ADC1175 www.ti.com SNAS012H - JANUARY 2000 - REVISED APRIL 2013 ADC1175 8-Bit, 20MHz, 60mW A/D Converter Check for Samples: ADC1175 FEATURES DESCRIPTION * * * * * The ADC1175 is a low power, 20 Msps analog-todigital converter that digitizes signals to 8 bits while consuming just 60 mW of power (typ). The ADC1175 uses a unique architecture that achieves 7.5 Effective Bits. Output formatting is straight binary coding. 1 2 Internal Sample-and-Hold Function Single +5V Operation Internal Reference Bias Resistors Industry Standard Pinout TRI-STATE Outputs The excellent DC and AC characteristics of this device, together with its low power consumption and +5V single supply operation, make it ideally suited for many video, imaging and communications applications, including use in portable equipment. Furthermore, the ADC1175 is resistant to latch-up and the outputs are short-circuit proof. The top and bottom of the ADC1175's reference ladder is available for connections, enabling a wide range of input possibilities. APPLICATIONS * * * * * Video Digitization Digital Still Cameras Personal Computer Video Cameras CCD Imaging Electro-Optics KEY SPECIFICATIONS * * * * * * Resolution 8Bits Maximum Sampling Frequency 20Msps (min) DNL 0.75 LSB (max) ENOB 7.5 Bits (typ) Ensured No Missing Codes Power Consumption (excluding IREF) 60mW (typ) The ADC1175 is offered in a TSSOP. It is designed to operate over the commercial temperature range of -20C to +75C. PIN CONFIGURATION ADC1175 Pin Configuration TSSOP Package See Package Number PW 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2000-2013, Texas Instruments Incorporated ADC1175 SNAS012H - JANUARY 2000 - REVISED APRIL 2013 www.ti.com BLOCK DIAGRAM Figure 1. PIN DESCRIPTIONS AND EQUIVALENT CIRCUITS Pin No. 2 Symbol 19 VIN 16 VRTS Equivalent Circuit Description Analog signal input. Conversion range is VRB to VRT. Reference Top Bias with internal pull-up resistor. Short this pin to VRT to self bias the reference ladder. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 ADC1175 www.ti.com SNAS012H - JANUARY 2000 - REVISED APRIL 2013 PIN DESCRIPTIONS AND EQUIVALENT CIRCUITS (continued) Pin No. Symbol Equivalent Circuit Description VRT Analog Input that is the high (top) side of the reference ladder of the ADC. Nominal range is 1.0V to AVDD. Voltage on VRT and VRB inputs define the VIN conversion range. Bypass well. See REFERENCE INPUTS for more information. 23 VRB Analog Input that is the low (bottom) side of the reference ladder of the ADC. Nominal range is 0V to 4.0V. Voltage on VRT and VRB inputs define the VIN conversion range. Bypass well. See REFERENCE INPUTS for more information. 22 VRBS Reference Bottom Bias with internal pull down resistor. Short to VRB to self bias the reference ladder. 17 DVDD 1 OE CMOS/TTL compatible Digital input that, when low, enables the digital outputs of the ADC1175. When high, the outputs are in a high impedance state. 1 DVSS Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 3 ADC1175 SNAS012H - JANUARY 2000 - REVISED APRIL 2013 www.ti.com PIN DESCRIPTIONS AND EQUIVALENT CIRCUITS (continued) Pin No. Symbol Equivalent Circuit Description DVDD 12 CMOS/TTL compatible digital clock Input. VIN is sampled on the falling edge of CLK input. CLK 12 DVSS DVDD 3 thru 10 D0-D7 Dn Conversion data digital Output pins. D0 is the LSB, D7 is the MSB. Valid data is output just after the rising edge of the CLK input. These pins are enabled by bringing the OE pin low. DVSS 4 13 DVDD Positive digital supply pin. Connect to a clean voltage source of +5V. AVDD and DVDD should have a common source and be separately bypassed with a 10F capacitor and a 0.1F ceramic chip capacitor. See POWER SUPPLY CONSIDERATIONS for more information. 11 DVDD This digital supply pin supplies power for the digital output drivers. This pin should be connected to a supply source in the range of 2.5V to the Pin 13 potential. 2, 24 DVSS The ground return for the digital supply. AVSS and DVSS should be connected together close to the ADC1175. 14, 15, 18 AVDD Positive analog supply pin. Connected to a quiet voltage source of +5V. AVDD and DVDD should have a common source and be separately bypassed with a 10 F capacitor and a 0.1 F ceramic chip capacitor. See POWER SUPPLY CONSIDERATIONS for more information. 20, 21 AVSS The ground return for the analog supply. AVSS and DVSS should be connected together close to the ADC1175 package. