ISL6142, ISL6152 (R) Data Sheet July 2004 Negative Voltage Hot Plug Controller FN9086.1 Typical Application The ISL6142/52 are 14 pin, negative voltage hot plug controllers that allow a board to be safely inserted and removed from a live backplane. Inrush current is limited to a programmable value by controlling the gate voltage of an external N-channel pass transistor. The pass transistor is turned off if the input voltage is less than the Under-Voltage threshold, or greater than the OverVoltage threshold. The PWRGD/PWRGD outputs can be used to directly enable a power module. When the Gate and DRAIN voltages are both considered good the output is latched in the active state. GND Logic Supply GND VDD FAULT DIS PWRGD PWRGD ISOUT R10 R4 ISL6142/ISL6152 UV R5 OV R6 CT VEE IS- IS+ SENSE GATE DRAIN LOAD R9 C3 R7 R8 C1 R3 C2 R2 RL IntelliTripTM The electronic circuit breaker and programmable current limit features protect the system against short circuits. When the Over-Current threshold is exceeded, the output current is limited for a time-out period before the circuit breaker trips and shuts down the FET. The time-out period is programmable with an external capacitor connected to the CT pin. If the fault disappears before the programmed time-out, normal operation resumes. In addition, the IntelliTripTM electronic circuit breaker has a fast Hard Fault shutdown, with a threshold set at 4 times the Over-Current trip point. When activated, the GATE is immediately turned off and then slowly turned back on for a single retry. CL -48V IN R1 = 0.02 (1%) R2 = 10 (5%) R3 = 18K (5%) R4 = 549K (1%) R5 = 6.49K (1%) R1 R6 = 10K (1%) R7 = R8 = 400 (1%) R9 = 4.99K (1%) R10 = 5.1K (10%) C1 = 150nF (25V) Q1 -48V OUT C2 = 3.3nF (100V) C3 = 1500pF (25V) Q1 = IRF530 CL = 100uF (100V) RL = Equivalent load Features * Operates from -20V to -80V (-100V Absolute Max Rating) * Programmable Inrush Current * Programmable Time-Out * Programmable Current Limit The IS+, IS-, and ISOUT pins combine to provide a load current monitor feature that presents a scaled version of the load current at the ISOUT pin. Current to voltage conversion is accomplished by placing a resistor (R9) from ISOUT to the negative input (-48V). * Programmable Over-Voltage Protection Related Literature * IntelliTripTM Electronic Circuit Breaker distinguishes between severe and moderate faults - Fast shutdown for short circuit faults with a single retry (fault current > 4X current limit value). * * * * * * ISL6142/52EVAL1 Board Set, Document AN1000 ISL6140/50EVAL1 Board Set, Document AN9967 ISL6140/41EVAL1 Board Set, Document AN1020 ISL6141/51 Hot Plug Controller, Document FN9079 ISL6141/51 Hot Plug Controller, Document FN9039 ISL6116 Hot Plug Controller, Document FN4778 NOTE: See www.intersil.com/hotplug for more information. Pinout ISL6142 OR ISL6152 (14 LEAD SOIC) PWRGD/PWRGD 1 14 VDD Top View FAULT 2 13 CT * Programmable Under-Voltage Protection - 135 mV of hysteresis ~4.7V of hysteresis at the power supply * VDD Under-Voltage Lock-Out (UVLO) ~ 16.5V * FAULT pin reports the occurrence of an Over-Current Time-Out * Disable input controls GATE shutdown and resets Over-Current fault latch * Load Current Monitor Function - ISOUT provides a scaled version of the load current - A resistor from ISOUT to -VIN provides current to voltage conversion * Power Good Control Output 12 ISOUT DIS 3 OV 4 11 DRAIN UV 5 10 GATE IS- 6 9 IS+ VEE 7 8 SENSE ISL6142/52 - Output latched "good" when DRAIN and GATE voltage thresholds are met. - (PWRGD active low: ISL6142 (L version) - PWRGD active high: ISL6152 (H version) * Pb-free available Applications * * * * 1 VoIP (Voice over Internet Protocol) Servers Telecom systems at -48V Negative Power Supply Control +24V Wireless Base Station Power CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil and Design is a registered trademark of Intersil Americas Inc. IntellitripTM is a trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2002, 2004, All Rights Reserved ISL6142, ISL6152 Ordering Information PART NUMBER TEMP. RANGE (oC) PACKAGE PKG. DWG. # ISL6142CB 0 to 70 14 Lead SOIC M14.15 ISL6142CBZA (See Note) 0 to 70 14 Lead SOIC M14.15 (Pb-free) ISL6152CB 0 to 70 14 Lead SOIC M14.15 ISL6152CBZA (See Note) 0 to 70 14 Lead SOIC M14.15 (Pb-free) ISL6142IB -40 to 85 14 Lead SOIC M14.15 ISL6142IBZA (See Note) -40 to 85 14 Lead SOIC M14.15 (Pb-free) ISL6152IB -40 to 85 14 Lead SOIC M14.15 ISL6152IBZA (See Note) -40 to 85 14 Lead SOIC M14.15 (Pb-free) *Add "-T" suffix to part number for tape and reel packaging. NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which is compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J Std-020B. 2 ISL6142, ISL6152 ISL6142, ISL6152 Block Diagram GND GND VDD - 1.265V + R4 UVLO + - UV VEE REGULATOR, VEE REFERENCES - 1.255V + R5 UV 13V + VEE OV + 1.255V - + VEE - R6 210mV + OV LOGIC, TIMING, GATE DRIVE HARD FAULT + VEE GATE - 11.1V - LOGIC SUPPLY R10 50mV + CURRENT LIMIT REGULATOR (ISL6142) LATCH, LOGIC, OUTPUT DRIVE - 1.3V + PWRGD (ISL6152) + VEE FAULT FAULT - VEE 8.0V DISABLE LOGIC INPUT PWRGD + VEE + VEE DIS + + + VEE 13V VEE+5V CT - 8.5V C3 TO ADC VEE TIMER + + VEE STOP GATE CURRENT SENSE ISOUT VEE R7 IS- IS+ GATE SENSE R8 R9 R3 C1 DRAIN C2 LOAD R2 CL R1 -48V IN Q1 FIGURE 1. BLOCK DIAGRAM 3 RL -48V OUT ISL6142, ISL6152 Pin Descriptions PWRGD (ISL6142; L Version) Pin 1 - This digital output is an open-drain pull-down device and can be used to directly enable an external module. During start-up the DRAIN and GATE voltages are monitored with two separate comparators. The first comparator looks at the DRAIN pin voltage compared to the internal VPG reference (1.3V); this measures the voltage drop across the external FET and sense resistor. When the DRAIN to VEE voltage drop is less than 1.3V, the first of two conditions required for the power to be considered good are met. In addition, the GATE voltage monitored by the second comparator must be within approximately 2.5V of its normal operating voltage (13.6V). When both criteria are met the PWRGD output will transition low and be latched in the active state, enabling the external module. When this occurs the two comparators discussed above no longer control the output. However a third comparator continues to monitor the DRAIN voltage, and will drive the PWRGD output inactive if the DRAIN voltage raises more than 8V above VEE. In addition, any of the signals that shut off the GATE (OverVoltage, Under-Voltage, Under-Voltage Lock-Out, OverCurrent time-out, pulling the DIS pin high, or powering down) will reset the latch and drive the PWRGD output high to disable the module. In this case, the output pull-down device shuts off, and the pin becomes high impedance. Typically an external pull-up of some kind is used to pull the pin high (many brick regulators have a pull-up function built in). PWRGD (ISL6152; H Version) Pin 1 - This digital output is used to provide an active high signal to enable an external module. The Power Good comparators are the same as described above, but the active state of the output is reversed (reference figure 37). When power is considered good (both DRAIN and GATE are normal) the output is latched in the active high state, the DMOS device (Q3) turns on and sinks current to VEE through a 6.2K resistor. The base of Q2 is clamped to VEE to turn it off. If the external pull-up current is high enough (>1mA, for example), the voltage drop across the resistor will be large enough to produce a logic high output and enable the external module (in this example, 1mA x 6.2K = 6.2V). Note that for all H versions, although this is a digital pin functionally, the logic high level is determined by the external pull-up device, and the power supply to which it is connected; the IC will not clamp it below the VDD voltage. Therefore, if the external device does not have its own clamp, or if it would be damaged by a high voltage, an external clamp might be necessary. If the power good latch is reset (GATE turns off), the internal DMOS device (Q3) is turned off, and Q2 (NPN) turns on to clamp the output one diode drop above the DRAIN voltage to produce a logic low, indicating power is no longer good. 4 FAULT Pin 2- This digital output is an open-drain, pull-down device, referenced to VEE. It is pulled active low whenever the Over-Current latch is set. It goes to a high impedance state when the fault latch is reset by toggling the UV or DIS pins. An external pull-up resistor to a logic supply (5V or less) is required; the fault outputs of multiple IC's can be wire-OR'd together. If the pin is not used it should be left open. DIS Pin 3 - This digital input disables the FET when driven to a logic high state. It has a weak internal pull-up device to an internal 5V rail (10A), so an open pin will also act as a logic high. The input has a nominal trip point of 1.6 V while rising, and a hysteresis of 1.0V. The threshold voltage is referenced to VEE, and is compatible with CMOS logic levels. A logic low will allow the GATE to turn on (assuming the 4 other conditions described in the GATE section are also true). The DIS pin can also be used to reset the Over-Current latch when toggled high to low. If not used the pin should be tied to the negative supply rail (-VIN). OV (Over-Voltage) Pin 4 - This analog input compares the voltage on the pin to an internal voltage reference of 1.255 V (nominal). When the input goes above the reference the GATE pin is immediately pulled low to shut off the external FET. The built in 25mV hysteresis will keep the GATE off until the OV pin drops below 1.230V (the nominal high to low threshold). A typical application will use an external resistor divider from VDD to -VIN to set the OV trip level. A threeresistor divider can be used to set both OV and UV trip points to reduce component count. UV (Under-Voltage) Pin 5 - This analog input compares the voltage on the pin to an internal comparator with a built in hysteresis of 135mv. When the UV input goes below the nominal reference voltage of 1.120V, the GATE pin is immediately pulled low to shut off the external FET. The GATE will remain off until the UV pin rises above a 1.255V low to high threshold. A typical application will use an external resistor divider from VDD to -VIN to set the UV level as desired. A three-resistor divider can be used to set both OV and UV trip points to reduce component count. The UV pin is also used to reset the Over-Current latch. The pin must be cycled below 1.120V (nominal) and then above 1.255V (nominal) to clear the latch and initiate a normal start-up sequence. IS- Pin 6 - This analog pin is the negative input of the current sense circuit. A sensing resistor (R7) is connected between this pin and the VEE side of resistor R1. The ratio of R1/R7 defines the ISENSE to ISOUT current scaling factor. If current sensing is not used in the application, the IS- pin should be tied directly to the IS+ pin and the node should be left floating. ISL6142, ISL6152 VEE Pin 7 - This is the most Negative Supply Voltage, such as in a -48V system. Most of the other signals are referenced relative to this pin, even though it may be far away from what is considered a GND reference. SENSE Pin 8 - This analog input monitors the voltage drop across the external sense resistor to determine if the current flowing through it exceeds the programmed Over-Current trip point (50mV / Rsense). If the Over-Current threshold is exceeded, the circuit will regulate the current to maintain a nominal voltage drop of 50mV across the R1 sense resistor, also referred to as Rsense. If current is limited for more than the programmed time-out period the IntelliTripTM electronic circuit breaker will trip and turn off the FET. A second comparator is employed to detect and respond quickly to hard faults. The threshold of this comparator is set approximately four times higher (210mV) than the OverCurrent trip point. When the hard fault comparator threshold is exceeded the GATE is immediately (10s typical) shut off (VGATE = VEE), the timer is reset, and a single retry (soft start) is initiated. IS+ Pin 9 - This analog pin is the positive input of the current sense circuit. A sensing resistor (R8) is connected between this pin and the output side of R1, which is also connected to the SENSE pin. It should match the IS- resistor (R7) as closely as possible (1%) to minimize output current error (ISOUT). If current sensing is not used in the application, the IS+ pin should be tied directly to the IS- pin and the node should be left floating. GATE Pin 10 - This analog output drives the gate of the external FET used as a pass transistor. The GATE pin is high (FET is on) when the following conditions are met: * * * * * VDD UVLO is above its trip point (~16.5V) Voltage on the UV pin is above its trip point (1.255V) Voltage on the OV pin is below its trip point (1.255V) No Over-Current conditions are present. The Disable pin is low. If any of the 5 conditions are violated, the GATE pin will be pulled low to shut off or regulate current through the FET. The GATE is latched off only when an Over-Current event exceeds the programmed time-out period. The GATE is driven high by a weak (-50A nominal) pull-up current source, in order to slowly turn on the FET. It is driven low by a 70mA (nominal) pull-down device for three of the above shut-off conditions. A larger (350mA nominal) pulldown current shuts off the FET very quickly in the event of a hard fault where the sense pin voltage exceeds approximately 210mV. DRAIN Pin 11 - This analog input monitors the voltage