B-30 APEM www.apem.com
IP series
Momentary pushbutton switches for harsh environments
Distinctive features and specifications
B
❑ Illuminated and non-illuminated
❑ Tactile feedback
❑ Wide variety of configurations
❑ Sealed to IP 67
ENVIRONMENTAL SPECIFICATIONS
• Degree of protection : IP 67
• Shock resistance : 100 g according to IEC 512-4, test 6c
• Vibration resistance : 10-500Hz - 10 g according to IEC 512-4, test 6d
• Salt spray : IEC 512-6, test 11f
• Robustness (non-illuminated sw.) : IK06 according to EN 50102 (1 joule)
• Operating temperature : -40°C to +125°C
ELECTRICAL SPECIFICATIONS
• Max. current/voltage rating with resistive load :
500mA 48VAC - 200mA 50VDC - 200mA 250VAC
• Initial contact resistance : 50 mΩmax.
• Insulation resistance : 1 GΩmin. at 500VDC
• Dielectric strength : 1.500 VAC rms
• Electrical life at full load : 500.000 cycles
• Contact bounce : 10 ms
MATERIALS
• Case : thermoplastic UL94-V0
• Plunger :
polyamide
6/6
• Bushing/bezel : zinc die-cast
(zamac), black painted
• Contacts : silver, gold plated
• Multi-wire lead AWG20,
section 0,6 mm2, UL approved
• LED wire : AWG26
• Lens : polycarbonate
• Terminal seal : epoxy
GENERAL SPECIFICATIONS
• Panel thickness : 1,5 mm (.059) min.
4 mm (.157 max.)
• Total travel : 1,5 mm (.059)
• Operating force : 2N to 5N
• Mechanical life : 1.000.000 cycles
• Torque : 1,5 Nm max. applied to nut
• Soldering : 320°C max. for 3 sec.
LED COMPONENT SPECIFICATIONS
LED colour
Forward current
Super red (L0S) 20mA
20mA
10mA
10mA
20mA
Forward Voltage
2V
2V
2V
3,5V
3,5V
Max. lumin. intensity
125 mcd
125 mcd
20 mcd
20 mcd
280 mcd
Yellow (L0Y)
Green (L0G)
Blue (L0B)
White (L0W)
A resistor must be series-connected by the user.
Resistor value = supply voltage - LED forward voltage
LED forward current
APEM www.apem.com B-31
IP series
Momentary pushbutton switches for harsh environments
Overview
B
IP
SERIES
Bezel shape
CSquare
RRound
Terminals
SSolder lugs
FWire leads
PStraight PC *
Z1 Quick-connect *
* Non-illum. only
Electrical function
3Normally open
(NO)
5NC/NO combined
(non-illuminated)
Plunger colour
1Blue
1/4 Dark blue
2Black
3Green
5Yellow
6Red
7/1 White
8Chrome pl.
9Orange
Contacts
AD Silver, gold
plated
LED colour
Blank Non-illum.
L0S Super red
L0Y Yellow
L0G Green
L0B Blue
L0W White
ABOUT THIS SERIES
On the following pages, you will find successively :
model structure of switches and options in the same order as in above chart
Dimensions : first dimensions are in mm while inches are shown as bracketted numbers.
A sealing boot is available to protect the switches against frost and sand. It is presented at the end of the series and in section H.
Mounting accessories : Standard hardware supplied : 1 hex nut 14 mm (.551) across flats and 1 O-ring.
The hex nut is presented in section I (part number U166).
Packaging unit : 25 pieces
NOTICE : please note that not all combinations of above numbers are available.
Refer to the following pages for further information.
Option
104 High Plunger
For non-illuminated
round models only.
