NCP603SN280T1G - ON Semiconductor

August, 2008 − Rev. 1

1Publication Order Number:

NCP603/D

NCP603

300 mA High Performance

CMOS LDO Regulator with

Enable and Enhanced ESD

Protection

The NCP603 provides 300 mA of output current at fixed voltage

options, or an adjustable output voltage from 5.0 V down to 1.250 V. It

is designed for portable battery powered applications and offers high

performance features such as low power operation, fast enable

response time, and low dropout.

The device is designed to be used with low cost ceramic capacitors

and is packaged in the TSOP−5/SOT23−5.

Features

•Output Voltage Options:

Adjustable, 1.3 V, 1.5 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 3.5 V, 5.0 V

•Adjustable Output by External Resistors from 5.0 V down to 1.250 V

•Fast Enable Turn−on Time of 15 ms

•Wide Supply Voltage Range Operating Range

•Excellent Line and Load Regulation

•Typical Noise Voltage of 50 mVrms without a Bypass Capacitor

•Enhanced ESD Protection (HBM 3.5 kV, MM 400 V)

•These are Pb−Free Devices

Typical Applications

•SMPS Post−Regulation

•Hand−held Instrumentation & Audio Players

•Noise Sensitive Circuits – VCO, RF Stages, etc.

•Camcorders and Cameras

•Portable Computing

Figure 1. Simplified Block Diagram

Driver w/

Current Limit

Thermal

Shutdown

ENABLE

VOUT

ADJ

GND

VIN

−1.25 V

Fixed Voltage Only

Adjustable Version Only

PIN CONNECTIONS

3ADJ/NC*

Vin

2GND

ENABLE 4

Vout

(Top View)

MARKING DIAGRAM

http://onsemi.com

xxx AYWG

xxx = Specific Device Code

A = Assembly Location

Y = Year

W = Work Week

G= Pb−Free Package

TSOP−5

SN SUFFIX

CASE 483

* ADJ − Adjustable Version

* NC − Fixed Voltage Version

See detailed ordering and shipping information in the

package dimensions section on page 12 of this data sheet.

ORDERING INFORMATION

(Note: Microdot may be in either location)

NCP603

http://onsemi.com

PIN FUNCTION DESCRIPTION

Pin No. Pin Name Description

1 Vin Positive Power Supply Input

2 GND Power Supply Ground; Device Substrate

3 ENABLE The Enable Input places the device into low−power standby when pulled to logic low (< 0.4 V). Connect to Vin

if the function is not used.

4 ADJ/NC Output Voltage Adjust Input (Adjustable Version), No Connection (Fixed Voltage Versions) (Note 1)

5 Vout Regulated Output Voltage

1. True no connect. Printed circuit board traces are allowable.

ABSOLUTE MAXIMUM RATINGS

Rating Symbol Value Unit

Input Voltage (Note 2) Vin −0.3 to 6.5 V

Output, Enable, Adjustable Voltage Vout, ENABLE, ADJ −0.3 to 6.5 (or Vin + 0.3)

Whichever is Lower

Maximum Junction Temperature TJ(max) 150 °C

Storage Temperature TSTG −65 to 150 °C

ESD Capability, Human Body Model (Note 3) ESDHBM 3500 V

ESD Capability, Machine Model (Note 3) ESDMM 400 V

Moisture Sensitivity Level MSL MSL1/260 −

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the

Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect

device reliability.

2. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.

3. This device series incorporates ESD protection and is tested by the following methods:

ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114)

ESD Machine Model tested per AEC−Q100−003 (EIA/JESD22−A115)

Latchup Current Maximum Rating: v150 mA per JEDEC standard: JESD78.

THERMAL CHARACTERISTICS

Rating Symbol Value Unit

Thermal Characteristics, TSOP−5 (Note 4)

Thermal Resistance, Junction−to−Air (Note 5)

RqJA 215

°C/W

4. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.

