Home EC2 Robison Electronics Cornucopia Contact Us PULSE GENERATOR MODULES Background Passive Delay Lines Active Delay Lines Digital Modules Frequency Multiplier Modules Pulse Generator Modules Noise Filter Modules Square Wave Generator Modules Encoder/Decoder Modules Inductors Hall-Effect Sensors PDF Catalogs Technical Info Search Products Made in U.S.A. MDFDPGM-TTL-XX-XXX Mini DIP FAST TTL Delayed Pulse Generator Module - TL FAST input and outputs - Pulse widths stable and precise - 8-pin DIP package - Leads - Thru-hole, J, Gull Wing or Tucked - Available in pulse widths from 5 to 90ns - 10 TL fan-out capacity DESIGN NOTES The "Mini Dip Series" Delayed Pulse Generator Modules developed by Engineered Components Company have been designed to provide precise output pulse widths at specified delay times after input trigger when triggered by variable width inputs. All required driving and output circuitry, as well as timing components, are contained in an 8-pin DIP package. These pulse generator modules are of hybrid construction utilizing the proven technologies of active integrated circuitry and of passive networks utilizing capacitive, inductive and resistive elements. The MTBF on these modules, when calculated per MIL-HDBK-217 for a 50C ground fixed environment, is in excess of 3 million hours. These modules are compatible with TL FAST circuits and require no external components in order to obtain the specified output pulse. [Top] The MDFDPGM-TTL is available in 19 pulse widths and 19 time delays from 5 to 90ns. These modules provide a stable TL output pulse of the specified width and at the specified time for each positive input step. It is necessary only that the input step be held positive for at least 10ns in order to obtain the desired output pulse. The duration of the positive input pulse, after this time, has no effect on the output pulse width. No output pulse will occur on the negative input pulse transition. Time between trigger inputs must be a minimum of twice the sum of the delay time and output pulse width specified. Both pulse width and delay time tolerance are maintained as shown in the accompanying Part Number Table, when tested under the "Test Conditions" shown. Pulse width is measured at the +1.5V level on both leading and trailing edges. Rise and fall times are less than 3ns, when measured from .8V to 2.0V. These modules are capable of driving 10 TL loads. Temperature coefficient of delay is approxima tely +800ppm/C and of pulse width is approximately -800ppm/C over the operating temperature range of 0 to +70C. These "Mini DIP Series" modules are packaged in an 8-pin DIP housing, molded of flame-proof Diallyl Phthalate per ASTM D 5948, Type SDG-F, and are fully encapsulated in epoxy resin. Thru-hole, J, Gull Wing or Tucked Lead configurations are available on these modules (see Part Number Table note to specify). Leads meet the solderability requirements of MIL-STD-202, Method 208. Corner standoffs on the housing of the thruhole lead version and lead design of the surface mount versions provide positive standoff from the printed circuit board to permit solder-fillet formation and flush cleaning of solderflux residues for improved reliability. Marking consists of manufacturer's logo (EC), part number, pin one (1) identification and date code of manufacture. All marking is applied by silk screen process using white epoxy paint in accordance with MIL-STD-130, to meet the permanency of identification required by MIL-STD-202, Method 215. TEST CONDITIONS 1. All measurements are made at 25C. 2. Vcc supply voltage is maintained at 5.0V DC. 3. All units are tested using a FAST toggle-type positive input pulse and one FAST TL load at the output. 4. Input pulse width used is 10ns for all modules; repetition rate is approximately 200kHz. OPERATING SPECIFICATIONS *Vcc supply voltage:........... Vcc supply current: Constant "0" in............. Constant "1" in............. Logic 1 Input: Voltage .................... Current .................... 4.75 to 5.25V DC 30mA typical 30mA typical 2V min.; Vcc max. 2.7V = 20uA max. 5.5V = 1mA max. Logic 0 Input: Voltage..................... Current..................... Logic 1 Voltage out:........... Logic 0 Voltage out:........... Operating temperature range:... Storage temperature:........... 0.8V max. -0.6mA max. 2.7V min. 0.5V max. 0 to 70C. -55 to +125C. *Delay increases or decreases approximately 2% for a respective increase or decrease of 5% in supply voltage. Pulse width increases or decreases approximately 2% for a respective decrease or increase of 5% in supply voltage. PART NUMBER TABLE Suffix Part Number with G (for Gull Wing Lead), J (for J Lead), F (for Thru-hole Lead) or T (for Tucked Lead). Examples: MDFDPGM-TTL-10G (Gull Wing), MDFDPGM-TTL-25J (J Lead), MDFDPGMTTL-70F (Thru-hole Lead) or MDFDPGM-TTL-100T (Tucked Lead). Part Number MDFDPGM-TTL- _ _ -5 MDFDPGM-TTL- _ _ -6 MDFDPGM-TTL- _ _ -7 MDFDPGM-TTL- _ _ -8 MDFDPGM-TTL- _ _ -9 MDFDPGM-TTL- _ _ -10 MDFDPGM-TTL- _ _ -15 MDFDPGM-TTL- _ _ -20 MDFDPGM-TTL- _ _ -25 MDFDPGM-TTL- _ _ -30 MDFDPGM-TTL- _ _ -35 MDFDPGM-TTL- _ _ -40 MDFDPGM-TTL- _ _ -45 MDFDPGM-TTL- _ _ -50 MDFDPGM-TTL- _ _ -60 MDFDPGM-TTL- _ _ -70 MDFDPGM-TTL- _ _ -75 MDFDPGM-TTL- _ _ -80 MDFDPGM-TTL- _ _ -90 Pulse Width (in ns) 5 1 6 1 7 1 8 1 9 1 10 1 15 1 20 1 25 1 30 1 35 1.5 40 1.5 45 1.5 50 1.5 60 1.5 70 2 75 2 80 2 90 3 Complete part number includes desired delay time (in ns) from input trigger to beginning of output pulse followed by a dash, the desired pulse width and then the lead style (F, G, J, or T). Delay times are available in the same delays as shown above for pulse widths (from 6 to 90ns), e.g., part number MDFDPGM-TTL-25-10F has a delay of 25ns with a 10ns pulse and MDFPGM-TTL-8-30J has a delay of 8ns with a 30ns pulse width. Special modules can be readily manufactured to improve accuracies and/or provide customer specified pulse widths for specific applications. :: Site C re ate d by KLM De signs :: (c) Copyright 2011, Cornucopia Tool & Plastics, Inc. All Rights Reserved.