W≦0.2 11.0＜L None
C
F
L
B
A
C
K
L
I
G
H
T
Scratches
0.2＜W - none
A
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2710-TX14D11VM1CAB-4 PAGE 10-3/5
Sh.
No.
(3)Touch panel appearance
Visual inspection should be done under the following condition.
*) The inspection should be done in a dark room. (more than 500 (lx) and non-directive)
*) The distance between eyes of an inspector and the LCD module is 30 cm.
*) The viewing angle≦60°.
No. ITEM CRITERIA APPLIED
ZONE
Width
W(mm) Length
L(mm) Maximum number
acceptable
W＞0.1 L≧10 None
0.10≧W＞0.05 L＜10 4 pcs max.
Scratches
0.05≧W L＜10 Ignored
A,B
Filamentous (Line shape)
Width
W(mm) Length
L(mm) Maximum number
acceptable
W＞0.10 - Dust (circular)
0.10≧W＞0.05 3＜L None
0.05≧W L≦3 Ignored
A,B
Round(Dot shape)
Average diameter
D(mm) Maximum number
acceptable
D＞0.35 None
A,B
0.35≧D＞0.25 6 psc max. B
Foreign
Materials
Dark Spot
D≦0.25 Ignored A,B
Newton Ring
(Touch Panel) Need to discuss with customer A,B
Touch Panel
Uncleanliness No conspicuous dirt A
T
O
U
C
H
P
A
N
E
L
Rubbing Scratch To be judged by HITACHI standard -
(4) Glass indentation
ITEM SPECIFICATIONS
Common
Indentation
X
Z
Y
Corner
Broken
ZY
X
Proceeding
Crack None
Other
Y
Y≦1
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2710-TX14D11VM1CAB-4 PAGE 10-4/5
Sh.
No.
X Y Z
≦5.0 ≦3.0 ≦1.1
X Y Z
≦3 ≦3 ≦1.1
Blistering Puffiness
R G B R G B R G B
x
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2710-TX14D11VM1CAB-4 PAGE 10-5/5
Sh.
No.
Note 2 : Definition of length (L) and width (W)
a
b
Note 1 : Definition of average diameter (D)
a+b
2
D=
W
L
Note 3 : Definition of dot defect
(a) Dot Defect : Defect Area ＞1/2 dot
(b) Sparkle mode : Brightness of dot is more than 30% at Black raster.
(c) Black mode : Brightness of dot is less than 70% at R.G.B raster.
(d) 1 dot : Defect dot is isolated , not attached to other defect dot.
(e) N dot : N defect dots are consecutive (fig.1).
(N means the number of defect dots.)
2 dots defect included defect dot “X” is defined
as follows.
Adjacent dots to defect dot “X” :
(f) Counting definition of adjacent dots (1 set) : same as 1 dot defect.
(g) Those wiped out easily are acceptable.
( fig .1)
Touch Panel
Gauge
0.6 mm max.
11. PRECAUTION IN DESIGN
11.1 MOUNTING PRECAUTION
Please mount the LCD Module by using mounting holes provided. While mounting
please pay attention to the followings.
(1) To prevent the module cover from being pressed, the distance between the
module and the fitting plate, which means the length of the spacers, should be
shorter than 1.0mm.
(2) The use of protective spacers are recommend in order to protect the module
from shock.
(3) For the module to be used at upright position, the case shall have a structure
where the touch panel screen does not shift with its own weight.
11.2 PRECAUTIONS AGAINST ELECTROSTATIC DISCHARGE
As this module contains C-MOS LSIs, it is not strong against electrostatic discharge.
Make certain that the operator’s body is connected to the ground through a list
band , etc. And don’t touch I/F pins directly.
Touch
p
anel
S
p
acer
Protective s
p
acer
S
p
ace
Customer’s housing
The module
Example of mounting
(
T.B.D
)
(
T.B.D
)
(
T.B.D
)
152.0 ±0.3
(
T.B.D
)
(
T.B.D
101.0 ±0.3
(T.B.D)
(
T.B.D
)
Lower panel
Protective s
p
acer 4-
5.0
Upper panel
Spacer 4-
7.0
Location of s
p
acers
Unit : mm
Scale: NTS
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2711-TX14D11VM1CAB-4 PAGE 11-1/3
Sh.
No.
11.3 HANDLING PRECAUTIONS
(1) Since the Touch Panel on the top, and the frame on the bottom tend to be
easily damaged, they should be with full care so as not to get them touched,
pushed or rubbed by a piece on glass, tweezers and anything else which are
harder a pencil lead 2H.
(2) As the adhesives used for adhering upper/lower polarizer’s and frame are made
of organic substances which will be deteriorated by a chemical reaction with such
chemicals as acetone, toluene, ethanol and isopropyl alcohol. The following are
recommended for use :
normal hexane
Please contact with us when it is necessary for you to use chemicals other than
the above.
(3) Lightly wipe to clean the dirty surface with absorbent cotton or other soft material
like chamois, soaked in the recommended chemicals without scrubbing it hardly.
Always wipe the surface horizontally or vertically. Never give a wipe in a circle.
To prevent the display surface from damage and keep the appearance in good
state, it is sufficient, in general, to wipe it with absorbent cotton.
(4) Immediately wipe off saliva or water drop attached on the display area because
it may cause deformation or faded color.