of the FET drain for the Power Good function. The DRAIN input is tied to two comparators with internal reference voltages of 5 1.3v and 8.0V. At initial start-up the DRAIN to VEE voltage differential must be less than 1.3V, and the GATE voltage must be within 2.5V of its normal operating voltage (13.6V) for power to be considered good. When both conditions are met, the PWRGD/PWRGD output is latched into the active state. At this point only the 8V DRAIN comparator can control the PWRGD/PWRGD output, and will drive it inactive if the DRAIN voltage exceeds VEE by more than 8.0V. ISOUT Pin 12 - This analog pin is the output of the current sense circuit. The current flowing out of this pin (ISOUT) is proportional to the current flowing through the R1 sense resistor (ISENSE). The scaling factor, ISOUT/ISENSE is defined by the resistor ratio of R1/R7. Current to voltage conversion is accomplished by placing a resistor from this pin to -VIN. The current flowing out of the pin is supplied by the internal 13V regulator and should not exceed 600A. The output voltage will clamp at approximately 8V. If current sensing is not used in the application the pin should be left open. CT Pin 13 - This analog I/O pin is used to program the OverCurrent Time-Out period with a capacitor connected to the negative supply rail (-VIN which is equal to VEE). During normal operation, the pin is pulled down to VEE. During current limiting, the capacitor is charged with a 20A (nominal) current source. When the CT pin charges to 8.5V, it times out and the GATE is latched off. If the short circuit goes away prior to the time-out, the GATE will remain on. If no capacitor is connected, the time-out will be much quicker, with only the package pin capacitance (~ 5 to 10 pF) to charge. If no external capacitor is connected to the CT pin the time-out will occur in a few sec. To set the desired timeout period use: dt = (C * dV) / I = (C * 8.5) / 20 A = 0.425*106 * C NOTE: The printed circuit board's parasitic capacitance (CT pin to the negative input, -VIN) should be taken into consideration when calculating the value of C3 needed for the desired time-out. VDD Pin 14 - This is the most positive Power Supply pin. It can range from the Under-Voltage lockout threshold (16.5V) to +80V (Relative to VEE). The pin can tolerate up to 100V without damage to the IC. ISL6142, ISL6152 . Absolute Maximum Ratings Thermal Information Supply Voltage (VDD to VEE). . . . . . . . . . . . . . . . . . . . -0.3V to 100V DRAIN, PWRGD, PWRGD Voltage . . . . . . . . . . . . . . . -0.3V to 100V UV, OV Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 60V SENSE, GATE Voltage . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 20V FAULT, DIS, IS+, IS-, ISOUT, CT . . . . . . . . . . . . . . . . . -0.3V to 8.0V ESD Rating Human Body Model (Per MIL-STD-883 Method 3015.7) . . .2000V Thermal Resistance (Typical, Note 1) JA (oC/W) 14 Lead SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Maximum Junction Temperature (Plastic Package) . . . . . . . .150oC Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC Operating Conditions Temperature Range (Industrial) . . . . . . . . . . . . . . . . . -40oC to 85oC Temperature Range (Commercial). . . . . . . . . . . . . . . . . 0oC to 70oC Supply Voltage Range (Typical) . . . . . . . . . . . . . . . . . . . 36V to 72V CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 2. PWRGD is referenced to DRAIN; VPWRGD-VDRAIN = 0V. Electrical Specifications VDD = +48V, VEE = +0V Unless Otherwise Specified. All tests are over the full temperature range; either Commercial (0oC to 70oC) or Industrial (-40oC to 85oC). Typical specs are at 25oC. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS 20 - 80 V 2.6 4.0 mA DC PARAMETRIC VDD PIN Supply Operating Range VDD Supply Current IDD UV = 3V; OV = VEE; SENSE = VEE; VDD = 80V UVLO High VUVLOH VDD Low to High transition 15 16.7 19 V UVLO Low VUVLOL VDD High to Low transition 13 15.0 17 V UVLO hysteresis 1.9 V GATE PIN A GATE Pin Pull-Up Current IPU GATE Drive on, VGATE = VEE GATE Pin Pull-Down Current IPD1 GATE Drive off, UV or OV false 70 mA GATE Pin Pull-Down Current IPD2 GATE Drive off, Over-Current Time-Out 70 mA GATE Pin Pull-Down Current IPD3 GATE Drive off; Hard Fault, Vsense > 210mv 350 mA External Gate Drive (at 20V, at 80V) GATE High Threshold (PWRGD/PWRGD active) VGATE (VGATE - VEE), 20V <=VDD <=80V VGH VGATE - VGATE VCL VCL = (VSENSE - VEE) -30 12 -50 13.6 -60 15 2.5 V V SENSE PIN Current Limit Trip Voltage Hard Fault Trip Voltage HFTV SENSE Pin Current ISENSE 40 HFTV = (VSENSE - VEE) VSENSE = 50mV 50 60 210 mV mV - 0 -0.5 A UV PIN UV Pin High Threshold Voltage VUVH UV Low to High Transition 1.240 1.255 1.270 V UV Pin Low Threshold Voltage VUVL UV High to Low Transition 1.105 1.120 1.145 V UV Pin Hysteresis VUVHY 6 135 mV ISL6142, ISL6152 Electrical Specifications VDD = +48V, VEE = +0V Unless Otherwise Specified. All tests are over the full temperature range; either Commercial (0oC to 70oC) or Industrial (-40oC to 85oC). Typical specs are at 25oC. (Continued) PARAMETER SYMBOL UV Pin Input Current TEST CONDITIONS MIN TYP MAX UNITS - -0.05 -0.5 A IINUV VUV = VEE OV Pin High Threshold Voltage VOVH OV Low to High Transition 1.235 1.255 1.275 V OV Pin Low Threshold Voltage VOVL OV High to Low Transition 1.215 1.230 1.255 V OV pin OV Pin Hysteresis VOVHY OV Pin Input Current 25 mV - -0.05 -0.5 A VDRAIN - VEE 0.80 1.30 2.00 V VDRAIN = 48V 10 38 60 A VDH VDRAIN - VEE > 8.0V 7.0 8.0V 9.0 V VOL1 VOL5 (VDRAIN - VEE) < VPG; IOUT = 1mA - 0.3 0.8 V (VDRAIN - VEE) < VPG; IOUT = 5mA - 1.50 3.0 V IOH VDRAIN = 48V, V PWRGD = 80V - 0.05 10 A VOL VDRAIN = 5V, IOUT = 1mA - 0.80 1.0 V IINOV VOV = VEE VPG IDRAIN DRAIN Pin Power Good Threshold (Enable PWRGD/PWRGD Output) Drain Input Bias Current DRAIN Pin Comparator Trip Point (PWRGD/PWRGD Inactive) ISL6142 (PWRGD Pin: L Version) PWRGD Output Low Voltage Output Leakage ISL6152 (PWRGD Pin: H Version) PWRGD Output Low Voltage (PWRGD-DRAIN) PWRGD Output Impedance ROUT (VDRAIN - VEE) < VPG 4.5 6.2 7.5 k DIS Pin High Threshold Voltage VDISH DIS Low to High Transition 1.60 2.20 3.00 V DIS Pin Low Threshold Voltage VDISL DIS High to Low Transition 1.1 1.50 V DIS PIN DIS Pin Hysteresis VDISHY DIS Hysteresis 1.0 DIS Pin Input High Leakage IDISINH Input Voltage = 5V 0.1 DIS Pin Input Low Current IDISINL Input Voltage = 0V 10 A FAULT Output Voltage VFVOL I = 1.6 mA 0.4 V FAULT Output Leakage IFIOH V = 5.0V ICTINL VCT = 0V V 1.0 A FAULT PIN 10 A CT PIN CT Pin Charging Current CT Pin Input Threshold VCT A 20 7.5 8.5 9.5 V IS PINS (IS-, IS+, ISOUT) ISOUT Error VSENSE = 50mV, R7 = 400, R8 = 404 2.0 % ISOUT Error VSENSE = 200mV, R7 = 400, R8 = 404 1.0 % ISOUT Offset Current VSENSE = 0.0mV, R7 = 400, R8 = 404 4.5 A Output Voltage Range (ISOUT Pin) 7 0 5 8 V ISL6142, ISL6152 Electrical Specifications VDD = +48V, VEE = +0V Unless Otherwise Specified. All tests are over the full temperature range; either Commercial (0oC to 70oC) or Industrial (-40oC to 85oC). Typical specs are at 25oC. (Continued) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS AC TIMING OV High to GATE Low tPHLOV Figures 2A, 3A 0.6 1.6 3.0 s OV Low to GATE High tPLHOV Figures 2A, 3A 1.0 7.8 12.0 s UV Low to GATE Low tPHLUV Figures 2A, 3B 0.6 1.3 3.0 s UV High to GATE High tPLHUV Figures 2A, 3B 1.0 8.4 12.0 s DIS Low to GATE Low tPHLDIS Figure 2A, 7 0.6 s DIS High to GATE High tPLHDIS Figure 2A, 7 2.5 s GATE Low (Over-Current) to FAULT Low tPHLGF Figure 2A, 8 0.5 s ISOUT Rise Time tR Figure 2A, 12 1.2 s ISOUT Fall Time tF Figure 2A, 12 4.0 s SENSE High to GATE Low tPHLSENSE Figures 2A, 9 1 3 s Current Limit to GATE Low tPHLCB Figures 2B, 11, Effective Capacitance During Test = 2550pF 1200 s Hard Fault to GATE Low (200mV comparator) Typical GATE shutdown based on application ckt. Guaranteed by design. tPHLHF Figures 10, 20, 33 10.0 s DRAIN Low to PWRGD Low (Active) tPHLDL Figures 2A, 4A DRAIN High to PWRGD High (Inactive) tPLHDH Figure 2A, 6A 0.2 s GATE High to PWRGD Low (Active) tPHLGH Figures 2A, 5A 1.0 s DRAIN Low to (PWRGD-DRAIN) High (Active) tPLHDL Figures 2A, 4B DRAIN High to (PWRGD -DRAIN) Low (Inactive) tPHLDH Figure 2A, 6B 0.5 s GATE High to (PWRGD-DRAIN) High (Active) tPLHGH Figures 2A, 5B 0.4 s ISL6142 (L Version) 0.1 3.1 5.0 s ISL6152 (H Version) 8 0.1 0.2 5.0 s ISL6142, ISL6152 ? Test Circuit and Timing Diagrams 5K 5V 48V + - 5K PWRGD FAULT VDIS 1 14 2 13 3 VOV OV VUV UV 400 VEE . 5K 11 5 10 GATE 404 9 8 7 DRAIN 1 14 2 13 3 OV VUV 4 6 FAULT VOV 4.99K 12 ISL6142 PWRGD VDD 48V + - 5K 5V UV VDRAIN VEE ISL6142 VDD CT 12 DRAIN 4 11 5 10 GATE 6 9 7 8 VDRAIN 9.0K SENSE 0.90K SENSE 0.1K VSENSE FIGURE 2B. TEST CIRCUIT FOR TIMEOUT FIGURE 2A. TYPICAL TEST CIRCUIT 2V 2V 1.255V 0V tPLHOV tPLHUV tPHLUV 13.6V 1V 1.255V UV Pin 0V tPHLOV 13.6V GATE 0V 1.125V 1.230V 1V 1V 0V 1V GATE FIGURE 3B. UV TO GATE TIMING FIGURE 3A. OV TO GATE TIMING FIGURE 3. OV AND UV TO GATE TIMING DRAIN DRAIN 1.3V 1.3V VPG tPHLDL PWRGD VPG VEE tPLHDL 1.0V 1.0V PWRGD FIGURE 4A. DRAIN TO PWRGD ACTIVE TIMING (ISL6142) FIGURE 4B. DRAIN TO PWRGD ACTIVE TIMING (ISL6152) FIGURE 4. DRAIN TO PWRGD/PWRGD TIMING VGATE - VGATE = 0V 13.6V 2.5V VGATE - VGATE = 0V 2.5V VGH GATE GATE 13.6V VGH tPLHGH tPHLGH PWRGD 1.0V FIGURE 5A. GATE TO PWRGD ACTIVE (ISL6142) 9 PWRGD 1.0V VPWRGD - VDRAIN = 0V FIGURE 5B. GATE TO PWRGD ACTIVE (ISL6152) ISL6142, ISL6152 Test Circuit and Timing Diagrams (Continued) VDRAIN - VEE = 8.0V VDRAIN - VEE = 8.0V VDH 8.0V VDH VEE - VDRAIN = 0V VEE - VDRAIN = 0V tPLHDH DRAIN 8.0V DRAIN tPHLDH PWRGD 1.0V 1.0V PWRGD VPWRGD - VDRAIN = 0V FIGURE 6A. DRAIN HIGH TO PWRGD (INACTIVE) HIGH (ISL6142) FIGURE 6B. DRAIN HIGH TO PWRGD (INACTIVE) LOW (ISL6152) FIGURE 6. DRAIN TO PWRGD/PWRGD INACTIVE TIMING VGATE - VGATE = 0V 3V DIS 1.50V GATE 0V 2.2V tPHLDIS tPLHDIS 13.6V 1.4V GATE tPHLF FAULT 1V 1V 1.0V 0V FIGURE 7. DISABLE TO GATE TIMING (ISL6142/52) FIGURE 8. FAULT TO GATE TIMING (ISL6142/52) 50mV 210mV SENSE 0V 13.6V tPHLSENSE 0V 13.6V GATE SENSE tPHLHF GATE VEE ~4V (depends on FET threshold) FIGURE 9. SENSE TO GATE (CURRENT LIMIT) TIMING FIGURE 10. SENSE TO GATE (HARD FAULT) TIMING VSENSE UV tR tPHLCB 90% GATE 1.0V 1.0V VOUT 10% tF 90% 10% Over-Current Time-Out FIGURE 11. CURRENT LIMIT TO GATE TIMING 10 FIGURE 12. OUTPUT CURRENT RISE AND FALL TIME ISL6142, ISL6152 16 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 14 Gate Voltage (V) IDD (mA) Typical Performance Curves 12 10 8 6 4 2 0 10 20 30 40 50 60 70 80 90 100 10 20 Supply Voltage (VDD) 40 60 70 80 100 FIGURE 14. GATE VOLTAGE VS SUPPLY VOLTAGE (25oC) 14 2.75 2.7 2.65 2.6 2.55 2.5 2.45 2.4 2.35 2.3 2.25 Gate Voltage (V) 13.9 13.8 13.7 13.6 13.5 13.4 13.3 -40 -20 0 20 40 60 80 100 -40 -20 0 Temperature (C) Gate Current (uA) 13.9 VDD = 80V 13.7 VDD = 20V 13.6 13.5 13.4 -40 -20 0 20 40 60 80 Temperature (C) FIGURE 17. GATE VOLTAGE VS TEMPERATURE 11 40 60 80 100 FIGURE 16. GATE VOLTAGE VS TEMPERATURE VDD = 48V 14 13.8 20 Temperature (C) FIGURE 15. SUPPLY CURRENT VS TEMPERATURE, VDD = 80V Gate Voltage (V) 50 Supply Voltage (VDD) FIGURE 13. SUPPLY CURRENT VS. SUPPLY VOLTAGE (25oC) IDD (mA) 30 100 50 49 48 47 46 45 44 43 42 41 -40 -20 0 20 40 60 80 Temperature (C) FIGURE 18. GATE PULL-UP CURRENT VS TEMPERATURE 100 90 80 70 60 50 40 30 20 10 0 -40 -20 0 20 40 60 80 100 Gate Pull Down Current (mA) Gate Pull Down Current (mA) ISL6142, ISL6152 450 400 350 300 250 200 150 100 50 0 -40 -20 0 Temperature (C) 1.6 Output Low Voltage (V) Trip Voltage (mv) 52 50 48 46 44 42 40 0 20 40 80 100 60 80 5mA 1.4 1.2 1 0.8 0.6 0.4 1mA 0.2 0 -40 100 -20 0 20 40 60 80 100 Temperature (C) Temperature (C) FIGURE 21. OVER-CURRENT TRIP VOLTAGE VS TEMPERATURE FIGURE 22. PWRGD (ISL6142) VOL VS TEMPERATURE 2 (1 ma) 6.8 Impedance (KOhms) Trip Voltage (V) 60 FIGURE 20. HARD FAULT GATE PULL-DOWN CURRENT VS TEMPERATURE 54 -20 40 Temperature (C) FIGURE 19. GATE PULL-DOWN CURRENT (UV/OV/TIME-OUT) VS TEMPERATURE -40 20 1.5 1 0.5 0 6.7 6.6 6.5 6.4 6.3 6.2 6.1 -40 -20 0 20 40 60 80 100 Temperature (C) FIGURE 23. DRAIN to PWRGD / PWRGD TRIP VOLTAGE (VPG) VS TEMPERATURE 12 -40 -20 0 20 40 60 80 Temperature (C) FIGURE 24. PWRGD (ISL6152) OUTPUT IMPEDANCE VS TEMPERATURE 100 ISL6142, ISL6152 2.5 o -40 C 5 4 3 o 85 C 2 o -40 C ISOUT Error (%) ISOUT Error (uA) 6 1 0 2 1.5 1 o 85 C 0.5 0 50 100 150 0 200 50 FIGURE 25. ISOUT ERROR VS SENSE PIN VOLTAGE FIGURE 26. ISOUT ERROR VS SENSE PIN VOLTAGE VSENSE = 0V 20.5 CT Charging Current (uA) ISOUT Offset Current (uA) 150 SENSE pin Voltage (mV) SENSE Pin Voltage (mV) 4.475 100 4.47 4.465 4.46 4.455 4.45 4.445 4.44 4.435 20 19.5 19 18.5 18 17.5 17 -40 -20 0 20 40 60 80 100 Temperature (C) FIGURE 27. ISOUT OFFSET CURRENT VS TEMPERATURE 13 -40 -20 0 20 40 60 80 100 Temperature (C) FIGURE 28. CT CHARGING CURRENT VS TEMPERATURE ISL6142, ISL6152 Applications Information GND GND VDD FAULT PWRGD DIS ISOUT Logic Supply R4 ISL6142 UV R10 R5 OV R6 CT VEE IS- IS+ SENSE GATE DRAIN ADC Q2 R9 C3 C1 R7 R8 -48V IN R1 R2 R3 C2 CL RL Q1 -48V OUT FIGURE 29. TYPICAL APPLICATION WITH MINIMUM COMPONENTS Typical Values for a representative system; which assumes: Quick Guide to Choosing Component Values 43V to 71V supply range; 48 nominal; UV = 43V; OV = 71V (See fig 29 for reference) 1A of typical current draw; 2.5 Amp Over-Current This section will describe the minimum components needed for a typical application, and will show how to select component values. Note that "typical" values may only be good for this application; the user may have to select alternate component values to optimize performance for other applications. Each block will then have more detailed explanation of how the device works, and alternatives. 