DETAIL SPECIFIC ATION SHEET
CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING),
PLUG, (RFI, BAYONET COUPLING, CRIMP SOCKET CONTACT),
(SERIES III, CLASSES G, M, R, T, W AND Z)
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
The requirements for acquiring the product described herein
shall consist of this specification sheet and MIL-DTL-83723.
FIGURE 1. Dimensions and configurations.
AMSC N/A FSC 5935
INCH-POUND
MIL-DTL-83723/77D
19 August 2009
SUPERSEDING
MIL-DTL-83723/77C
20 October 2000
MIL-DTL-83723/77D
2
FIGURE 1. Dimensions and configurations - Continued.
MIL-DTL-83723/77D
3
Shell
size
A
max G
min H J L
min U
max V
8
.312
.352 .415
.424
.540
.545
.632 .776 .025
10
.388 .428 .517
.526
.662
.667
.760 .906 .031
12
.558 .598 .687
.696
.832
.837
.930 1.078 .031
14
.627 .667 .756
.765
.901
.906
.999 1.141 .031
16
.772 .794 .883
.892
1.028
1.033
1.126 1.266 .031
18
.860 .900 .989
.998
1.134
1.139
1.232 1.375 .031
20
.985 1.025 1.114
1.123
1.261
1.266
1.357 1.510 .031
22
1.110 1.150 1.239
1.248
1.384
1.389
1.482 1.625 .031
24
1.235 1.275 1.364
1.373
1.511
1.516
1.607 1.760 .031
FIGURE 1. Dimensions and configurations - Continued.
MIL-DTL-83723/77D
4
Inches mm Inches mm Inches mm Inches mm Inches mm
.015 0.38 .206 5.23 .662 16.81 .985 25.02 1.261 32.03
.035 0.89 .210 5.33 .667 16.94 .998 25.35 1.266 32.16
.051 1.30 .312 7.92 .678 17.22 .999 25.37 1.275 32.39
.054 1.37 .320 8.13 .687 17.45 1.025 26.04 1.357 34.47
.076 1.93 .352 8.94 .696 17.68 1.028 26.11 1.364 34.65
.092 2.34 .366 9.30 .756 19.20 1.033 26.24 1.373 34.87
.093 2.36 .383 9.73 .760 19.30 1.078 27.38 1.375 34.93
.096 2.44 .388 9.86 .765 19.43 1.110 28.19 1.384 35.15
.105 2.67 .415 10.54 .772 19.61 1.114 28.30 1.389 35.28
.107 2.72 .424 10.77 .776 19.71 1.123 28.52 1.482 37.64
.114 2.90 .428 10.87 .794 20.17 1.126 28.60 1.510 38.35
.118 3.00 .517 13.13 .832 21.13 1.134 28.80 1.511 38.38
.125 3.18 .526 13.36 .837 21.36 1.139 28.93 1.516 38.51
.146 3.71 .540 13.72 .860 21.84 1.141 28.98 1.607 40.82
.150 3.81 .545 13.84 .883 22.43 1.150 29.21 1.625 41.28
.170 4.32 .552 14.02 .892 22.66 1.230 31.24 1.760 44.70
.177 4.50 .558 14.17 .900 22.86 1.232 31.29
.182 4.62 .598 15.19 .901 22.89 1.235 31.37
.185 4.70 .627 15.93 .906 23.01 1.239 31.47
.200 5.08 .632 16.05 .930 23.62 1.248 31.70
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified, tolerances are ± .005 (0.13 mm) for three place decimals and
± .01 (0.25 mm) for two place decimals and ± 1o for all angles.
4. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723.
5. See table I for contact cavities requiring this dimension.
FIGURE 1. Dimensions and configurations - Continued.
MIL-DTL-83723/77D
5
REQUIREMENTS:
Dimensions and configuration: See figure 1.
For insert arrangements, see MIL-STD-1554 and table I.
TABLE I. Inserts requiring reduced diameters for lead-in chamfers on contact cavities.
Shell size Insert arrangements Contact cavities
8 03 1, 2, 3
10 06 1, 2, 3, 4, 5, 6
For connector accessories: See SAE-AS85049.
This connector mates with MIL-DTL-83723/72, MIL-DTL-83723/74, MIL-DTL-83723/79,
MIL-DTL-83723/80, MIL-DTL-83723/81, MIL-DTL-83723/93 and MIL-DTL-83723/94.
Part or Identifying Number (PIN) example:
M83723/ 77 W 22 55 N
Military designator
Specification sheet number
Class
Shell size
Insert arrangement
Polarizing position
Changes from previous issue. Marginal notations are not used in this revision to identify changes with
respect to the previous issue due to the extent of the changes.
Referenced documents. In addition to MIL-DTL-83723, this document references the following:
MIL-DTL-83723/72
MIL-DTL-83723/74
MIL-DTL-83723/79
MIL-DTL-83723/80
MIL-DTL-83723/81
MIL-DTL-83723/93
MIL-DTL-83723/94
MIL-STD-1554
SAE-AS85049
MIL-DTL-83723/77D
6
CONCLUDING MATERIAL
Custodians: Preparing activity:
Army - CR DLA - CC
Navy - AS
Air Force - 85 (Project 5935-2008-159)
DLA - CC
Review activities:
Army - AR, MI
Navy - EC
Air Force - 19, 99
NOTE: The activities listed above were interested in this document as of the date of this document. Since
organizations and responsibilities can change, you should verify the currency of the information above
using the ASSIST Online database at http://assist.daps.dla.mil.