B-32 APEM www.apem.com
IP series
Momentary pushbutton switches for harsh environments
Square - illuminated
B
MODEL
STRUCTURE
• High brightness illumination
• Five LED colours
• Tin plated LED terminals
Solder lug terminals
Ø12.00x0.75SI
(.047)
1.50
5.20
(.015)
(.204)
(.059)
2.00
(.078) 5.08
(.200)
(.267)
1.20
(.251)
6.40 6.80
0.40
EPOXY
(.472DIAx0.75IS)
5.00
(.196)
1.50 Min
(.059 Min)
12.00
(.472SQ)
17.50
(.688SQ)
2.00
(.078)
6.10
(.240)
➞Flat
IPC3SAD Normally Open
Sealed wire lead terminals
Ø12.00x0.75SI
500±10
(19.68±.393)
(.688SQ)
1.50 Min
(.059 Min)
13.20
(.519) 6.80
(.267)
(.472DIAx0.75IS)
5.00
(.196)
12.00
(.472SQ)
(.078)
2.00
17.50
➞Flat
IPC3FAD Normally Open
+-
PLUNGER COLOUR
1: blue - 1/4 : dark blue - 2: black - 3: green - 5: yellow - 6: red - 7/1 : white - 8: chrome plated - 9: orange
LED COLOUR
L0S : super red - L0Y : yellow - L0G : green - L0B : blue - LOW : white
Wire colours : black : NO contact, red : LED anode(+), blue : LED cathode(-)
Cathode
(-)
LED
APEM www.apem.com B-33
IP series
Momentary pushbutton switches for harsh environments
Square - non-illuminated
B
MODEL
STRUCTURE
• Double function (NC/NO combined)
with a short behind-panel depth
Solder lug terminals
Ø12.00x0.75SI
(.047)
1.50
5.20
(.204)
(.059)
2.00
(.078) 5.08
(.200)
(.015)
(.472DIAx0.75IS)
6.40
(.251)
1.20
6.80
(.267)
0.40
EPOXY
5.00
1.50 Min
(.196)
12.00
(.472SQ)
(.059 Min)
(.078)
17.50
(.688SQ)
2.00
NO NO
NC
NC/NONO
➞Flat
IPC3SAD Normally Open
IPC5SAD NC/NO combined
Sealed wire lead terminals
Ø12.00x0.75SI
500±10
(19.68±.393) 1.50 Min
(.059 Min)
(.472DIAx0.75IS)
(.267)
13.20
(.519) 6.80 5.00
(.196)
12.00
(.472SQ)
(.078)
2.00
17.50
(.688SQ)
NO NC/NO
➞Flat
IPC3FAD Normally Open
IPC5FAD NC/NO combined
PLUNGER COLOUR
1: blue - 1/4 : dark blue -2: black - 3: green - 5: yellow - 6: red - 7/1 : white - 8: chrome plated - 9: orange
Wire colours (NC/NO) : black : NO, blue : NC
Function 3 (N0) Function 5 (NC/NO)
5.20
(.204)
1.00
(.039)
4.55
(.179)
1.20
2.80 (.047)
(.110)
8.70
2.40
(.342)
(.094)
Straight PQuick-connect Z1
Also available with straight PC terminals : IPC3PAD (NO) or IPC5PAD (NC/NO)
and quick-connect terminals : IPC3Z1AD (NO only)
B-34 APEM www.apem.com
IP series
Momentary pushbutton switches for harsh environments
Round - illuminated
B
MODEL
STRUCTURE
• High brightness illumination
• Five LED colours
• Tin plated LED terminals
Solder lug terminals
Ø12.00x0.75SI
Ø17.50
(.688DIA)
Ø12.00
(.472DIA)
(.047)
1.50
(.059)
(.204)
(.015)
5.20
(.200)
(.078)
2.00 5.08
EPOXY
0.40
(.472DIAx0.75IS)
(.267)(.251)
1.20
6.806.40
1.50 Min
5.00
(.059 Min)
(.196)
(.078)
2.00
6.10
(.240)
➞Flat
IPR3SAD Normally Open
Sealed wire lead terminals
Ø12.00x0.75SI
(19.68±.393)
500±10
Ø12.00
(.472DIA)
(.688DIA)
Ø17.50
(.196)
5.00
(.059 Min)
1.50 Min
2.00
(.078)
(.472DIAx0.75IS)
13.20
(.519) (.267)
6.80
➞Flat
IPR3FAD Normally Open
+-
PLUNGER COLOUR
1: blue - 1/4 : dark blue - 2: black - 3: green - 5: yellow - 6: red - 7/1 : white - 8: chrome plated - 9: orange
