AH22S High Dynamic Range CATV Amplifier Product Features Product Description * 50 - 1000 MHz * 0.2 dB Gain Flatness * +25 dBm P1dB * -74 dBc CTB / CSO +39dBmV/channel, 77 channels Applications * CATV Head End Equipment * CATV Line Amplifiers * FTTH Repeaters The device uses two matched devices and is ideal for operation in a push-pull configuration to achieve high second order linearity. A mature and reliable GaAs MESFET technology is employed to maximize linearity at low power dissipation. The dual amplifier is housed in an industry standard surface-mount SOIC-8 package with all devices being 100% RF and dc tested. This device is available in a lead-free/green/RoHS-compliant package with NiPdAu plating material on the leads. It is compatible with both lead-free and lead soldering processes. Single-ended Device Specifications (1) Operational Bandwidth Test Frequency Gain Output IP3 (2) Device Current Device Voltage Functional Diagram The AH22S is a high dynamic range amplifier targeting cable TV markets. The combination of gain flatness, high linearity, and bandwidth makes it ideal for CATV distribution, cable modem, and laser diode driver applications. * +43 dBm Output IP3 * +77 dBm Output IP2 * Matched amplifiers for a pushpull configuration * +5V Single Positive Supply * MTTF > 1000 years Parameter Product Information Units Min MHz MHz dB dBm mA V Typ 50 13 +37 120 Max 1000 800 14.5 +40 160 5 190 1. Test conditions unless otherwise noted: 25 C, Vd = +5 V, 800 MHz on each individual singlebranch amplifier in a 50 test fixture. 2. 3OIP measured with two tones at an output power of +5 dBm/tone separated by 10 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. 3. Typical parameters reflect performance in a push-pull application circuit as shown on page 3. Note that the feedback resistance values are R1 = R2 = 560. 4. Balun, board, and connector losses have not been extracted, but typically account of 0.4 dB loss midband and 1.1 dB loss at 860 MHz. 5. Measured at +39 dBmV/channel, 77 channels Flat Loading. 6. OIP2 is measured at f1 + f2 at +8 dBm / tone. 7. OIP3 is measured at 8 dBm / tone with 10 MHz spacing. 1 8 2 7 3 6 4 5 Function Amp 1 Input Amp 2 Input Amp 2 Output Amp 1 Output Pin No. 1 4 5 8 2, 3, 6, 7, Backside paddle Ground Typical Performance (3) Parameter Units Frequency Gain (4) Input Return Loss Output Return Loss CTB (5) CSO (5) XMOD (5) Output P1dB Output IP2 (6) Output IP3 (7) Noise Figure Device Bias MHz dB dB dB dBc dBc dBc dBm dBm dBm dB V Typical 50 11.3 10.6 17.1 -75 -73 -63 +25.9 +79 +43 6.1 250 450 860 11.1 11.1 11.1 10.4 11.6 15.8 15.4 15.4 18.2 -74 -74 -86 -77 -63 -63 +26 +25.5 +24.7 +77 +77 +76 +45 +42 +42 4.6 4.5 4.2 +5 V @ 320 mA Absolute Maximum Rating Parameter Operating Case Temperature Storage Temperature Supply Voltage RF Input Power (continuous) Junction Temperature Rating -40 to +85 C -55 to +150 C +6 V +13 dBm +220 C Ordering Information Part No. AH22S-G Description High Dynamic Range CATV Amplifier (lead-free/green/RoHS-compliant SOIC8 Pkg) AH22S-PCB Push-pull CATV Evaluation Board Operation of this device above any of these parameters may cause permanent damage. Specifications and information are subject to change without notice. WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com, www.TriQuint.com Page 1 of 4 April 2006 AH22S High Dynamic Range CATV Amplifier Product Information Typical Device Data - 50 Zo S-Parameters (Vds = +5 V, Ids = 160 mA, T = 25 C, unmatched 50 ohm system, calibrated to device leads) This data represents a single-ended amplifier in the AH22S, with there being two matched amplifiers inside the package. Freq (MHz) S11 (dB) S11 (ang) S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) 50 -7.94 -19.61 15.23 168.38 -21.82 1.63 -15.80 -30.57 100 -8.21 -19.49 15.08 167.60 -21.70 -2.29 -16.57 -23.98 150 -8.22 -22.08 15.09 165.36 -21.79 -4.14 -16.83 -22.42 200 -8.25 -25.88 15.06 162.70 -21.72 -5.10 -17.08 -22.40 250 -8.21 -29.76 15.07 160.34 -21.71 -6.46 -17.15 -24.78 300 -8.23 -34.25 15.03 157.80 -21.68 -7.08 -17.08 -26.62 350 -8.23 -38.03 14.97 155.21 -21.61 -8.03 -17.41 -28.61 400 -8.26 -42.15 14.91 152.90 -21.62 -8.74 -17.56 -31.59 450 -8.21 -47.04 14.90 150.12 -21.57 -8.94 -17.49 -34.08 500 -8.17 -51.60 14.89 147.43 -21.58 -9.79 -17.75 -36.18 550 -8.11 -55.76 14.92 145.05 -21.53 -10.47 -17.80 -38.05 600 -8.14 -60.10 14.80 142.10 -21.47 -11.19 -18.07 -40.53 650 -8.13 -65.20 14.76 139.29 -21.49 -12.18 -18.25 -43.17 700 -8.02 -69.16 14.70 136.86 -21.41 -12.79 -18.42 -46.67 750 -8.04 -73.20 14.70 134.04 -21.38 -13.38 -18.69 -48.74 800 -8.02 -77.63 14.64 131.89 -21.30 -14.62 -18.86 -51.10 850 -7.98 -82.46 14.59 128.68 -21.26 -15.36 -18.96 -55.03 900 -7.91 -87.02 14.53 125.87 -21.16 -16.42 -19.19 -56.96 950 -7.86 -90.65 14.45 123.67 -21.12 -17.35 -19.48 -59.54 1000 -7.80 -94.58 14.39 121.33 -21.13 -18.12 -19.74 -63.18 Typical Device Data - 37.5 Zo S-Parameters (Vds = +5 V, Ids = 160 mA, T = 25 C, unmatched 37.5 ohm system, calibrated to device leads) This data represents a single-ended amplifier in the AH22S, with there being two matched amplifiers inside the package. Freq (MHz) S11 (dB) S11 (ang) S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) 50 -4.93 -12.81 14.35 170.16 -22.71 3.41 -9.19 -14.24 100 -5.09 -13.16 14.22 169.21 -22.57 -0.68 -9.40 -11.89 150 -5.12 -15.14 14.24 167.09 -22.64 -2.42 -9.51 -11.83 200 -5.17 -17.82 14.22 164.62 -22.55 -3.18 -9.61 -12.33 250 -5.18 -20.59 14.25 162.52 -22.53 -4.28 -9.66 -13.85 300 -5.23 -23.68 14.24 160.24 -22.47 -4.63 -9.66 -15.12 350 -5.28 -26.40 14.20 157.86 -22.38 -5.38 -9.83 -16.35 400 -5.36 -29.29 14.17 155.77 -22.36 -5.87 -9.95 -17.91 450 -5.39 -32.75 14.19 153.27 -22.28 -5.79 -9.96 -19.42 500 -5.45 -36.09 14.22 150.79 -22.26 -6.43 -10.12 -20.68 550 -5.48 -39.19 14.28 148.61 -22.17 -6.90 -10.17 -21.94 600 -5.58 -42.45 14.20 145.83 -22.07 -7.46 -10.35 -23.33 650 -5.69 -46.33 14.21 143.20 -22.04 -8.27 -10.51 -24.87 700 -5.70 -49.50 14.18 140.95 -21.93 -8.70 -10.66 -26.61 750 -5.81 -52.71 14.22 138.23 -21.86 -9.19 -10.83 -27.82 800 -5.92 -56.28 14.21 136.19 -21.73 -10.32 -10.97 -29.22 850 -6.02 -60.34 14.21 133.11 -21.64 -10.93 -11.15 -31.33 900 -6.10 -64.31 14.21 130.38 -21.49 -11.90 -11.32 -32.62 950 -6.17 -67.57 14.17 128.23 -21.41 -12.79 -11.55 -33.86 1000 -6.26 -71.12 14.16 125.92 -21.37 -13.52 -11.80 -35.45 Specifications and information are subject to change without notice. WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com, www.TriQuint.com Page 2 of 4 April 2006 AH22S High Dynamic Range CATV Amplifier Product Information 75 Push-Pull Application Circuit Circuit Board Material: .062" total thickness with a .028" FR4 top RF layer (r=4.8), 4 total layers (other layers added for rigidity), 1 oz copper Typical RF Performance at 25C Frequency Gain Input R.L. Output R.L. CTB CSO XMOD Output P1dB Output IP2 Output IP3 Noise Figure Device Current Device Voltage MHz dB dB dB dBc dBc dBc dBm dBm dBm dB mA V 50 11.3 10.6 17.1 -75 -73 -63 +25.9 +79 +43 6.1 +5 V ID=C5 C=1000 pF ID=C3 C=100 pF 250 450 860 11.1 11.1 11.1 10.4 11.6 15.8 15.4 15.4 18.2 -74 -74 -86 -77 -63 -63 +26 +25.5 +24.7 +77 +77 +76 +45 +42 +42 4.6 4.5 4.2 320 +5 ID=R1 R=560 Ohm ID=C1 C=1.5 pF ID=L4 L=470 nH AH22S XFMR ID=L1 1 o ID=L2 L=5.6 nH 3 1 : n1 o 2 4 ID=C6 C=1000 pF ID=C7 C=1000 pF ID=L3 L=5.6 nH XFMR ID=L6 4 3 2 o o n1 : 1 1 ID=L5 L=470 nH CAP ID=C4 C=100 pF ID=C2 C=1.5 pF ID=C8 C=1000 pF +5 V ID=R2 R=560 Ohm 1. Balun, board, and connector losses have not been extracted, but typically account of 0.4 dB loss midband and 1.1 dB loss at 860 MHz. 2. CSO, CTB, & XMOD are measured at +39 dBmV/channel, 77 channels Flat Loading. 