TA8470AF/AFG TOSHIBA BIPOLAR LINEAR INTEGRATED CIRCUIT SILICON MONOLITHIC TA8470AF/AFG 3 PHASE FULL WAVE BRUSHLESS DC MOTOR DRIVER IC TA8470AF/AFG is a low-noise type 3 Phase Bi-direction Motor Driver IC, developed as a 3 Phase Hall motor driver for VTRs (capstan, cylinder), etc. FEATURES z Operating Voltage Range : VCC = 7~17 V z Output Current : IO (MAX.) = 1.2 A z Three Phase Bi-direction, current control mode z Low Noise (Quasi Sinusoidal Drive) z Built-in FG Amplifier z Low Output Impedance with B Class Push-Pull Driver, Capable of Short Brakes (Dumping Brakes) Weight : 0.79 g (Typ.) z Position Detecting Circuit (Hall Input) with High Sensitivity : VH = 50 mVp-p z Enclosed in Space-saving Power Flat Package z Built-in Thermal Shutdown Circuit TA8470AFG: The TA8470AFG is a Pb-free product. The following conditions apply to solderability: *Solderability 1. Use of Sn-37Pb solder bath *solder bath temperature = 230C *dipping time = 5 seconds *number of times = once *use of R-type flux 2. Use of Sn-3.0Ag-0.5Cu solder bath *solder bath temperature = 245C *dipping time = 5 seconds *the number of times = once *use of R-type flux 1 2006-3-2 TA8470AF/AFG BLOCK DIAGRAM FUNCTION (VIN- = 5 V) MODE FRS VIN L + VIN > 2.3 V OUTPUT La = Ha - Hb CW Lb = Hb - Hc Lc = Hc - Ha La = -(Ha - Hb) CCW H + VIN > 2.3 V Lb = -(Hb - Hc) Lc = -(Hc - Ha) Standby Brake Note: M Mid-point potentia (Note) + VIN < 2.3 V Mid-point potentia (Note) Low-impedance Mode 2 2006-3-2 TA8470AF/AFG 3 2006-3-2 TA8470AF/AFG 1. Control input circuit In the case of output current feedback to the motor, connect feedback resistance to RF pin (10) and feed it back to NF pin (8). The feedback amount can be adjusted by connecting a resistor between pin (10) and (8) pin. 4 2006-3-2 TA8470AF/AFG 2. FG amplifier and schmitt circuit The FG amplifier is stored with internal reference voltage (2.5 V), making it possible to directly input the FG signal from pattern FG. The Schmitt circuit stored within can output wave-shaped FG signals. FGO is in push-pull mode with low impedance. 5 2006-3-2 TA8470AF/AFG 3. FRS section Voltage applied to FRS pin (15) makes it possible to select forward, reverse, and stop modes. For the relationships between FRS, control input, and output, refer to the item on these functions. The relationship between input voltage (VFRS) and input current (IFRS) to the DRS pin (15) is shown as a feature in the following graph : 6 2006-3-2 TA8470AF/AFG ABSOLUTE MAXIMUM RATINGS (Ta = 25C) CHARACTERISTIC SYMBOL RATING UNIT Supply Voltage VCC 18 V Output Current IO 1.2 A IFGO 12 IFGS 14 FG Output Current mA 1.0 (Note 1) Power Dissipation PD 3.2 (Note 2) W 5.8 (Note 3) Operating Temperature Topr -30~75 C Storage Temperature Tstg -55~150 C Note 1: Without heat sink Note 2: 50 x 50 x 1 mm Fe board mounting Note 3: Infinite heat sink mounting 7 2006-3-2 TA8470AF/AFG ELECTRICAL CHARACTERISTICS (VCC = 12 V, VIN- = 5 V, Ta = 25C) CHARACTERISTIC 12.5 28 1 Output Open, FRS = GND 14 28 ICC 3 1 Output Open, FRS = 5 V 14 28 Input Voltage Range VCIN 2 GND VCC -2.5 V Control Output Voltage Gain GVCO 2 VH = 25 mVp-p 7.5 13 18 dB ICIN 2 VIN = GND (Sink Current) TEST CONDITION UNIT 0.2 5 A Vref 1 2.15 2.30 2.45 V VCMRH 3 1.5 5 V IH 3 0.2 3 A mA + Input Current Common Mode Inoput Voltage Range Input Current VINH = 2.5 V + GVHO 4 VIN = 5 V 40 47 51 dB Upper Side Vsat (U) 5 IO = 1.0 A 1.2 1.9 V Lower Side Vsat (L) 5 IO = 1.0 A 0.7 1.5 + Quiescent Voltage VOS 5 VIN = 1.0 V 5.0 5.5 7.0 V Quiescent Voltage Difference VOOF 5 Each Output to Output 25 50 mV Open Loop Voltage Gain GVFG fFG = 1 kHz 70 dB fFG 6 DC 50 kHz FGO Output Amplitude VFGO 6 IFGO = 5 mA 1.0 2.1 4 V FGS Output Saturation Voltage Vsat (FGS) 6 IFGS = 4 mA 0.15 0.25 V Internal Reference Voltage 2 Vref 2 6 2.1 2.5 2.9 V Schmitt Circuit Hysteresis Width VHYS 6 100 250 mV FWD Operating Voltage VFWD 5 4.0 VCC V Stop Operating Voltage VSTOP 5 1.9 3.1 V Reverse Operating Voltage VREV 5 0 1.3 V TSD 150 C Band Width Rotation Direction Control Circuit ICC 2 Output Open, FRS = 2.5 V Saturation Voltage FG Amp 1 MAX Input Voltage Gain Output Circuit ICC 1 TYP. Internal Reference Voltage 1 Position Detecting Circuit TEST CIR- CUIT MIN Supply Current Speed Control Circuit SYMBOL Thermal Shutdown Operating Temperature 8 2006-3-2 TA8470AF/AFG CHARACTERISTICS OF OUTPUT AMP SATURATION VOLTAGE 9 2006-3-2 TA8470AF/AFG TEST CIRCUIT 1 TEST CIRCUIT 2 TEST CIRCUIT 3 10 2006-3-2 TA8470AF/AFG TEST CIRCUIT 4 TEST CIRCUIT 5 TEST CIRCUIT 6 11 2006-3-2 TA8470AF/AFG APPLICATION CIRCUIT Note 1: All output currents flow into RF pins ; therefore, be sure