50A Integrated PowIRstage(R) FEATURES DESCRIPTION Peak efficiency up to 94.5% at 1.2V Integrated driver, control MOSFET, synchronous MOSFET and Schottky diode Input voltage (VIN) operating range up to 15V Output voltage range from 0.25V to Vcc-2.5V, or to 5.5V if internal current sense amplifier is not used Output current capability of 50A DC Operation up to 1.0MHz The IR3551 integrated PowIRstage(R) is a synchronous buck gate driver co-packed with a control MOSFET and a synchronous MOSFET with integrated Schottky diode. It is optimized internally for PCB layout, heat transfer and driver/MOSFET timing. Custom designed gate driver and MOSFET combination enables higher efficiency at lower output voltages required by cutting edge CPU, GPU and DDR memory designs. Up to 1.0MHz switching frequency enables high performance transient response, allowing miniaturization of output inductors, as well as input and output capacitors while maintaining industry leading efficiency. The IR3551's superior efficiency enables smallest size and lower solution cost. The IR3551 PCB footprint is compatible with the IR3550 (60A) and the IR3553 (40A). Integrated current sense amplifier VCC under voltage lockout Thermal flag Body-Braking(R) load transient support Diode-emulation high efficiency mode Compatible with 3.3V PWM logic and VCC tolerant Compliant with Intel DrMOS V4.0 PCB footprint compatible with IR3550 and IR3553 Efficient dual sided cooling Small 5mm x 6mm x 0.9mm PQFN package Lead free RoHS compliant package APPLICATIONS Integrated current sense amplifier achieves superior current sense accuracy and signal to noise ratio vs. best-inclass controller based Inductor DCR sense methods. The IR3551 incorporates the Body-Braking(R) feature which enables reduction of output capacitors. Synchronous diode emulation mode in the IR3551 removes the zero-current detection burden from the PWM controller and increases system light-load efficiency. High current, low profile DC-DC converters BASIC APPLICATION VIN 4.5V to 7V VIN 4.5V to 15V BOOST PHSFLT# PHSFLT# SW VOUT Efficiency (%) VCC IR3551 95 20 93 18 91 16 89 14 87 12 85 10 83 8 PWM PWM 81 6 BBRK# BBRK# 79 4 REFIN REFIN CSIN+ 77 2 IOUT CSIN- 75 LGND PGND IOUT Power Loss (W) The IR3551 is optimized specifically for CPU core power delivery in server applications. The ability to meet the stringent requirements of the server market also makes the IR3551 ideally suited to powering GPU and DDR memory designs and other high current applications. Voltage Regulators for CPUs, GPUs, and DDR memory arrays VCC IR3551 0 0 5 10 15 20 25 30 35 40 45 50 Output Current (A) Figure 1: IR3551 Basic Application Circuit 1 July 16, 2013 | DATASHEET V3.2 Figure 2: Typical IR3551 Efficiency & Power Loss (See Note 2 on Page 8) 50A Integrated PowIRstage(R) PINOUT DIAGRAM IR3551 ORDERING INFORMATION Package Tape & Reel Qty Part Number PQFN, 28 Lead 5mm x 6mm 3000 IR3551MTRPBF Package Qty Part Number PQFN, 28 Lead 5mm x 6mm 100 IR3551MPBF Figure 3: IR3551 Pin Diagram, Top View TYPICAL APPLICATION DIAGRAM VCC 4.5V to 7V C3 1uF R1 10k PHSFLT# PWM BBRK# Optional for diode emulation setup REFIN C8 1nF IR3551 21 PHSFLT# 22 PWM 23 BBRK# C9 22nF 24 LGND 25 REFIN 26 IOUT 3 16-19 VCC VIN C1 0.22uF BOOST Gate Drivers and Current Sense Amplifier 20 C5 0.22uF 27 1 No Connect R2 2.49k CSIN+ 2 Figure 4: Application Circuit with Current Sense Amplifier 2 July 16, 2013 | DATASHEET V3.2 VIN 4.5V to 15V C6 22uF C7 470uF VOUT 6-13 PGND 14, 15 PGND 4 CSIN- L1 150nH SW IOUT TGND C2 10uF x 2 C4 0.22uF 50A Integrated PowIRstage(R) IR3551 TYPICAL APPLICATION DIAGRAM (CONTINUED) VCC 4.5V to 7V C3 0.22uF R1 10k IR3551 PHSFLT# PWM BBRK# 21 PHSFLT# 22 PWM 23 BBRK# 24 LGND 25 REFIN 26 IOUT 3 16-19 VCC VIN C1 0.22uF BOOST Gate Drivers and Current Sense Amplifier 20 C2 10uF x 2 C5 0.22uF L1 150nH CSIN- C7 470uF VOUT 6-13 R2 2.49k C4 0.22uF CS+ CS- CSIN+ 1 27 No Connect C6 22uF SW PGND 14, 15 PGND 4 TGND VIN 4.5V to 15V 2 Figure 5: Application Circuit without Current Sense Amplifier FUNCTIONAL BLOCK DIAGRAM BOOST VIN VIN VIN VIN 20 16 17 18 19 IR3551 VCC 3 VCC 3.3V 200k BBRK# 23 S Power-on Reset (POR), 3.3V Reference, and Dead-time Control Q R POR 3.3V PWM 22 PHSFLT# 21 LGND 24 IOUT 26 REFIN 25 MOSFET & Thermal Detection Driver Diode Emulation Comparator - + - 27 CSIN- CSIN+ PGND TGND 5 28 GATEL GATEL Figure 6: IR3551 Functional Block Diagram 3 July 16, 2013 | DATASHEET V3.2 SW 9 SW 13 SW 18k Driver 4 8 12 SW VCC 2 SW 11 SW Offset +- 1 SW 7 10 SW + Current Sense Amplifier 6 14 15 PGND PGND 50A Integrated PowIRstage(R) IR3551 PIN DESCRIPTIONS PIN # PIN NAME PIN DESCRIPTION 1 CSIN- Inverting input to the current sense amplifier. Connect to LGND if the current sense amplifier is not used. 2 CSIN+ Non-Inverting input to the current sense amplifier. Connect to LGND if the current sense amplifier is not used. 3 VCC Bias voltage for control logic. Connect a minimum 1uF cap between VCC and PGND (pin 4) if current sense amplifier is used. Connect a minimum 0.22uF capacitor between VCC and PGND (pin 4) if current sense amplifier is not used. 4, 14, 15 PGND Power ground of MOSFET driver and the synchronous MOSFET. MOSFET driver signal is referenced to this pin. 5, 28 GATEL Low-side MOSFET driver pins that can be connected to a test point in order to observe the waveform. 