( )
OUT ADJ
R
V V I R
2
1.25 1 2
120
æ ö
- = - + + - ´
ç ÷
è ø
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
LM137
,
LM337-N
SNVS778E MAY 1999REVISED JANUARY 2016
LM137, LM337-N 3-Terminal Adjustable Negative Regulators
1 Features 3 Description
The LM137 and LM337-N are adjustable 3-terminal
1 1.5-A Output Current negative voltage regulators capable of supplying
Line Regulation 0.01%/V (Typical) 1.5 A or more currents over an output voltage range
Load Regulation 0.3% (Typical) of 1.25 V to 37 V. It requires only two external
resistors to set the output voltage and one output
77-dB Ripple Rejection capacitor for frequency compensation. The circuit
50 ppm/°C Temperature Coefficient design has been optimized for excellent regulation
Thermal Overload Protection and low thermal transients. Further, the LM137 and
LM337-N feature internal current limiting, thermal
Internal Short-Circuit Current Limiting Protections shutdown and safe-area compensation, making it
virtually blowout-proof against overloads.
2 Applications The LM137 and LM337-N are ideal complements to
Industrial Power Supplies the LM117 and LM317 adjustable positive regulators.
Factory Automation Systems The LM137 has a wider operating temperature range
Building Automation Systems than the LM337-N and is also offered in military and
PLC Systems space qualified versions.
Instrumentation Device Information(1)
IGBT Drive Negative Gate Supplies PART NUMBER PACKAGE BODY SIZE (NOM)
Networking LM137 TO (3) 8.255 mm × 8.255 mm
Set-Top Boxes SOT-223 (4) 3.50 mm × 6.50 mm
LM337-N TO (3) 8.255 mm × 8.255 mm
TO-220 (3) 10.16 mm × 14.986 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet. The LF01 is a lead formed (bent)
version of the TO-220 package.
Adjustable Negative Voltage Regulator
Full output current not available at high input-output voltages
†C1 = 1-μF solid tantalum or 10-μF aluminum electrolytic required for stability
*C2 = 1-μF solid tantalum is required only if regulator is more than 4from power-supply filter capacitor
Output capacitors in the range of 1-μF to 1000-μF of aluminum or tantalum electrolytic are commonly used to provide
improved output impedance and rejection of transients
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM137
,
LM337-N
SNVS778E MAY 1999REVISED JANUARY 2016
www.ti.com
Table of Contents
1 Features.................................................................. 18 Application and Implementation ........................ 12
8.1 Application Information............................................ 12
2 Applications ........................................................... 18.2 Typical Applications ................................................ 12
3 Description............................................................. 19 Power Supply Recommendations...................... 16
4 Revision History..................................................... 210 Layout................................................................... 16
5 Pin Configuration and Functions......................... 310.1 Layout Guidelines ................................................. 16
6 Specifications......................................................... 410.2 Layout Example .................................................... 16
6.1 Absolute Maximum Ratings ...................................... 410.3 Thermal Considerations........................................ 17
6.2 ESD Ratings.............................................................. 411 Device and Documentation Support................. 18
6.3 Recommended Operating Conditions....................... 411.1 Documentation Support ........................................ 18
6.4 Thermal Information.................................................. 411.2 Related Links ........................................................ 18
6.5 Electrical Characteristics........................................... 511.3 Community Resources.......................................... 18
6.6 Typical Characteristics.............................................. 611.4 Trademarks........................................................... 18
7 Detailed Description.............................................. 811.5 Electrostatic Discharge Caution............................ 18
7.1 Overview................................................................... 811.6 Glossary................................................................ 18
7.2 Functional Block Diagram......................................... 812 Mechanical, Packaging, and Orderable
7.3 Feature Description................................................... 8Information ........................................................... 18
