NCP603 300 mA High Performance CMOS LDO Regulator with Enable and Enhanced ESD Protection http://onsemi.com The NCP603 provides 300 mA of output current at fixed voltage options, or an adjustable output voltage from 5.0 V down to 1.250 V. It is designed for portable battery powered applications and offers high performance features such as low power operation, fast enable response time, and low dropout. The device is designed to be used with low cost ceramic capacitors and is packaged in the TSOP-5/SOT23-5. 5 1 TSOP-5 SN SUFFIX CASE 483 Features * Output Voltage Options: * * * * * * * Adjustable, 1.3 V, 1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 3.5 V, 5.0 V Adjustable Output by External Resistors from 5.0 V down to 1.250 V Fast Enable Turn-on Time of 15 ms Wide Supply Voltage Range Operating Range Excellent Line and Load Regulation Typical Noise Voltage of 50 mVrms without a Bypass Capacitor Enhanced ESD Protection (HBM 3.5 kV, MM 400 V) These are Pb-Free Devices Typical Applications * * * * * MARKING DIAGRAM 5 xxx AYWG G 1 xxx A Y W G = Specific Device Code = Assembly Location = Year = Work Week = Pb-Free Package (Note: Microdot may be in either location) SMPS Post-Regulation Hand-held Instrumentation & Audio Players Noise Sensitive Circuits - VCO, RF Stages, etc. Camcorders and Cameras Portable Computing PIN CONNECTIONS VOUT VIN Vin 1 GND 2 ENABLE 3 5 Vout 4 ADJ/NC* Fixed Voltage Only (Top View) Driver w/ Current Limit GND + - + 1.25 V - * ADJ - Adjustable Version * NC - Fixed Voltage Version Thermal Shutdown ADJ Adjustable Version Only ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 12 of this data sheet. ENABLE Figure 1. Simplified Block Diagram (c) Semiconductor Components Industries, LLC, 2008 August, 2008 - Rev. 1 1 Publication Order Number: NCP603/D NCP603 PIN FUNCTION DESCRIPTION Pin No. Pin Name 1 Vin Description 2 GND 3 ENABLE The Enable Input places the device into low-power standby when pulled to logic low (< 0.4 V). Connect to Vin if the function is not used. 4 ADJ/NC Output Voltage Adjust Input (Adjustable Version), No Connection (Fixed Voltage Versions) (Note 1) 5 Vout Positive Power Supply Input Power Supply Ground; Device Substrate Regulated Output Voltage 1. True no connect. Printed circuit board traces are allowable. ABSOLUTE MAXIMUM RATINGS Rating Symbol Value Unit Vin -0.3 to 6.5 V Vout, ENABLE, ADJ -0.3 to 6.5 (or Vin + 0.3) Whichever is Lower V TJ(max) 150 C TSTG -65 to 150 C ESD Capability, Human Body Model (Note 3) ESDHBM 3500 V ESD Capability, Machine Model (Note 3) ESDMM 400 V MSL MSL1/260 - Input Voltage (Note 2) Output, Enable, Adjustable Voltage Maximum Junction Temperature Storage Temperature Moisture Sensitivity Level Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 2. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area. 3. This device series incorporates ESD protection and is tested by the following methods: ESD Human Body Model tested per AEC-Q100-002 (EIA/JESD22-A114) ESD Machine Model tested per AEC-Q100-003 (EIA/JESD22-A115) Latchup Current Maximum Rating: v150 mA per JEDEC standard: JESD78. THERMAL CHARACTERISTICS Rating Symbol Thermal Characteristics, TSOP-5 (Note 4) Thermal Resistance, Junction-to-Air (Note 5) Value RqJA Unit C/W 215 4. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area. 5. Value based on copper area of 645 mm2 (or 1 in2) of 1 oz copper thickness. OPERATING RANGES (Note 6) Rating Symbol Min Max Unit Input Voltage (Note 7) Vin Adjustable Output Voltage (Adjustable Version Only) Vout 1.75 6 V 1.25 5.0 Output Current V Iout 0 300 mA Ambient Temperature TA -40 125 C 6. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area. 7. Minimum Vin = 1.75 V or (Vout + VDO), whichever is higher. http://onsemi.com 2 NCP603 ELECTRICAL CHARACTERISTICS (Vin = 1.750 V, Vout = 1.250 V, Cin = Cout =1.0 mF, for typical values TA = 25C, for min/max values TA = -40C to 125C, unless otherwise specified.) (Note 8) Characteristic Symbol Test Conditions Min Typ Max Unit Regulator Output (Adjustable Voltage Version) Output Voltage Vout Iout = 1.0 mA to 150 mA Vin = 1.75 V to 6.0 V, Vout = ADJ 1.231 (-1.5%) 1.250 1.269 (+1.5%) V Output Voltage Vout Iout = 1.0 mA to 300 mA Vin = 1.75 V to 6.0 V, Vout = ADJ = 1.25 V 1.213 (-3%) 1.250 1.287 (+3%) V Power Supply Ripple Rejection (Note 9) PSRR Iout = 1.0 mA to 150 mA Vin = Vout + 1 V + 0.5 Vp-p f = 120 Hz f = 1.0 kHz f = 10 kHz dB - - - 62 55 38 - - - Line Regulation Regline Vin = 1.750 V to 6.0 V, Iout = 1.0 mA - 1.0 10 mV Load Regulation Regload Iout = 1.0 mA to 300 mA - 2.0 45 mV f = 10 Hz to 100 kHz - 50 - mVrms 350 650 900 mA Output Noise Voltage (Note 9) Vn Output Short Circuit Current Isc Dropout Voltage 1.25 V VDO Measured at: Vout - 2.0%, Iout = 150 mA, Figure 2 - 175 250 Dropout Voltage 1.25 V VDO Measured at: Vout - 2.0%, Iout = 300 mA, Figure 2 - 375 480 300 650 - Output Current Limit (Note 9) Iout(max) mV mV mA Regulator Output (Fixed Voltage Version) (Vin = Vout + 0.5 V, Cin = Cout =1.0 mF, for typical values TA = 25C, for min/max values TA = -40C to 125C; unless otherwise noted.) (Note 8) Output Voltage 1.3 V 1.5 V 1.8 V 2.5 V 2.8 V 3.0 V 3.3 V 3.5 V 5.0 V Vout Iout = 1.0 mA to 150 mA Vin = (Vout + 0.5 V) to 6.0 V (-2%) 1.270 1.470 1.764 2.450 2.744 2.940 3.234 3.430 4.900 1.3 1.5 1.8 2.5 2.8 3.0 3.3 3.5 5.0 (+2%) 1.326 1.530 1.836 2.550 2.856 3.060 3.366 3.570 5.100 V Output Voltage 1.3 V 1.5 V 1.8 V 2.5 V 2.8 V 3.0 V 3.3 V 3.5 V 5.0 V Vout Iout = 1.0 mA to 300 mA Vin = (Vout + 0.5 V) to 6.0 V (-3%) 1.261 1.455 1.746 2.425 2.716 2.910 3.201 3.395 4.850 1.3 1.5 1.8 2.5 2.8 3.0 3.3 3.5 5.0 (+3%) 1.339 1.545 1.854 2.575 2.884 3.090 3.399 3.605 5.150 V PSRR Iout = 1.0 mA to 150 mA Vin = Vout + 1 V + 0.5 Vp-p f = 120 Hz f = 1.0 kHz f = 10 kHz Power Supply Ripple Rejection (Note 9) dB - - - 62 55 38 - - - Line Regulation Regline Vin = 1.750 V to 6.0 V, Iout = 1.0 mA - 1.0 10 mV Load Regulation Regload Iout = 1.0 mA to 150 mA Iout = 1.0 mA to 300 mA - - 2.0 2.0 30 45 mV 8. Performance guaranteed over the indicated operating temperature range by design and/or characterization, production tested at TJ = TA = 25C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 9. Values based on design and/or characterization. http://onsemi.com 3 NCP603 ELECTRICAL CHARACTERISTICS (Vin = 1.750 V, Vout = 1.250 V (adjustable version)), (Vin = Vout + 0.5 V (fixed version)), Cin = Cout =1.0 mF, for typical values TA = 25C, for min/max values TA = -40C to 125C, unless otherwise specified.) (Note 10) Characteristic Symbol Output Noise Voltage (Note 11) Vn Output Short Circuit Current Isc Test Conditions f = 10 Hz to 100 kHz Dropout Voltage 1.3 V 1.5 V 1.8 V 2.5 V 2.7 V to 5.0 V VDO Measured at: Vout - 2.0% Iout = 150 mA Dropout Voltage 1.3 V 1.5 V 1.8 V 2.5 V 2.7 V to 5.0 V VDO Measured at: Vout - 2.0% Iout = 300 mA Output Current Limit (Note 11) Iout(max) Min Typ Max Unit - 50 - mVrms 350 650 900 mA - - - - - 175 150 125 85 75 250 225 175 175 125 - - - - - 375 350 245 187 157 480 400 340 275 230 300 650 - mA mV mV General Disable Current IDIS ENABLE = 0 V, Vin = 6 V -40C TA 85C - 0.01 1.0 mA Ground Current IGND ENABLE = 0.9 V, Iout = 1.0 mA to 300 mA - 145 180 mA Thermal Shutdown Temperature (Note 11) TSD - 175 - C Thermal Shutdown Hysteresis (Note 11) TSH - 10 - C ADJ Input Bias Current IADJ -0.75 - 0.75 mA Chip Enable ENABLE Input Threshold Voltage Vth(EN) V Voltage Increasing, Logic High 0.9 - - Voltage Decreasing, Logic Low - - 0.4 - 3.0 100 - - 15 30 25 50 Enable Input Bias Current (Note 11) IEN nA Timing Output Turn On Time (Note 11) 1.25 V to 3.5 V 5.0 V tEN ENABLE = 0 V to Vin ms 10. Performance guaranteed over the indicated operating temperature range by design and/or characterization, production tested at TJ = TA = 25C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 11. Values based on design and/or characterization. http://onsemi.com 4 NCP603 VIN 5 1 CIN 2 4 3 ENABLE VOUT COUT Figure 2. Typical Application Circuit for Vout = 1.250 V (Adjustable Version) VIN 5 1 CIN 2 R1 4 3 ENABLE VOUT COUT R2 Figure 3. Typical Application Circuit for Adjustable Vout VIN 5 1 CIN 2 VOUT COUT 4 3 Figure 4. Typical Application Circuit (Fixed Voltage Version) http://onsemi.com 5 NCP603 TYPICAL CHARACTERISTICS 1.256 1.260 Vout, OUTPUT VOLTAGE (V) Vout, OUTPUT VOLTAGE (V) 1.260 Iout = 1.0 mA 1.252 Iout = 150 mA 1.248 Vin = Vout + 0.5 V Vout = ADJ 1.244 1.240 -40 -20 0 20 40 60 80 -15 10 35 60 85 110 125 Figure 5. Output Voltage vs. Temperature (Vin = Vout + 0.5 V) Figure 6. Output Voltage vs. Temperature (Vin = 6.0 V) 1.500 Vout, OUTPUT VOLTAGE (V) Vout, OUTPUT VOLTAGE (V) Iout = 1.0 mA 1.490 Iout = 150 mA 1.485 1.480 -15 10 35 60 85 Iout = 1.0 mA 1.495 1.490 Iout = 150 mA 1.485 1.480 1.475 -40 110 125 -15 10 35 60 85 110 125 TA, TEMPERATURE (C) TA, TEMPERATURE (C) Figure 7. Output Voltage vs. Temperature (1.5 V Fixed Output, Vin = 2 V) Figure 8. Output Voltage vs. Temperature (1.5 V Fixed Output, Vin = 6 V) 3.005 3.005 Iout = 1.0 mA 3.000 2.995 Vout, OUTPUT VOLTAGE (V) Vout, OUTPUT VOLTAGE (V) Vin = 6.0 V Vout = ADJ 1.244 TA, TEMPERATURE (C) 1.495 Iout = 150 mA 2.990 2.985 2.980 2.975 -40 Iout = 150 mA 1.248 TA, TEMPERATURE (C) 1.500 1.475 -40 Iout = 1.0 mA 1.252 1.240 -40 120 100 1.256 -15 10 35 60 85 110 125 Iout = 1.0 mA 3.000 2.995 2.990 Iout = 150 mA 2.985 2.980 2.975 2.970 -40 TA, TEMPERATURE (C) -15 10 35 60 85 110 125 TA, TEMPERATURE (C) Figure 9. Output Voltage vs. Temperature (3.0 V Fixed Output, Vin = 3.5 V) Figure 10. Output Voltage vs. Temperature (3.0 V Fixed Output, Vin = 6 V) http://onsemi.com 6 NCP603 TYPICAL CHARACTERISTICS 5.000 Iout = 1.0 mA 4.995 4.990 Vout, OUTPUT VOLTAGE (V) Vout, OUTPUT VOLTAGE (V) 5.000 Iout = 150 mA 4.985 4.980 4.975 4.970 4.965 -40 -15 10 35 60 110 125 85 Iout = 1.0 mA 4.995 4.990 4.985 Iout = 150 mA 4.980 4.975 4.970 4.965 -40 -15 10 TA, TEMPERATURE (C) 110 125 250 Vout = ADJ 200 VDO, DROPOUT VOLTAGE (mV) Iout = 150 mA 150 100 Iout = 50 mA 50 0 -40 -20 Iout = 1.0 mA 0 20 40 60 80 100 Iout = 150 mA Vout = 1.25 V 200 1.50 V 1.80 V 150 2.80 V 100 3.00 V 50 5.00 V 0 -40 -20 120 0 20 40 60 80 100 120 TA, TEMPERATURE (C) TA, TEMPERATURE (C) Figure 13. Dropout Voltage vs. Temperature (Over Current Range) Figure 14. Dropout Voltage vs. Temperature (Over Output Voltage) 800 6.0 5.5 5.0 Iout = 0 mA Cout = 1.0 mF TA = 25C ENABLE = Vin 4.5 4.0 5.0 V 3.3 V 3.0 V 3.5 3.0 ENABLE THRESHOLD (mV) VDO, DROPOUT VOLTAGE (mV) 85 Figure 12. Output Voltage vs. Temperature (5.0 V Fixed Output, Vin = 6 V) 250 Vout, OUTPUT VOLTAGE (V) 60 TA, TEMPERATURE (C) Figure 11. Output Voltage vs. Temperature (5.0 V Fixed Output, Vin = 5.5 V) 2.80 V 2.5 2.0 1.80 V 1.5 V 1.5 1.0 0.5 0 35 1.25 V 0 1.0 2.0 3.0 4.0 5.0 750 Enable Increasing 700 Enable Decreasing 650 Vin = 5.5 V 600 -40 6.0 -15 10 35 60 85 110 125 Vin, INPUT VOLTAGE (V) TA, TEMPERATURE (C) Figure 