(5) Fogy dew deposited on the surface may cause a damage, stain or dirt to the
polarizer.
When you need to take out the LCD module from some place at low temperature
for test, etc.
It is required to be warmed them up to temperature higher than room temperature
before taking them out.
(6) Touching the display area or I/F pins with bare hands or contaminating them are
prohibited, because the stain on the display area and poor insulation between
terminals are often caused by being touched with bare hands.
(Some cosmetics are detrimental to polarizer’s.)
(7) In general, the glass is fragile so that, especially on its periphery, tends to be
cracked or chipped in handling. Please do not give the LCD module sharp shocks
by falling, etc.
(8) Maximum pressure to the surface must be less than 1.96×104 Pa.
And if the pressure area is less than 1cm2 , maximum pressure must be less than
1.96N.
(9) Since the metal width is narrow on these locations (see page 9-1/2), please careful
with handling.
(10) Top sheets shall be cleaned gently using a soft cloth such as those used for
glasses.
Hard wiping accumulated dust will leave scars on the surface even using a cloth.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2711-TX14D11VM1CAB-4 PAGE 11-2/3
Sh.
No.
11.4 OPERATION PRECAUTION
(1) Using a LCM module beyond its maximum ratings may result in its permanent
destruction.
LCM module’s should usually be used under recommended operating conditions
shown in chapter 4. Exceeding any of these conditions may adversely affect
its reliability.
(2) Response time will be extremely delayed at lower temperature than the specified
operating temperature range and on the other hand LCD’s shows dark blue at
higher temperature.
However those phenomena do not main defects of the LCD module. Those
phenomena will disappear in the specified operating temperature range.
(3) If the display area is pushed hard during operation, some display patterns will be
abnormally display.
(4) A slight dew depositing on terminals may cause electrochemical reaction which
leads to terminal open circuit. Please operate the LCD module under the relative
condition of 40℃ 85%RH.
(5) Resistance range : Your controller shall be set up to allow the resistance range of
Touch Panel specified in our CAS.
(6) Pointed position of Touch Panel may shift owing to a change in resistance of
Touch Panel depending on the operation condition . To compensate this shift, the
set shall be given a calibration function.
(7) Input shall be made with a stylus pen (poly acetal , R0.8). Chances are very high that
use of a metal piece including a ball point pen or sharp edge will impair accuracy.
(8) The Touch Panel is an auxiliary input device. The system shall be designed to have
other input device.
11.5 STORAGE
In case of storing LCD module for a long period of time (for instance, for years) for
the purpose of replacement use, the following precautions necessary.
(1) Store the LCD modules in a dark place; do not expose them to sunlight or
ultraviolet rays.
(2) Keep the temperature between 10℃ and 35℃ at normal humidity.
(3) Store the LCD modules in the container which is used for shipping from us.
(4) No articles shall be left on the surface over an extended period of time.
11.6 SAFETY
Wear finger cots or gloves whenever handling or assembling a Touch Panel its
glass edges are sharp.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2711-TX14D11VM1CAB-4 PAGE 11-3/3
Sh.
No.
12. DESIGNATION OF LOT MARK
12.1 LOT MARK
Lot mark is consisted of 5 digits for production lot and
6 digits for production control.
12.2 SERIAL No.
Serial No. is consisted of 6 digits number (000001~999999).
12.3 LOCATION OF LOT MARK
Label is bring attached on the back side of module.
12.4 REVISION(Rev.) CONTROL
Rev No. ITEM
A CN1 JAE : FA5B040HF1
B CN1 JAE : FA5B040HP1R3000
Week
(day in calendar) Figure in
lot mark
1~ 7 1
8~14 2
15~21 3
22~28 4
29~31 5
Month Figure in
lot mark Month Figure in
lot mark
Jan. 01 Jul. 07
Feb. 02 Aug. 08
Mar. 03 Sep. 09
Apr. 04 Oct. 10
May 05 Nov. 11
Jun. 06 Dec. 12
Year Figure in
lot mark
2010 0
2011 1
2012 2
2013 3
2014 4
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2712-TX14D11VM1CAB-4 PAGE 12-1/1
Sh.
No.
1408
Year
Month
Week
T
Digits for production control
T : Made in Taiwan
13. PRECAUTION FOR USE
(1) A limit sample should be provided by the both parities on an occasion when the
both parties agree to its necessity.
Judgment by a limit sample shall take effect after the limit sample has been
established and confirmed by the both parties.
(2) On the following occasions, the handling of the problem should be decided
through discussion and agreement between responsible persons of the both
parties.
(1) When a question is arisen in the specifications.
(2) When a new problem is arisen which is not specified in this specifications.
(3) When an inspection specifications change or operating condition change
by customer is reported to HITACHI, and some problem is arisen in the
specification due to the change.
(4) When a new problem is arisen at the customer’s operating set for sample
evaluation.
(3) Regarding the treatment for maintenance and repairing, both parties will discuss
it in six months later after latest delivery of this product.
The precaution that should be observed when handling LCM have been explained
above.
If any points are unclear or if you have any requests , please contact with HITACHI.
KAOHSIUNG HITACHI
ELECTRONICS CO.,LTD. DATE Nov.12,’10 7B64PS 2713-TX14D11VM1CAB-4 PAGE 13-1/1
Sh.
No.