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 ADC1175 www.ti.com SNAS012H - JANUARY 2000 - REVISED APRIL 2013 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ABSOLUTE MAXIMUM RATINGS (1) (2) (3) AVDD, DVDD 6.5V Voltage on Any Pin -0.3V to 6.5V VRT, VRB AVSS to AVDD -0.5 to (AVDD + 0.5V) CLK, OE Voltage Digital Output Voltage Input Current DVSS to DVDD (4) 25mA Package Input Current (4) 50mA Package Dissipation at 25C ESD Susceptibility (6) See Human Body Model 2000V Machine Model 200V Soldering Temp., Infrared, 10 sec. 300C -65C to +150C Storage Temperature (1) (2) (3) (4) (5) (6) (5) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see CONVERTER ELECTRICAL CHARACTERISTICS. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. All voltages are measured with respect to GND = AVSS = DVSS = 0V, unless otherwise specified. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. When the input voltage at any pin exceeds the power supplies (that is, less than AVSS or DVSS, or greater than AVDD or DVDD), the current at that pin should be limited to 25 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 25 mA to two. The absolute maximum junction temperatures (TJmax) for this device is 150C. The maximum allowable power dissipation is dictated by TJmax, the junction-to-ambient thermal resistance JA, and the ambient temperature, TA, and can be calculated using the formula PDMAX = (TJmax - TA )/JA. The values for maximum power dissipation listed above will be reached only when the ADC1175 is operated in a severe fault condition (e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided. Human body model is 100 pF capacitor discharged through a 1.5k resistor. Machine model is 220 pF discharged through ZERO . OPERATING RATINGS (1) (2) -20C TA +75C Operating Temperature Range Supply voltage (AVDD, DVDD) +4.75V to +5.25V AVDD - DVDD <0.5V |AVSS - DVSS| 0V to 100 mV Pin 13 - Pin 11 Voltage <0.5V VRT 1.0V to VDD VRB 0V to 4.0V VRT - VRB 1V to 2.8V VIN Voltage Range VRB to VRT (1) (2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see CONVERTER ELECTRICAL CHARACTERISTICS. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. All voltages are measured with respect to GND = AVSS = DVSS = 0V, unless otherwise specified. PACKAGE THERMAL RESISTANCE Package JA TSSOP-24 92C / W Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 5 ADC1175 SNAS012H - JANUARY 2000 - REVISED APRIL 2013 www.ti.com CONVERTER ELECTRICAL CHARACTERISTICS The following specifications apply for AVDD = DVDD = +5.0VDC, OE = 0V, VRT = +2.6V, VRB = 0.6V, CL = 20 pF, fCLK = 20MHz at 50% duty cycle. Boldface limits apply for TA = TMIN to TMAX; all other limits TA = 25C (1) (2) Symbol Parameter Conditions Typical (3) Limits (3) Units 1.3 LSB ( max) DC Accuracy INL Integral Non Linearity f CLK = 20 MHz 0.5 INL Integral Non Linearity f CLK = 30 MHz 1.0 DNL Differential Non Linearity f CLK = 20 MHz 0.35 DNL Differential Non Linearity f CLK = 30 MHz 1.0 Missing Codes LSB ( max) 0.75 LSB ( max) LSB ( max) 0 (max) EOT Top Offset -24 mV EOB Bottom Offset +37 mV 0.5 Degree 0.4 % Video Accuracy DP Differential Phase Error DG Differential Gain Error fin = 4.43 MHz sine wave fCLK = 17.7 MHz fin = 4.43 MHz sine wave fCLK = 17.7 MHz Analog Input and Reference Characteristics VIN Input Range 2.0 VIN = 1.5V + 0.7Vrms (CLK LOW) 4 (CLK HIGH) 11 VRB V (min) VRT V (max) CIN VIN Input Capacitance RIN RIN Input Resistance >1 M BW Analog Input Bandwidth 120 MHz RRT Top Reference Resistor 360 RREF Reference Ladder Resistance RRB Bottom Reference Resistor VRT to VRB VRT =VRTS,VRB =AVSS Reference Top Self Bias Voltage VRB Reference Bottom Self Bias Voltage VRT connected to VRTS VRB connected to VRBS VRT connected to VRTS VRB connected to VRBS VRT connected to VRTS VRTS VRBS Self Bias Voltage Delta VRB connected to VRBS VRT connected to VRTS VRB connected to AVSS VRT - VRB (1) (2) (3) 6 7 Reference Ladder Current VRT 200 (min) 400 (max) 4.8 mA (min) 9.3 mA (max) 90 VRT =VRTS, VRB =VRBS IREF 300 pF Reference Voltage Delta 8 5.4 mA (min) 10.5 mA (max) 2.6 0.6 2 V 0.55 0.65 V (max) 1.89 V (min) 2.15 V (max) 2.3 2 V (min) V 1.0 V (min) 2.8 V (max) The analog inputs are protected as shown below. Input voltage magnitudes up to 6.5V or to 500 mV below GND will not damage this device. However, errors in the A/D conversion can occur if the input goes above VDD or below GND by more than 50 mV. As an example, if AVDD is 4.75VDC, the full-scale input voltage must be 4.80VDC to ensure accurate conversions. See Figure 2. To ensure accuracy, it is required that AVDD and DVDD be well bypassed. Each supply pin must be decoupled with separate bypass capacitors. Typical figures are at TJ = 25C, and represent most likely parametric norms. Test limits are specified to TI's AOQL (Average Outgoing Quality Level). Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 ADC1175 www.ti.com SNAS012H - JANUARY 2000 - REVISED APRIL 2013 CONVERTER ELECTRICAL CHARACTERISTICS (continued) The following specifications apply for AVDD = DVDD = +5.0VDC, OE = 0V, VRT = +2.6V, VRB = 0.6V, CL = 20 pF, fCLK = 20MHz at 50% duty cycle. Boldface limits apply for TA = TMIN to TMAX; all other limits TA = 25C (1)(2) Symbol Parameter Typical (3) Conditions Limits (3) Units Power Supply Characteristics IADD Analog Supply Current DVDD = AVDD =5.25V 9.5 IDDD Digital Supply Current DVDD = AVDD =5.25V 2.5 DVDD AVDD =5.25V, fCLK = 20 MHz 12 DVDD AVDD =5.25V, fCLK = 30 MHz 13 IAVDD + IDVDD Total Operating Current DVDD = AVDD =5.25V, CLK Low Power Consumption (4) mA mA 17 mA (max) 85 mW (max) 9.6 DVDD = AVDD =5.25V, fCLK = 20 MHz 60 DVDD = AVDD =5.25V, fCLK = 30 MHz 65 mA mW CLK, OE Digital Input Characteristics VIH Logical High Input Voltage DVDD = AVDD = +5.25V 3.0 V (min) VIL Logical Low Input Voltage DVDD = AVDD = +5.25V 1.0 V (max) IIH Logical High Input Current VIH = DVDD = AVDD = +5.25V 5 A IIL Logic Low Input Current VIL = 0V, DVDD = AVDD = +5.25V -5 A CIN Logic Input Capacitance 5 pF Digital Output Characteristics IOH High Level Output Current DVDD = 4.75V, VOH = 2.4V -1.1 mA (max) IOL Low Level Output Current DVDD = 4.75V, VOL = 0.4V 1.6 mA (min) DVDD = 5.25V IOZH, IOZL Tri-State Leakage Current OE = DVDD, VOL 20 A = 0V or VOH = DVDD AC Electrical Characteristics fC1 Maximum Conversion Rate 30 fC2 Minimum Conversion Rate 1 MHz CLK rise to data rising 19.5 ns CLK rise to data falling 16 ns 2.5 Clock Cycles tOD Output Delay Pipeline Delay (Latency) tDS Sampling (Aperture) Delay tAJ Aperture Jitter tOH Output Hold Time tEN OE Low to Data Valid tDIS OE High to High Z State ENOB SINAD SNR (4) Effective Number of Bits Signal-to- Noise & Distortion Signal-to- Noise Ratio CLK low to acquisition of data 20 MHz (min) 3 ns 30 ps rms CLK high to data invalid 10 ns Loaded as in Figure 18 11 ns Loaded as in Figure 18 15 ns fIN = 1.31 MHz, VIN = FS - 2 LSB 7.5 fIN = 4.43 MHz, VIN = FS - 2 LSB 7.3 fIN = 9.9 MHz, VIN = FS - 2 LSB 7.2 fIN = 4.43 MHz, fCLK = 30 MHz 6.5 fIN = 1.31 MHz, VIN = FS - 2 LSB 46.9 fIN = 4.43 MHz, VIN = FS - 2 LSB 45.7 fIN = 9.9 MHz, VIN = FS - 2 LSB 45.1 fIN = 4.43 MHz, fCLK = 30 MHz 40.9 fIN = 1.31 MHz, VIN = FS - 2 LSB 47.6 fIN = 4.43 MHz, VIN = FS - 2 LSB 46 fIN = 9.9 MHz, VIN = FS - 2 LSB 46.1 fIN = 4.43 MHz, fCLK = 30 MHz 42.1 7.0 43 44 Bits (min) dB (min) dB (min) At least two clock cycles must be presented to the ADC1175 after power up. See THE ADC1175 CLOCK for details. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 7 ADC1175 SNAS012H - JANUARY 2000 - REVISED APRIL 2013 www.ti.com CONVERTER ELECTRICAL CHARACTERISTICS (continued) The following specifications apply for AVDD = DVDD = +5.0VDC, OE = 0V, VRT = +2.6V, VRB = 0.6V, CL = 20 pF, fCLK = 20MHz at 50% duty cycle. Boldface limits apply for TA = TMIN to TMAX; all other limits TA = 25C (1)(2) Symbol SFDR THD Parameter Spurious Free Dynamic Range Total Harmonic Distortion Conditions Typical (3) fIN = 1.31 MHz, VIN = FS - 2 LSB 56 fIN = 4.43 MHz, VIN = FS - 2 LSB 58 fIN = 9.9 MHz, VIN = FS - 2 LSB 53 fIN = 4.43 MHz, fCLK = 30 MHz 47 fIN = 1.31 MHz, VIN = FS - 2 LSB -55 fIN = 4.43 MHz, VIN = FS - 2 LSB -57 fIN = 9.9 MHz, VIN = FS - 2 LSB -52 fIN = 4.43 MHz, fCLK = 30 MHz -47 Limits (3) Units dB dB Figure 2. 8 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 ADC1175 www.ti.com SNAS012H - JANUARY 2000 - REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS INL vs. Temp at fCLK DNL vs. Temp at fCLK Figure 3. Figure 4. SNR vs. Temp at fCLK SNR vs. Temp at fCLK Figure 5. Figure 6. THD vs. Temp THD vs. Temp Figure 7. Figure 8. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 9 ADC1175 SNAS012H - JANUARY 2000 - REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) 10 SINAD/ENOB vs. Temp SINAD/ENOB vs. Temp Figure 9. Figure 10. SINAD and ENOB vs. Clock Duty Cycle SFDR vs. Temp and fIN Figure 11. Figure 12. SFDR vs. Temp and fIN Differential Gain vs. Temperature Figure 13. Figure 14. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 ADC1175 www.ti.com SNAS012H - JANUARY 2000 - REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Differential Phase vs. Temperature Spectral Response at fCLK = 20 MSPS Figure 15. Figure 16. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 11 ADC1175 SNAS012H - JANUARY 2000 - REVISED APRIL 2013 www.ti.com SPECIFICATION DEFINITIONS ANALOG INPUT BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental drops 3 dB below its low frequency value for a full scale input. The test is performed with fIN equal to 100 kHz plus integer multiples of fCLK. The input frequency at which the output is -3 dB relative to the low frequency input signal is the full power bandwidth. APERTURE JITTER is the time uncertainty of the sampling point (tDS), or the range of variation in the sampling delay. BOTTOM OFFSET is the difference between the input voltage that just causes the output code to transition to the first code and the negative