15. Output Voltage vs. Input Voltage Figure 16. Enable Threshold vs. Temperature http://onsemi.com 7 NCP603 TYPICAL CHARACTERISTICS 4.0 3.0 2.0 ENABLE = 0 V 1.0 0 -40 -15 10 35 60 110 Iout = 150 mA Vout = 1.25 V Iout = 1.0 mA 130 122 114 106 Iout = 150 mA 98 ENABLE = 0.9 V 125 0 20 40 80 60 100 Figure 18. Ground Current (Run Mode) vs. Temperature 5.0 V 3.3 V 1.8 V 1.25 V 60 40 20 1.0 2.0 3.0 120 106 3.0 V 1.5 V 4.0 104 103 102 101 100 Vout = ADJ Vin = 1.75 V 99 98 6.0 5.0 105 0 25 50 75 100 125 150 Vin, INPUT VOLTAGE (V) Iout, OUTPUT CURRENT (mA) Figure 19. Ground Current vs. Input Voltage Figure 20. Ground Current vs. Output Current IADJ, ADJ INPUT BIAS CURRENT (nA) 0 Vout = 5.0 V 90 -40 -20 80 0 138 Figure 17. Ground Current (Sleep Mode) vs. Temperature 140 100 146 TA, TEMPERATURE (C) 2.8 V 120 85 Iout = 1.0 mA TA, TEMPERATURE (C) 160 IGND, GROUND CURRENT (mA) IGND, GROUND CURRENT (mA) 154 5.0 IGND, GROUND CURRENT (mA) IDIS, DISABLE CURRENT (mA) 6.0 400 300 200 100 0 -40 -20 0 20 40 60 80 100 TA, TEMPERATURE (C) Figure 21. ADJ Input Bias Current vs. Temperature http://onsemi.com 8 120 NCP603 700 650 Iout(max), CURRENT LIMIT (mA) ISC, OUTPUT SHORT CIRCUIT CURRENT (mA) TYPICAL CHARACTERISTICS 600 550 500 450 -40 -20 0 20 40 60 80 100 600 500 400 300 200 100 0 120 3.0 5.0 4.0 Figure 23. Current Limit vs. Input Voltage 6.0 5.0 Regload, LOAD REGULATION (mV) 3.0 2.0 1.0 Vin = (Vout + 0.5 V) to 6.0 V Iout = 1.0 mA 0 20 40 60 80 100 4.0 3.0 2.0 1.0 Iout = 1.0 mA to 150 mA 0 -40 120 -15 10 35 60 85 110 125 TA, TEMPERATURE (C) TA, TEMPERATURE (C) Figure 24. Line Regulation vs. Temperature Figure 25. Load Regulation vs. Temperature 45 80 40 70 1.25 V 60 35 5.0 V PSRR (dB) Regline, LINE REGULATION (mV) 2.0 Figure 22. Output Short Circuit Current vs. Temperature 0 -40 -20 tEN, OUTPUT TURN ON TIME (ms) 1.0 Vin, INPUT VOLTAGE (V) 4.0 30 25 3.0 V 20 15 0 TA, TEMPERATURE (C) 1.5 V 0 40 5.0 V 30 Vin = Vout + 1.0 V Vripple = 0.5 Vp-p Cout = 1.0 mF Iout = 1.0 mA to 150 mA 20 1.25 V (ADJ) 10 -40 -20 3.3 V 50 10 20 40 60 80 100 0 120 0.1 1.0 10 100 TA, TEMPERATURE (C) f, FREQUENCY (kHz) Figure 26. Output Turn On Time vs. Temperature Figure 27. Power Supply Ripple Rejection vs. Frequency http://onsemi.com 9 NCP603 TYPICAL CHARACTERISTICS OUTPUT CAPACITOR ESR (W) 10 Vout = 5.0 V Unstable Region Vout = 1.25 V 1.0 Stable Region 0.1 0.01 Cout = 1.0 mF to 10 mF TA = -40C to 125C Vin = up to 6.0 V 0 25 50 75 100 125 150 Iout, OUTPUT CURRENT (mA) Figure 28. Output Stability with Output Capacitor ESR over Output Current Vout = 1.25 V Figure 29. Load Transient Response (1.0 mF) Vout = 1.25 V Figure 30. Load Transient Response (10 mF) http://onsemi.com 10 NCP603 DEFINITIONS Load Regulation Line Regulation The change in output voltage for a change in output load current at a constant temperature. The change in output voltage for a change in input voltage. The measurement is made under conditions of low dissipation or by using pulse techniques such that the average junction temperature is not significantly affected. Dropout Voltage The input/output differential at which the regulator output no longer maintains regulation against further reductions in input voltage. Measured when the output drops 2% below its nominal. The junction temperature, load current, and minimum input supply requirements affect the dropout level. Line Transient Response Typical output voltage overshoot and undershoot response when the input voltage is excited with a given slope. Output Noise Voltage Load Transient Response This is the integrated value of the output noise over a specified frequency range. Input voltage