100F of load capacitance (CL); equivalent RL of 48 (R = V/I = 48V/1A) R1: 0.02 (1%) R2: 10 (5%) R3: 18k (5%) R4, R5, R6 - together set the Under-Voltage (UV) and OverVoltage (OV) trip points. When the power supply ramps up and down, these trip points (and their hysteresis) will determine when the GATE is allowed to turn on and off (UV and OV do not control the PWRGD / PWRGD output). The input power supply is divided down such that when the voltage on the OV pin is below its threshold and the UV pin is above its threshold their comparator outputs will be in the proper state signaling the supply is within its desired operating range, allowing the GATE to turn on. The equations below define the comparator thresholds for an increasing (in magnitude) supply voltage. R4: 549k (1%) R5: 6.49k (1%) R6: 10k (1%) R7/R8: 400 (1%) R9: 4.99K (1%) R10: 5.10K (10%) C1: 150nF (25V) C2: 3.3nF (100V) C3: 1500pF (25V) Q1: IRF530 (100V, 17A, 0.11) Q2: N-Channel logic FET 14 R 4 + R 5 + R 6 V UV = ----------------------------------------- x 1.255 ( R5 + R6 ) (EQ. 1) R 4 + R 5 + R 6 V OV = ----------------------------------------- x 1.255 ( R6 ) (EQ. 2) ISL6142, ISL6152 The values of R4 = 549K, R5 = 6.49K, and R6 = 10K shown in figure 29 set the Under-Voltage threshold at 43V, and the Over-Voltage, turn off threshold to 71V. The Under-Voltage (UV) comparator has a hysteresis of 135mv's (4.6V of hysteresis on the supply) which correlates to a 38.4V turn off voltage. The Over-Voltage comparator has a 25mv hysteresis (1.4V of hysteresis on the supply) which translates to a turn on voltage (supply decreasing) of approximately 69.6V. Q1 - is the FET that connects the input supply voltage to the output load, when properly enabled. It needs to be selected based on several criteria: R1 resistor, and the VEE and SENSE pins should be direct and as short as possible with zero current in the sense lines. Note that in figure 30 the traces from each side of the R1 resistor also connect to the R8 (IS+), and R7 (IS-) current sensing resistors. CORRECT INCORRECT To VEE and R7 * Maximum voltage expected on the input supply (including transients) as well as transients on the output side. * Maximum current and power dissipation expected during normal operation, usually at a level just below the current limit threshold. * Power dissipation and/or safe-operating-area considerations during current limiting and single retry events. * Other considerations include the GATE voltage threshold which affects the rDS(ON) (which in turn, affects the voltage drop across the FET during normal operation), and the maximum gate voltage allowed (the IC's GATE output is clamped to ~14V). R1 - is the Over-Current sense resistor also referred to as RSENSE. If the input current is high enough, such that the voltage drop across R1 exceeds the SENSE comparator trip point (50mV nominal), the GATE pin will be pulled lower (to ~4V) and current will be regulated to 50mV/Rsense for the programmed time-out period which is set by C3. The OverCurrent threshold is defined in Equation 3 below. If the timeout period is exceeded the Over-Current latch will be set and the FET will be turned off to protect the load from excessive current. A typical value for R1 is 0.02, which sets an OverCurrent trip point of; IOC = V/R = 0.05/0.02 = 2.5 Amps. To select the appropriate value for R1, the user must first determine at what level of current it should trip, take into account worst case variations for the trip point (50mV 10mV = 20%), and the tolerances of the resistor (typically 1% or 5%). Note that the Over-Current threshold should be set above the inrush current level plus the expected load current to avoid activating the current limit and time-out circuitry during start-up. If the power good output (PWRGD/PWRGD) is used to enable an external module, the desired inrush current only needs to be considered. One rule of thumb is to set the Over-Current threshold 2-3 times higher than the normal operating current. 50mv I OC = -------------------R sense (EQ. 3) To SENSE and R8 CURRENT SENSE RESISTOR FIGURE 30. SENSE RESISTOR LAYOUT GUIDELINES CL - is the sum of all load capacitances, including the load's input capacitance itself. Its value is usually determined by the needs of the load circuitry, and not the hot plug (although there can be interaction). For example, if the load is a regulator, then the capacitance may be chosen based on the input requirements of that circuit (holding regulation under current spikes or loading, filtering noise, etc.) The value chosen will affect the peak inrush current. Note that in the case of a regulator, there may be capacitors on the output of that circuit as well; these need to be added into the capacitance calculation during inrush (unless the regulator is delayed from operation by the PWRGD/PWRGD signal). RL - is the equivalent resistive value of the load and determines the normal operating current delivered through the FET. It also affects some dynamic conditions (such as the discharge time of the load capacitors during a powerdown). A typical value might be 48 (I=V/R = 48/48 = 1A). R2, C1, R3, C2 - are related to the GATE driver, as it controls the inrush current. R2 prevents high frequency oscillations; 10 is a typical value. R2 = 10. R3 and C2 act as a feedback network to control the inrush current as shown in equation 4, where CL is the load capacitance (including module input capacitance), and IPU is the GATE pin charging current, nominally 50A. CL I inrush = I PU x ------C (EQ. 4) 2 The physical layout of the R1 sense resistor is critical to avoid the possibility of false over current events. Since it is in the main input-to-output path, the traces should be wide enough to support both the normal current, and currents up to the over-current trip point. The trace routing between the 15 Begin by choosing a value of acceptable inrush current for the system, and then solve for C2. ISL6142, ISL6152 C1 and R3 prevent Q1 from turning on momentarily when power is first applied. Without them, C2 would pull the gate of Q1 up to a voltage roughly equal to VEE*C2/Cgs(Q1) (where Cgs is the FET gate-source capacitance) before the ISL6142/52 could power up and actively pull the gate low. Place C1 in parallel with the gate capacitance of Q1; isolate them from C2 by R3. C1 =[(Vinmax - Vth)/Vth] * (C2+Cgd) - where Vth is the FET's minimum gate threshold, Vinmax is the maximum operating input voltage, and Cgd is the FET gate-drain capacitance. R3 - its value is not critical, a typical value of 18k is recommended but values down to 1K can be used. Lower values of R3 will add delay to gate turn-on for hot insertion and the single retry event following a hard