LED COLOUR
L0S : super red - L0Y : yellow - L0G : green - L0B : blue - L0W : white
Wire colours : black : NO contact, red : LED anode(+), blue : LED cathode(-)
Cathode
(-)
LED
APEM www.apem.com B-35
IP series
Momentary pushbutton switches for harsh environments
Round - non-illuminated
B
Function 3 (NO) Function 5 (NC/NO)
MODEL
STRUCTURE
• Double function (NC/NO combined)
with a short behind-panel depth
Solder lug terminals
Ø12.00x0.75SI
Ø17.50
(.688DIA)
Ø12.00
(.472DIA)
(.047)
1.50
(.059)
(.204)
(.015)
5.20
(.078)
2.00 (.200)
5.08
(.251)
6.40
1.20
6.80
(.267)
EPOXY
0.40
(.472DIAx0.75IS)
5.00
(.196)
1.50 Min
(.059 Min)
(.078)
2.00
NO NC/NO
NC
NO NO
➞Flat
IPR3SAD Normally Open
IPR5SAD NC/NO combined
Sealed wire lead terminals
Ø12.00x0.75SI
(19.68±.393)
500±10
Ø12.00
(.472DIA)
(.688DIA)
Ø17.50
(.196)
5.00
(.059 Min)
1.50 Min
2.00
(.078)
13.20
(.519) (.267)
6.80
(.472DIAx0.75IS)
NO NC/NO
➞Flat
IPR3FAD Normally Open
IPR5FAD NC/NO combined
PLUNGER COLOUR
1: blue - 1/4 : dark blue -2: black - 3: green - 5: yellow - 6: red - 7/1 : white - 8: chrome plated - 9: orange
Wire colours (NC/NO) : black : NO, blue : NC
Ø12.00
(.472DIA)
(.185)
4.70
104 : High plunger
PLUNGER OPTION
5.20
(.204)
1.00
(.039)
4.55
(.179)
1.20
2.80 (.047)
(.110)
8.70
2.40
(.342)
(.094)
Straight PQuick-connect Z1
Also available with straight PC terminals : IPR3PAD (NO) or IPR5PAD (NC/NO)
and quick-connect terminals : IPR3Z1AD (NO only)
B-36 APEM www.apem.com
IP series
Momentary pushbutton switches for harsh environments
B
SEALING
IP 67 for the whole series
Degree of protection provided by the enclosures of electric appliances according to IEC 529, DIN 40050 and NFC 20-010.
IP 6 7
(ingress protection) Totally protected Protected against the effects of
against dust immersion up to 1 m water (30 mn)
SOLDER LUG
VERSION
WIRE LEAD
VERSION
MOUNTING
Panel cut-out Matrix mounting
Back of panel space requirement
TACTILE FEEDBACK
Cross section
Operating forces/
travels diagram
(indicative nominal curve)
Ø13.60
(.535DIA)
(.531DIA)
Ø13.50
12.90
(.507)
1
1.50min-4Max
(.059 min-.157max)
20.00
(.787)
20.00
(.787)(.787)
20.00
(.688)
17.50
1 m
1 m
➀ Elastomeric membrane ➁ O-ring
➀ O-ring
Switching point
Force (N)
Trave l (mm)
1.51.20.6
3
The above illustrations show non-illuminated models.
APEM www.apem.com B-37
IP series
Momentary pushbutton switches for harsh environments
B
LUMINANCE MEASUREMENT MODE
Test conditions
ADDITIONAL SEALING
For ROUND plungers only, illuminated
or non-illuminated.
By transparent silicone overboot U5125 for
protection against frost and abrasion by sand.
Order separately.
Operating temperature : -40°C to +125°C.
Transparent Lens
Light Source Luminance-meter
LS110
25cm
(.720 DIA)
Ø18.30
(.346)
8.80
Led types
TEST RESULTS *
* in our lab conditions
For blue and white Led, consult factory. Measured in a dark room
Luminance Forward current
L0S (super red)
4000 Cd/m
2
20mA
L0Y (yellow)
L0G (green)
3500 Cd/m
2
400 Cd/m
2
20mA
10mA
U5125