and output load current are kept constant during the measurement. Results are expressed in mVrms or nV Hz. Typical output voltage overshoot and undershoot response when the output current is excited with a given slope between no-load and full-load conditions. Thermal Protection Internal thermal shutdown circuitry is provided to protect the integrated circuit in the event that the maximum junction temperature is exceeded. When activated at typically 175C, the regulator turns off. This feature is provided to prevent failures from accidental overheating. Ground Current Ground Current is the current that flows through the ground pin when the regulator operates without a load on its output (IGND). This consists of internal IC operation, bias, etc. It is actually the difference between the input current (measured through the LDO input pin) and the output load current. If the regulator has an input pin that reduces its internal bias and shuts off the output (enable/disable function), this term is called the standby current (ISTBY.) Maximum Package Power Dissipation The power dissipation level at which the junction temperature reaches its maximum operating value. APPLICATIONS INFORMATION output, there is no resistor divider. If the part is enabled under no-load conditions, leakage current through the pass transistor at junction temperatures above 85C can approach several microamperes, especially as junction temperature approaches 150C. If this leakage current is not directed into a load, the output voltage will rise up to a level approximately 20 mV above nominal. The NCP603 contains an overshoot clamp circuit to improve transient response during a load current step release. When output voltage exceeds the nominal by approximately 20 mV, this circuit becomes active and clamps the output from further voltage increase. Tying the ENABLE pin to Vin will ensure that the part is active whenever the supply voltage is present, thus guaranteeing that the clamp circuit is active whenever leakage current is present. When the NCP603 adjustable regulator is disabled, the overshoot clamp circuit becomes inactive and the pass transistor leakage will charge any capacitance on Vout. If no load is present, the output can charge up to within a few millivolts of Vin. In most applications, the load will present some impedance to Vout such that the output voltage will be inherently clamped at a safe level. A minimum load of 10 mA is recommended. The NCP603 series regulator is self-protected with internal thermal shutdown and internal current limit. Typical application circuits are shown in Figures 2 and 3. Input Decoupling (Cin) A ceramic or tantalum 1.0 mF capacitor is recommended and should be connected close to the NCP603 package. Higher capacitance and lower ESR will improve the overall line transient response. Output Decoupling (Cout) The NCP603 is a stable component and does not require a minimum Equivalent Series Resistance (ESR) for the output capacitor. The minimum output decoupling value is 1.0 mF and can be augmented to fulfill stringent load transient requirements. The regulator works with ceramic chip capacitors as well as tantalum devices. Larger values improve noise rejection and load regulation transient response. Figure 28 shows the stability region for a range of operating conditions and ESR values. No-Load Regulation Considerations The NCP603 adjustable regulator will operate properly under conditions where the only load current is through the resistor divider that sets the output voltage. However, in the case where the NCP603 is configured to provide a 1.250 V