CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LG Radial Lead Type, Higher Capacitance series Higher Capacitance, Low ESR, High ripple current. Load life of 2000 hours at 105C. Radial lead type : Lead free flow soldering condition correspondence Compliant to the RoHS directive (2011/65/EU). LG Higher Capacitance LF Specifications Item Performance Characteristics Category Temperature Range - 55 to +105C Rated Voltage Range 2.5 to 16V Rated Capacitance Range 330 to 3900F Capacitance Tolerance 20% at 120Hz, 20C Tangent of loss angle (tan ) Less than or equal to the specified value at 120Hz, 20C ESR ( Less than or equal to the specified value at 100kHz, 20C 1) Leakage Current ( 2) Less than or equal to the specified value. 1.25 1.25 After 2 minutes' application of rated voltage at 20C Temperature Characteristics (Max.Impedance Ratio) Z+105C / Z+20C Z- 55C / Z+20C (100kHz) Endurance The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours at 105C. Capacitance change tan ESR ( 1) Leakage current ( 2) Within 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 1000 hours at 60C, 90% RH. Capacitance change tan ESR ( 1) Leakage current ( 2) Within 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Resistance to Soldering Heat After soldering the capacitor under the soldering conditions prescribed here as preheat at 150 to 200C for 60 to 180 seconds and peak temperature at 265C for 10 seconds or less, the capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing the soldering side. Capacitance change tan ESR ( 1) Leakage current ( 2) Within 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions Type numbering system (Example : 4V 1200F) Resin coated Case Capacitance 1 2 3 4 5 6 7 8 9 10 11 12 P L G 0 G 1 2 2 MCO 1 P 0.5 D0.5 LG 1200 g 841 Voltage(g:4V) Size code Configuration Capacitance tolerance (20%) d Series Lot. No. L+0.5MAX. 15MIN Rated capacitance (1200F) 4MIN Rated voltage (4V) Size D L P d 8 x 9L 8.0 8.5 3.5 0.6 (mm) 8 x 12L 10 x 13L 8.0 10.0 11.5 3.5 0.6 Series name Type Voltage 12.5 5.0 V 2.5 4 6.3 10 16 0.6 Code e g j A C Please refer to page 20 about the end seal configuration. Dimension table in next page. CAT.8100D CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LG series Standard Ratings Rated Voltage (V) Code 2.5 (0E) 4 (0G) 6.3 (0J) 10 (1A) 16 (1C) Surge Voltage (V) 2.8 4.6 7.2 11.5 18.4 Rated Capacitance (F) Case Size D x L (mm) tan Leakage Current (A) ESR (m) (at 100kHz 20C) Rated Ripple (mArms) Part Number 1800 8x9 2200 8 x 12 0.08 900 9 6000 PLG0E182MCO1 0.08 1100 8 6700 2700 PLG0E222MDO1 10 x 13 0.08 1350 8 5560 PLG0E272MDO1 3900 10 x 13 0.08 1950 8 7000 PLG0E392MDO1 1200 8x9 0.08 960 9 5900 PLG0G122MCO1 1800 8 x 12 0.08 1440 9 6500 PLG0G182MDO1 2700 10 x 13 0.08 2160 8 6900 PLG0G272MDO1 820 8x9 0.08 1033 9 5700 PLG0J821MCO1 1200 8 x 12 0.08 1512 9 6100 PLG0J122MDO1 1500 10 x 13 0.08 1890 9 6300 PLG0J152MDO1 1800 10 x 13 0.08 2268 8 6600 PLG0J182MDO1 560 8x9 0.08 1120 11 5100 PLG1A561MCO1 PLG1A821MDO1 820 8 x 12 0.08 1640 10 5800 1200 10 x 13 0.08 2400 9 6200 PLG1A122MDO1 330 8x9 0.08 1056 13 4700 PLG1C331MCO1 470 8 x 12 0.08 1504 11 5400 PLG1C471MDO1 820 10 x 13 0.08 2624 11 5600 PLG1C821MDO1 Rated ripple current (mArms) at 105C 100kHz Please refer to page 20, 21, 22 about the formed or taped product spec. Please refer to page 3 for the minimum order quantity. CAT.8100D Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Nichicon: PLG0G272MDO1TD PLG1A821MDO1TD PLG1C471MDO1TD