6 - 13 SW Switch node of synchronous buck converter. VIN High current input voltage connection. Recommended operating range is 4.5V to 15V. Connect at least two 10uF 1206 ceramic capacitors and a 0.22uF 0402 ceramic capacitor. Place the capacitors as close as possible to VIN pins and PGND pins (14-15). The 0.22uF 0402 capacitor should be on the same side of the PCB as the IR3551. 20 BOOST Bootstrap capacitor connection. The bootstrap capacitor provides the charge to turn on the control MOSFET. Connect a minimum 0.22F capacitor from BOOST to SW pin. Place the capacitor as close to BOOST pin as possible and minimize parasitic inductance of PCB routing from the capacitor to SW pin. 21 PHSFLT# Open drain output of the phase fault circuits. Connect to an external pull-up resistor. Output is low when a MOSFET fault or over temperature condition is detected. PWM 3.3V logic level tri-state PWM input and 7V tolerant. "High" turns the control MOSFET on, and "Low" turns the synchronous MOSFET on. "Tri-state" turns both MOSFETs off in Body-Braking(R) mode. In diode emulation mode, "Tri-state" activates internal diode emulation control. See "PWM Tri-state Input" Section for further details about the PWM Tri-State functions. 23 BBRK# 3.3V logic level input and 7V tolerant with internal weak pull-up to 3.3V. Logic low disables both MOSFETs. Pull up to VCC directly or by a 4.7k resistor if Body-Braking(R) is not used. The second function of the BBRK# pin is to select diode emulatiom mode. Pulling BBRK# low at least 20ns after VCC passes its UVLO threshold selects internal diode emulation control. See "Body-Braking(R) Mode" Section for further details. 24 LGND Signal ground. Driver control logic, analog circuits and IC substrate are referenced to this pin. 25 REFIN Reference voltage input from the PWM controller. IOUT signal is referenced to the voltage on this pin. Connect to LGND if the current sense amplifier is not used. 26 IOUT Current output signal. Voltage on this pin is equal to V(REFIN) + 32.5 * [V(CSIN+) - V(CSIN-)]. Float this pin if the current sense amplifier is not used. TGND This pin is connected to internal power and signal ground of the driver. For best performance of the current sense amplifier, TGND must be electrically isolated from Power Ground (PGND) and Signal Ground (LGND) in the PCB layout. Connect to PGND if the current sense amplifier is not used. 16 - 19 22 27 4 July 16, 2013 | DATASHEET V3.2 50A Integrated PowIRstage(R) IR3551 ABSOLUTE MAXIMUM RATINGS Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications are not implied. PIN Number PIN NAME VMAX VMIN ISOURCE ISINK 1 CSIN- VCC + 0.3V -0.3V 1mA 1mA 2 CSIN+ VCC + 0.3V -0.3V 1mA 1mA 5A for 100ns, 200mA DC 3 VCC 8V -0.3V NA 4 PGND 0.3V 5, 28 GATEL VCC + 0.3V 6-13 SW -0.3V -3V for 20ns, -0.3V DC -5V for 20ns, -0.3V DC 14, 15 PGND NA NA 15mA 1A for 100ns, 200mA DC 55A RMS, 75A Peak 25A RMS, 30A Peak 16-19 VIN 2 25V -0.3V 5A RMS 20 BOOST 33V -0.3V 1A for 100ns, 100mA DC 15mA 1A for 100ns, 200mA DC 25A RMS, 30A Peak 55A RMS, 75A Peak 20A RMS, 25A Peak 5A for 100ns, 100mA DC 21 PHSFLT# VCC + 0.3V -0.3V 1mA 20mA 22 PWM VCC + 0.3V -0.3V 1mA 1mA 23 BBRK# VCC + 0.3V -0.3V 1mA 1mA 24 LGND 0.3V -0.3V 15mA 15mA 25 REFIN 3.5V -0.3V 1mA 1mA 26 IOUT VCC + 0.3V -0.3V 5mA 5mA 27 TGND 0.3V -0.3V NA NA 2 25V 1 Note: 1. Maximum BOOST - SW = 8V. 2. Maximum VIN - SW = 25V. 3. All the maximum voltage ratings are referenced to PGND (Pins 14 and 15). THERMAL INFORMATION Thermal Resistance, Junction to Top (JC_TOP) 17.5 C/W Thermal Resistance, Junction to PCB (pin 15) (JB) 2.1 C/W Thermal Resistance (JA) 1 21.1 C/W Maximum Operating Junction Temperature -40 to 150C Maximum Storage Temperature Range -65C to 150C ESD rating HBM Class 1B JEDEC Standard MSL Rating 3 Reflow Temperature 260C Note: 1. Thermal Resistance (JA) is measured with the component mounted on a high effective thermal conductivity test board in free air. Refer to International Rectifier Application Note AN-994 for details. 5 July 16, 2013 | DATASHEET V3.2 50A Integrated PowIRstage(R) IR3551 ELECTRICAL SPECIFICATIONS The electrical characteristics involve the spread of values guaranteed within the recommended operating conditions. Typical values represent the median values, which are related to 25C. RECOMMENDED OPERATING CONDITIONS FOR RELIABLE OPERATION WITH MARGIN PARAMETER SYMBOL MIN MAX UNIT Recommended VIN Range VIN 4.5 15 V Recommended VCC Range VCC 4.5 7 V REFIN 0.25 VCC - 2.5 V Recommended Switching Frequency SW 200 1000 kHz Recommended Operating Junction Temperature TJ -40 125 C Recommended REFIN Range ELECTRICAL CHARACTERISTICS PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT Efficiency and Maximum Current IR3551 Peak Efficiency Note 1 IR3551 Maximum DC Current Note 1 Note 2. See Figure 2. 94.0 % Note 3. See Figure 7. 93.4 % IDC_MAX Note 2. 50 A IPK_MAX Note 4. 5ms load pulse width, 10% load duty cycle. 