5. Value based on copper area of 645 mm2 (or 1 in2) of 1 oz copper thickness.

OPERATING RANGES (Note 6)

Rating Symbol Min Max Unit

Input Voltage (Note 7) Vin 1.75 6 V

Adjustable Output Voltage (Adjustable Version Only) Vout 1.25 5.0 V

Output Current Iout 0 300 mA

Ambient Temperature TA−40 125 °C

6. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.

7. Minimum Vin = 1.75 V or (Vout + VDO), whichever is higher.

NCP603

http://onsemi.com

ELECTRICAL CHARACTERISTICS (Vin = 1.750 V, Vout = 1.250 V, Cin = Cout =1.0 mF, for typical values TA = 25°C, for min/max

values TA = −40°C to 125°C, unless otherwise specified.) (Note 8)

Characteristic Symbol Test Conditions Min Typ Max Unit

Regulator Output (Adjustable Voltage Version)

Output Voltage Vout Iout = 1.0 mA to 150 mA

Vin = 1.75 V to 6.0 V,

Vout = ADJ

1.231

(−1.5%)

1.250 1.269

(+1.5%)

Output Voltage Vout Iout = 1.0 mA to 300 mA

Vin = 1.75 V to 6.0 V,

Vout = ADJ = 1.25 V

1.213

(−3%)

1.250 1.287

(+3%)

Power Supply Ripple Rejection (Note 9) PSRR Iout = 1.0 mA to 150 mA

Vin = Vout + 1 V + 0.5 Vp−p

f = 120 Hz

f = 1.0 kHz

f = 10 kHz

−

Line Regulation Regline Vin = 1.750 V to 6.0 V,

Iout = 1.0 mA

−1.0 10 mV

Load Regulation Regload Iout = 1.0 mA to 300 mA −2.0 45 mV

Output Noise Voltage (Note 9) Vnf = 10 Hz to 100 kHz −50 −mVrms

Output Short Circuit Current Isc 350 650 900 mA

Dropout Voltage

1.25 V

VDO Measured at: Vout – 2.0%,

Iout = 150 mA, Figure 2 −175 250

Dropout Voltage

1.25 V

VDO Measured at: Vout – 2.0%,

Iout = 300 mA, Figure 2 −375 480

Output Current Limit (Note 9) Iout(max) 300 650 −mA

Regulator Output (Fixed Voltage Version) (Vin = Vout + 0.5 V, Cin = Cout =1.0 mF, for typical values TA = 25°C, for min/max values TA =

−40°C to 125°C; unless otherwise noted.) (Note 8)

Output Voltage

1.3 V

1.5 V

1.8 V

2.5 V

2.8 V

3.0 V

3.3 V

3.5 V

5.0 V

Vout Iout = 1.0 mA to 150 mA

Vin = (Vout + 0.5 V) to 6.0 V

(−2%)

1.270

1.470

1.764

2.450

2.744

2.940

3.234

3.430

4.900

1.3

1.5

1.8

2.5

2.8

3.0

3.3

3.5

5.0

(+2%)

1.326

1.530

1.836

2.550

2.856

3.060

3.366

3.570

5.100

Output Voltage

1.3 V

1.5 V

1.8 V

2.5 V

2.8 V

3.0 V

3.3 V

3.5 V

5.0 V

Vout Iout = 1.0 mA to 300 mA

Vin = (Vout + 0.5 V) to 6.0 V

(−3%)

1.261

1.455

1.746

2.425

2.716

2.910

3.201

3.395

4.850

1.3

1.5

1.8

2.5

2.8

3.0

3.3

3.5

5.0

(+3%)

1.339

1.545

1.854

2.575

2.884

3.090

3.399

3.605

5.150

Power Supply Ripple Rejection (Note 9) PSRR Iout = 1.0 mA to 150 mA

Vin = Vout + 1 V + 0.5 Vp−p

f = 120 Hz

f = 1.0 kHz

f = 10 kHz

−

Line Regulation Regline Vin = 1.750 V to 6.0 V,

Iout = 1.0 mA

−1.0 10 mV

Load Regulation Regload Iout = 1.0 mA to 150 mA

Iout = 1.0 mA to 300 mA

−

2.0

8. Performance guaranteed over the indicated operating temperature range by design and/or characterization, production tested at TJ = TA =

25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.