fault. R7/R8/R9 - are used to sense the load current (R7/R8) and convert the scaled output current (ISOUT) to a voltage (R9) that would typically be the input signal to an A to D converter. R7 is connected between -IS and the R1 sense resistor. These two resistors set the ISENSE (current through the Rsense resistor) to ISOUT scaling factor based on equation 5 below. R8 does not effect the scaling factor but should match R7 to minimize ISOUT error. Their tolerance should be +/-1%, which will typically result in an output current error of less than 5% for a full scale condition. The trace layout is also critical to obtain optimum performance. The traces connecting these resistors to the device pins (IS+ and IS-) and to the R1 sense resistor should be kept as short as possible, match in length, and be isolated from the main current flow as illustrated in figure 30. R9 is used to convert the ISOUT current to voltage and is connected between the ISOUT pin and -VIN. The current flowing through the resistor (EQ. 5) should not exceed 600A and the voltage on the CT pin will clamp at approximately 8V. R SENSE IS OUT = I SENSE x ----------------------R7 (EQ. 5) To select the appropriate resistor values for the application the user must first define the R1 sense resistor value and the maximum load current to be detected/measured. The value of R7 should then be selected such that the maximum ISOUT current is in the 400-500A range. For example, if the user wanted to detect and measure fault currents up to the hard fault comparator trip point (10A); the maximum ISOUT current using the application components in figure 23 would be [10A x (.02/400] = 500A. The value of R9 should be set to accommodate the dynamic range of the A to D converter. For this example, a 5K resistor would produce a full scale input voltage to the converter of 2.5V (500A x 5K). Figures 32 and 33 illustrate the typical output voltage 16 response of the current sense circuit for the Over-Current Time-out and hard fault single retry events. R10 - is a pull-up resistor for the open drain FAULT output pin which goes active low when the Over-Current latch is set (Over-Current Time-Out). The output signal is referenced to VEE and the resistor is connected to a positive voltage, 5V or less, with respect to VEE. A typical value of 5K is recommended. A fault indicator LED can be placed in series with the pull-up resistor if desired. The resistor value should be selected such that it will allow enough current to drive the LED adequately (brightness). C3 - is the capacitor used to program the current limit timeout period. When the Over-Current threshold is exceeded a 20A (nominal) current source will charge the C3 capacitor from VEE to approximately 8.5V. When the voltage on the CT pin exceeds the 8.5V threshold, the GATE pin will immediately be pulled low with a 70ma pull down device, the Over-Current latch will be set, and the FET will be turned off. If the Over-Current condition goes away before the time-out period expires, the CT pin will be pulled back down to VEE, and normal operation will resume. Note that any parasitic capacitance from the CT pin to -VIN will effectively add to C3. This additional capacitance should be taken into account when calculating the C3 value needed for the desired timeout period. The value of C3 can be calculated using equation 6 where dt is the time-out period, dv is the CT pin threshold, and ICT is the capacitor charging current. -6 timeout dt C3 = ------ x I CT = ---------------------- x 20 x10 8.5V dv (EQ. 6 Q2- is an N-channel logic FET used to drive the disable pin (DIS). The DIS pin is used to enable/disable the external pass transistor (Q1) by turning the GATE drive voltage on or off. The DIS pin can also be used to reset the Over-Current latch by toggling the pin high and then low. When Q2 is off, the DIS pin is pulled high with an internal 500K resistor, connected to an internal +5V (VEE + 5V) supply rail (10A). In this condition the GATE pin is low, and Q1 is turned off. When Q2 is on, the DIS pin is pulled low to VEE allowing the GATE pin to pull up and turn on Q1. The gate of Q2 will typically be driven low (<1.5V) or High (>3.0V) with external logic circuitry referenced to the negative input (-VIN). Low-side Application Although this IC was designed for -48V systems, it can also be used as a low-side switch for positive 48V systems; the operation and components are usually similar. One possible difference is the kind of level shifting that may be needed to interface logic signals to the IC. For example, many of the IC functions are referenced to the IC substrate, connected to the VEE pin, but this pin may be considered -48V or GND, depending upon the polarity of the system. Also, the input or output logic (running at 5V or 3.3V or even lower) might be ISL6142, ISL6152 After the contact bounce subsides the UVLO and UV criteria are quickly met and the GATE begins to ramp up. As the GATE reaches approximately 4V with respect to the source, the FET begins to turn on allowing current to charge the 100F load capacitor. As the drain to source voltage begins to drop, the feedback network of C2 and R3 hold the GATE constant, in this case limiting the current to approximately 1.5A. When the DRAIN voltage completes its ramp down, the load current remains constant at approximately 1.0A as the GATE voltage increases to its final value. excessive supply or fault currents. The IntelliTripTM electronic circuit breaker is capable of detecting both hard faults, and less severe Over-Current conditions. The Over-Current trip point is determined by R1 (EQ. 3) also referred to as Rsense. When the voltage across this resistor exceeds 50mV, the current limit regulator will turn on, and the GATE will be pulled lower (to ~4V) to regulate current through the FET at 50mV/Rsense. If the fault persists and current limiting exceeds the programmed time-out period, the FET will be turned off by discharging the GATE pin to VEE. This will set the Over-Current latch and the PWRGD/PWRGD output will transition to the inactive state, indicating power is no longer good. To clear the latch and initiate a normal start-up sequence, the user must either power down the system (below the UVLO voltage), toggle the UV pin below and above its threshold (usually with an external transistor), or toggle the DIS pin high to low. Figure 32 shows the Over-Current shut down and current limiting response for a 10 short to ground on the output. Prior to the short circuit the output load is 110 producing an operating current of about 0.44A (48V/110). A 10 short is then applied to the output causing an initial fault current of 4.8A. This produces a voltage drop across the 0.02 sense resistor of approximately 95mV, roughly two times the Over-Current