ST25TV-eSEAL Discovery board for the ST25TV02K NFC Forum Type 5 tag IC Data brief Features * Ready-to-use printed circuit board including - ST25TV02K NFC/RFID tag in UFDFPN5 ECOPACK2(R) package - Class 3, single layer inductive antenna etched on the PCB - Tamper detect capability - TruST25TM digital signature * Contactless interface - RF link based on ISO/IEC 15693 - NFC Forum Type 5 - Internal 23.5 pF tuning capacitance Description The ST25TV-eSEAL is a ready-to-use demonstration board allowing the user to assess the features and capabilities of the ST25TV series NFC tags. To demonstrate the tamper detect function, the ST25TV-eSEAL can be used in conjunction with the DEMO-CR95HF-A demonstration board, or with an AndroidTM smart-phone. June 2018 DB3596 Rev 1 For further information contact your local STMicroelectronics sales office. 1/6 www.st.com Block diagram 1 ST25TV-eSEAL Block diagram Figure 1. Functional block diagram $& &ODVV DQWHQQDORRS 7' 6779. $& 7' 069 2/6 DB3596 Rev 1 ST25TV-eSEAL Formal notices required by the U.S. Federal Communications Commission 2 Formal notices required by the U.S. Federal Communications Commission ("FCC") 2.1 FCC Compliance Statement 2.1.1 Part 15.19 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2.1.2 Part 15.105 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 2.1.3 Part 15.21 Any changes or modifications to this equipment not expressly approved by STMicroelectronics may cause harmful interference and void the user's authority to operate this equipment. DB3596 Rev 1 3/6 6 Formal notices required by the Industry Canada ("IC") ST25TV-eSEAL 3 Formal notices required by the Industry Canada ("IC") 3.1 Compliance Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. 3.2 Declaration de Conformite Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. 4/6 DB3596 Rev 1 ST25TV-eSEAL 4 Revision history Revision history Table 1. Document revision history Date Revision 06-June-2018 1 Changes Initial release. DB3596 Rev 1 5/6 6 ST25TV-eSEAL IMPORTANT NOTICE - PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST's terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers' products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. (c) 2018 STMicroelectronics - All rights reserved 6/6 DB3596 Rev 1