7.4 Device Functional Modes........................................ 10
4 Revision History
Changes from Revision D (April 2013) to Revision E Page
Added ESD Ratings table, Feature Description section, Device Functional Modes,Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section.................................................................................................. 1
Deleted soldering information from Absolute Maximum Ratings ........................................................................................... 4
Changes from Revision C (April 2013) to Revision D Page
Changed layout of National Data Sheet to TI format ............................................................................................................. 7
2Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM137 LM337-N
LM137
,
LM337-N
www.ti.com
SNVS778E MAY 1999REVISED JANUARY 2016
5 Pin Configuration and Functions
TO Metal Can Package
TO-220 Plastic Package 3-Pin Package Number NDT0003A
Package Number NDE0003B Bottom View
Front View
SOT-223
3-Lead Package Marked N02A
Front View
Pin Functions
PIN I/O DESCRIPTION
NAME TO-220 TO SOT-223
ADJ 1 1 1 Adjust pin
VIN 2, TAB 3, CASE 2, 4 I Input voltage pin for the regulator
VOUT 3 2 3 O Output voltage pin for the regulator
Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM137 LM337-N
LM137
,
LM337-N
SNVS778E MAY 1999REVISED JANUARY 2016
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings MIN MAX UNIT
Power dissipation Internally Limited
Input-output voltage differential –0.3 40 V
LM137 –55 150
Operating junction temperature LM337-N 0 125 °C
LM337I –40 125
Storage temperature, Tstg –65 150 °C
6.2 ESD Ratings VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Pins listed as ±2000
V may actually have higher performance.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT
LM137 55 150
Operating junction temperature LM337-N 0 125 °C
LM337I 40 125
6.4 Thermal Information LM137 LM337-N
NDT NDT DCY NDE OR NDG
THERMAL METRIC(1) UNIT
(TO) (TO) (SOT-223) (TO-220)
3 PINS 3 PINS 3 PINS 3 PINS
RθJA Junction-to-ambient thermal resistance 140(2) 140(2) 58.3 22.9 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 12 12 36.6 15.7 °C/W
RθJB Junction-to-board thermal resistance 7.2 4.1 °C/W
ψJT Junction-to-top characterization parameter 1.3 2.4 °C/W
ψJB Junction-to-board characterization parameter 7 4.1 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance 1 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
(2) No heat sink.
4Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM137 LM337-N
LM137
,
LM337-N
www.ti.com
SNVS778E MAY 1999REVISED JANUARY 2016
6.5 Electrical Characteristics
Unless otherwise specified, these specifications apply 55°C Tj150°C for the LM137, 0°C Tj125°C for the LM337-N;
VIN VOUT = 5 V; and IOUT = 0.1 A for the TO package and IOUT = 0.5 A for the SOT-223 and TO-220 packages. Although
power dissipation is internally limited, these specifications are applicable for power dissipations of 2 W for the TO and SOT-
223, and 20 W for the TO-220. IMAX is 1.5 A for the SOT-223 and TO-220 packages, and 0.2 A for the TO package.
LM137 LM337-N
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX
TJ= 25°C, 3 V |VIN VOUT|40 V(1)
Line regulation 0.01 0.02 0.01 0.04 %/V
IL= 10 mA
Load regulation TJ= 25°C, 10 mA IOUT IMAX 0.3% 0.5% 0.3% 1%
Thermal regulation TJ= 25°C, 10-ms Pulse 0.002 0.02 0.003 0.04 %/W
Adjustment pin current 65 100 65 100 μA
10 mA ILIMAX
Adjustment pin current charge 3 V |VIN VOUT|40 V, 2 5 2 5 μA
TA= 25°C
TJ= 25°C (2) 1.225 1.25 1.275 1.213 1.25 1.287 V
3 V |VIN VOUT|40 V, (2)
Reference voltage 10 mA IOUT IMAX, P PMAX 55°C TJ150°C 1.2 1.25 1.3 1.2 1.25 1.3 V
Line regulation 3 V |VIN VOUT|40 V, (1) 0.02 0.05 0.02 0.07 %/V
Load regulation 10 mA IOUT IMAX,(1) 0.3% 1% 0.3% 1.5%
Temperature stability TMIN TjTMAX 0.6% 0.6%
|VIN VOUT|40 V 2.5 5 2.5 10 mA
Minimum load current |VIN VOUT|10 V 1.2 3 1.5 6 mA
K, DCY and NDE 1.5 2.2 3.5 1.5 2.2 3.7 A
package
|VIN VOUT|15 V NDT package 0.5 0.8 1.8 0.5 0.8 1.9 A
Current limit K, DCY and NDE 0.24 0.4 0.15 0.4 A
package
|VIN VOUT| = 40 V, TJ= 25°C NDT package 0.15 0.17 0.1 0.17 A
RMS output noise, % of VOUT Tj= 25°C, 10 Hz f10 kHz 0.003% 0.003%
VOUT =10 V, f = 120 Hz 60 60 dB
Ripple rejection ratio CADJ = 10 μF 66 77 66 77 dB
Long-term stability TJ= 125°C, 1000 Hours 0.3% 1% 0.3% 1%
(1) Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to
heating effects are covered under the specification for thermal regulation. Load regulation is measured on the output pin at a point in.