reference voltage. Bottom offset is defined as EOB = VZT - VRB, where VZT is the first code transition input voltage. Note that this is different from the normal Zero Scale Error. DIFFERENTIAL GAIN ERROR is the percentage difference between the output amplitudes of a high frequency reconstructed sine wave at two different d.c. levels. DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1 LSB. DIFFERENTIAL PHASE ERROR is the difference in the output phase of a reconstructed small signal sine wave at two different d.c. levels. EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise and Distortion Ratio, or SINAD. ENOB is defined as (SINAD - 1.76) / 6.02 and says that the converter is equivalent to a perfect ADC of this (ENOB) number of bits. INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from zero scale (1/2LSB below the first code transition) through positive full scale (1/2LSB above the last code transition). The deviation of any given code from this straight line is measured from the center of that code value. The end point test method is used. OUTPUT DELAY is the time delay after the rising edge of the input clock before the data update is present at the output pins. OUTPUT HOLD TIME is the length of time that the output data is valid after the rise of the input clock. PIPELINE DELAY (LATENCY) is the number of clock cycles between initiation of conversion and when that data is presented to the output stage. Data for any give sample is available the Pipeline Delay plus the Output Delay after that sample is taken. New data is available at every clock cycle, but the data lags the conversion by the pipeline delay. SAMPLING (APERTURE) DELAY is that time required after the fall of the clock input for the sampling switch to open. The Sample/Hold circuit effectively stops capturing the input signal and goes into the "hold" mode tDS after the clock goes low. SIGNAL TO NOISE RATIO (SNR) is the ratio of the rms value of the input signal to the rms value of the other spectral components below one-half the sampling frequency, not including harmonics or d.c. SIGNAL TO NOISE PLUS DISTORTION (S/(N+D) or SINAD) is the ratio of the rms value of the input signal to the rms value of all of the other spectral components below half the clock frequency, including harmonics but excluding d.c. SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the rms values of the input signal and the peak spurious signal, where a spurious signal is any signal present in the output spectrum that is not present at the input. TOP OFFSET is the difference between the positive reference voltage and the input voltage that just causes the output code to transition to full scale and is defined as EOT = VFT - VRT. Where VFT is the full scale transition input voltage. Note that this is different from the normal Full Scale Error. TOTAL HARMONIC DISTORTION (THD) is the ratio of the rms total of the first six harmonic components, to the rms value of the input signal. 12 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 ADC1175 www.ti.com SNAS012H - JANUARY 2000 - REVISED APRIL 2013 TIMING DIAGRAM Figure 17. ADC1175 Timing Diagram Figure 18. tEN , tDIS Test Circuit Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 13 ADC1175 SNAS012H - JANUARY 2000 - REVISED APRIL 2013 www.ti.com FUNCTIONAL DESCRIPTION The ADC1175 uses a new, unique architecture to achieve 7.2 effective bits at and maintains superior dynamic performance up to 1/2 the clock frequency. The analog signal at VIN that is within the voltage range set by VRT and VRB are digitized to eight bits at up to 30 MSPS. Input voltages below VRB will cause the output word to consist of all zeroes. Input voltages above VRT will cause the output word to consist of all ones. VRT has a range of 1.0 Volt to the analog supply voltage, AVDD, while VRB has a range of 0 to 4.0 Volts. VRT should always be between 1.0 Volt and 2.8 Volts more positive than VRB. If VRT and VRTS are connected together and VRB and VRBS are connected together, the nominal values of VRT and VRB are 2.6V and 0.6V, respectively. If VRT and VRTS are connected together and VRB is grounded, the nominal value of VRT is 2.3V. Data is acquired at the falling edge of the clock and the digital equivalent of the data is available at the digital outputs 2.5 clock cycles plus tOD later. The ADC1175 will convert as long as the clock signal is present at pin 12. The Output Enable pin OE, when low, enables the output pins. The digital outputs are in the high impedance state when the OE pin is high. 14 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 ADC1175 www.ti.com SNAS012H - JANUARY 2000 - REVISED APRIL 2013 APPLICATIONS INFORMATION THE ANALOG INPUT The analog input of the ADC1175 is a switch followed by