EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 1 of 10
Device No. : SZDSE-175-G11 Prepared date:27-Feb-2007 Prepared by:ZhangQiang
Technical Data Sheet
0805 Package Chip LED (0.8mm Height)
17-215/G6C –FN2P2L/3T
Features
˙Package in 8mm tape on 7〞diameter reel.
˙Compatible with automatic placement equipment.
˙Compatible with infrared and vapor phase reflow
solder process.
˙Mono-color type.
˙Pb-free.
˙The product itself will remain within RoHS compliant version
Descriptions
˙The 17-215 SMD Taping is much smaller than
lead frame type components, thus enable smaller
board size, higher packing density, reduced storage
space and finally smaller equipment to be
obtained.
˙Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
˙Backlighting in dashboard and switch.
˙Telecommunication: indicator and backlighting in
telephone and fax.
˙Flat backlight for LCD, switch and symbol.
˙General use.
Device Selection Guide
Chip
Part No. Material Emitted Color Resin Color
17-215/G6C-FN2P2L/3T AlGaInP
Brilliant Yellow
Green Water Clear
EVERLIGHT ELECTRONICS CO.,LTD.
17-215/G6C-FN2P2L/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 2 of 10
Device No. : SZDSE-175-G11 Prepared date:27-Feb-2007 Prepared by:ZhangQiang
Package Outline Dimensions
Note: The tolerances unless mentioned are ±0.1mm ,Unit = mm
EVERLIGHT ELECTRONICS CO.,LTD.
17-215/G6C-FN2P2L/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 3 of 10
Device No. : SZDSE-175-G11 Prepared date:27-Feb-2007 Prepared by:ZhangQiang
Absolute Maximum R atings (Ta=25℃)
Parameter Symbol Rating Unit
Reverse Voltage VR 5 V
Forward Current IF 25 mA
Peak Forward Current
(Duty 1/10 @1KHz) IFP 60 mA
Power Dissipation Pd 60 mW
Electrostatic Discharge(HBM) ESD 2000 V
Operating Temperature Topr -40 ~ +85 ℃
Storage Temperature Tstg -40 ~ +90 ℃
Soldering Temperature Tsol Reflow Soldering : 260 ℃ for 10 sec.
Hand Soldering : 350 ℃ for 3 sec.
Electro-Optical Characteristics (Ta=25℃)
Parameter Symbol Min. Typ. Max. Unit Condition
Luminous Intensity Iv 36.0 ----- 72.0 mcd
Viewing Angle 2θ1/2 ----- 130 ---- deg
Peak Wavelength λp ---- 575 ---- nm
Dominant
Wavelength λd 570.0 ---- 574.5 nm
Spectrum Radiation
Bandwidth △λ ----- 20 ---- nm
Forward Voltage VF 1.70 ---- 2.30 V
IF =20mA
Reverse Current IR ---- ---- 10 μA VR=5V
Notes:
1.Tolerance of Luminous Intensity ±11%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.05V
EVERLIGHT ELECTRONICS CO.,LTD.
17-215/G6C-FN2P2L/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 4 of 10
Device No. : SZDSE-175-G11 Prepared date:27-Feb-2007 Prepared by:ZhangQiang
Bin Range Of Dom. Wavelength
Group Bin Min Max Unit Condition
CC2 570.0 571.5
CC3 571.5 573.0
F
CC4 573.0 574.5
nm IF =20mA
Bin Range Of Luminous Intensity
Bin Min Max Unit Condition
N2 36.0 45.0
P1 45.0 57.0
P2 57.0 72.0
mcd IF =20mA
Bin Range Of Luminous Voltage
Group Bin Min Max Unit Condition
19 1.70 1.80
20 1.80 1.90
21 1.90 2.00
22 2.00 2.10
23 2.10 2.20
L
24 2.20 2.30
V IF =20mA
Notes:
1.Tolerance of Luminous Intensity ±11%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.05V
EVERLIGHT ELECTRONICS CO.,LTD.
17-215/G6C-FN2P2L/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 5 of 10
Device No. : SZDSE-175-G11 Prepared date:27-Feb-2007 Prepared by:ZhangQiang
Typical Electro-Optical Characteristics Curves
EVERLIGHT ELECTRONICS CO.,LTD.
17-215/G6C-FN2P2L/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 6 of 10
Device No. : SZDSE-175-G11 Prepared date:27-Feb-2007 Prepared by:ZhangQiang
xxxxxx
xxxxxx
xxxxxxxxxxxx
xxxx
xxxxxxxx
RoHS
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
EVERLIGHT ELECTRONICS CO.,LTD.
17-215/G6C-FN2P2L/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 7 of 10
Device No. : SZDSE-175-G11 Prepared date:27-Feb-2007 Prepared by:ZhangQiang
Carrier Tape Dim e nsions: Loaded quantity 3000PCS per reel
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Moisture Resistant Pack aging
Label Aluminum moisture-proof bag Desiccant Label
EVERLIGHT ELECTRONICS CO.,LTD.
17-215/G6C-FN2P2L/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 8 of 10
Device No. : SZDSE-175-G11 Prepared date:27-Feb-2007 Prepared by:ZhangQiang
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level：90%
LTPD：10%
No. Items Test Condition
Test
Hours/Cycles Sample
Size Ac/Re
1 Reflow Soldering
Temp. : 260℃±5℃
Min. 5sec. 6 Min. 22 PCS. 0/1
2 Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles 22 PCS. 0/1
3 Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles 22 PCS. 0/1
4 High Tem perature
Storage Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1
5 Low Temperature
Storage Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1
6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1
7 High Tem perature /
High Humidity 85℃/ 85% RH 1000 Hrs. 22 PCS. 0/1
EVERLIGHT ELECTRONICS CO.,LTD.
17-215/G6C-FN2P2L/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 9 of 10
Device No. : SZDSE-175-G11 Prepared date:27-Feb-2007 Prepared by:ZhangQiang
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
EVERLIGHT ELECTRONICS CO.,LTD.
17-215/G6C-FN2P2L/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev.1 Page: 10 of 10
Device No. : SZDSE-175-G11 Prepared date:27-Feb-2007 Prepared by:ZhangQiang
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of the
hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., L TD. Tel: 886-2-2267-2000, 2267-9936
Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306
Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com
