For further information contact your local STMicroelectronics sales office.
June 2018 DB3596 Rev 1 1/6
ST25TV-eSEAL
Discovery board for the ST25TV02K NFC Forum Type 5 tag IC
Data brief
Features
•Ready-to-use printed circuit board including
– ST25TV02K NFC/RFID tag in UFDFPN5
ECOPACK2® package
– Class 3, single layer inductive antenna
etched on the PCB
– Tamper detect capability
– TruST25™ digital signature
•Contactless interface
– RF link based on ISO/IEC 15693
– NFC Forum Type 5
– Internal 23.5 pF tuning capacitance
Description
The ST25TV-eSEAL is a ready-to-use
demonstration board allowing the user to assess
the features and capabilities of the ST25TV series
NFC tags.
To demonstrate the tamper detect function, the
ST25TV-eSEAL can be used in conjunction with
the DEMO-CR95HF-A demonstration board, or
with an Android™ smart-phone.
www.st.com
Block diagram ST25TV-eSEAL
2/6 DB3596 Rev 1
1 Block diagram
Figure 1. Functional block diagram
069
6779.
&ODVV
DQWHQQDORRS
$&
$&
7'
7'
DB3596 Rev 1 3/6
ST25TV-eSEAL Formal notices required by the U.S. Federal Communications Commission
6
2 Formal notices required by the U.S. Federal
Communications Commission (“FCC”)
2.1 FCC Compliance Statement
2.1.1 Part 15.19
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
2.1.2 Part 15.105
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
2.1.3 Part 15.21
Any changes or modifications to this equipment not expressly approved by
STMicroelectronics may cause harmful interference and void the user’s authority to operate
this equipment.
Formal notices required by the Industry Canada (“IC”) ST25TV-eSEAL
4/6 DB3596 Rev 1
3 Formal notices required by the Industry Canada
(“IC”)
3.1 Compliance Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions : (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation.
3.2 Declaration de Conformité
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
DB3596 Rev 1 5/6
ST25TV-eSEAL Revision history
6
4 Revision history
Table 1. Document revision history
Date Revision Changes
06-June-2018 1 Initial release.
ST25TV-eSEAL
6/6 DB3596 Rev 1
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2018 STMicroelectronics – All rights reserved