an integrator. The input capacitance changes with the clock level, appearing as 4 pF when the clock is low, and 11 pF when the clock is high. Since a dynamic capacitance is more difficult to drive than a fixed capacitance, choose an amplifier that can drive this type of load. The LMH6702, LMH6609, LM6152, LM6154, LM6181 and LM6182 have been found to be excellent devices for driving the ADC1175. Do not drive the input beyond the supply rails. Figure 19 shows an example of an input circuit using the LMH6702. Driving the analog input with input signals up to 2.8 VP-P will result in normal behavior where signals above VRT will result in a code of FFh and input voltages below VRB will result in an output code of zero. Input signals above 2.8 VP-P may result in odd behavior where the output code is not FFh when the input exceeds VRT. REFERENCE INPUTS The reference inputs VRT (Reference Top) and VRB (Reference Bottom) are the top and bottom of the reference ladder. Input signals between these two voltages will be digitized to 8 bits. External voltages applied to the reference input pins should be within the range specified in Operating Ratings (1.0V to AVDD for VRT and 0V to (AVDD - 1.0V) for VRB). Any device used to drive the reference pins should be able to source sufficient current into the VRT pin and sink sufficient current from the VRB pin. The reference ladder can be self-biased by connecting VRT to VRTS and connecting VRB to VRBS to provide top and bottom reference voltages of approximately 2.6V and 0.6V, respectively, with VCC = 5.0V. This connection is shown in Figure 19. If VRT and VRTS are tied together, but VRB is tied to analog ground, a top reference voltage of approximately 2.3V is generated. The top and bottom of the ladder should be bypassed with 10F tantalum capacitors located close to the reference pins. The reference self-bias circuit of Figure 19 is very simple and performance is adequate for many applications. Superior performance can generally be achieved by driving the reference pins with a low impedance source. By forcing a little current into or out of the top and bottom of the ladder, as shown in Figure 20, the top and bottom reference voltages can be trimmed and performance improved over the self-bias method of Figure 19. The resistive divider at the amplifier inputs can be replaced with potentiometers. The LMC662 amplifier shown was chosen for its low offset voltage and low cost. Note that a negative power supply is needed for these amplifiers if their outputs are required to go slightly negative to force the required reference voltages. If reference voltages are desired that are more than a few tens of millivolts from the self-bias values, the circuit of Figure 21 will allow forcing the reference voltages to whatever levels are desired. This circuit provides the best performance because of the low source impedance of the transistors. Note that the VRTS and VRBS pins are left floating. VRT can be anywhere between VRB + 1.0V and the analog supply voltage, and VRB can be anywhere between ground and 1.0V below VRT. To minimize noise effects and ensure accurate conversions, the total reference voltage range (VRT - VRB) should be a minimum of 1.0V and a maximum of about 2.8V. If VRB is not required to be below about +700mV, the -5V points in Figure 21 can be returned to ground and the negative supply eliminated. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 15 ADC1175 SNAS012H - JANUARY 2000 - REVISED APRIL 2013 www.ti.com +5V Choke 150, 1% 0.1 PF 237, 1% 57.6, 1% 10 PF 237, 1% 2 Analog Input + + 10 PF 3 + 150 1% 6 110 14 15 18 11 13 AVDD 19 0.1 PF DVDD to AVDD 62 pF LMH6702 16 17 VRTS VRT 10 PF ADC1175 23 22 D7 D6 D5 D4 D3 D2 D1 D0 10 9 8 7 6 5 4 3 VRB VRBS 10 PF OE to AVSS AVSS 20 21 DVSS 2 24 1 CLK 12 Because of resistor tolerances, the reference voltages can vary by as much as 6%. Choose an amplifier that can drive a dynamic capacitance (see text). Figure 19. Simple, Low Component Count, Self-Bias Reference Application 16 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 ADC1175 www.ti.com SNAS012H - JANUARY 2000 - REVISED APRIL 2013 Self-bias is still used, but the reference voltages are trimmed by providing a small trim current with the operational amplifiers. Figure 20. Better Defining the ADC Reference Voltage Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 17 ADC1175 SNAS012H - JANUARY 2000 - REVISED APRIL 2013 www.ti.com Driving the reference to force desired values requires driving with a low impedance source, provided by the transistors. Pins 16 and 22 are not connected. Figure 21. POWER SUPPLY CONSIDERATIONS Many A/D converters draw sufficient transient current to corrupt their own power supplies if not adequately bypassed. A 10F tantalum or