9. Values based on design and/or characterization.

NCP603

http://onsemi.com

ELECTRICAL CHARACTERISTICS (Vin = 1.750 V, Vout = 1.250 V (adjustable version)), (Vin = Vout + 0.5 V (fixed version)),

Cin = Cout =1.0 mF, for typical values TA = 25°C, for min/max values TA = −40°C to 125°C, unless otherwise specified.) (Note 10)

Characteristic Symbol Test Conditions Min Typ Max Unit

Output Noise Voltage (Note 11) Vnf = 10 Hz to 100 kHz −50 −mVrms

Output Short Circuit Current Isc 350 650 900 mA

Dropout Voltage

1.3 V

1.5 V

1.8 V

2.5 V

2.7 V to 5.0 V

VDO Measured at: Vout – 2.0%

Iout = 150 mA −

−

175

150

125

250

225

175

125

Dropout Voltage

1.3 V

1.5 V

1.8 V

2.5 V

2.7 V to 5.0 V

VDO Measured at: Vout – 2.0%

Iout = 300 mA −

−

375

350

245

187

157

480

400

340

275

230

Output Current Limit (Note 11) Iout(max) 300 650 −mA

General

Disable Current IDIS ENABLE = 0 V, Vin = 6 V

−40°C ≤ TA ≤ 85°C

−0.01 1.0 mA

Ground Current IGND ENABLE = 0.9 V,

Iout = 1.0 mA to 300 mA

−145 180 mA

Thermal Shutdown Temperature (Note 11) TSD −175 −°C

Thermal Shutdown Hysteresis (Note 11) TSH −10 −°C

ADJ Input Bias Current IADJ −0.75 −0.75 mA

Chip Enable

ENABLE Input Threshold Voltage Vth(EN) V

Voltage Increasing, Logic High 0.9 − −

Voltage Decreasing, Logic Low − − 0.4

Enable Input Bias Current (Note 11) IEN −3.0 100 nA

Timing

Output Turn On Time (Note 11)

1.25 V to 3.5 V

5.0 V

tEN ENABLE = 0 V to Vin −

−

10.Performance guaranteed over the indicated operating temperature range by design and/or characterization, production tested at TJ = TA

= 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.

11. Values based on design and/or characterization.

NCP603

http://onsemi.com

Figure 2. Typical Application Circuit for Vout = 1.250 V

(Adjustable Version)

Figure 3. Typical Application Circuit for Adjustable Vout

VIN

ENABLE

VOUT

COUT

CIN

VIN

ENABLE

VOUT

COUT

CIN

Figure 4. Typical Application Circuit

(Fixed Voltage Version)

VIN VOUT

COUT

CIN

NCP603

http://onsemi.com

TYPICAL CHARACTERISTICS

Figure 5. Output Voltage vs. Temperature

(Vin = Vout + 0.5 V)

Figure 6. Output Voltage vs. Temperature

(Vin = 6.0 V)

TA, TEMPERATURE (°C) TA, TEMPERATURE (°C)

100806040200−20−40

1.240

1.244

1.248

1.252

1.256

1.260

12511085603510−15−40

1.240

1.244

1.248

1.252

1.256

1.260

Figure 7. Output Voltage vs. Temperature

(1.5 V Fixed Output, Vin = 2 V)

Figure 8. Output Voltage vs. Temperature

(1.5 V Fixed Output, Vin = 6 V)

TA, TEMPERATURE (°C) TA, TEMPERATURE (°C)

1108560−40 3510−15

1.475

1.480

1.485

1.490

1.495

1.500

12585603510−15−40

1.475

1.480

1.485

1.490

1.495

1.500

Figure 9. Output Voltage vs. Temperature

(3.0 V Fixed Output, Vin = 3.5 V)

Figure 10. Output Voltage vs. Temperature

(3.0 V Fixed Output, Vin = 6 V)

