INCH-POUND MIL-DTL-83723/77D 19 August 2009 SUPERSEDING MIL-DTL-83723/77C 20 October 2000 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), PLUG, (RFI, BAYONET COUPLING, CRIMP SOCKET CONTACT), (SERIES III, CLASSES G, M, R, T, W AND Z) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 MIL-DTL-83723/77D FIGURE 1. Dimensions and configurations - Continued. 2 MIL-DTL-83723/77D Shell size 8 A max G min H .312 .352 10 .388 .428 .415 .424 .517 .526 12 .558 .598 14 .627 .667 16 .772 .794 18 .860 .900 20 .985 1.025 22 1.110 1.150 24 1.235 1.275 J L min U max V .540 .545 .662 .667 .632 .776 .025 .760 .906 .031 .687 .696 .756 .765 .883 .892 .989 .998 .832 .837 .901 .906 1.028 1.033 1.134 1.139 .930 1.078 .031 .999 1.141 .031 1.126 1.266 .031 1.232 1.375 .031 1.114 1.123 1.239 1.248 1.261 1.266 1.384 1.389 1.357 1.510 .031 1.482 1.625 .031 1.364 1.373 1.511 1.516 1.607 1.760 .031 FIGURE 1. Dimensions and configurations - Continued. 3 MIL-DTL-83723/77D Inches mm Inches mm Inches mm Inches mm Inches mm .015 .035 .051 .054 .076 .092 .093 .096 .105 .107 .114 .118 .125 .146 .150 .170 .177 .182 .185 .200 0.38 0.89 1.30 1.37 1.93 2.34 2.36 2.44 2.67 2.72 2.90 3.00 3.18 3.71 3.81 4.32 4.50 4.62 4.70 5.08 .206 .210 .312 .320 .352 .366 .383 .388 .415 .424 .428 .517 .526 .540 .545 .552 .558 .598 .627 .632 5.23 5.33 7.92 8.13 8.94 9.30 9.73 9.86 10.54 10.77 10.87 13.13 13.36 13.72 13.84 14.02 14.17 15.19 15.93 16.05 .662 .667 .678 .687 .696 .756 .760 .765 .772 .776 .794 .832 .837 .860 .883 .892 .900 .901 .906 .930 16.81 16.94 17.22 17.45 17.68 19.20 19.30 19.43 19.61 19.71 20.17 21.13 21.36 21.84 22.43 22.66 22.86 22.89 23.01 23.62 .985 .998 .999 1.025 1.028 1.033 1.078 1.110 1.114 1.123 1.126 1.134 1.139 1.141 1.150 1.230 1.232 1.235 1.239 1.248 25.02 25.35 25.37 26.04 26.11 26.24 27.38 28.19 28.30 28.52 28.60 28.80 28.93 28.98 29.21 31.24 31.29 31.37 31.47 31.70 1.261 1.266 1.275 1.357 1.364 1.373 1.375 1.384 1.389 1.482 1.510 1.511 1.516 1.607 1.625 1.760 32.03 32.16 32.39 34.47 34.65 34.87 34.93 35.15 35.28 37.64 38.35 38.38 38.51 40.82 41.28 44.70 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals and .01 (0.25 mm) for two place decimals and 1o for all angles. 4. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723. 5. See table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations - Continued. 4 MIL-DTL-83723/77D REQUIREMENTS: Dimensions and configuration: See figure 1. For insert arrangements, see MIL-STD-1554 and table I. TABLE I. Inserts requiring reduced diameters for lead-in chamfers on contact cavities. Shell size Insert arrangements Contact cavities 8 03 1, 2, 3 10 06 1, 2, 3, 4, 5, 6 For connector accessories: See SAE-AS85049. This connector mates with MIL-DTL-83723/72, MIL-DTL-83723/74, MIL-DTL-83723/79, MIL-DTL-83723/80, MIL-DTL-83723/81, MIL-DTL-83723/93 and MIL-DTL-83723/94. Part or Identifying Number (PIN) example: M83723/ 77 W 22 55 N Military designator Specification sheet number Class Shell size Insert arrangement Polarizing position Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, this document references the following: MIL-DTL-83723/72 MIL-DTL-83723/74 MIL-DTL-83723/79 MIL-DTL-83723/80 MIL-DTL-83723/81 MIL-DTL-83723/93 MIL-DTL-83723/94 MIL-STD-1554 SAE-AS85049 5 MIL-DTL-83723/77D CONCLUDING MATERIAL Custodians: Army - CR Navy - AS Air Force - 85 DLA - CC Preparing activity: DLA - CC (Project 5935-2008-159) Review activities: Army - AR, MI Navy - EC Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil. 6