75 A PWM Input High Threshold VPWM_HIGH PWM Tri-state to High PWM Input Low Threshold VPWM_LOW PWM Tri-state to Low PWM Tri-state Float Voltage VPWM_TRI PWM Floating 1.2 Hysteresis VPWM_HYS Active to Tri-state or Tristate to Active, Note 1 65 IR3551 Maximum Peak Current Note 1 PWM Comparator Tri-state Propagation Delay tPWM_DELAY 2.5 V 0.8 V 1.65 2.1 V 76 100 mV PWM Tri-state to Low transition to GATEL >1V 38 ns PWM Tri-state to High transition to GATEH >1V 18 ns PWM Sink Impedance RPWM_SINK 3.67 5.1 8.70 k PWM Source Impedance RPWM_SOURCE 3.67 5.1 8.70 k Internal Pull up Voltage VPWM_PULLUP VCC > UVLO 3.3 Minimum Pulse Width tPWM_MIN Note 1 41 58 ns V Current Sense Amplifier CSIN+/- Bias Current ICSIN_BIAS -100 0 100 nA CSIN+/- Bias Current Mismatch ICSIN_BIASMM -50 0 50 nA Calibrated Input Offset Voltage VCSIN_OFFSET 6 July 16, 2013 | DATASHEET V3.2 Self-calibrated offset, 0.5V V(REFIN) 2.25V 450 V 50A Integrated PowIRstage(R) PARAMETER Gain SYMBOL GCS IR3551 CONDITIONS MIN TYP MAX UNIT 0.5V V(REFIN) 2.25V, -5mV *V(CSIN+) -V(CSIN-)] 25mV, 0C TJ 125C 30.0 32.5 35.0 V/V 0.5V V(REFIN) 2.25V, -5mV *V(CSIN+) - V(CSIN-)] 25mV 30.0 33.0 36.0 V/V 0.8V V(REFIN) 2.25V, -10mV *V(CSIN+)-V(CSIN-)] 25mV 28.0 31.5 35.0 V/V C(IOUT) = 10pF. Measure at IOUT. Note 1 4.8 6.8 8.8 MHz Unity Gain Bandwidth fBW Slew Rate SR Differential Input Range VD_IN Common Mode Input Range VC_IN Output Impedance (IOUT) RCS_OUT IOUT Sink Current ICS_SINK Driving external 3 k Input Offset Voltage VIN_OFFSET Leading Edge Blanking Time Negative Current Time-Out 6 0.8V V(REFIN) 2.25V, V/s -10 25 mV 0 VCC2.5 V 62 200 0.5 0.8 1.1 mA Note 1 -12 -3 3 mV tBLANK V(GATEL)>1V Starts Timer 50 150 200 ns tNC_TOUT PWM = Tri-State, V(SW) -10mV 12 28 46 s Diode Emulation Mode Comparator Digital Input - BBRK# Input voltage high VBBRK#_IH 2.0 Input voltage low VBBRK#_IL Internal Pull Up Resistance RBBRK#_PULLUP VCC > UVLO Internal Pull Up Voltage VBBRK#_PULLUP VCC > UVLO 69 V 200 0.8 V 338 k 3.3 V Digital Output - PHSFLT# Output voltage high VPHASFLT#_OH VCC V Output voltage low VPHASFLT#_OL 4mA 150 300 mV Input current IPHASFLT#_IN V(PHSFLT#) = 5.5V 0 1 A Control MOSFET Short Threshold VCM_SHORT Measure from SW to PGND Synchronous MOSFET Short Threshold VSM_SHORT Measure from SW to PGND 150 200 250 mV Synchronous MOSFET Open Threshold VSM_OPEN Measure from SW to PGND -250 -200 -150 mV Propagation Delay tPROP PWM High to Low Cycles 15 Cycle Rising Threshold TRISE PHSFLT# Drives Low, Note 1 160 C Falling Threshold TFALL Note 1 135 C Phase Fault Detection 3.3 V Thermal Flag 7 July 16, 2013 | DATASHEET V3.2 50A Integrated PowIRstage(R) PARAMETER SYMBOL IR3551 CONDITIONS MIN TYP MAX UNIT I(BOOST) = 30mA, VCC=6.8V 360 520 920 mV Bootstrap Diode Forward Voltage VFWD VCC Under Voltage Lockout Start Threshold VVCC_START 3.3 3.7 4.1 V Stop Threshold VVCC_STOP 3.0 3.4 3.8 V Hysteresis VVCC_HYS 0.2 0.3 0.4 V 4 8 12 mA 1 A General VCC Supply Current IVCC VCC = 4.5V to 7V VIN Supply Leakage Current IVIN VIN = 20V, 125C, V(PWM) = Tri-State BOOST Supply Current IBOOST 4.75V < V(BOOST)-V(SW) < 8V REFIN Bias Current IREFIN SW Floating Voltage VSW_FLOAT SW Pull Down Resistance RSW_PULLDOWN 0.5 1.5 3.0 mA -1.5 0 1 A V(PWM) = Tri-State 0.2 0.4 V BBRK# is Low or VCC = 0V 18 k Notes 1. Guaranteed by design but not tested in production 2. VIN=12V, VOUT=1.2V, SW = 300kHz, L=210nH (0.2m), VCC=6.8V, CIN=47uF x 4, COUT =470uF x3, 400LFM airflow, no heat sink, 25C ambient temperature, and 8-layer PCB of 3.7" (L) x 2.6" (W). PWM controller loss and inductor loss are not included. 3. VIN=12V, VOUT=1.2V, SW = 400kHz, L=150nH (0.29m), VCC=7V, CIN=47uF x 4, COUT =470uF x3, no airflow, no heat sink, 25C ambient temperature, and 8-layer PCB of 3.7" (L) x 2.6" (W). PWM controller loss and inductor loss are not included. 4. VIN=12V, VOUT=1.2V, SW = 400kHz, L=210nH (0.2m, 13mm x 13mm x 8mm), VCC=6.8V, CIN=47uF x 4, COUT =470uF x3, no heat sink, 25C ambient temperature, 8-layer PCB of 3.7" (L) x 2.6" (W), 5ms load pulse width, 10% load duty cycle, and IR3551 junction temperature below 125C. 8 July 16, 2013 | DATASHEET V3.2 50A Integrated PowIRstage(R) IR3551 TYPICAL OPERATING CHARACTERISTICS Circuit of Figure 32, VIN=12V, VOUT=1.2V, SW = 400kHz, L=150nH (0.29m), VCC=7V, TAMBIENT = 25C, no heat sink, no air flow, 8-layer PCB board of 3.7" (L) x 2.6" (W), no PWM controller loss, no inductor loss, unless specified otherwise. 94 1.15 3.3 1.10 2.2 1.05 1.1 1.00 0.0 0.95 -1.1 0.90 -2.2 92 91 Normalized Power Loss Efficiency (%) 90 89 88 87 86 85 84 83 82 Case Temperature Adjustment (C) 93 81 80 10 15 20 25 30 35 40 45 50 0.85 -3.3 5 6 7 8 9 Output Current (A) 11 12 13 14 15 Input Voltage (V) Figure 10: Normalized Power Loss vs. Input Voltage Figure 7: Typical IR3551 Efficiency 10 1.40 8.8 9 1.35 7.7 8 1.30 6.6 1.25 5.5 1.20 4.4 1.15 3.3 1.10 2.2 1.05 1.1 1.00 0.0 2 0.95 -1.1 1 0.90 -2.2 0 0.85 Normalized Power Loss 7 6 5 4 3 0 5 10 15 20 25 30 35 40 45 50 -3.3 0.8 0.9 1 1.1 Output Current (A) 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 Output Voltage (V) Figure 11: Normalized Power Loss vs. Output Voltage Figure 8: Typical IR3551 Power Loss Normalized Power Loss Power Loss (W) 10 Case Temperature Adjustment (C) 5 1.40 8.8 1.35 7.7 1.30 6.6 1.25 5.5 1.20 4.4 1.15 3.3 1.10 2.2 1.05 1.1 1.00 0.0 0.95 -1.1 0.90 -2.2 0.85 Case Temperature Adjustment (C) 0 -3.3 200 300 400 500 600 700 800 900 1000 Switching Frequency (kHz) Figure 9: Thermal Derating Curve, TCASE <= 125C 9 July 16, 2013 | DATASHEET V3.2 Figure 12: Normalized Power Loss vs. Switching Frequency 50A Integrated PowIRstage(R) IR3551 TYPICAL OPERATING CHARACTERISTICS (CONTINUED) 1.20 4.4 1.15 3.3 1.10 2.2 1.05 1.1 1.00 0.0 0.95 -1.1 0.90 -2.2 0.85 -3.3 5.00 5.25 5.50 5.75 6.00 6.25 6.50 6.75 PWM 5V/div Case Temperature Adjustment (C) Normalized Power Loss Circuit of Figure 32, VIN=12V, VOUT=1.2V, SW = 400kHz, L=150nH (0.29m), VCC=7V, TAMBIENT = 25C, no heat sink, no air