below the base of the TO packages.
(2) Selected devices with tightened tolerance reference voltage available.
Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM137 LM337-N
LM137
,
LM337-N
SNVS778E MAY 1999REVISED JANUARY 2016
www.ti.com
6.6 Typical Characteristics
(NDE Package)
Figure 2. Current Limit
Figure 1. Load Regulation
Figure 3. Adjustment Current Figure 4. Dropout Voltage
Figure 5. Temperature Stability Figure 6. Minimum Operating Current
6Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM137 LM337-N
LM137
,
LM337-N
www.ti.com
SNVS778E MAY 1999REVISED JANUARY 2016
Typical Characteristics (continued)
(NDE Package)
Figure 7. Ripple Rejection Figure 8. Ripple Rejection
Figure 9. Ripple Rejection Figure 10. Output Impedance
Figure 11. Line Transient Response Figure 12. Load Transient Response
Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM137 LM337-N
( )
OUT ADJ
R
V V I R
2
1.25 1 2
120
æ ö
- = - + + - ´
ç ÷
è ø
LM137
,
LM337-N
SNVS778E MAY 1999REVISED JANUARY 2016
www.ti.com
7 Detailed Description
7.1 Overview
In operation, the LM137 and LM337-N develops a nominal 1.25-V reference voltage between the output and
adjustment terminal. The reference voltage is impressed across program resistor R1 (120 Ωfor example) and,
because the voltage is constant, a constant current then flows through the output set resistor R2, giving an
output voltage calculated by Equation 1.
(1)
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 Thermal Regulation
When power is dissipated in an IC, a temperature gradient occurs across the IC chip affecting the individual IC
circuit components. With an IC regulator, this gradient can be especially severe because power dissipation is
large. Thermal regulation is the effect of these temperature gradients on output voltage (in percentage output
change) per Watt of power change in a specified time. Thermal regulation error is independent of electrical
regulation or temperature coefficient, and occurs within 5 ms to 50 ms after a change in power dissipation.
Thermal regulation depends on IC layout as well as electrical design. The thermal regulation of a voltage
regulator is defined as the percentage change of VOUT, per Watt, within the first 10 ms after a step of power is
applied. The LM137 device's specification is 0.02%/W, maximum.
8Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM137 LM337-N
LM137
,
LM337-N
www.ti.com
SNVS778E MAY 1999REVISED JANUARY 2016
Feature Description (continued)
LM137
VOUT =10 V
VIN VOUT =40 V
IIL = 0 A 0.25 A 0 A
Vertical sensitivity, 5 mV/div
Figure 13. Output Drift (10W Pulse for 10ms)
In Figure 13, a typical LM137 device's output drifts only 3 mV (or 0.03% of VOUT =10 V) when a 10-W pulse is
applied for 10 ms. This performance is thus well inside the specification limit of 0.02%/W × 10 W = 0.2%
maximum. When the 10-W pulse is ended, the thermal regulation again shows a 3-mV step at the LM137 chip
cools off.
