SPECIFICATION CONTROL DRAWING Page
2 of 2
Revision
B
SCD
400R1121
TABLE II. CABLE PERFORMANCE DETAILS
PART NUMBER
1/
BEND TESTING
MANDREL DIAMETER
(inch) (mm) (± 3%) WEIGHT
(lb) (kg) (± 3%)
ACCELERATED
AGING COLD
BEND ACCELERATED
AGING COLD
BEND
400R1121-26-* 3.00 (76.2) 3.00 (76.2) .250 (.113) 1.50 (.680)
400R1121-24-* 3.00 (76.2) 3.00 (76.2) .375 (.170) 1.50 (.680)
400R1121-22-* 6.00 (152.) 6.00 (152.) .375 (.170) 3.00 (1.36)
400R1121-20-* 6.00 (152.) 6.00 (152.) .375 (.170) 3.00 (1.36)
400R1121-18-* 6.00 (152.) 6.00 (152.) .500 (.227) 3.00 (1.36)
400R1121-16-* 6.00 (152.) 6.00 (152.) .500 (.227) 3.00 (1.36)
400R1121-14-* 6.00 (152.) 6.00 (152.) 1.00 (.454) 9.00 (4.08)
400R1121-12-* 10.0 (254.) 10.0 (254.) 1.00 (.454) 9.00 (4.08)
400R1121-10-* 10.0 (254.) 10.0 (254.) 1.00 (.454) 9.00 (4.08)
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
TEMPERATURE RATING: 125°C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
ACCELERATED AGING: 300 ± 3°C for 6 hours
BLOCKING: 150 ± 3°C for 6 hours
DIELECTRIC WITHSTAND: 2500 volts (rms), 60 Hz, 1 minute
FLAMMABILITY: Char Length, 5 ft. (1.5 m) (ma ximum)
JACKET COLOR: White preferred
JACKET CONCENTRICITY: 70% (minimum)
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 200% (minimum)
Tensile Strength, 4000 lbf/in2 (27.6 MPa) (minimum)
JACKET FLAWS:
Spark Test, 1.5 kV (rms)
Impulse Dielectric Test, 6.0 kV (peak)
LOW TEMPERATURE-COLD BEND: -65 ± 2°C for 4 hours
SHIELD COVERAGE: 85% (minimum)
SMOKE RELEASE:
Peak Smoke Release Rate, 0.40 m2/s (maximum)
Total Smoke Release, 150 m2 (maximum)
SMOKE TEST: D4, 50 (maximum); Dm, 300 (maximum)
TOXICITY: HCN: 100 ppm (maximum) SO2: 100 ppm (maximum)
CO: 3500 ppm (maximum) HF: 100 ppm (maximum)
NO: 100 ppm (maximum) HCI: 500 ppm (maximum)
VOLTAGE WITHSTAND (Post Environmental): 1000 volts (rms), 60 Hz, 1 minute
1/ PART NUMBER:
The "*" in the part numbers in Tables I and II shall be replaced by color code
designators with a slash separating the component wire colors and a dash
separating the component wire colors from the jacket color.
Example: AWG 20, black and brown component wires; white jacket:
400R1121-20-0/1-9
CABLE IDENTIFICATION:
Jacket shall be marked in contrasting color as follows:
"RAYCHEM 400R1121-xx - 600V Yr of Mfg" (xx = applicable AWG size)
1/ See footer section on page 1