flow, 8-layer PCB board of 3.7" (L) x 2.6" (W), no PWM controller loss, no inductor loss, unless specified otherwise. GATEL 10V/div 7.00 VCC Voltage (V) 400ns/div Figure 13: Normalized Power Loss vs. VCC Voltage 1.15 3.3 1.10 2.2 1.05 1.1 1.00 0.0 0.95 -1.1 0.90 -2.2 0.85 -3.3 Figure 16: Switching Waveform, IOUT = 0A PWM 5V/div Case Temperature Adjustment (C) Normalized Power Loss SW 5V/div SW 5V/div GATEL 10V/div 120 130 140 150 160 170 180 190 200 210 Output Inductor (nH) 400ns/div Figure 14: Power Loss vs. Output Inductor Figure 17: Switching Waveform, IOUT = 50A 70 PWM 2V/div 60 Vcc=6.8V VCC Current (mA) 50 Vcc=5V 40 30 SW 5V/div 20 10 0 200 300 400 500 600 700 800 900 fsw (kHz) Figure 15: VCC Current vs. Switching Frequency 10 July 16, 2013 | DATASHEET V3.2 1000 40ns/div Figure 18: PWM to SW Delays, IOUT = 10A 50A Integrated PowIRstage(R) IR3551 TYPICAL OPERATING CHARACTERISTICS (CONTINUED) Circuit of Figure 32, VIN=12V, VOUT=1.2V, SW = 400kHz, L=150nH (0.29m), VCC=7V, TAMBIENT = 25C, no heat sink, no air flow, 8-layer PCB board of 3.7" (L) x 2.6" (W), no PWM controller loss, no inductor loss, unless specified otherwise. PWM 2V/div BBRK# 5V/div PWM 5V/div SW 5V/div GATEL 5V/div GATEL 10V/div 40ns/div 400ns/div Figure 19: Body-Braking(R) Delays Figure 22: Diode Emulation Mode, IOUT = 3A PWM 2V/div PWM 2V/div SW 5V/div SW 5V/div GAETL 10V/div 100ns/div 400ns/div Figure 20: PWM Tri-state Delays, IOUT = 10A Figure 23: Body-Braking(R) Mode, IOUT = 3A VCC 2V/div PWM 2V/div BBRK# 1V/div SW 5V/div SW 10V/div 100ns/div Figure 21: PWM Tri-state Delays, IOUT = 10A 11 July 16, 2013 | DATASHEET V3.2 2ms/div Figure 24: Diode Emulation Setup through BBRK# Capacitor 50A Integrated PowIRstage(R) IR3551 TYPICAL OPERATING CHARACTERISTICS (CONTINUED) Circuit of Figure 32, VIN=12V, VOUT=1.2V, SW = 400kHz, L=150nH (0.29m), VCC=7V, TAMBIENT = 25C, no heat sink, no air flow, 8-layer PCB board of 3.7" (L) x 2.6" (W), no PWM controller loss, no inductor loss, unless specified otherwise. V(IOUT)V(REFIN) 0.2V/div VCC 2V/div IL 10A/div BBRK# 2V/div SW 20V/div 2us/div 4ms/div Figure 25: Diode Emulation Setup through BBRK# Input Figure 28: Current Sense Amplifier Output, IOUT = 0A V(IOUT)V(REFIN) 0.2V/div VCC 2V/div IL 10A/div BBRK# 2V/div SW 20V/div 2us/div 4ms/div Figure 26: Diode Emulation Setup through BBRK# Input Figure 29: Current Sense Amplifier Output, IOUT = 20A 0.60 0.55 V(IOUT)V(REFIN) 0.2V/div 0.50 0.45 IOUT-REFIN (V) 0.40 0.35 IL 10A/div 0.30 0.25 0.20 0.15 0.10 0.05 0.00 0 5 10 15 20 25 30 35 40 45 SW 20V/div 50 Output Current (A) 2us/div Figure 27: Current Sense Amplifier Output vs. Current 12 July 16, 2013 | DATASHEET V3.2 Figure 30: Current Sense Amplifier Output, IOUT = 40A 50A Integrated PowIRstage(R) THEORY OF OPERATION DESCRIPTION The IR3551 PowIRstage(R) is a synchronous buck driver with co-packed MOSFETs with integrated Schottky diode, which provides system designers with ease of use and flexibility required in cutting edge CPU, GPU and DDR memory power delivery designs and other high-current low-profile applications. The IR3551 is designed to work with a PWM controller. It incorporates a continuously self-calibrated current sense amplifier, optimized for use with inductor DCR sensing. The current sense amplifier provides signal gain and noise immunity, supplying multiphase systems with a superior design toolbox for programmed impedance designs. The IR3551 provides a phase fault signal capable of detecting open or shorted MOSFETs, or an overtemperature condition in the vicinity of the power stage. IR3551 a synchronous diode emulation feature allowing designers to maximize system efficiency at light loads without compromising transient performance. Once the diode emulation mode is set, it cannot be reset until the VCC power is recycled. PWM TRI-STATE INPUT The IR3551 PWM accepts 3-level input signals. When PWM input is high, the synchronous MOSFET is turned off and the control MOSFET is turned on. When PWM input is low, control MOSFET is turned off and synchronous MOSFET is turned on. Figures 16-18 show the PWM input and the corresponding SW and GATEL output. If PWM pin is floated , the built-in resistors pull the PWM pin into a tri-state region centered around 1.65V. When PWM input voltage is in tri-state region, the IR3551 will go into either Body-Braking(R) mode or diode emulation mode depending on BBRK# selection during VCC power up. BODY-BRAKING(R) MODE The IR3551 accepts an active low Body-Braking(R) input which disables both MOSFETs to enhance transient performance or provide a high impedance output. The IR3551 provides diode emulation feature which avoids negative current in the synchronous MOSFET and improves light load efficiency. The IR3551 PWM input is compatible with 3.3V logic signal and 7V tolerant. It accepts 3-level PWM input signals with tri-state. BBRK# PIN FUNCTIONS The BBRK# pin has two functions. During normal operation, it accepts direct control signal from the PWM controller to enable Body-Braking(R), which turns off both control and synchronous MOSFETs to improve the load transient response. The second function of BBRK# pin is to select BodyBraking(R) (tristate) or diode emulation mode when PWM pin receives a tri-state signal. The seletion is recongnized right after VCC passes its UVLO threshold during the VCC power up. If the BBRK# input is always high, the default operation