NOTE: PINS NOT ELECTRICALLY CONNECTED ARE OMITTED. ELECTRICAL SPECIFICATIONS: 1.0 INDUCTANCE: (P6J6) : (P1J1) : 65 uH TYP @.01V, 10KHz 2.0 DC RESISTANCE: P6J6 : .5 OHM MAX P3J3 : .5 OHM MAX P2-J2 : .5 OHM MAX P1J1 : .5 OHM MAX 3.0 COMMON MODE : CMA (dB) FREQUENCY <MHz)> TYPICAL MIN 8 5 5 17 15 20 23 15 70 eC 20 200 22 17 300 i 6 Bel Stewart Connector MagJack 11118 Susquehanna Trail, South Glen Rock, Pa 17327-9199 717.234.7512 http://www.stewartconnector.com THIS DRAWING AND THE SUBJECT MATTER SHOWN THEREON ARE CONFIDENTIAL AND PROPERTY OF BEL STEWART ONNECTOR AND SHALL NOT BE REPRODUCED, COPIED, OR USED IN ANY MANNER WITHOUT PRIOR WRITTEN CONTENT) SHEET DRAWING NO. S]-50054 ae) 4 OF BEL STEWART CONNECTOR, THE SUBJECT MATTER MAY BE PATENTED OR A PATENT MAY BE PENDING. 1 OF 3NOTES: 1. CONNECTOR MATERIALS: CONTACT/SHIELD: COPPER ALLOY SHIELD PLATING: NICKEL OR TIN CONTACT PLATING: SELECTIVE GOLD, 50 MICRO-INCHES MIN. IN CONTACT AREA. 2. PIN NOT ELECTRICALLY CONNECTED MAYBE OMITTED. SEE ELECTRICAL DRAWING FOR OMITTED PINS. 3. TOLERANCES COMPLY WITH F.C.C. DIMENSION REQUIREMENTS. 4. ALL TOLERANCES NOT OTHERWISE SPECIFIED TO BE +.005 [0.13] 5. WAVE SOLDER COMPATIBLE PREHEAT 125C/90SECS. HOUSING: THERMOPLASTIC UL94 V-0 >< Part Number = CNTRY YYWW FC oo Bel Stewart 6 Aaah So | 8&8 + 635 [16.13] MAX .708 [17.98] REF. +z iieo Qo = io 6 Ss J 5 Ses ) ot me fe So 5, J gz | & ) Oo 8 ft | fo | | I | .083 [2.12] | i | HIGHEST POINT 040 [1.02 4.127 OF BEAM } (495 + [ ] PIN: J REF. [10.79 +.127] P.C.B. RECOMMENDED HOLE LAYOUT SEEN FROM COMPONENT SIDE TOLERANCE +.003 [0.08] UNLESS OTHERWISE SPECIFIED .050 TYP 025 [0.64] 100 [2.54] TYP _ 9.035 [0.89] (8) pee 8 3 Oa) aNe i a laf | 8 Pre TY [ bob > , 6.062 5] (2) eb 6 | PD _ _fTy_ L) | Cr) } } 128 [3.25] 3 725 [316] (2) 430 [10.92] fe 2 (POSTS) = 450 [11.43] ] & 610 [15.49] , DNNECTOR AND SHALL NOT BE REPRODUCED, COPIED, OR USED IN ANY MANNER WITHOUT PRIOR WRITTEN CONTENT THE SUBJECT MATTER MAY BE PATENTED OR A PATENT MAY BE PENDING. THIS DRAWING AND THE SUBJECT MATTER SHOWN THEREON ARE CONFIDENTIAL AND PROPERTY OF BEL STEWART OF BEL STEWART CONNECTOR, Bel Stewart Connector 11118 Susquehanna Trail, South Glen Rock, Pa 17327-9199 717.234.7512 MagJack http://www.stewartconnector.com SHEET 2 OF 3 DRAWING NO. SI50054 O5POINT OF CONTACT 656 [16.66] WITH mae tI | .080 [2.03 \ 554 [14.07] > > ce | L o00 (TOP OF PCB TO BOTTOM OF OPENING) Sa 010 MAX. RADIUS(4) - .275 [6.98] SUGGESTED PANEL OPENING MAX 1. THE SUGGESTED PANEL OPENING IS INTENDED TO GIVE THE USER THE ABILITY TO HAVE REASONABLE JACK / PANEL CLEARANCES YET MAINTAIN RELIABLE GROUNDING CAPABILITY. 2. ALL TOLERANCES NOT OTHERWISE SPECIFIED TO BE +.005 [0.13] Bel Stewart Connector MagJack 11118 Susquehanna Trail, South Glen Rock, Pa 17327-9199 THIS DRAWING AND THE SUBJECT MATTER SHOWN THEREON ARE CONFIDENTIAL AND PROPERTY OF BEL STEWART ONNECTOR AND SHALL NOT BE REPRODUCED, COPIED, OR USED IN ANY MANNER WITHOUT PRIOR WRITTEN CONTENT) SHEET DRAWING NO. SI50054 O 5 OF BEL STEWART CONNECTOR, THE SUBJECT MATTER MAY BE PATENTED OR A PATENT MAY BE PENDING. 3 OF 3 E 717.234.7512 hitp://www.stewartconnector.com