aluminum electrolytic capacitor should be placed within an inch (2.5 centimeters) of the A/D power pins, with a 0.1 F ceramic chip capacitor placed as close as possible to the converter's power supply pins. Leadless chip capacitors are preferred because they have low lead inductance. While a single voltage source should be used for the analog and digital supplies of the ADC1175, these supply pins should be well isolated from each other to prevent any digital noise from being coupled to the analog power pins. A wideband choke, such as the JW Miller FB20010-3B, is recommended between the analog and digital supply lines, with a ceramic capacitor close to the analog supply pin. Avoid inductive components in the analog supply line. The converter digital supply should not be the supply that is used for other digital circuitry on the board. It should be the same supply used for the A/D analog supply. As is the case with all high speed converters, the ADC1175 should be assumed to have little a.c. power supply rejection, especially when self-biasing is used by connecting VRT and VRTS together. 18 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 ADC1175 www.ti.com SNAS012H - JANUARY 2000 - REVISED APRIL 2013 No pin should ever have a voltage on it that is in excess of the supply voltages or below ground, not even on a transient basis. This can be a problem upon application of power to a circuit. Be sure that the supplies to circuits driving the CLK, OE, analog input and reference pins do not come up any faster than does the voltage at the ADC1175 power pins. Pins 11 and 13 are both labeled DVDD. Pin 11 is the supply point for the digital core of the ADC, where pin 13 is used only to provide power to the ADC output drivers. As such, pin 11 may be connected to a voltage source that is less than the +5V used for AVDD and DVDD to ease interfacing to low voltage devices. Pin 11 should never exceed the pin 13 potential by more than 0.5V. THE ADC1175 CLOCK Although the ADC1175 is tested and its performance is ensured with a 20MHz clock, it typically will function with clock frequencies from 1MHz to 30MHz. If continuous conversions are not required, power consumption can be reduced somewhat by stopping the clock at a logic low when the ADC1175 is not being used. This reduces the current drain in the ADC1175's digital circuitry from a typical value of 2.5mA to about 100A. Note that powering up the ADC1175 without the clock running may not save power, as it will result in an increased current flow (by as much as 170%) in the reference ladder. In some cases, this may increase the ladder current above the specified limit. Toggling the clock twice at 1MHz or higher and returning it to the low state will eliminate the excess ladder current. An alternative power-saving technique is to power up the ADC1175 with the clock active, then halt the clock in the low state after two or more clock cycles. Stopping the clock in the high state is not recommended as a power-saving technique. LAYOUT AND GROUNDING Proper grounding and proper routing of all signals is essential to ensure accurate conversion. Separate analog and digital ground planes that are connected beneath the ADC1175 may be used, but best EMI practices require a single ground plane. However, it is important to keep analog signal lines away from digital signal lines and away from power supply currents. This latter requirement requires the careful separation and placement of power planes. The use of power traces rather than one or more power planes is not recommended as higher frequencies are not well filtered with lumped capacitances. To filter higher frequency noise components it is necessary to have sufficient capacitance between the power and ground planes. If separate analog and digital ground planes are used, the analog and digital grounds may be in the same layer, but should be separated from each other. If separate analog and digital ground layers are used, they should never overlap each other. Capacitive coupling between a typically noisy digital ground plane and the sensitive analog circuitry can lead to poor performance that may seem impossible to isolate and remedy. The solution is to keep the analog circuity well separated from the digital circuitry. Digital circuits create substantial supply and ground current transients. The logic noise thus generated could have significant impact upon system noise performance. The best logic family to use in systems with A/D converters is one which employs non-saturating transistor designs, or has low noise characteristics, such as the 74HC(T) and 74AC(T)Q families. The worst noise generators are logic families that draw the largest supply current transients during clock or signal edges, like the 74F and the 