threshold of 50mV. The GATE is quickly pulled low to limit the current to 2.5A (50mV/Rsense) and the timer is enabled. The fault condition persists for the duration of the programmed time-out period (C3 = 1500pF) and the GATE is latched off in about 740s. There is a short filter (3s nominal) on the comparator, so current transients shorter than this will be ignored. Longer transients will initiate the GATE pull down, current limiting, and the timer. If the fault current goes away before the time-out period expires the device will exit the current limiting mode and resume normal operation. FIGURE 31. HOT INSERTION INRUSH CURRENT LIMITING, DISABLE PIN TIED TO VEE FIGURE 32. CURRENT LIMITING AND TIME-OUT externally referenced to either VDD or VEE of the IC, instead of GND. Inrush Current Control The primary function of the ISL6142/52 hot plug controller is to control the inrush current. When a board is plugged into a live backplane, the input capacitors of the board's power supply circuit can produce large current transients as they charge up. This can cause glitches on the system power supply (which can affect other boards!), as well as possibly cause some permanent damage to the power supply. The key to allowing boards to be inserted into a live backplane is to turn on the power to the board in a controlled manner, usually by limiting the current allowed to flow through a FET switch, until the input capacitors are fully charged. At that point, the FET is fully on, for the smallest voltage drop across it. Figure 31 illustrates the typical inrush current response for a hot insertion under the following conditions: VIN = -48V, Rsense = 0.02W Current limit = 50mV / 0.02 = 2.5A C1 = 150nF, C2 = 3.3nF, R3 = 18k CL = 100F, RL = 50, I LOAD = 48V / 50 ~1.0A Iinrush = 50A (100F / 3.3nF) = 1.5A Electronic Circuit Breaker/Current Limit The ISL6142/52 allows the user to program both the current limit and the time-out period to protect the system against 17 In addition to current limiting and programmable time-out, there is a hard fault comparator to respond to short circuits with an immediate GATE shutdown (typically 10s) and a single retry. The trip point of this comparator is set ~4 times ISL6142, ISL6152 (210mV) higher than the Over-Current threshold of 50mV. If the hard fault comparator trip point is exceeded, a hard pull down current (350mA) is enabled to quickly pull down the GATE and momentarily turn off the FET. The fast shutdown resets the timer and is followed by a soft start, single retry event. If the fault is still present after the GATE is slowly turned on, the current limit regulator will trip (sense pin voltage > 50mV), turn on the timer, and limit the current to 50mV/Rsense. If the fault remains and the time-out period is exceeded the GATE pin will be latched low. Note: Since the timer starts when the SENSE pin exceeds the 50mV threshold, then depending on the speed of the current transient exceeding 200mV; it's possible that the current limit time-out and shutdown can occur before the hard fault comparator trips (and thus no retry). Figure 33 illustrates the hard fault response with a zero ohm short circuit at the output. within its expected operating range and the GATE will be allowed to turn on, or remain on. If the UV pin voltage drops below its high to low threshold, or the OV pin voltage increases above its low to high threshold, the GATE pin will be pulled low, turning off the FET until the supply is back within tolerance. The OV and UV inputs are high impedance, so the value of the external resistor divider is not critical with respect to input current. Therefore, the next consideration is total current; the resistors will always draw current, equal to the supply voltage divided by the total resistance of the divider (R4+R5+R6) so the values should be chosen high enough to get an acceptable current. However, to the extent that the noise on the power supply can be transmitted to the pins, the resistor values might be chosen to be lower. A filter capacitor from UV to -VIN or OV to -VIN is a possibility, if certain transients need to be filtered. (Note that even some transients which could momentarily shut off the GATE might recover fast enough such that the GATE or the output current does not even see the interruption). Finally, take into account whether the resistor values are readily available, or need to be custom ordered. Tolerances of 1% are recommended for accuracy. Note that for a typical 48V system (with a 43V to 72V range), the 43V or 72V is being divided down to 1.255V, a significant scaling factor. For UV, the ratio is roughly 35 times; every 3mV change on the UV pin represents roughly 0.1V change of power supply voltage. Conversely, an error of 3mV (due to the resistors, for example) results in an error of 0.1V for the supply trip point. The OV ratio is around 60. So the accuracy of the resistors comes into play. FIGURE 33. HARD FAULT SHUTDOWN AND RETRY As in the Over-Current Time-Out response discussed previously, the supply is set at -48V and the current limit is set at 2.5A. After the initial gate shutdown (10s) a soft start is initiated with the short circuit still present. As the GATE slowly turns on the current ramps up and exceeds the OverCurrent threshold (50mV) enabling the timer and current limiting (2.5A). The fault remains for the duration of the timeout period and the GATE pin is quickly pulled low and latched off. Applications: OV and UV The UV and OV pins can be used to detect Over-Voltage and Under-Voltage conditions on the input supply and quickly shut down the external FET to protect the system. Each pin is tied to an internal comparator with a nominal reference of 1.255V. A resistor divider between the VDD (gnd) and -VIN is typically used to set the trip points on the UV and OV pins. If the voltage on the UV pin is above its threshold and the voltage on the OV pin is below its threshold, the supply is 18 The hysteresis of the comparators is also multiplied by the scale factor of 35 for the UV pin (35 * 135mV = 4.7V of hysteresis at the power supply) and 60 for the OV pin (60 * 25mV = 1.5V of hysteresis at the power supply). With the three resistors, the UV equation is based on the simple resistor divider: 1.255 = VUV [(R5 + R6)/(R4 + R5 + R6)] or VUV = 1.255 [(R4 + R5 + R6)/(R5 + R6)] Similarly, for OV: 1.255 = VOV [(R6)/(R4 + R5 + R6)] or VOV = 1.255 [(R4 + R5 + R6)/(R6)] Note that there are two equations, but 3 unknowns. Because of the scale factor, R4 has to be much bigger than the other two; chose its value first, to set the current (for example, 50V / 500k draws 100A), and then the other two will be in the 10k range. Solve the two equations for two unknowns. Note that some iteration may be necessary to select values that meet the