Document 621-1 Coupled Inductors - MSD7342 For Flyback, SEPIC and other Applications * Tight coupling (k 0.97) and 200 V isolation make the MSD7342 series of coupled inductors ideal for use in a variety of circuits including flyback, multi-output buck and SEPIC. * They provide high inductance, high efficiency and excellent current handling in a rugged, low cost part. * Can also be used as two single inductors connected in series or parallel, as a common mode choke or as a 1 : 1 transformer. + + D L1 VIN C L2 VOUT C - SW - Typical Flyback Converter L2 D + VOUT C AUX - + 0.295 max 7,5 0.295 max 7,5 123 VIN Dot indicates pin 1 1 2 L1 L2 4 2 1 3 4 Recommended Land Pattern 0.110 2,8 Dimensions are in 0.083 2,1 2 1 3 4 0.130 3,3 0.043 1,10 0.063 1,6 inches mm VOUT C - D + L1 VIN - 3 D Typical Buck Converter with auxiliary output 0.091 2,3 0.150 3,8 SW - 0.181 max 4,6 0.028 0,7 + L1 + C1 L2 Q C Typical SEPIC schematic VOUT - Core material Ferrite Terminations RoHS compliant matte tin over nickel over phos bronze. Other terminations available at additional cost. Weight 0.76 - 0.87g Ambient temperature -40C to +85C with Irms current, +85C to +125C with derated current Storage temperature Component: -40C to +125C. Tape and reel packaging: -40C to +80C Winding to winding isolation 200 Vrms Resistance to soldering heat Max three 40 second reflows at +260C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 250/7 reel; 1000/13 reel Plastic tape: 16 mm wide, 0.4 mm thick, 12 mm pocket spacing, 4.9 mm pocket depth PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf. Specificationssales@coilcraft.com subject to change without notice. US +1-847-639-6400 Please check our website for latest information. UK +44-1236-730595 sales@coilcraft-europe.com Taiwan +886-2-2264 3646 sales@coilcraft.com.tw China +86-21-6218 8074 sales@coilcraft.com.cn Singapore + 65-6484 8412 sales@coilcraft.com.sg Document 621-1 Revised 01/13/12 (c) Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 621-2 Coupled Inductors - MSD7342 Series Coupling Leakage Inductance2 DCR max3 SRF typ4 coefficient L typ5 Part number1 20% (H) (Ohms) (MHz) typ (H) MSD7342-252ML_ MSD7342-332ML_ MSD7342-472ML_ MSD7342-562ML_ MSD7342-682ML_ MSD7342-822ML_ MSD7342-103ML_ MSD7342-123ML_ MSD7342-153ML_ MSD7342-183ML_ MSD7342-223ML_ MSD7342-273ML_ MSD7342-333ML_ MSD7342-393ML_ MSD7342-473ML_ MSD7342-563ML_ MSD7342-683ML_ MSD7342-823ML_ MSD7342-104ML_ MSD7342-124ML_ MSD7342-154ML_ MSD7342-184ML_ MSD7342-224ML_ MSD7342-274ML_ MSD7342-334ML_ MSD7342-394ML_ MSD7342-474ML_ MSD7342-564ML_ MSD7342-684ML_ MSD7342-824ML_ MSD7342-105ML_ 2.5 3.3 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 0.033 0.037 0.051 0.063 0.070 0.075 0.100 0.120 0.130 0.170 0.220 0.250 0.270 0.380 0.420 0.460 0.600 0.680 0.770 1.03 1.35 1.52 1.72 2.41 2.70 3.05 4.00 4.43 5.00 6.80 7.80 55 43 35 32 30 27 22 20 18 15 13.5 12.0 11.0 10.0 9.5 8.7 7.3 6.2 5.5 4.5 4.0 3.8 3.5 3.3 3.0 2.8 2.6 2.5 2.3 2.2 2.0 0.97 0.99 0.99 0.99 0.99 0.98 0.98 0.98 0.98 >0.99 >0.99 >0.99 >0.99 0.99 >0.99 >0.99 >0.99 0.99 >0.99 >0.99 >0.99 >0.99 >0.99 >0.99 >0.99 0.99 0.99 >0.99 0.99 >0.99 >0.99 0.14 0.09 0.11 0.09 0.14 0.25 0.30 0.36 0.49 0.16 0.20 0.20 0.15 0.70 0.30 0.51 0.51 1.17 0.96 0.61 0.54 0.75 1.43 1.56 1.65 4.73 5.50 4.85 7.59 8.01 8.69 10% drop Isat (A)6Irms (A) 20% 30% both one drop drop windings7 winding8 6.0 5.2 4.1 3.9 3.7 3.3 2.8 2.5 2.2 2.0 1.9 1.7 1.5 1.3 1.2 1.1 1.0 0.90 0.80 0.70 0.65 0.62 0.59 0.55 0.49 0.45 0.41 0.38 0.36 0.30 0.27 6.2 5.3 4.3 4.1 3.8 3.4 2.9 2.6 2.3 2.2 2.0 1.8 1.6 1.4 1.3 1.2 1.1 1.00 0.92 0.80 0.76 0.66 0.62 0.57 0.52 0.47 0.43 0.40 0.37 0.32 0.29 6.3 5.4 4.6 4.2 3.9 3.5 3.0 2.7 2.4 2.3 2.1 1.9 1.7 1.5 1.4 1.3 1.2 1.1 0.98 0.90 0.80 0.73 0.66 0.60 0.54 0.50 0.46 0.42 0.38 0.35 0.31 2.17 2.05 1.74 1.57 1.49 1.44 1.24 1.14 1.09 0.95 0.84 0.79 0.76 0.64 0.61 0.58 0.51 0.48 0.45 0.39 0.34 0.32 0.30 0.25 0.24 0.23 0.20 0.19 0.18 0.15 0.14 1. When ordering, please specify termination and packaging codes: Temperature rise calculation based on specified Irms MSD7342-105MLC Termination: L = RoHS compliant matte tin over nickel over phos bronze. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C = 7 machine-ready reel. EIA-481 embossed plastic tape (250 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13 machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (1000 parts per full reel). 2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent. When leads are connected in parallel, inductance is the same value. When leads are connected in series, inductance is four times the value. 3. DCR is for each winding. When leads are connected in parallel, DCR is half the value. When leads are connected in series, DCR is twice the value. 4. SRF measured using an Agilent/HP 4191A or equivalent. When leads are connected in parallel, SRF is the same value. 5. Leakage inductance is for L1 and is measured with L2 shorted. 6. DC current, at which the inductance drops the specified amount from its value without current. It is the sum of the current flowing in both windings. 7. Equal current when applied to each winding simultaneously that causes a 40C temperature rise from 25C ambient. See temperature rise calculation. 8. Maximum current when applied to one winding that causes a 40C temperature rise from 25C ambient. See temperature rise calculation. 9. Electrical specifications at 25C. Refer to Doc 639 "Selecting Coupled Inductors for SEPIC Applications." Refer to Doc 362 "Soldering Surface Mount Components" before soldering. Winding power loss = (IL12 + IL22 ) x DCR in Watts (W) 129C Temperature rise (t) = Winding power loss x W 129C t = (IL12 + IL22 ) x DCR x W 3.06 2.89 2.46 2.22 2.10 2.03 1.76 1.61 1.54 1.35 1.19 1.11 1.07 0.90 0.86 0.82 0.72 0.67 0.63 0.55 0.48 0.45 0.42 0.36 0.34 0.32 0.28 0.26 0.25 0.21 0.20 Example 1. MSD7342-123ML (Equal current in each winding) Winding power loss = (1.14 2 + 1.14 2) x 0.120 = 0.312 W 129C = 40C t = 0.312 W x W Example 2. MSD7342-123ML (IL1 = 1.4 A, IL2 = 0.6 A) Winding power loss = (1.4 2 + 0.6 2) x 0.120 = 0.278 W t = 0.278 W x 129C = 36C W Coupled Inductor Core and Winding Loss Calculator This web-based utility allows you to enter frequency, peak-to-peak (ripple) current, and Irms current to predict temperature rise and overall losses, including core loss. Visit www.coilcraft.com/coupledloss. Specificationssales@coilcraft.com subject to change without notice. US +1-847-639-6400 Please check our website for latest information. UK +44-1236-730595 sales@coilcraft-europe.com Taiwan +886-2-2264 3646 sales@coilcraft.com.tw China +86-21-6218 8074 sales@coilcraft.com.cn Singapore + 65-6484 8412 sales@coilcraft.com.sg Document 621-2 Document 621-2 Revised 01/13/12 Revised 02/23/11 (c) Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 621-3 Coupled Inductors - MSD7342 Series Typical L vs Current Typical L vs Frequency 10000 10000 1000 H 100 H 100 47 H 10 H 10 1000 H 1000 470 H Inductance (H) Inductance (H) 1000 470 H 100 H 100 47 H 10 H 10 4.7 H 4.7 H 1 0.01 1 0.1 10 1 0.1 Current (A) 1 10 100 Frequency (MHz) Irms Derating 120 110 90 80 70 60 50 40 25C Percent of rated Irms 100 30 20 10 0 -40 -20 0 20 40 60 80 100 120 140 Ambient temperature (C) Specificationssales@coilcraft.com subject to change without notice. US +1-847-639-6400 Please check our website for latest information. UK +44-1236-730595 sales@coilcraft-europe.com Taiwan +886-2-2264 3646 sales@coilcraft.com.tw China +86-21-6218 8074 sales@coilcraft.com.cn Singapore + 65-6484 8412 sales@coilcraft.com.sg Document 621-3 Document 621-3 Revised 01/13/12 Revised 02/23/11 (c) Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information.