74AC(T) families. In general, slower logic families will produce less high frequency noise than do high speed logic families. Since digital switching transients are composed largely of high frequency components, total ground plane copper weight will have little effect upon the logic-generated noise. This is because of the skin effect. Total surface area is more important than is total ground plane volume. An effective way to control ground noise is by using a single, solid ground plane, splitting the power plane into analog and digital areas and having power and ground planes in adjacent board layers. There should be no traces within either the power or the ground layers of the board. The analog and digital power planes should reside in the same board layer so that they can not overlap each other. The analog and digital power planes define the analog and digital areas of the board. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 19 ADC1175 SNAS012H - JANUARY 2000 - REVISED APRIL 2013 www.ti.com Generally, analog and digital lines should cross each other at 90 degrees to avoid getting digital noise into the analog path. In high frequency systems, however, avoid crossing analog and digital lines altogether. Clock lines should be isolated from ALL other lines, analog and digital. Even the generally accepted 90 degree crossing should be avoided as even a little coupling can cause problems at high frequencies. Best performance at high frequencies and at high resolution is obtained with a straight signal path. Be especially careful with the layout of inductors. Mutual inductance can change the characteristics of the circuit in which they are used. Inductors should not be placed side by side, not even with just a small part of their bodies being beside each other. The analog input should be isolated from noisy signal traces to avoid coupling of spurious signals into the input. Any external component (e.g., a filter capacitor) connected between the converter's input and ground should be connected to a very clean point in the ground return. DYNAMIC PERFORMANCE The ADC1175 is a.c. tested and its dynamic performance is ensured. To meet the published specifications, the clock source driving the CLK input must be free of jitter. For best a.c. performance, isolating the ADC clock from any digital circuitry should be done with adequate buffers, as with a clock tree. See Figure 22. Figure 22. Isolating the ADC clock from Digital Circuitry. It is good practice to keep the ADC clock line as short as possible and to keep it well away from any other signals. Other signals can introduce jitter into the clock signal. COMMON APPLICATION PITFALLS Driving the inputs (analog or digital) beyond the power supply rails. For proper operation, all inputs should not go more than 50mV below the ground pins or 50mV above the supply pins. Exceeding these limits on even a transient basis can cause faulty or erratic operation. It is not uncommon for high speed digital circuits to exhibit undershoot that goes more than a volt below ground due to improper line termination. A resistor of 50 to 100 in series with the offending digital input, located close to the signal source, will usually eliminate the problem. Care should be taken not to overdrive the inputs of the ADC1175. Such practice may lead to conversion inaccuracies and even to device damage. Attempting to drive a high capacitance digital data bus. The more capacitance the output drivers must charge for each conversion, the more instantaneous digital current is required from DVDD and DGND. These large charging current spikes can couple into the analog section, degrading dynamic performance. Buffering the digital data outputs (with an 74AC541, for example) may be necessary if the data bus to be driven is heavily loaded. Dynamic performance can also be improved by adding 47 to 100 series resistors at each digital output, reducing the energy coupled back into the converter output pins. Using an inadequate amplifier to drive the analog input. As explained in THE ANALOG INPUT, the capacitance seen at the input alternates between 4 pF and 11 pF with the clock. This dynamic capacitance is more difficult to drive than is a fixed capacitance, and should be considered when choosing a driving device. The LMH6702, LMH6609, LM6152, LM6154, LM6181 and LM6182 have been found to be excellent devices for driving the ADC1175 analog input. 20 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 ADC1175 www.ti.com SNAS012H - JANUARY 2000 - REVISED APRIL 2013 Driving the VRT pin or the VRB pin with devices that can not source or sink the current required by the ladder. As mentioned in REFERENCE INPUTS, care should be taken to see that any driving devices can source sufficient current into the VRT pin and sink sufficient current from the VRB pin. If these pins are not driven with devices than can handle the required current, these reference pins will not be stable, resulting in a reduction of dynamic performance. Using a clock source with excessive jitter, using an excessively long clock signal trace, or having other signals coupled to the clock signal trace. This will cause the sampling interval to vary, causing excessive output noise and a reduction in SNR performance. Simple gates with RC timing is generally inadequate as a clock source. Input test signal contains harmonic distortion that interferes with the measurement of dynamic signal to noise ratio. Harmonic and other interfering signals can be removed by inserting a filter at the signal input. Suitable filters are shown in Figure 23 and Figure 24. The circuit of Figure 23 has cutoff of about 5.5 MHz and is suitable for input frequencies of 1 MHz to 5 MHz. The circuit of Figure 24 has a cutoff of about 11 MHz and is suitable for input frequencies of 5 MHz to 10 MHz. These filters should be driven by a generator of 75 Ohm source impedance and terminated with a 75 ohm resistor. Figure 23. 5.5 MHz Low Pass Filter to Eliminate Harmonics at the Signal Input Use at input frequencies of 5 MHz to 10 MHz. Figure 24. 11 MHz Low Pass Filter to Eliminate Harmonics at the Signal Input Not considering the effect on a driven CMOS digital circuit(s) when the ADC1175 is in the power down mode. Because the ADC1175 output goes into a high impedance state when in the power down mode, any CMOS device connected to these outputs will have their inputs floating when the ADC is in power down. Should the inputs of the circuit being driven by the ADC digital outputs float to a level near 2.5V, a CMOS device could exhibit relative large supply currents as the input stage toggles rapidly. The solution is to use pull-down resistors at the ADC outputs. The value of these resistors is not critical, as long as they do not cause excessive currents in the outputs of the ADC1175. Low pull-down resistor values could result in degraded SNR and SINAD performance of the ADC1175. Values between 5 k and 100 k should work well. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 21 ADC1175 SNAS012H - JANUARY 2000 - REVISED APRIL 2013 www.ti.com REVISION HISTORY Changes from Revision G (April 2013) to Revision H * 22 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 21 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: ADC1175 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) (6) ADC1175CIMTC/NOPB ACTIVE TSSOP PW 24 61 RoHS & Green SN Level-1-260C-UNLIM -20 to 75 ADC1175 CIMTC ADC1175CIMTCX/NOPB ACTIVE TSSOP PW 24 2500 RoHS & Green SN Level-1-260C-UNLIM -20 to 75 ADC1175 CIMTC (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing ADC1175CIMTCX/NOPB TSSOP PW 24 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 16.4 Pack Materials-Page 1 6.95 B0 (mm) K0 (mm) P1 (mm) 8.3 1.6 8.0 W Pin1 (mm) Quadrant 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) ADC1175CIMTCX/NOPB TSSOP PW 24 2500 367.0 367.0 35.0 Pack Materials-Page 2 PACKAGE OUTLINE PW0024A TSSOP - 1.2 mm max height SCALE 2.000 SMALL OUTLINE PACKAGE SEATING PLANE C 6.6 TYP 6.2 A 0.1 C PIN 1 INDEX AREA 22X 0.65 24 1 2X 7.15 7.9 7.7 NOTE 3 12 13 B 0.30 0.19 0.1 C A B 24X 4.5 4.3 NOTE 4 1.2 MAX 0.25 GAGE PLANE 0.15 0.05 (0.15) TYP SEE DETAIL A 0 -8 0.75 0.50 DETAIL A A 20 TYPICAL 4220208/A 02/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per side. 4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side. 5. Reference JEDEC registration MO-153. www.ti.com EXAMPLE BOARD LAYOUT PW0024A TSSOP - 1.2 mm max height SMALL OUTLINE PACKAGE SYMM 24X (1.5) (R0.05) TYP 1 24 24X (0.45) 22X (0.65) SYMM 13 12 (5.8) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE: 10X SOLDER MASK OPENING SOLDER MASK OPENING METAL UNDER SOLDER MASK METAL EXPOSED METAL EXPOSED METAL 0.05 MAX ALL AROUND NON-SOLDER MASK DEFINED (PREFERRED) 0.05 MIN ALL AROUND SOLDER MASK DEFINED SOLDER MASK DETAILS 15.000 4220208/A 02/2017 NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN PW0024A TSSOP - 1.2 mm max height SMALL OUTLINE PACKAGE 24X (1.5) SYMM (R0.05) TYP 1 24 24X (0.45) 22X (0.65) SYMM 12 13 (5.8) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE: 10X 4220208/A 02/2017 NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES "AS IS" AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI's products are provided subject to TI's Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI's provision of these resources does not expand or otherwise alter TI's applicable warranties or warranty disclaimers for TI products. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2020, Texas Instruments Incorporated