6N136 6N136 General Purpose Type *OPIC Photocoupler Features Outline Dimensions 1. High speed response ( tPHL, tPLH : MAX.0.8s at RL=1.9k ) 2. High common mode rejection voltage ( CMH : TYP. 1kV/s ) 3. Standard dual-in-line package 4. Recognized by UL, file No. E64380 0.85 0.3 8 1.2 0.3 7 6 3 2 Absolute Maximum Ratings Emitter-base reverse withstand voltage (Pin 5 to 7) Output Average output current Peak output current Base current (Pin 7) Power dissipation *3 Isolation voltage Operating temperature Storage temperature *4Soldering temperature 5 1 2 3 4 6.5 0.5 6 0.8 4 7.62 0.3 0.5 TYP. 3.5 0.5 3.7 0.5 =0 to 13 0.26 0.1 NC 5 GND 2 Anode 6 VO 3 Cathode 7 VB 8 VCC 1 NC ( Ta=25C ) Symbol Rating IF IF I FM VR P VCC VO VEBO IO I OP IB PO Viso(rms) T opr T stg T so1 2.540.25 0.5 0.1 4 Forward current forward current Input *2Peak transient forward current Reverse voltage Power dissipation Supply voltage Output voltage 7 9.22 0.5 1. Computers, measuring instruments, control equipment 2. High speed line receivers, high speed logic 3. Telephone sets 4. Signal transmission between circuits of different potentials and impedances *1Peak 8 Primary side mark (Sunken place) Applications Parameter Internal connection diagram 5 6N136 1 ( Unit : mm ) 25 50 1 5 45 -0.5 to +15 -0.5 to +15 5 8 16 5 100 2.5 -55 to +100 -55 to +125 260 Unit mA mA A V mW V V V mA mA mA mW kV C C C * "OPIC" (Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and signalprocessing circuit integrated onto a single chip. *1 50% duty cycle, Pulse width=1ms Decreases at the rate of 1.6mA/C if the external temperature is 70C or more. *2 Pulse width1s, 300pulse/s *3 40 to 60% RH, AC for 1 minute *4 For 10 seconds Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://www.sharp.co.jp/ecg/ 6N136 Electro-optical Characteristics Parameter *5 Symbol MIN. TYP. MAX. Unit CTR(1) Ta=25C, IF =16mA VO =0.4V, VCC =4.5V 19 40 - % CTR(2) IF =16mA, VO =0.5V VCC =4.5V 15 43 - % V OL IF =16mA, VCC =4.5V, IO=2.4mA - 0.1 0.4 V IOH(1) Ta=25C, IF =0 VCC =VO =5.5V - 3.0 500 nA IOH(2) Ta=25C, I F =0 VCC =VO =15V - 0.01 1.0 A IOH(3) IF =0, VCC =VO =15V - - 50 A I CCL IF =16mA, VCC=15V VO=open - 200 - A ICCH(1) Ta=25C, VCC =15V VF =open, IO=0 - 0.02 1.0 A ICCH(2) VCC =15V VO=open, I F =0 - - 2.0 A Ta=25C, I F =16mA - 1.7 1.95 V IF=16mA - -1.9 - mV / C 5.0 - - 60 - - V pF - - 1.0 A Current transfer ratio Logic (0) output voltage Logic (1) output current Logic (0) supply current Logic (1) supply current Input forward voltage VF Input forward voltage temperature coefficient VF / Ta Input reverse voltage Input capacitance *6 Leak current (input-output) *6 Isolation resistance (input-output) *6Capacitance (input-output) Transistor current amplification factor ( Ta=0 to 70C unless otherwise specified ) BV R C IN II-O Conditions Ta=25C, IR=10mA VF =0, f=1MHz Ta=25C, 45%RH, t=5s VI-O=3kVDC R I-O VI-O=500VDC - 10 12 - CI-O f=1MHz - 0.6 - pF h FE VO =5V, IO =3mA - 70 - *5 Current transfer ratio is the ratio of input current and output current expressed in %. *6 Measured as 2-pin element (Short 1, 2, 3, 4 and 5, 6, 7, 8) 6N136 Switching Characteristics Parameter Propagation delay time Output (1) (0) *8 Propagation delay time *9 Output (0) (1) *10 Instantaneous common *11 mode rejection voltage " output (1) " *10 Instantaneous common *11 mode rejection voltage " output (0) " *12 Bandwidth ( Ta=25C, VCC =5V, I F =16mA ) Symbol *8 *9 Conditions MIN. TYP. MAX. Unit t PHL R L =1.9k - 0.3 0.8 s t PLH R L =1.9k - 0.3 0.8 