TA, TEMPERATURE (°C) TA, TEMPERATURE (°C)

12585603510−15−40

2.975

2.980

2.985

2.990

2.995

3.000

3.005

12511085603510−15−40

2.970

2.985

2.990

2.995

3.005

120

Vout, OUTPUT VOLTAGE (V)

125

Vout, OUTPUT VOLTAGE (V)

Iout = 1.0 mA

Iout = 150 mA

Vin = Vout + 0.5 V

Vout = ADJ

Iout = 1.0 mA

Iout = 150 mA

Vin = 6.0 V

Vout = ADJ

Iout = 1.0 mA

Iout = 150 mA

110

Vout, OUTPUT VOLTAGE (V)

Iout = 1.0 mA

Iout = 150 mA

110

Iout = 1.0 mA

Iout = 150 mA

3.000

2.980

Iout = 1.0 mA

Iout = 150 mA

2.975

NCP603

http://onsemi.com

TYPICAL CHARACTERISTICS

1.25 V

3.3 V

5.0 V

Figure 11. Output Voltage vs. Temperature

(5.0 V Fixed Output, Vin = 5.5 V)

Figure 12. Output Voltage vs. Temperature

(5.0 V Fixed Output, Vin = 6 V)

TA, TEMPERATURE (°C) TA, TEMPERATURE (°C)

11085603510−15−40

4.965

4.970

4.980

4.990

4.995

5.000

12511085603510−15−40

4.965

4.970

4.980

4.985

4.995

5.000

Figure 13. Dropout Voltage vs. Temperature

(Over Current Range)

Figure 14. Dropout Voltage vs. Temperature

(Over Output Voltage)

TA, TEMPERATURE (°C) TA, TEMPERATURE (°C)

100806040200−20−40

100

150

200

250

120806040200−20−40

100

150

200

250

Figure 15. Output Voltage vs. Input Voltage Figure 16. Enable Threshold vs. Temperature

Vin, INPUT VOLTAGE (V) TA, TEMPERATURE (°C)

6.05.04.03.02.01.00

0.5

1.0

2.0

2.5

4.0

5.0

6.0

12511085603510−15−40

600

650

700

750

800

125

Vout, OUTPUT VOLTAGE (V)

120

VDO, DROPOUT VOLTAGE (mV)

Iout = 1.0 mA

Iout = 150 mA

Iout = 1.0 mA

Iout = 150 mA

Iout = 1.0 mA

Iout = 150 mA

Vout = ADJ

Iout = 50 mA

100

VDO, DROPOUT VOLTAGE (mV)

Vout = 1.25 V

1.50 V

1.80 V

3.00 V

2.80 V

Vout, OUTPUT VOLTAGE (V)

Iout = 0 mA

Cout = 1.0 mF

TA = 25°C

ENABLE = Vin

ENABLE THRESHOLD (mV)

Vin = 5.5 V

Enable Increasing

Enable Decreasing

4.985

4.975

4.990

4.975

5.00 V

Iout = 150 mA

1.5

3.0

3.5

4.5

5.5

1.5 V 1.80 V

3.0 V

2.80 V

NCP603

http://onsemi.com

TYPICAL CHARACTERISTICS

1.5 V

1.8 V

Figure 17. Ground Current (Sleep Mode) vs.

Temperature

Figure 18. Ground Current (Run Mode) vs.

Temperature

TA, TEMPERATURE (°C) TA, TEMPERATURE (°C)

11085603510−15−40

1.0

2.0

3.0

5.0

6.0

1201006040200−20−40

106

114

138

154

Figure 19. Ground Current vs. Input Voltage

Vin, INPUT VOLTAGE (V)

5.04.03.02.01.00

120

160

Figure 20. Ground Current vs. Output Current

Figure 21. ADJ Input Bias Current vs.