mode is Body- Braking(R), in which both MOSFETs will be turned off when the PWM input is in tri-state. If the BBRK# input has been pulled low for at least 20ns after the VCC passes its UVLO threshold during power up, the diode emulation mode is set. PWM input in tri-state will activate 13 July 16, 2013 | DATASHEET V3.2 International Rectifier's Body-Braking(R) is an operation mode in which two MOSFETs are turned off. When the synchronous MOSFET is off, the higher voltage across the Shottky diode in parallel helps discharging the inductor current faster, which reduces the output voltage overshoot. The Body-Braking(R) can be used either to enhance transient response of the converter after load release or to provide a high impedance output. There are two ways to place the IR3551 in Body-Braking(R) mode, either controlling the BBRK# pin directly or through a PWM tri-state signal. Both control signals are usually from the PWM controller. Pulling BBRK# low forces the IR3551 into Body-Braking(R) mode rapidly, which is usually used to enhance converter transient response after load release, as shown in Figure 19. Releasing BBRK# forces the IR3551 out of BodyBraking(R) mode quickly. The BBRK# low turns off both MOSFETs and therefore can also be used to disable a converter. Please note that soft start may not be available when BBRK# is pulled high to enable the converter. If the BBRK# input is always high, the Body-Braking(R) is activated when the PWM input enters the tri-state region, as shown in Figures 20 and 21. Comparing to pulling down the BBRK# pin directly, the Body-Braking(R) response to PWM tri-state signal is slower due to the hold-off time 50A Integrated PowIRstage(R) created by the PWM pin parasitic capacitor with the pullup and pull-down resistors of PWM pin. For better performance, no more than 100pF parasitic capacitive load should be present on the PWM line of IR3551. SYNCHRONOUS DIODE EMULATION MODE An additional feature of the IR3551 is the synchronous diode emulation mode. This function enables increased efficiency by preventing negative inductor current from flowing in the synchronous MOSFET. As shown in Figure 22, when the PWM input enters the tristate region the control MOSFET is turned off first, and the synchronous MOSFET is initially turned on and then is turned off when the output current reaches zero. If the sensed output current does not reach zero within a set amount of time the gate driver will assume that the output is de-biased and turn off the synchronous MOSFET, allowing the switch node to float. This is in contrast to the Body-Braking(R) mode shown in Figure 23, where GATEL follows PWM input. The Schottky diode in parallel with the synchronous MOSFET conducts for a longer period of time and therefore lowers the light load efficiency. The zero current detection circuit in the IR3551 is independent of the current sense amplifier and therefore still functions even if the current sense amplifier is not used. As shown in Figure 6, an offset is added to the diode emulation comparator so that a slightly positive output current in the inductor and synchronous MOSFET is treated as zero current to accommodate propagation delays, preventing any negative current flowing in the synchronous MOSFET. This causes the Schottky diode in parallel with the synchronous MOSFET to conduct before the inductor current actually reaches zero, and the conduction time increases with inductance of the output inductor. To set the IR3551 in diode emulation mode, the BBRK# pin must be toggled low at least once after the VCC passes its UVLO threshold during power up. One simple way is to use the internal BBRK# pull-up resistor (200k typical) with an external capacitor from BBRK# pin to LGND, as shown in Figure 4. To ensure the diode emulation mode is properly set, the BBRK# voltage should be lower than 0.8V when the VCC voltage passes its UVLO threshold (3.3V minimum and 3.7V typical), as shown in Figure 24. A digital signal from the PWM controller can also be used to set the diode emulation mode. The BBRK# signal can either be pulled low for at least 20ns after the VCC passes its UVLO 14 July 16, 2013 | DATASHEET V3.2 IR3551 threshold, as shown in Figure 25, or be pulled low before VCC power up and then released after the VCC passes its UVLO threshold, as shown in Figure 26. Once the diode emulation mode is set, it cannot be reset until the VCC power is recycled. PHASE FAULT AND THERMAL FLAG OUTPUT The phase fault circuit looks at the switch node with respect to ground to determine whether there is a defective MOSFET in the phase. The output of the phase fault signal is high during normal operation and is pulled low when there is a fault. Each driver monitors the MOSFET it drives. If the switch node is less than a certain voltage above ground when the PWM signal goes low or if the switch node is a certain voltage above ground when the PWM signal rises, this gives a fault signal. If there are a number of consecutive faults the phase fault signal is asserted. Thermal flag circuit monitors the temperature of the IR3551. If the temperature goes above a threshold (160C typical) the PHSFLT# pin is pulled low after a maximum delay of 100us. The PHSFLT# pin can be pulled low by either the phase fault circuit or the thermal flag circuit, but the IR3551 relies on the system to take protective actions. The phase