NOTE
The load regulation error of about 8 mV (0.08%) is additional to the thermal regulation
error.
In Figure 14, when the 10-W pulse is applied for 100 ms, the output drifts only slightly beyond the drift in the first
10 ms, and the thermal error stays well within 0.1% (10 mV).
Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM137 LM337-N
LM137
,
LM337-N
SNVS778E MAY 1999REVISED JANUARY 2016
www.ti.com
Feature Description (continued)
LM137
VOUT =10 V
VIN VOUT =40 V
IL= 0 A 0.25 A 0 A
Horizontal sensitivity, 20 ms/div
Figure 14. Output Drift (10-W Pulse for 100 ms)
7.4 Device Functional Modes
7.4.1 Protection Diodes
When external capacitors are used with any IC regulator, it is sometimes necessary to add protection diodes to
prevent the capacitors from discharging through low current points into the regulator. Most 10-μF capacitors have
low enough internal series resistance to deliver 20-A spikes when shorted. Although the surge is short, there is
enough energy to damage parts of the IC.
When an output capacitor is connected to a negative output regulator and the input is shorted, the output
capacitor pulls current out of the output of the regulator. The current depends on the value of the capacitor, the
output voltage of the regulator, and the rate at which VIN is shorted to ground.
The bypass capacitor on the adjustment terminal can discharge through a low current junction. Discharge occurs
when either the input, or the output, is shorted. Figure 15 shows the placement of the protection diodes.
10 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM137 LM337-N
LM137
,
LM337-N
www.ti.com
SNVS778E MAY 1999REVISED JANUARY 2016
Device Functional Modes (continued)
*When CLis larger than 20 μF, D1 protects the LM137 in case the input supply is shorted
**When C2 is larger than 10 μF and VOUT is larger than 25V, D2 protects the LM137 in case the output is shorted
Figure 15. Regulator With Protection Diodes
Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM137 LM337-N
( )
OUT ADJ
R
V V I R
2
1.25 1 2
120
æ ö
- = - + + - ´
ç ÷
è ø
LM137
,
LM337-N
SNVS778E MAY 1999REVISED JANUARY 2016
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LM137 and LM337-N are versatile, high performance, negative output linear regulators with high accuracy
and a wide temperature range. An output capacitor can be added to further improve transient response, and the
ADJ pin can be bypassed to achieve very high ripple-rejection ratios. The device's functionality can be utilized in
many different applications that require negative voltage supplies, such as bipolar amplifiers, operational
amplifiers, and constant current regulators.
8.2 Typical Applications
8.2.1 Adjustable Negative Voltage Regulator
The LM137 and LM337-N can be used as a simple, negative output regulator to enable a variety of output
voltages needed for demanding applications. By using an adjustable R2 resistor, a variety of negative output
voltages can be made possible as shown in Figure 16.
Full output current not available at high input-output voltages
†C1 = 1-μF solid tantalum or 10-μF aluminum electrolytic required for stability
*C2 = 1-μF solid tantalum is required only if regulator is more than 4 inches from power-supply filter capacitor
Output capacitors in the range of 1 μF to 1000 μF of aluminum or tantalum electrolytic are commonly used to provide
improved output impedance and rejection of transients
Figure 16. Adjustable Negative Voltage Regulator
(2)
8.2.1.1 Design Requirements
The device component count is very minimal, employing two resistors as part of a voltage divider circuit and an
output capacitor for load regulation. An input capacitor is needed if the device is more than 4 inches from the
filter capacitors.
8.2.1.2 Detailed Design Procedure
The output voltage is set based on the selection of the two resistors, R1 and R2, as shown in Figure 16.
12 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM137 LM337-N
LM137
,
LM337-N
www.ti.com
SNVS778E MAY 1999REVISED JANUARY 2016
Typical Applications (continued)
8.2.1.3 Application Curve
As shown in Figure 17, the maximum output current capability is limited by the input-output voltage differential,
package type, and junction temperature.