Temperature

Iout, OUTPUT CURRENT (mA)

TA, TEMPERATURE (°C)

1501251007550250

100

101

102

104

105

106

1201008040200−20−40

200

300

400

125

IDIS, DISABLE CURRENT (mA)

IGND, GROUND CURRENT (mA)

6.0

IGND, GROUND CURRENT (mA)

ENABLE = 0 V

Iout = 1.0 mA

Iout = 150 mA

IGND, GROUND CURRENT (mA)

IADJ, ADJ INPUT BIAS CURRENT (nA)

4.0

ENABLE = 0.9 V

146

100 103

Vout = ADJ

Vin = 1.75 V

100

122

130

Iout = 1.0 mA

Iout = 150 mA

Vout = 1.25 V

Vout = 5.0 V

140 2.8 V 3.0 V

3.3 V 5.0 V

1.25 V

NCP603

http://onsemi.com

TYPICAL CHARACTERISTICS

5.0 V

3.0 V

1.5 V

1.25 V (ADJ)

Vin = Vout + 1.0 V

Vripple = 0.5 Vp−p

Cout = 1.0 mF

Iout = 1.0 mA to 150 mA

Figure 22. Output Short Circuit Current vs.

Temperature

Figure 23. Current Limit vs. Input Voltage

TA, TEMPERATURE (°C) Vin, INPUT VOLTAGE (V)

1008040200−20−40

450

500

550

600

650

6.05.03.02.01.00

100

200

300

500

700

Figure 24. Line Regulation vs. Temperature Figure 25. Load Regulation vs. Temperature

TA, TEMPERATURE (°C) TA, TEMPERATURE (°C)

10040200−20−40

2.0

4.0

125603510−15−40

1.0

2.0

3.0

4.0

5.0

Figure 26. Output Turn On Time vs.

Temperature

Figure 27. Power Supply Ripple Rejection vs.

Frequency

TA, TEMPERATURE (°C) f, FREQUENCY (kHz)

12010040200−20−40

100101.00.1

120

ISC, OUTPUT SHORT CIRCUIT CURRENT (mA)

Iout(max), CURRENT LIMIT (mA)

120

Regline, LINE REGULATION (mV)

110

Regload, LOAD REGULATION (mV)

tEN, OUTPUT TURN ON TIME (ms)

PSRR (dB)

4.0

600

1.0

3.0

Vin = (Vout + 0.5 V) to 6.0 V

Iout = 1.0 mA Iout = 1.0 mA to 150 mA

400

8060 85

60 80

5.0 V

3.3 V

1.25 V

NCP603

http://onsemi.com

TYPICAL CHARACTERISTICS

Figure 28. Output Stability with Output

Capacitor ESR over Output Current

Iout, OUTPUT CURRENT (mA)

1251007550250

0.01

0.1

1.0

150

OUTPUT CAPACITOR ESR (W)

Cout = 1.0 mF to 10 mF

TA = −40°C to 125°C

Vin = up to 6.0 V

Unstable Region

Stable Region

Vout = 5.0 V

Vout = 1.25 V

Figure 29. Load Transient Response (1.0 mF)

Figure 30. Load Transient Response (10 mF)

Vout = 1.25 V

NCP603

http://onsemi.com

DEFINITIONS

Load Regulation

The change in output voltage for a change in output load

current at a constant temperature.

Dropout Voltage

The input/output differential at which the regulator output

no longer maintains regulation against further reductions in

input voltage. Measured when the output drops 2% below its

nominal. The junction temperature, load current, and

minimum input supply requirements affect the dropout level.

Output Noise Voltage

This is the integrated value of the output noise over a

specified frequency range. Input voltage and output load

current are kept constant during the measurement. Results

are expressed in mVrms or nV √ Hz.

Ground Current

Ground Current is the current that flows through the

ground pin when the regulator operates without a load on its

output (IGND). This consists of internal IC operation, bias,

etc. It is actually the difference between the input current

(measured through the LDO input pin) and the output load

current. If the regulator has an input pin that reduces its

internal bias and shuts off the output (enable/disable

function), this term is called the standby current (ISTBY

Line Regulation

The change in output voltage for a change in input voltage.

The measurement is made under conditions of low

dissipation or by using pulse techniques such that the

average junction temperature is not significantly affected.