fault signal could be used by the system to turn off the AC/DC converter or blow a fuse to disconnect the DC/DC converter input from the supply. If PHSFLT# is not used it can be floated or connected to LGND. LOSSLESS AVERAGE INDUCTOR CURRENT SENSING Inductor current can be sensed by connecting a series resistor and a capacitor network in parallel with the inductor and measuring the voltage across the capacitor, as shown in Figure 31. The equation of the current sensing network is as follows. vCS ( s ) vL ( s ) 1 1 sRCS CCS L RL iL ( s ) RL 1 sRCS CCS iL ( s) RL when L RL RCSCCS 1 s 50A Integrated PowIRstage(R) IR3551 VIN VIN CIN + vL - L SW RL iL RCS Current Sense Amplifier CCS VOUT COUT + vCS + CSIN+ - CSIN- Figure 31: Inductor current sensing Usually the resistor RCS and capacitor CCS are chosen so that the time constant of RCS and CCS equals the inductor time constant, which is the inductance L over the inductor DCR (RL). If the two time constants match, the voltage across CCS is proportional to the current through L, and the sense circuit can be treated as if only a sense resistor with the value of RL was used. The mismatch of the time constants does not affect the measurement of inductor DC current, but affects the AC component of the inductor current. The advantage of sensing the inductor current versus high side or low side sensing is that actual output current being delivered to the load is obtained rather than peak or sampled information about the switch currents. The output voltage can be positioned to meet a load line based on real time information. This is the only sense method that can support a single cycle transient response. Other methods provide no information during either load increase (low side sensing) or load decrease (high side sensing). CURRENT SENSE AMPLIFIER IR3551 summed with the reference voltage REFIN and sent to the IOUT pin. The REFIN voltage is to ensure at light loads there is enough output range to accommodate the negative current ripple shown in Figure 28. In a multiphase converter, the IOUT pins of all the phases can be tied together through resistors, and the IOUT voltage represents the average current through all the inductors and is used by the controller for adaptive voltage positioning. The input offset voltage is the primary source of error for the current signal. In order to obtain very accurate current signal, the current sense amplifier continuously calibrates itself, and the input offset of this amplifier is within +/450uV. This calibration algorithm can create a small ripple on IOUT with a frequency of fsw/128. If the IR3551 current sense amplifier is required, connect its output IOUT and the reference voltage REFIN to the PWM controller and connect the inductor sense circuit as shown in Figure 4. If the current sense amplifier is not needed, tie CSIN+, CSIN- and REFIN pins to LGND and float IOUT pin, as shown in Figure 5. MAXIMUM OUTPUT VOLTAGE When the IR3551 current sense amplifier is used, the maximum output voltage is limited by the VCC voltage used and should be lower than VCC - 2.5V to ensure enough headroom for the current sense amplifier. The maximum voltage is 4.3V when 6.8V VCC is used, but is only 2.5V when 5V VCC is used. When the IR3551 current sense amplifier is not used, the maximum voltage is not limited by the VCC voltage. The IR3551 can support output voltage up to 5.5V but the output current must be derated since the MOSFET ratio was optimized for duty cycles of 10% to 20%. A high speed differential current sense amplifier is located in the IR3551, as shown in Figure 6. Its gain is nominally 32.5, and the inductor DCR increase with temperature is not compensated inside the IR3551. The current sense amplifier output IOUT is referenced to REFIN, which is usually connected to a reference voltage from the PWM controller. Figure 27 shows the differential voltage of V(IOUT) - V(REFIN) versus the inductor current and reflects the inductor DCR increase with temperature at higher current. DESIGN PROCEDURES The current sense amplifier can accept positive differential input up to 25mV and negative input up to -10mV before clipping. The output of the current sense amplifier is Where both MOSFET loss and the driver loss are included, but the PWM controller and the inductor losses are not included. 15 July 16, 2013 | DATASHEET V3.2 POWER LOSS CALCULATION The single-phase IR3551 efficiency and power loss measurement circuit is shown in Figure 32. The IR3551 power loss is determined by, PLOSS VIN I IN VCC IVCC VSW I OUT 50A Integrated PowIRstage(R) C3 1uF VCC IVCC IIN VIN VCC PHSFLT# BOOST PWM BBRK# REFIN Determine the output voltage normalizing factor with VOUT=1V, which is 0.92 based on the dashed lines in Figure 11. C5 0.22uF 4) Determine the switching frequency normalizing factor with SW = 300kHz, which is 0.99 based on the dashed lines in Figure 12. 5) Determine the VCC MOSFET drive voltage normalizing factor with VCC=5V, which is 1.18 based on the dashed lines in Figure 13. 6) Determine the inductance normalizing factor with L=210nH, which is 0.94 based on the dashed lines in Figure 14. 