to provide GND separately from other GND lines. Care should be taken not to have common impedance among other GND lines, either, in making pattern designs (especially for Hall Sensor GND line). Note 2: Utmost care is necessary in the design of the output, VCC, VM, and GND lines since the IC may be destroyed by short-circuiting between outputs, air contamination faults, or faults due to improper grounding, or by short-circuiting between contiguous pins. 12 2006-3-2 TA8470AF/AFG PACKAGE DIMENSIONS HSOP20-P-450-1.00 Unit : mm Weight : 0.79 g (Typ.) 13 2006-3-2 TA8470AF/AFG Notes on Contents 1. Block Diagrams Some of the functional blocks, circuits, or constants in the block diagram may be omitted or simplified for explanatory purposes. 2. Equivalent Circuits The equivalent circuit diagrams may be simplified or some parts of them may be omitted for explanatory purposes. 3. Timing Charts Timing charts may be simplified for explanatory purposes. 4. Application Circuits The application circuits shown in this document are provided for reference purposes only. Thorough evaluation is required, especially at the mass production design stage. Toshiba does not grant any license to any industrial property rights by providing these examples of application circuits. 5. Test Circuits Components in the test circuits are used only to obtain and confirm the device characteristics. These components and circuits are not guaranteed to prevent malfunction or failure from occurring in the application equipment. IC Usage Considerations Notes on handling of ICs [1] The absolute maximum ratings of a semiconductor device are a set of ratings that must not be exceeded, even for a moment. Do not exceed any of these ratings. Exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. [2] Use an appropriate power supply fuse to ensure that a large current does not continuously flow in case of over current and/or IC failure. The IC will fully break down when used under conditions that exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or load, causing a large current to continuously flow and the breakdown can lead smoke or ignition. To minimize the effects of the flow of a large current in case of breakdown, appropriate settings, such as fuse capacity, fusing time and insertion circuit location, are required. [3] If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the design to prevent device malfunction or breakdown caused by the current resulting from the inrush current at power ON or the negative current resulting from the back electromotive force at power OFF. IC breakdown may cause injury, smoke or ignition. Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable, the protection function may not operate, causing IC breakdown. IC breakdown may cause injury, smoke or ignition. [4] Do not insert devices in the wrong orientation or incorrectly. Make sure that the positive and negative terminals of power supplies are connected properly. Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. In addition, do not use any device that is applied the current with inserting in the wrong orientation or incorrectly even just one time. 14 2006-3-2 TA8470AF/AFG Points to remember on handling of ICs (1) Thermal Shutdown Circuit Thermal shutdown circuits do not necessarily protect ICs under all circumstances. If the thermal shutdown circuits operate against the over temperature, clear the heat generation status immediately. Depending on the method of use and usage conditions, such as exceeding absolute maximum ratings can cause the thermal shutdown circuit to not operate properly or IC breakdown before operation. (2) Heat Radiation Design In using an IC with large current flow such as power amp, regulator or driver, please design the device so that heat is appropriately radiated, not to exceed the specified junction temperature (TJ) at any time and condition. These ICs generate heat even during normal use. An inadequate IC heat radiation design can lead to decrease in IC life, deterioration of IC characteristics or IC breakdown. In addition, please design the device taking into considerate the effect of IC heat radiation with peripheral components. (3) Back-EMF When a motor rotates in the reverse direction, stops or slows down abruptly, a current flow back to the motor's power supply due to the effect of back-EMF. If the current sink capability of the power supply is small, the device's motor power supply and output pins might be exposed to conditions beyond maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design. 15 2006-3-2 TA8470AF/AFG 16 2006-3-2