3. OIP2 is measured at f1 + f2 at 8 dBm / tone. 4. OIP3 is measured at 8 dBm / tone with 10 MHz spacing. The transformers, L1 and L6, used on the WJ evaluation board are handwound baluns using these materials: 6 turns bifilar wire (MWS B2383211) around a ferrite core (TDK, H5C2-T3.1-1.3-1.3). An SMT transformer (M/A Com ETC1-1-13) can also be used. Gain Return Loss 12 0 11 -5 S11 S22 -10 10 -15 9 -20 8 -25 -30 7 0 200 400 600 800 0 1000 200 400 600 800 1000 Frequency (MHz) Frequency (MHz) Noise Figure CSO, CTB, & XMOD +39 dBmV / channel, 77 channel flat loading 7 -50 XMOD 6 CTB CSO -60 5 -70 4 -80 3 2 -90 0 200 400 600 Frequency (MHz) 800 1000 0 100 200 300 400 500 600 Frequency (MHz) Specifications and information are subject to change without notice. WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com, www.TriQuint.com Page 3 of 4 April 2006 AH22S High Dynamic Range CATV Amplifier Product Information AH22S-G (Lead-Free Package) Mechanical Information This package is lead-free/green/RoHS-compliant. The plating material on the leads is NiPdAu. It is compatible with both lead-free (maximum 260 C reflow temperature) and lead (maximum 245 C reflow temperature) soldering processes. Outline Drawing Product Marking The component will be marked with an "AH22SG" designator with an alphanumeric lot code on the top surface of the package. The obsolete tin-lead package is marked with an "AH22S" designator followed by an alphanumeric lot code. Tape and reel specifications for this part are located on the website in the "Application Notes" section. ESD / MSL Information ESD Rating: Value: Test: Standard: Class 1B Passes from 500 to 1000 V Human Body Model (HBM) JEDEC Standard JESD22-A114 ESD Rating: Value Test: Standard: Class IV Passes greater than 1000 V Charge Device Model (CDM) JEDEC Standard JESD22-C101 MSL Rating: Level 2 at +260 C convection reflow Standard: JEDEC Standard J-STD-020A Functional Pin Layout Pin 1 2 3 4 5 6 7 8 Land Pattern Function RF input (Amp1 input) Ground Ground RF input (Amp2 input) RF output (Amp2 output) Ground Ground RF output (Amp1 output) The backside paddle is the Source and should be grounded for thermal and electrical purposes. Mounting Config. Notes Thermal Specifications Parameter Rating Operating Case Temperature Thermal Resistance (1), Rth Junction Temperature (2), Tj -40 to +85 C 28 C/W 130 C Notes: 1. The thermal resistance is referenced from the hottest part of the junction to ground tab underneath the device. 2. This corresponds to the typical biasing condition of +5V, 320 mA at an 85 C case temperature. A minimum MTTF of 1 million hours is achieved for junction temperatures below 160 C. MTTF vs. GND Tab Temperature 1. 1000 2. 100 3. 4. 10 5. 6. 1 60 70 80 90 100 Tab Temperature (C) 110 7. 8. 9. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80/.0135") diameter drill and have a final plated through diameter of .25mm (.010") Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. To ensure reliable operation, device ground paddle-to-ground pad solder joint is critical. Add mounting screws near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. For optimal thermal performance, expose soldermask on backside where it contacts the heatsink. RF trace width depends upon the PC board material and construction. Use 1 oz. Copper minimum. If the PCB design rules allow, ground vias should be placed under the land pattern for better RF and thermal performance. Otherwise ground vias should be placed as close to the land pattern as possible. All dimensions are in mm. Angles are in degrees. Specifications and information are subject to change without notice. WJ Communications, Inc * Phone 1-800-WJ1-4401 * FAX: 408-577-6621 * e-mail: sales@wj.com * Web site: www.wj.com, www.TriQuint.com Page 4 of 4 April 2006