7) Multiply the power loss under the default conditions by the five normalizing factors to obtain the power loss under the new conditions, which is 4.5W x 0.96 x 0.92 x 0.99 x 1.18 x 0.94 = 4.4W. C2 47uF x4 L1 150nH IOUT VOUT SW LGND C7 1nF 3) VIN C1 0.22uF IR3551 R1 10k CSIN+ R2 2.49k C6 470uF x3 C4 0.22uF CSINIOUT IR3551 PGND VSW Figure 32: IR3551 Power Loss Measurement Figure 7 shows the measured single-phase IR3551 efficiency under the default test conditions, VIN=12V, VOUT=1.2V, SW = 400kHz, L=150nH (0.29m), VCC=7V, TAMBIENT = 25C, no heat sink, and no air flow. The efficiency of an interleaved multiphase IR3551 converter is always higher than that of a single-phase under the same conditions due to the reduced input RMS current and more input/output capacitors. The measured single-phase IR3551 power loss under the same conditions is provided in Figure 8. If any of the application condition, i.e. input voltage, output voltage, switching frequency, VCC MOSFET driver voltage or inductance, is different from those of Figure 8, a set of normalized power loss curves should be used. Obtain the normalizing factors from Figure 10 to Figure 14 for the new application conditions; multiply these factors by the power loss obtained from Figure 8 for the required load current. As an example, the power loss calculation procedures under different conditions, VIN=10V, VOUT=1V, SW = 300kHz, VCC=5V, L=210nH, VCC=5V, IOUT=35A, TAMBIENT = 25C, no heat sink, and no air flow, are as follows. 1) 2) Determine the power loss at 35A under the default test conditions of VIN=12V, VOUT=1.2V, SW = 400kHz, L=150nH, VCC=7V, TAMBIENT = 25C, no heat sink, and no air flow. It is 4.5W from Figure 8. Determine the input voltage normalizing factor with VIN=10V, which is 0.96 based on the dashed lines in Figure 10. 16 July 16, 2013 | DATASHEET V3.2 THERMAL DERATING Figure 9 shows the IR3551 thermal derating curve with the case temperature controlled at or below 125C. The test conditions are VIN=12V, VOUT=1.2V, SW=400kHz, L=150nH (0.29m), VCC=7V, TAMBIENT = 0C to 90C, with and without heat sink, and Airflow = 0LFM /100LFM /200LFM /400LFM. If any of the application condition, i.e. input voltage, output voltage, switching frequency, VCC MOSFET driver voltage, or inductance is different from those of Figure 9, a set of IR3551 case temperature adjustment curves should be used. Obtain the temperature deltas from Figure 10 to Figure 14 for the new application conditions; sum these deltas and then subtract from the IR3551 case temperature obtained from Figure 9 for the required load current. 8) From Figure 9, determine the maximum current at the required ambient temperature under the default conditions, which is 42A at 45C with 0LFM airflow and the IR3550 case temperature of 125C. 9) Determine the case temperature with VIN=10V, which is -0.9 based on the dashed lines in Figure 10. 10) Determine the case temperature with VOUT=1V, which is -1.8 based on the dashed lines in Figure 11. 11) Determine the case temperature with SW = 300kHz, which is -0.2 based on the dashed lines in Figure 12. 50A Integrated PowIRstage(R) 12) Determine the case temperature with VCC = 5V, which is +4.0 based on the dashed lines in Figure 13. 13) Determine the case temperature with L=210nH, which is -1.4 based on the dashed lines in Figure 14. 14) Sum the case temperature adjustment from 9) to 13), -0.9 -1.8 -02 +4.0 -1.4 = -0.3. Add the delta to the required ambient temperature in step 8), 45C + (0.3C) = 44.7C, at which the maximum current is reduced to 43A when the allowed junction temperature is 125C, as shown in Figure 9. If only 105C junction temperature is allowed, the required ambient temperature is equivalent to 44.7C + (125C 105C) = 64.7C, which indicates 37A maximum current at the 45C required ambient temperature. INDUCTOR CURRENT SENSING CAPACITOR CCS AND RESISTOR RCS If the IR3551 is used with inductor DCR sensing, care must be taken in the printed circuit board layout to make a Kelvin connection across the inductor DCR. The DC resistance of the inductor is utilized to sense the inductor current. Usually the resistor RCS and capacitor CCS in parallel with the inductor are chosen to match the time constant of the inductor, and therefore the voltage across the capacitor CCS represents the inductor current. Measure the inductance L and the inductor DC resistance RL. Pre-select the capacitor CCS and calculate RCS as follows. RCS L RL C CS INPUT CAPACITORS CVIN At least two 10uF 1206 ceramic capacitors and one 0.22uF 0402 ceramic capacitor are recommended for decoupling the VIN to PGND connection. The 0.22uF 0402 capacitor should be on the same side of the PCB as the IR3551 and next to the VIN and PGND pins. Adding additional capacitance and use of capacitors with lower ESR and mounted with low inductance routing will improve efficiency and reduce overall system noise, especially in single-phase designs or during high current operation. BOOTSTRAP CAPACITOR CBOOST A minimum of 0.22uF 0402 capacitor is required for the bootstrap circuit. A high temperature 0.22uF or greater value 0402 capacitor is recommended. It should be mounted on the same side of the PCB as the IR3551 and as close as possible to the BOOST pin. A low-inductance PCB 17 July 16, 2013 | DATASHEET V3.2 IR3551 routing of the SW pin connection to the other terminal of the bootstrap capacitor is required to minimize the ringing between the BOOST and SW pins. VCC DECOUPLING CAPACITOR CVCC A 0.22uF to 1uF ceramic decoupling capacitor is required at the VCC pin. It should be mounted on the same side of the PCB as the IR3551 and as close as possible