Line Transient Response

Typical output voltage overshoot and undershoot

response when the input voltage is excited with a given

slope.

Load Transient Response

Typical output voltage overshoot and undershoot

response when the output current is excited with a given

slope between no−load and full−load conditions.

Thermal Protection

Internal thermal shutdown circuitry is provided to protect

the integrated circuit in the event that the maximum junction

temperature is exceeded. When activated at typically 175°C,

the regulator turns off. This feature is provided to prevent

failures from accidental overheating.

Maximum Package Power Dissipation

The power dissipation level at which the junction

temperature reaches its maximum operating value.

APPLICATIONS INFORMATION

The NCP603 series regulator is self−protected with

internal thermal shutdown and internal current limit. Typical

application circuits are shown in Figures 2 and 3.

Input Decoupling (Cin)

A ceramic or tantalum 1.0 mF capacitor is recommended

and should be connected close to the NCP603 package.

Higher capacitance and lower ESR will improve the overall

line transient response.

Output Decoupling (Cout)

The NCP603 is a stable component and does not require

a minimum Equivalent Series Resistance (ESR) for the

output capacitor. The minimum output decoupling value is

1.0 mF and can be augmented to fulfill stringent load

transient requirements. The regulator works with ceramic

chip capacitors as well as tantalum devices. Larger values

improve noise rejection and load regulation transient

response. Figure 28 shows the stability region for a range of

operating conditions and ESR values.

No−Load Regulation Considerations

The NCP603 adjustable regulator will operate properly

under conditions where the only load current is through the

resistor divider that sets the output voltage. However, in the

case where the NCP603 is configured to provide a 1.250 V

output, there is no resistor divider. If the part is enabled

under no−load conditions, leakage current through the pass

transistor at junction temperatures above 85°C can approach

several microamperes, especially as junction temperature

approaches 150°C. If this leakage current is not directed into

a load, the output voltage will rise up to a level

approximately 20 mV above nominal.

The NCP603 contains an overshoot clamp circuit to

improve transient response during a load current step

release. When output voltage exceeds the nominal by

approximately 20 mV, this circuit becomes active and

clamps the output from further voltage increase. Tying the

ENABLE pin to Vin will ensure that the part is active

whenever the supply voltage is present, thus guaranteeing

that the clamp circuit is active whenever leakage current is

present.

When the NCP603 adjustable regulator is disabled, the

overshoot clamp circuit becomes inactive and the pass

transistor leakage will charge any capacitance on Vout. If no

load is present, the output can charge up to within a few

millivolts of Vin. In most applications, the load will present

some impedance to Vout such that the output voltage will be

inherently clamped at a safe level. A minimum load of

10 mA is recommended.

NCP603

http://onsemi.com

Noise Decoupling

The NCP603 is a low noise regulator and needs no

external noise reduction capacitor. Unlike other low noise

regulators which require an external capacitor and have slow

startup times, the NCP603 operates without a noise

reduction capacitor, has a typical 15 ms start up delay and

achieves a 50 mVrms overall noise level between 10 Hz and

100 kHz.

Enable Operation

The enable pin will turn the regulator on or off. The

threshold limits are covered in the electrical characteristics

table in this data sheet. The turn−on/turn−off transient

voltage being supplied to the enable pin should exceed a

slew rate of 10 mV/ms to ensure correct operation. If the

enable function is not to be used then the pin should be

connected to Vin.

Output Voltage Adjust

The output voltage can be adjusted from 1 times

(Figure 2) to 4 times (Figure 3) the typical 1.250 V

regulation voltage via the use of resistors between the output

and the ADJ input. The output voltage and resistors are

chosen using Equation 1 and Equation 2.

VOUT +1.250 ǒ1)R1

R2Ǔ)(IADJ R1) (eq. 1)

R1 +R2 * ƪ[Vout *(IADJ *R1)]

1.25 *1ƫ^R2 ƪVout

1.25 *1ƫ

(eq. 2)

Input bias current IADJ is typically less than 150 nA.

