IP series Momentary pushbutton switches for harsh environments Distinctive features and specifications Illuminated and non-illuminated Tactile feedback Wide variety of configurations Sealed to IP 67 B ENVIRONMENTAL SPECIFICATIONS GENERAL SPECIFICATIONS * Degree of protection : IP 67 * Shock resistance : 100 g according to IEC 512-4, test 6c * Vibration resistance : 10-500Hz - 10 g according to IEC 512-4, test 6d * Salt spray : IEC 512-6, test 11f * Robustness (non-illuminated sw.) : IK06 according to EN 50102 (1 joule) * Operating temperature : -40C to +125C * Panel thickness : 1,5 mm (.059) min. 4 mm (.157 max.) * Total travel : 1,5 mm (.059) * Operating force : 2N to 5N * Mechanical life : 1.000.000 cycles * Torque : 1,5 Nm max. applied to nut * Soldering : 320C max. for 3 sec. ELECTRICAL SPECIFICATIONS MATERIALS * Max. current/voltage rating with resistive load : 500mA 48VAC - 200mA 50VDC - 200mA 250VAC * Initial contact resistance : 50 m max. * Insulation resistance : 1 G min. at 500VDC * Dielectric strength : 1.500 VAC rms * Electrical life at full load : 500.000 cycles * Contact bounce : 10 ms LED COMPONENT SPECIFICATIONS LED colour Forward current Forward Voltage Max. lumin. intensity Super red (L0S) 20mA 2V 125 mcd Yellow (L0Y) 20mA 2V 125 mcd Green (L0G) 10mA 2V 20 mcd Blue (L0B) 10mA 3,5V 20 mcd White (L0W) 20mA 3,5V 280 mcd * Case : thermoplastic UL94-V0 * Plunger : polyamide 6/6 * Bushing/bezel : zinc die-cast (zamac), black painted * Contacts : silver, gold plated * Multi-wire lead AWG20, section 0,6 mm2, UL approved * LED wire : AWG26 * Lens : polycarbonate * Terminal seal : epoxy A resistor must be series-connected by the user. Resistor value = supply voltage - LED forward voltage LED forward current B-30 www.apem.com APEM IP series Momentary pushbutton switches for harsh environments Overview IP Electrical function Bezel shape SERIES C R 3 Square Round 5 Terminals Normally open (NO) NC/NO combined (non-illuminated) S F P Z1 Solder lugs Wire leads Straight PC * Quick-connect * Contacts AD Silver, gold plated * Non-illum. only B Plunger colour 1 1/4 2 3 5 6 7/1 8 9 Blue Dark blue Black Green Yellow Red White Chrome pl. Orange LED colour Blank L0S L0Y L0G L0B L0W Non-illum. Super red Yellow Green Blue White Option 104 High Plunger For non-illuminated round models only. ABOUT THIS SERIES On the following pages, you will find successively : model structure of switches and options in the same order as in above chart Dimensions : first dimensions are in mm while inches are shown as bracketted numbers. NOTICE : please note that not all combinations of above numbers are available. Refer to the following pages for further information. A sealing boot is available to protect the switches against frost and sand. It is presented at the end of the series and in section H. Mounting accessories : Standard hardware supplied : 1 hex nut 14 mm (.551) across flats and 1 O-ring. The hex nut is presented in section I (part number U166). Packaging unit : 25 pieces APEM www.apem.com B-31 IP series Momentary pushbutton switches for harsh environments Square - illuminated * High brightness illumination * Five LED colours * Tin plated LED terminals LED Cathode (-) 1.50 Min (.059 Min) O12.00x0.75SI (.472DIAx0.75IS) 6.10 (.240) 1.50 (.059) 17.50 (.688SQ) EPOXY 1.20 (.047) 0.40 (.015) 2.00 (.078) 5.08 (.200) 5.20 (.204) Normally Open IPC3SAD 6.40 6.80 (.251) (.267) 5.00 (.196) 12.00 (.472SQ) 2.00 (.078) Flat Solder lug terminals - 2.00 (.078) 5.00 (.196) O12.00x0.75SI (.472DIAx0.75IS) 50010 (19.68.393) + 17.50 (.688SQ) 6.80 (.267) Normally Open IPC3FAD 12.00 (.472SQ) 1.50 Min (.059 Min) Flat Sealed wire lead terminals 13.20 (.519) B MODEL STRUCTURE Wire colours : black : NO contact, red : LED anode(+), blue : LED cathode(-) PLUNGER COLOUR 1 : blue - 1/4 : dark blue - 2 : black - 3 : green - 5 : yellow - 6 : red - 7/1 : white - 8 : chrome plated - 9 : orange LED COLOUR L0S : super red - L0Y : yellow - L0G : green - L0B : blue - LOW : white B-32 www.apem.com APEM IP series Momentary pushbutton switches for harsh environments Square - non-illuminated * Double function (NC/NO combined) with a short behind-panel depth 8.70 (.342) 2.40 (.094) Quick-connect Z1 4.55 (.179) 5.20 (.204) Straight P 1.00 (.039) Function 3 (N0) 1.20 (.047) 2.80 (.110) Function 5 (NC/NO) MODEL STRUCTURE B Normally Open IPC5SAD NC/NO combined 1.50 Min (.059 Min) O12.00x0.75SI (.472DIAx0.75IS) NO EPOXY 1.50 (.059) 17.50 (.688SQ) 1.20 (.047) 0.40 (.015) 2.00 (.078) NO NC 5.08 (.200) NO 5.20 (.204) IPC3SAD 6.40 6.80 (.251) (.267) 5.00 (.196) 12.00 (.472SQ) 2.00 (.078) Flat Solder lug terminals NC/NO Also available with straight PC terminals : IPC3PAD (NO) or IPC5PAD (NC/NO) and quick-connect terminals : IPC3Z1AD (NO only) 6.80 (.267) IPC5FAD NC/NO combined 2.00 (.078) 17.50 (.688SQ) O12.00x0.75SI (.472DIAx0.75IS) 50010 (19.68.393) Normally Open 13.20 (.519) 5.00 (.196) IPC3FAD 12.00 (.472SQ) 1.50 Min (.059 Min) Flat Sealed wire lead terminals NO NC/NO Wire colours (NC/NO) : black : NO, blue : NC PLUNGER COLOUR 1 : blue - 1/4 : dark blue -2 : black - 3 : green - 5 : yellow - 6 : red - 7/1 : white - 8 : chrome plated - 9 : orange APEM www.apem.com B-33 IP series Momentary pushbutton switches for harsh environments Round - illuminated * High brightness illumination * Five LED colours * Tin plated LED terminals LED Cathode (-) 1.50 Min (.059 Min) O17.50 (.688DIA) 1.50 (.059) 6.10 (.240) O12.00x0.75SI (.472DIAx0.75IS) EPOXY 1.20 (.047) 0.40 (.015) 2.00 (.078) 5.08 (.200) 5.20 (.204) Normally Open IPR3SAD 6.40 6.80 (.251) (.267) 5.00 (.196) O12.00 (.472DIA) 2.00 (.078) Flat Solder lug terminals - 2.00 (.078) 5.00 (.196) O12.00x0.75SI (.472DIAx0.75IS) 50010 (19.68.393) + O17.50 (.688DIA) 6.80 (.267) Normally Open IPR3FAD O12.00 (.472DIA) 1.50 Min (.059 Min) Flat Sealed wire lead terminals 13.20 (.519) B MODEL STRUCTURE Wire colours : black : NO contact, red : LED anode(+), blue : LED cathode(-) PLUNGER COLOUR 1 : blue - 1/4 : dark blue - 2 : black - 3 : green - 5 : yellow - 6 : red - 7/1 : white - 8 : chrome plated - 9 : orange LED COLOUR L0S : super red - L0Y : yellow - L0G : green - L0B : blue - L0W : white B-34 www.apem.com APEM IP series Momentary pushbutton switches for harsh environments Round - non-illuminated * Double function (NC/NO combined) with a short behind-panel depth Function 3 (NO) 8.70 (.342) 2.40 (.094) Quick-connect Z1 4.55 (.179) 5.20 (.204) Straight P 1.00 (.039) Function 5 (NC/NO) 1.20 (.047) 2.80 (.110) MODEL STRUCTURE B Normally Open IPR5SAD NC/NO combined 1.50 Min (.059 Min) O12.00x0.75SI (.472DIAx0.75IS) NO 1.50 (.059) 1.20 (.047) 2.00 (.078) NO NC EPOXY Also available with straight PC terminals : IPR3PAD (NO) or IPR5PAD (NC/NO) and quick-connect terminals : IPR3Z1AD (NO only) O17.50 (.688DIA) 0.40 (.015) 5.08 (.200) NO 5.20 (.204) IPR3SAD 6.40 6.80 (.251) (.267) 5.00 (.196) O12.00 (.472DIA) 2.00 (.078) Flat Solder lug terminals NC/NO 6.80 (.267) IPR5FAD NC/NO combined 1.50 Min (.059 Min) O17.50 (.688DIA) O12.00x0.75SI (.472DIAx0.75IS) 50010 (19.68.393) Normally Open 13.20 (.519) 5.00 (.196) IPR3FAD O12.00 (.472DIA) 2.00 (.078) Flat Sealed wire lead terminals NO NC/NO Wire colours (NC/NO) : black : NO, blue : NC PLUNGER COLOUR PLUNGER OPTION O12.00 (.472DIA) 4.70 (.185) 1 : blue - 1/4 : dark blue -2 : black - 3 : green - 5 : yellow - 6 : red - 7/1 : white - 8 : chrome plated - 9 : orange 104 : High plunger APEM www.apem.com B-35 IP series Momentary pushbutton switches for harsh environments MOUNTING Matrix mounting 1.50min-4Max (.059 min-.157max) Panel cut-out 20.00 (.787) 20.00 (.787) 1 20.00 (.787) 17.50 (.688) 12.90 (.507) Back of panel space requirement O13.60 (.535DIA) O13.50 (.531DIA) O-ring B TACTILE FEEDBACK Cross section Force (N) 1 Operating forces/ travels diagram (indicative nominal curve) 3 2 Switching point 0.6 1.2 1.5 Travel (mm) Elastomeric membrane O-ring SEALING IP 67 for the whole series Degree of protection provided by the enclosures of electric appliances according to IEC 529, DIN 40050 and NFC 20-010. IP 6 7 (ingress protection) Totally protected against dust Protected against the effects of immersion up to 1 m water (30 mn) 1m SOLDER LUG VERSION 1m WIRE LEAD VERSION The above illustrations show non-illuminated models. B-36 www.apem.com APEM IP series Momentary pushbutton switches for harsh environments LUMINANCE MEASUREMENT MODE Test conditions Transparent Lens Light Source TEST RESULTS * Led types Luminance L0S (super red) 4000 Cd/m2 20mA L0Y (yellow) 3500 Cd/m 20mA L0G (green) 400 Cd/m2 Luminance-meter Forward current 2 LS110 10mA B 25cm * in our lab conditions For blue and white Led, consult factory. Measured in a dark room ADDITIONAL SEALING By transparent silicone overboot U5125 for protection against frost and abrasion by sand. Order separately. Operating temperature : -40C to +125C. APEM 8.80 (.346) For ROUND plungers only, illuminated or non-illuminated. O18.30 (.720 DIA) U5125 www.apem.com B-37