to the VCC and PGND (pin 4). Low inductance routing between the VCC capacitor and the IR3551 pins is strongly recommended. BODY-BRAKING(R) PIN FUNCTION The BBRK# pin should be pulled up to VCC if the feature is not used by the PWM controller. Use of a 4.7k resistor or a direct connection to VCC is recommended. MOUNTING OF HEAT SINKS Care should be taken in the mounting of heat sinks so as not to short-circuit nearby components. The VCC and Bootstrap capacitors are typically mounted on the same side of the PCB as the IR3551. The mounting height of these capacitors must be considered when selecting their package sizes. HIGH OUTPUT VOLTAGE DESIGN CONSIDERATIONS The IR3551 is capable of creating output voltages above the 3.3V recommended maximum output voltage as there are no restrictions inside the IR3551 on the duty cycle applied to the PWM pin. However if the current sense feature is required, the common mode range of the current sense amplifier inputs must be considered. A violation of the current sense input common mode range may cause unexpected IR3551 behavior. Also the output current rating of the device will be reduced as the duty cycle increases. In very high duty cycle applications sufficient time must be provided for replenishment of the Bootstrap capacitor for the control MOSFET drive. LAYOUT EXAMPLE Contact International Rectifier for a layout example suitable for your specific application. 50A Integrated PowIRstage(R) IR3551 METAL AND COMPONENT PLACEMENT Lead land width should be equal to nominal part lead width. The minimum lead to lead spacing should be 0.2mm to prevent shorting. Lead land length should be equal to maximum part lead length +0.15 - 0.3 mm outboard extension and 0 to + 0.05mm inboard extension. The outboard extension ensures a large and visible toe fillet, and the inboard extension will accommodate any part misalignment and ensure a fillet. Center pad land length and width should be equal to maximum part pad length and width. Only 0.30mm diameter via shall be placed in the area of the power pad lands and connected to power planes to minimize the noise effect on the IC and to improve thermal performance. Figure 33: Metal and component placement * Contact International Rectifier to receive an electronic PCB Library file in Cadence Allegro or CAD DXF/DWG format. 18 July 16, 2013 | DATASHEET V3.2 50A Integrated PowIRstage(R) SOLDER RESIST The solder resist should be pulled away from the metal lead lands by a minimum of 0.06mm. The solder resist miss-alignment is a maximum of 0.05mm and it is recommended that the low power signal lead lands are all Non Solder Mask Defined (NSMD). Therefore pulling the S/R 0.06mm will always ensure NSMD pads. The minimum solder resist width is 0.13mm typical. The dimensions of power land pads, VIN, PGND, TGND and SW, are Non Solder Mask Defined (NSMD). The equivalent PCB layout becomes Solder Mask Defined (SMD) after power shape routing. Ensure that the solder resist in-between the lead lands and the pad land is 0.15mm due to the high aspect ratio of the solder resist strip separating the lead lands from the pad land. At the inside corner of the solder resist where the lead land groups meet, it is recommended to provide a fillet so a solder resist width of 0.17mm remains. Figure 34: Solder resist * Contact International Rectifier to receive an electronic PCB Library file in Cadence Allegro or CAD DXF/DWG format. 19 July 16, 2013 | DATASHEET V3.2 IR3551 50A Integrated PowIRstage(R) IR3551 STENCIL DESIGN The stencil apertures for the lead lands should be approximately 65% to 75% of the area of the lead lands depending on stencil thickness. Reducing the amount of solder deposited will minimize the occurrence of lead shorts. Since for 0.5mm pitch devices the leads are only 0.25mm wide, the stencil apertures should not be made narrower; openings in stencils < 0.25mm wide are difficult to maintain repeatable solder release. The low power signal stencil lead land apertures should therefore be shortened in length to keep area ratio of 65% to 75% while centered on lead land. The power pads VIN, PGND, TGND and SW, land pad apertures should be approximately 65% to 75% area of solder on the center pad. If too much solder is deposited on the center pad the part will float and the lead lands will be open. Solder paste on large pads is broken down into small sections with a minimum gap of 0.2mm between allowing for out-gassing during solder reflow. The maximum length and width of the land pad stencil aperture should be equal to the solder resist opening minus an annular 0.2mm pull back to decrease the incidence of shorting the center land to the lead lands when the part is pushed into the solder paste. Figure 35: Stencil design * Contact International Rectifier to receive an electronic PCB Library file in Cadence Allegro or CAD DXF/DWG format. 20 July 16, 2013 | DATASHEET V3.2 50A Integrated PowIRstage(R) MARKING INFORMATION Site/Date/Marking Code Lot Code 3551M ?YWW? xxxx Figure 36: PQFN 5mm x 6mm PACKAGE INFORMATION Figure 37: PQFN 5mm x 6mm 21 July 16, 2013 | DATASHEET V3.2 IR3551 50A Integrated PowIRstage(R) IR3551 Data and specifications subject to change without notice. This product will be designed and qualified for the Industrial market. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information. www.irf.com 22 July 16, 2013 | DATASHEET V3.2