a~í~=pÜÉÉía~í~=pÜÉÉí
SMT power inductors
ERU 13, helically wound
Series/Type: B82559*A013
Date: November 2012
© EPCOS AG 2015. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
EPCOS AG is a TDK Group Company.
211/12
Please read Cautions and warnings and
Important notes at the end of this document.
Rated inductance 0.5 ... 3.9 µH
Saturation current 12 ... 30 A
Construction
Ferrite core
Magnetically shielded
Winding: enamel copper flat wire
Self-leaded construction under body termination
Features
Very high rated current
Extremely low DC resistance
Very low profile and smallest possible footprint
Suitable for pick and place processes
Applications
Energy storage chokes for
DC/DC converters
VRM modules
POL converters
Terminals
Lead-free tinned
Marking
Manufacturer, middle block of ordering code,
inductance, date code (YYWW)
Delivery mode and packing units
24-mm blister tape, wound on 330-mm dia. reel
4.95 mm height = 750 pcs./reel
5.95/6.00 mm height = 500 pcs./reel
B82559*A013SMT power inductors
ERU 13
Helically wound
311/12
Please read Cautions and warnings and
Important notes at the end of this document.
Dimensional drawing and layout recommendation
Dimensions in mm
Taping and packing
Blister tape Reel
Dimensions in mm
IND0351-A
62±1.5
22.4 max. 13±0.2
330
2
+0
_
16.4
0
+1.5
_
6.95 max. for component height = 5.95 mm
1)
B-B
B
B
Component
+0.1
0
1.5
_
4±0.1
2±0.1
16±0.1
1.5 min.
12.8
Direction of unreeling
IND0398-P-E
11.5±0.1
24±0.3
1.7±0.1
1)
5.95 max.
11.2
B82559*A013SMT power inductors
ERU 13
Helically wound
411/12
Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and measuring conditions
Characteristics and ordering codes
Sample kit available. Ordering code: B82559X001
For more information refer to chapter “Sample kits”.
Rated inductance LRMeasured with Wayne-Kerr 3260A/3265B at 10 kHz, 0.1 V, +20 °C
Inductance tolerance 10%
Saturation current Isat Current that will result in approx. 20% drop in inductance value.
Temperature response needs to be verified in specific applications.
Test results on request.
DC resistance Rtyp Measured at +20 °C, tolerance 10%
(closer tolerances on request), typical values
Solderability +235 °C, 5 s, wetting >90% (IEC 60068-2-58)
Resistance to soldering heat To JEDEC J-STD 020D
Operating temperature 40 °C … +130 °C
Storage conditions (packaged) –25 °C … +40 °C, 75% RH
Weight 2.2 g (height = 4.95 mm), 2.6 g (height = 5.95/6.00 mm)
LR
H
Isat
A
Rtyp
m
Height h max.
mm
Ordering code
0.50 30 0.78 4.95 B82559A0501A013
0.95 25 1.12 5.95 B82559A0951A013
1.1 20 1.72 4.95 B82559A0112A013
1.4 22 1.50 6.00 B82559A0142A013
2.15 15 3.20 4.95 B82559A0222A013
2.4 16.5 2.76 5.95 B82559A0242A013
3.0 13 4.00 4.95 B82559A0302A013
3.9 12 4.80 5.95 B82559A0392A013
B82559*A013SMT power inductors
ERU 13
Helically wound
511/12
Cautions and warnings
Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
Particular attention should be paid to the derating curves given there.
The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation.
Washing processes may damage the product due to the possible static or cyclic mechanical
loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts,
which might lead to reduced reliability or lifetime.
The following points must be observed if the components are potted in customer applications:
Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
It is necessary to check whether the potting material used attacks or destroys the wire
insulation, plastics or glue.
The effect of the potting material can change the high-frequency behaviour of the components.
Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.
Please read Cautions and warnings and
Important notes at the end of this document.
611/12
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in which
the malfunction or failure of an electronic component could endanger human life or health (e.g.
in accident prevention or life-saving systems), it must therefore be ensured by means of suitable
design of the customer application or other action taken by the customer (e.g. installation of
protective circuitry or redundancy) that no injury or damage is sustained by third parties in the
event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products.
Consequently, we cannot guarantee that all products named in this publication will always be
available. The aforementioned does not apply in the case of individual agreements deviating
from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS,
DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC,
MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL,
SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap
are trademarks registered or pending in Europe and in other countries. Further information will
be found on the Internet at www.epcos.com/trademarks.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
EPCOS:
B82559X1
EPCOS / TDK:
B82559A0501A013 B82559A0951A013 B82559A0112A013 B82559A0142A013 B82559A0222A013
B82559A0242A013 B82559A0302A013 B82559A0392A013 B82559A112A13 B82559A242A13 B82559A501A13
B82559A222A13 B82559A951A13 B82559A142A13 B82559A392A13 B82559A302A13