http://onsemi.com 11 NCP603 Noise Decoupling Thermal The NCP603 is a low noise regulator and needs no external noise reduction capacitor. Unlike other low noise regulators which require an external capacitor and have slow startup times, the NCP603 operates without a noise reduction capacitor, has a typical 15 ms start up delay and achieves a 50 mVrms overall noise level between 10 Hz and 100 kHz. As power in the NCP603 increases, it might become necessary to provide some thermal relief. The maximum power dissipation supported by the device is dependent upon board design and layout. Mounting pad configuration on the PCB, the board material, and the ambient temperature affect the rate of junction temperature rise for the part. When the NCP603 has good thermal conductivity through the PCB, the junction temperature will be relatively low with high power applications. The maximum dissipation the NCP603 can handle is given by: Enable Operation The enable pin will turn the regulator on or off. The threshold limits are covered in the electrical characteristics table in this data sheet. The turn-on/turn-off transient voltage being supplied to the enable pin should exceed a slew rate of 10 mV/ms to ensure correct operation. If the enable function is not to be used then the pin should be connected to Vin. PD(MAX) + The output voltage can be adjusted from 1 times (Figure 2) to 4 times (Figure 3) the typical 1.250 V regulation voltage via the use of resistors between the output and the ADJ input. The output voltage and resistors are chosen using Equation 1 and Equation 2. R1) PD [ VIN(IGND@IOUT) ) IOUT(VIN * VOUT) (eq. 4) or VIN(MAX) [ (eq. 1) (eq. 3) Since TJ is not recommended to exceed 125_C (TJ(MAX)), then the NCP603 can dissipate up to 465 mW when the ambient temperature (TA) is 25_C and the device is assembled on 1 oz PCB with 645 mm2 area. The power dissipated by the NCP603 can be calculated from the following equations: Output Voltage Adjust VOUT + 1.250 1 ) R1 ) (IADJ R2 TJ(MAX) * TA RqJA [Vout * (IADJ * R1)] V * 1 ^ R2 out * 1 R1 + R2 * 1.25 1.25 PD(MAX) ) (VOUT IOUT) IOUT ) IGND (eq. 5) Hints Vin and GND printed circuit board traces should be as wide as possible. When the impedance of these traces is high, there is a chance to pick up noise or cause the regulator to malfunction. Place external components, especially the output capacitor, as close as possible to the NCP603, and make traces as short as possible. (eq. 2) Input bias current IADJ is typically less than 150 nA. Choose R2 arbitrarily t minimize errors due to the bias current and to minimize noise contribution to the output voltage. Use Equation 2 to find the required value for R1. DEVICE ORDERING INFORMATION Device Marking Code Version NCP603SNADJT1G AAU ADJ NCP603SN130T1G AAF 1.3 V NCP603SN150T1G AAV 1.5 V NCP603SN180T1G AAW 1.8 V NCP603SN250T1G ACL 2.5 V NCP603SN280T1G AAX 2.8 V NCP603SN300T1G AAY 3.0 V NCP603SN330T1G AAZ 3.3 V NCP603SN350T1G AA2 3.5 V NCP603SN500T1G AA3 5.0 V Package Shipping* TSOP-5 (Pb-Free) 3000/Tape & Reel *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 12 NCP603 PACKAGE DIMENSIONS TSOP-5 CASE 483-02 ISSUE G D 5X NOTE 5 2X 0.10 T 2X 0.20 T NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. 0.20 C A B M 5 1 4 2 L 3 B S K DETAIL Z G A DIM A B C D G H J K L M S DETAIL Z J C 0.05 SEATING PLANE H T MILLIMETERS MIN MAX 3.00 BSC 1.50 BSC 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 1.25 1.55 0_ 10 _ 2.50 3.00 SOLDERING FOOTPRINT* 0.95 0.037 1.9 0.074 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 13 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP603/D