s CM H I F =0, VCM =10VP-P , RL=1.9k - 1.0 - kV/ s CM L VCM =10V P-P , I F =16mA, RL=1.9k - -1.0 - kV/ s - 2.0 - MHz R L =100 BW *8 RL=1.9k is equivalent to one LSTTL and 5.6k pull-up resistor. *10 Instantaneous common mode rejection voltage " output (1) " represents a common mode voltage variation that can hold the output above (1) level (VO>2.0V) Instantaneous common mode rejection voltage " output (0) " represents a common mode voltage variation that can hold the output above (0) level (VO<0.8V) *12 Bandwidth represents a point where AC input gose down by 3dB. *9 Test Circuit for Propagation Delay Time Pulse Generator Pulse input Duty ratio =1/10 IF 0 IF IF monitor 1 8 2 7 3 6 4 5 V CC VO 5V RL 1.5V VO 0.01F 1.5V VOL C L=15pF 100 t PHL t PLH *11 Test Circuit for Instantaneous Common Mode Rejection Voltage 10V IF A B 1 8 2 7 3 6 4 5 VCC=5V 0.01F 90% VCM RL 0V VO V CM + tf CM H IF=0 CM L - 90% tr VO V FF 10% 10% VO 2V 0.8V IF=16mA 5V V OL 6N136 Fig. 2 Power Dissipation vs. Ambient Temperature 30 120 25 100 Power dissipation P, PO (mW) Forward current IF (mA) Fig. 1 Forward Current vs. Ambient Temperature 20 15 10 5 0 -55 0 25 50 75 100 PO 80 60 P 45 40 20 0 -40 125 0 25 50 70 75 100 125 Ambient Temperature Ta (C) Ambient Temperature Ta (C) Fig. 3 Forward Current vs. Forward Voltage Fig. 4 Relative Current Transfer Ratio vs. Forward Current 150 100 Relative current transfer ratio (%) Forward current IF (mA) VCC =5V 10 Ta =0C 1 25C 50C 70C 0.1 0.01 1.0 1.2 1.4 1.6 1.8 2.0 VO =0.4V Ta =25C 100 50 CTR=100% at IF=16mA 0 0.1 2.2 1 Fig. 5 Output Current vs. Output Voltage 110 VCC =5V Relative current transfer ratio (%) Dotted line shows pulse characteristics Ta =25C Output current IO (mA) 16 IF =25mA 14 20mA 12 10 15mA 8 10mA 6 5mA 4 IF =16mA VO =0.4V VCC =5V 100 90 80 70 CTR=100% at Ta=25C 2 0 0 2 4 6 8 10 12 14 Output voltage VO (V) 100 Fig. 6 Relative Current Transfer Ratio vs. Ambient Temperature 20 18 10 Forward current IF (mA) Forward voltage VF (V) 16 18 20 60 -60 -40 -20 0 20 40 60 Ambient Temperature Ta (C) 80 100 6N136 Fig. 7 Propagation Delay Time vs. Ambient Temperature IF =16mA VCC =5V RL=1.9k 0.6 tPHL 0.4 tPLH 0.2 0 -60 -40 -20 0 20 40 60 80 10 -5 10 -6 10 -7 10 -8 10 -9 VCC =V O =5V High level output current IOH (A) Propagation delay time tPHL, tPLH (s) 0.8 Fig. 8 High Level Output Current vs. Ambient Temperature 100 10 -10 10 -11 -60 Ambient Temperature Ta (C) -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Fig. 9 Frequency Response 0 IF =16mA T a =25C Test Circuit for Frequency Characteristic RL =100 -10 15V 220 470 -15 1k 20k AC Input -25 -30 0.2 0.5 1 2 5 100 -20 0.1 1 8 2 7 3 6 4 5 5V 560 Voltage gain AV (dB) -5 RL VO 1.6V DC 0.25V P-PAC 10 Frequency f (MHz) Precaution for use (1) It is recommended that a by-pass capacitor of more than 0.01F be added between VCC and GND near the device in order to stabilize power supply line. (2) Transistor of detector side in bipolar configuration is apt to be affected by static electricity for its minute design. When handling them, general conterplan against static electricity should be taken to avoid breakdown of devices or degradation of characteristics. Application Circuits NOTICE The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii)Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). Contact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. Contact and consult with a SHARP representative if there are any questions about the contents of this publication. 115