Choose R2 arbitrarily t minimize errors due to the bias

current and to minimize noise contribution to the output

voltage. Use Equation 2 to find the required value for R1.

Thermal

As power in the NCP603 increases, it might become

necessary to provide some thermal relief. The maximum

power dissipation supported by the device is dependent

upon board design and layout. Mounting pad configuration

on the PCB, the board material, and the ambient temperature

affect the rate of junction temperature rise for the part. When

the NCP603 has good thermal conductivity through the

PCB, the junction temperature will be relatively low with

high power applications. The maximum dissipation the

NCP603 can handle is given by:

PD(MAX) +TJ(MAX) *TA

RqJA (eq. 3)

Since TJ is not recommended to exceed 125_C (TJ(MAX)),

then the NCP603 can dissipate up to 465 mW when the

ambient temperature (TA) is 25_C and the device is

assembled on 1 oz PCB with 645 mm2 area.

The power dissipated by the NCP603 can be calculated

from the following equations:

PD[VIN(IGND@IOUT))IOUT(VIN *VOUT)

(eq. 4)

VIN(MAX) [PD(MAX) )(VOUT IOUT)

IOUT )IGND (eq. 5)

Hints

Vin and GND printed circuit board traces should be as

wide as possible. When the impedance of these traces is

high, there is a chance to pick up noise or cause the regulator

to malfunction. Place external components, especially the

output capacitor, as close as possible to the NCP603, and

make traces as short as possible.

DEVICE ORDERING INFORMATION

Device Marking Code Version Package Shipping*

NCP603SNADJT1G AAU ADJ

TSOP−5

(Pb−Free) 3000/Tape & Reel

NCP603SN130T1G AAF 1.3 V

NCP603SN150T1G AAV 1.5 V

NCP603SN180T1G AAW 1.8 V

NCP603SN250T1G ACL 2.5 V

NCP603SN280T1G AAX 2.8 V

NCP603SN300T1G AAY 3.0 V

NCP603SN330T1G AAZ 3.3 V

NCP603SN350T1G AA2 3.5 V

NCP603SN500T1G AA3 5.0 V

*For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting

Techniques Reference Manual, SOLDERRM/D.

NCP603

http://onsemi.com

PACKAGE DIMENSIONS

TSOP−5

CASE 483−02

ISSUE G NOTES:

1. DIMENSIONING AND TOLERANCING PER

ASME Y14.5M, 1994.

2. CONTROLLING DIMENSION: MILLIMETERS.

3. MAXIMUM LEAD THICKNESS INCLUDES

LEAD FINISH THICKNESS. MINIMUM LEAD

THICKNESS IS THE MINIMUM THICKNESS

OF BASE MATERIAL.

4. DIMENSIONS A AND B DO NOT INCLUDE

MOLD FLASH, PROTRUSIONS, OR GATE

BURRS.

5. OPTIONAL CONSTRUCTION: AN

ADDITIONAL TRIMMED LEAD IS ALLOWED

IN THIS LOCATION. TRIMMED LEAD NOT TO

EXTEND MORE THAN 0.2 FROM BODY.

DIM MIN MAX

MILLIMETERS

A3.00 BSC

B1.50 BSC

C0.90 1.10

D0.25 0.50

G0.95 BSC

H0.01 0.10

J0.10 0.26

K0.20 0.60

L1.25 1.55

M0 10

S2.50 3.00

123

54 S

0.7

0.028

1.0

0.039

ǒmm

inchesǓ

SCALE 10:1

0.95

0.037

2.4

0.094

1.9

0.074

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

0.20

CAB

T0.10

2X T0.20

NOTE 5

SEATING

PLANE

0.05

DETAIL Z

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice

to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All

operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights

nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications

intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should

Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,

and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death

associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal

Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81−3−5773−3850

NCP603/D

LITERATURE FULFILLMENT:

Literature Distribution Center for ON Semiconductor

P.O. Box 5163, Denver, Colorado 80217 USA

Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada

Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

For additional information, please contact your local

Sales Representative