Figure 17. Current Limit
8.2.2 Adjustable Lab Voltage Regulator
The LM337-N can be combined with a positive regulator such as the LM317-N to provide both a positive and
negative voltage rail. This can be useful in applications that use bi-directional amplifiers and dual-supply
operational amplifiers.
Full output current not available at high input-output voltages
*The 10 μF capacitors are optional to improve ripple rejection
Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM137 LM337-N
*0.8 R1 120W £ £ W
OUT
1.250V
I =
R1
LM137
,
LM337-N
SNVS778E MAY 1999REVISED JANUARY 2016
www.ti.com
Typical Applications (continued)
8.2.3 Current Regulator
A simple, fixed current regulator can be made by placing a resistor between the VOUT and ADJ pins of the
LM137. By regulating a constant 1.25 V between these two terminals, a constant current can be delivered.
(3)
(4)
8.2.4 5.2-V Regulator with Electronic Shutdown
The LM337-N can be used with a PNP transistor to provide shutdown control from a TTL control signal. The PNP
can short or open the ADJ pin to GND. When ADJ is shorted to GND by the PNP, the output is 1.3V. When
ADJ is disconnected from GND by the PNP, then the LM337-N outputs the programmed output of 5.2 V.
Minimum output 1.3 V when control input is low
14 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM137 LM337-N
LM137
,
LM337-N
www.ti.com
SNVS778E MAY 1999REVISED JANUARY 2016
Typical Applications (continued)
8.2.5 High Stability 10-V Regulator
Using a high stability shunt voltage reference in the feedback path, such as the LM329, provides damping
necessary for a stable, low noise output.
Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM137 LM337-N
LM137
,
LM337-N
SNVS778E MAY 1999REVISED JANUARY 2016
www.ti.com
9 Power Supply Recommendations
The input supply to the LM137 and LM337-N must be kept at a voltage level such that its maximum input to
output differential voltage rating is not exceeded. The minimum dropout voltage must also be met with extra
headroom when possible to keep the LM137 and LM337-N in regulation. TI recommends an input capacitor,
especially when the input pin is placed more than 4 inches away from the power-supply filter capacitor.
10 Layout
10.1 Layout Guidelines
Some layout guidelines must be followed to ensure proper regulation of the output voltage with minimum noise.
Traces carrying the load current must be wide to reduce the amount of parasitic trace inductance and the
feedback loop from VOUT to ADJ must be kept as short as possible. To improve PSRR, a bypass capacitor can
be placed at the ADJ pin and must be placed as close as possible to the IC. In cases when VIN shorts to ground,
an external diode must be placed from VIN to VOUT to divert the surge current into the output capacitor and
protect the IC. Similarly, in cases when a large bypass capacitor is placed at the ADJ pin and VOUT shorts to
ground, an external diode must be placed from VOUT to ADJ to provide a path for the bypass capacitor to
discharge. These diodes must be placed close to the corresponding IC pins to increase their effectiveness.
10.2 Layout Example
Figure 18. Layout Example (SOT-223)
16 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM137 LM337-N
LM137
,
LM337-N
www.ti.com
SNVS778E MAY 1999REVISED JANUARY 2016
10.3 Thermal Considerations
10.3.1 Heatsinking SOT-223 Package Parts
The SOT-223 DCY packages use a copper plane on the PCB and the PCB itself as a heatsink. To optimize the
heat sinking ability of the plane and PCB, solder the tab of the package to the plane.
Figure 19 and Figure 20 show the information for the SOT-223 package. Figure 20 assumes a θ(JA) of 75°C/W
for 1 ounce copper and 51°C/W for 2 ounce copper and a maximum junction temperature of 125°C.
Figure 19. θ(JA) vs Copper (2 ounce) Area for the SOT-223 Package
Figure 20. Maximum Power Dissipation vs TAMB for the SOT-223 Package
See AN-1028, SNVA036, for power enhancement techniques to be used with the SOT-223 package.
Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM137 LM337-N
LM137
,
LM337-N
SNVS778E MAY 1999REVISED JANUARY 2016
www.ti.com
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For related documentation see the following:
AN-1028, SNVA036
11.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 1. Related Links
TECHNICAL TOOLS & SUPPORT &
PARTS PRODUCT FOLDER SAMPLE & BUY DOCUMENTS SOFTWARE COMMUNITY
LM137 Click here Click here Click here Click here Click here
LM337-N Click here Click here Click here Click here Click here
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.6 Glossary
SLYZ022 TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
18 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated
Product Folder Links: LM137 LM337-N
PACKAGE OPTION ADDENDUM
www.ti.com 10-Dec-2020
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead finish/
Ball material
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM137H ACTIVE TO NDT 3 500 RoHS & Green AU Level-1-NA-UNLIM -55 to 150 ( LM137HP+, LM137H
P+)
LM137H/NOPB ACTIVE TO NDT 3 500 RoHS & Green AU Level-1-NA-UNLIM -55 to 150 ( LM137HP+, LM137H
P+)
LM337IMP NRND SOT-223 DCY 4 1000 Non-RoHS &
Non-Green Call TI Call TI -40 to 125 N02A
LM337IMP/NOPB ACTIVE SOT-223 DCY 4 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 N02A
LM337IMPX NRND SOT-223 DCY 4 2000 Non-RoHS &
Non-Green Call TI Call TI -40 to 125 N02A
LM337IMPX/NOPB ACTIVE SOT-223 DCY 4 2000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 N02A
LM337T NRND TO-220 NDE 3 45 Non-RoHS &
Non-Green Call TI Call TI 0 to 125 LM337T P+
LM337T/LF01 ACTIVE TO-220 NDG 3 45 RoHS-Exempt
& Green SN Level-3-245C-168 HR 0 to 125 LM337T P+
LM337T/NOPB ACTIVE TO-220 NDE 3 45 RoHS-Exempt
& Green SN Level-1-NA-UNLIM 0 to125 LM337T P+
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
PACKAGE OPTION ADDENDUM
www.ti.com 10-Dec-2020
Addendum-Page 2
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM337IMP SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3
LM337IMP/NOPB SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3
LM337IMPX SOT-223 DCY 4 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3
LM337IMPX/NOPB SOT-223 DCY 4 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Sep-2019
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM337IMP SOT-223 DCY 4 1000 367.0 367.0 35.0
LM337IMP/NOPB SOT-223 DCY 4 1000 367.0 367.0 35.0
LM337IMPX SOT-223 DCY 4 2000 367.0 367.0 35.0
LM337IMPX/NOPB SOT-223 DCY 4 2000 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Sep-2019
Pack Materials-Page 2
MECHANICAL DATA
NDE0003B
www.ti.com
MECHANICAL DATA
MPDS094A – APRIL 2001 – REVISED JUNE 2002
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
DCY (R-PDSO-G4) PLASTIC SMALL-OUTLINE
4202506/B 06/2002
6,30 (0.248)
6,70 (0.264)
2,90 (0.114)
3,10 (0.122)
6,70 (0.264)
7,30 (0.287) 3,70 (0.146)
3,30 (0.130)
0,02 (0.0008)
0,10 (0.0040)
1,50 (0.059)
1,70 (0.067)
0,23 (0.009)
0,35 (0.014)
1 2 3
4
0,66 (0.026)
0,84 (0.033)
1,80 (0.071) MAX
Seating Plane
0°–10°
Gauge Plane
0,75 (0.030) MIN
0,25 (0.010)
0,08 (0.003)
0,10 (0.004) M
2,30 (0.091)
4,60 (0.181) M
0,10 (0.004)
NOTES: A. All linear dimensions are in millimeters (inches).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion.
D. Falls within JEDEC TO-261 Variation AA.
MECHANICAL DATA
NDG0003F
www.ti.com
T03F (Rev B)
MECHANICAL DATA
NDT0003A
www.ti.com
H03A (Rev D)
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated