TLP2601 TOSHIBA Photocoupler GaAAs Ired & Photo-IC TLP2601 Isolated Line Receiver Simplex / Multiplex Data Transmission Computer-Peripheral Interface Microprocessor System Interface Digital Isolation for A/D, D/A Conversion Direct Replacement for HCPL-2601 Unit: mm The TOSHIBA TLP2601 a photocoupler which combines a GaAAs IRed as the emitter and an integrated high gain, high speed photodetector. The output of the detector circuit is an open collector, Schottky clamped transistor. A Faraday shield integrated on the photodetector chip reduces the effects of capacitive coupling between the input LED emitter and the high gain stages of the detector. This provides an effective common mode transient immunity of 1000V/s. * Input current thresholds: IF = 5mA (max) * Isolation voltage: 2500Vrms (min) * Switching speed: 10MBd * Common mode transient immunity: 1000V/s (min) * Guaranteed performance over temp.: 0C to 70C * UL Recognized: UL1577, file No. E67349 TOSHIBA 11-10C4 Weight: 0.54 g (typ.) P in Configuration (top view) Truth Table (positive logic) Input Enable Output H H L L H H H L H L L H 1 8 2 7 3 6 4 5 SHIELD Schematic IF A 0.01 to 0.1F bypass capacitor must be connected between pins 8 and 5 (see Note 1). 2 VF ICC IO + 8 6 3 VCC VO SHIELD 5 IE GND 7 VE Start of commercial production 1985/01 1 2014-09-01 TLP2601 Recommended Operating Conditions Characteristic Symbol Min Typ. Max Unit Input current, low level IFL 0 250 A Input current, high level IFH 6.3 (*) 20 mA Supply voltage**, output VCC 4.5 5.5 V High level enable voltage VEH 2.0 VCC V Low level enable voltage VEL 0 0.8 V N 8 Topr 0 70 C Fan out (TTL load) Operating temperature Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the device. Additionally, each item is an independent guideline respectively. In developing designs using this product, please confirm specified characteristics shown in this document. (*) 6.3mA is a guard banded value which allows for at least 20% CTR degradation. Initial input current threshold value is 5.0 mA or less. **This item denotes operating ranges, not meaning of recommended operating conditions. Absolute Maximum Ratings (no derating required) Symbol Rating Unit Forward current IF 20 mA Reverse voltage VR 5 V Output current IO 25 mA Output voltage VO -0.5~7 V Supply voltage (1 minute maximum) VCC 7 V Enable input voltage (not to exceed VCC by more than 500mV) VE 5.5 V Output collector power dissipation PO 40 mW Operating temperature range Topr -40~85 C Storage temperature range Tstg -55~125 C Detector LED Characteristic Lead solder temperature (10s) Isolation voltage (R.H. 60%, AC 1minute) (**) (Note 10) Tsol BVS 260 C 2500 Vrms 3540 Vdc Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). (**) 1.6mm below seating plane. 2 2014-09-01 TLP2601 Electrical Characteristics (Ta = 0C ~70C unless otherwise noted) Characteristic Symbol Test Condition Min Typ. Max Unit High level output current IOH VCC = 5.5V, VO = 5.5V IF = 250A, VE = 2.0V 1 250 A Low level output voltage VOL VCC = 5.5V, IF = 5mA VE = 2.0V, IOL(sinking) = 13mA 0.4 0.6 V High level supply current ICCH VCC = 5.5V, IF = 0, VE = 0.5V 7 15 mA Low level supply current ICCL VCC = 5.5V, IF = 10mA, VE = 0.5V 12 19 mA Low level enable current IEL VCC = 5.5V, VE = 0.5V -1.6 -2.0 mA High level enable current IEH VCC = 5.5V, VE = 2.0V -1 mA High level enable voltage VEH 2.0 Low level enable voltage VEL 0.8 Input forward voltage VF IF = 10mA, Ta = 25 1.65 1.75 V Input reverse breakdown voltage BVR IR = 10A, Ta = 25 5 V Input capacitance CIN VF = 0, f = 1MHz 45 pF IF = 10mA -2.0 mV / C 1 A pF (Note 11) Input diode temperature coefficient VF/TA Input-output insulation leakage current II-O Relative humidity = 45% Ta=25, t = 5 second VI-O = 3000Vdc, (Note 10) Resistance (input-output) RI-O VI-O = 500V, R.H. 60% (Note 10) 5x10 Capacitance (input-output) CI-O f = 1MHz (Note 10) 10 14 10 0.6 V (**) All typ.values are at VCC = 5V, Ta = 25C. 3 2014-09-01 TLP2601 Switching Characteristics (Ta = 25, VCC = 5 V) Characteristic Symbol Propagation delay time to high output level tpLH Propagation delay time to low output level tpHL Output rise time (10-90%) tr Output fall time (90-10%) tf Propagation delay time of enable from VEH to VEL Test Circuit Test Condition 1 RL = 350, CL = 15pF IF = 7.5mA (Note 2), (Note 3), (Note 4)&(Note 5) RL = 350, CL = 15pF IF = 7.5mA VEH = 3.0V VEL = 0.5V (Note 6) & (Note 7) tELH 2 Propagation delay time of enable from VEL to VEH Common mode transient immunity at high output level tEHL VCM = 400V RL = 350 VO(min) = 2V IF = 0mA, CMH 3 Common mode transient immunity at low output level VCM = 400V RL = 350 VO(max) = 0.8V IF = 7.5mA, CML 4 Min Typ. Max Unit 60 75 ns 60 75 ns 30 ns 30 ns 25 ns 25 ns 1000 10000 V/s -1000 -10000 V/s (Note 9) (Note 8) 2014-09-01 TLP2601 Test Circuit 1. 5V Pulse generator ZO = 50 tr = 5ns IF = 7.5mA Input IF IF = 3.75mA tpHL IF Monitoring node 1.5V VOL 8 VCC 2 7 3 6 4 47 VOH tpLH Output VO 1 5 GND 0.1F Bypass tpHL and tpLH RL VO (*) CL Output monitoring node (*) CL is approximately 15pF which includes probe and stray wiring capacitance. Test Circuit 2. Pulse generator ZO = 50 tr = 5ns 3.0V Input VE 7.5mA dc IF 1.5V tEHL VOH tELH Input VE monitoring node 5V 1 1.5V 8 2 7 3 6 4 Output VO VCC GND 5 0.1F Bypass tELH and tEHL (*) CL VOL RL VO Output monitoring node (*) CL is approximately 15pF which includes probe and stray wiring capacitance. Test Circuit 3. Transient Immunity and Typical Waveforms. 90% VCM 10% 10% 90% tr tf IF 0V A B 5V VO VFF Switch at A: IF = 0mA VO VCC 8 2 7 3 6 4 Pulse gen. ZO = 50 GND 5V 0.1F Bypass 1 400V RL VO 5 VCM VOL Switch at B: IF = 5mA 5 2014-09-01 TLP2601 IF - VF VF / Ta - IF -2.6 Forward voltage temperature coefficient VF /Ta (mV/C) Ta = 25C 10 forward current IF (mA) 100 1 0.1 1.2 1.4 -2.0 -1.8 -1.6 100 VCC = 5V IF = 250A (V) Ta = 25C High level output current IOH (A) 6 RL=350 1k 4k 2 2 30 (mA) IOH - Ta VO - IF 1 10 3 Forward current IF (V) 8 4 1 0.3 1.8 1.6 Forward voltage VF Output voltage VO -2.2 -1.4 0.1 0.01 1.0 0 0 -2.4 3 4 Forward current IF 5 50 VCC = 5.5V 30 VO = 5.5V 10 5 3 6 1 (mA) 10 0 20 30 40 50 60 70 Ambient temperature Ta (C) VOL - Ta VO - IF 8 IF = 5mA RL=350 6 RL=4k Ta = 70C 4 0C 2 0 0 1 2 3 Forward current IF 4 5 VCC = 5.5V 0.5 Low level output voltage VOL (V) Output voltage VO (V) VCC = 5V VE = 2V IOL=16mA 0.4 12.8mA 9.6mA 6.4mA 0.3 6 0.2 (mA) 0 20 40 60 80 Ambient temperature Ta (C) 6 2014-09-01 TLP2601 tpHL, tpLH - IF tpHL, tpLH - Ta 120 120 tpLH RL= 4k RL=4k tpLH 100 tpLH 80 1k 350 tpLH tpHL 60 Propagation delay time tpHL, tpLH (ns) Propagation delay time tpHL, tpLH (ns) 100 350 1k 4k 40 tpLH 80 350 60 1k tpHL 4k 40 Ta = 25C 20 9 7 11 13 15 Forward current IF IF = 7.5mA 19 17 VCC = 5 V 20 VCC = 5V 0 5 350 1k 0 0 (mA) 10 20 30 40 50 60 70 60 70 Ambient temperature Ta (C) tEHL, tELH - Ta tr, tf - Ta 320 80 VCC = 5V IF = 7.5mA 70 RL= 4k tf 280 1k tf 60 350 tf 40 350 tr 20 0 0 VEH = 3V RL= 4k tELH IF = 7.5mA 60 80 Enable propagation delay time tEHL, tELH (ns) Rise, fall time tr, tf (ns) 300 VCC = 5V 1k 4k 10 20 30 40 50 60 50 40 1k tELH 30 350 tELH 350 20 70 tEHL 1k 4k 10 Ambient temperature Ta (C) 0 0 10 20 30 40 50 Ambient temperature Ta (C) 7 2014-09-01 TLP2601 Notes 1. The VCC supply voltage to each TLP2601 isolator must be bypassed by a 0.1F capacitor of larger.This can be either a ceramic or solid tantalum capacitor with good high frequency characteristic and should be connected as close as possible to the package VCC and GND pins of each device. 2. tpHL Propagation delay is measured from the 3.75mA level on the low to high transition of the input current pulse to the 1.5V level on the high to low transition of the output voltage pulse. 3. tpLH Propagation delay is measured from the 3.75mA level on the high to low transition of the input current pulse to the 1.5V level on the low to high transition of the output voltage pulse. 4. tf Fall time is measured from the 10% to 90% levels of the high to low transition on the output pulse. 5. tr Rise time is measured from the 90% to 10% levels of the low to high transition on the output pulse. 6. tEHL Enable input propagation delay is measured from the 1.5V level on the low to high transition of the input voltage pulse to the 1.5V level on the high to low transition of the output voltage pulse. 7. tELH Enable input propagation delay is measured from the 1.5V level on the high to low transition of the input voltage pulse to the 1.5V level on the low to high transition of the output voltage pulse. 8. CML The maximum tolerable rate of fall of the common mode voltage to ensure the output will remain in the low output state (i.e. VOUT < 0.8V). Measured in volts per microsecond (V / s). 9. CMH The maximum tolerable rate of fall of the common mode voltage to ensure the output will remain in the high state (i.e. VOUT > 2.0V). Measured in volts per microsecond (V / s). Volts/microsecond can be translated to sinusoidal voltages: V / s = (dv CM ) = fCM VCM (p.p.) dt Max. Example: VCM = 318Vpp when fCM = 1MHz using CML and CMH = 1000V / s data sheet specified minimum. 10. Device considered a two-terminal device: Pins 1, 2, 3 and 4 shorted together, and Pins 5, 6, 7 and 8 shorted together. 11. Enable input No pull up resistor required as the device has an internal pull up resistor. 8 2014-09-01 TLP2601 RESTRICTIONS ON PRODUCT USE * Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. * This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. * Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. * PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT ("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA sales representative. * Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. * Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. * The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. * ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. * GaAs (Gallium Arsenide) is used in Product. GaAs is harmful to humans if consumed or absorbed, whether in the form of dust or vapor. Handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose GaAs in Product. * Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. * Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS. 9 2014-09-01 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Toshiba: TLP2601 TLP2601(LF1,F)