requirement, and are also readily available standard values. The three resistor divider (R4, R5, R6) is the recommended approach for most applications, but if acceptable values can't ISL6142, ISL6152 Applications: PWRGD/PWRGD The PWRGD/PWRGD outputs are typically used to directly enable a power module, such as a DC/DC converter. The PWRGD (ISL6142) is used for modules with active low enable (L version), and PWRGD (ISL6152) for those with an active high enable (H version). The modules usually have a pull-up device built-in, as well as an internal clamp. If not, an external pull-up resistor may be needed. If the pin is not used, it can be left open. For both versions at initial start-up, when the DRAIN to VEE voltage differential is less than 1.3V and the GATE voltage is within 2.5V (VGH) of its normal operating voltage (13.6V), power is considered good and the PWRGD/PWRGD pins will go active. At this point the output is latched and the comparators above no longer control the output. However a second DRAIN comparator remains active and will drive the PWRGD/PWRGD output inactive if the DRAIN voltage exceeds VEE by more than 8V. The latch is reset by any of the signals that shut off the GATE (Over-Voltage, UnderVoltage; Under-Voltage-Lock-Out; Over-Current Time-Out, disable pin high, or powering down). In this case the PWRGD/PWRGD output will go inactive, indicating power is no longer good. ISL6142 (L version; Figure 34): Under normal conditions (DRAIN voltage - VEE < VPG, and VGATE - VGATE < VGH) the Q2 DMOS will turn on, pulling PWRGD low, enabling the module. signal it is driving. An external clamp may be used to limit the voltage range. VDD VIN+ VOUT+ VGATE + - be found, then consider 2 separate resistor dividers (one for each pin, both from VDD to -VIN). This also allows the user to adjust or trim either trip point independently. Some applications employ a short pin ground on the connector tied to R4 to ensure the hot plug device is fully powered up before the UV and OV pins (tied to the short pin ground) are biased. This ensures proper control of the GATE is maintained during power up. This is not a requirement for the ISL6142/52 however the circuit will perform properly if a short pin scheme is implemented (reference Figure 38). VGH GATE VPG + - (SECTION OF) ISL6142 (L VERSION) + - VEE VDH + - + CL LATCH Q2 LOGIC VEE + - 19 ON/OFF ACTIVE LOW ENABLE MODULE VIN- VOUT- VEE DRAIN FIGURE 34. ACTIVE LOW ENABLE MODULE The PWRGD can also drive an opto-coupler (such as a 4N25), as shown in Figure 35 or LED (Figure 36). In both cases, they are on (active) when power is good. Resistors R13 or R14 are chosen based on the supply voltage, and the amount of current needed by the loads. VDD (SECTION OF) ISL6142 (L VERSION) LOGIC PWRGD R13 PWRGD Q2 OPTO LATCH COMPARATORS VEE DRAIN FIGURE 35. ACTIVE LOW ENABLE OPTO-ISOLATOR VDD (SECTION OF) ISL6142 (L VERSION) LOGIC When any of the 5 conditions occur that turn off the GATE (OV, UV, UVLO, Over-Current Time-Out, disable pin high) the PWRGD latch is reset and the Q2 DMOS device will shut off (high impedance). The pin will quickly be pulled high by the external module (or an optional pull-up resistor or equivalent) which in turn will disable it. If a pull-up resistor is used, it can be connected to any supply voltage that doesn't exceed the IC pin maximum ratings on the high end, but is high enough to give acceptable logic levels to whatever PWRGD + PWRGD R14 Q2 LED (GREEN) LATCH COMPARATORS VEE DRAIN FIGURE 36. ACTIVE LOW ENABLE LED ISL6152 (H version; Figure 37): Under normal conditions (DRAIN voltage - VEE < VPG, and VGATE - VGATE < VGH), the Q3 DMOS will be on, shorting the bottom of the internal resistor to VEE, turning Q2 off. If the pull-up current from the external module is high enough, the voltage drop across the 6.2k resistor will look like a logic high (relative to DRAIN). Note that the module is only referenced to DRAIN, not VEE ISL6142, ISL6152 (but under normal conditions, the FET is on, and the DRAIN and VEE are almost the same voltage). When any of the 5 conditions occur that turn off the GATE, the Q3 DMOS turns off, and the resistor and Q2 clamp the PWRGD pin to one diode drop (~0.7V) above the DRAIN pin. This should be able to pull low against the module pull-up current, and disable the module. VDD VIN+ VOUT+ + - VGATE VGH GATE VPG + - + + - VEE VDH + - PWRGD (SECTION OF) ISL6152 (H VERSION) ON/OFF 6.2K Q2 + CL LATCH Q3 LOGIC VEE + - ACTIVE HIGH ENABLE MODULE VIN- VOUT- VEE DRAIN FIGURE 37. ACTIVE HIGH ENABLE MODULE Applications: GATE Pin a high enough input voltage (remember that current through the RPG 6.2k resistor generates the high voltage level; see Figure 34). The input capacitance of the brick is chosen to match its system requirements, such as filtering noise, and maintaining regulation under varying loads. Note that this input capacitance appears as the load capacitance of the ISL6142/52. The brick's output capacitance is also determined by the system, including load regulation considerations. However, it can affect the ISL6142/52, depending upon how it is enabled. For example, if the PWRGD/PWRGD signal is not used to enable the brick, the following could occur. Sometime during the inrush current time, as the main power supply starts charging the brick input capacitors, the brick itself will start working, and start charging its output capacitors and load; that current has to be added to the inrush current. In some cases, the sum could exceed the Over-Current threshold, which could shut down the system if the time-out period is exceeded! Therefore, whenever practical, it is advantageous to use the PWRGD/PWRGD output to keep the brick off at least until the input caps are charged up, and then start-up the brick to charge its output caps. To help protect the external FET, the output of the GATE pin is internally clamped; up to an 80V supply and will not be any higher than 15V. Under normal operation when the supply voltage is above 20V, the GATE voltage will be regulated to a nominal 13.6V above VEE. Typical brick regulators include models such as Lucent JW050A1-E or Vicor VI-J30-CY. These are nominal -48V input, and 5V outputs, with some isolation between the input and output. Applications: "Brick" Regulators Applications: Optional Components One of the typical loads used are DC/DC regulators, some commonly known as "brick" regulators, (partly due to their shape, and because it can be considered a "building block" of a system). For a given input voltage range, there are usually whole families of different output voltages and current ranges. There are also various standardized sizes and pinouts, starting with the original "full" brick, and since getting smaller (half-bricks and quarter-bricks are now common). In addition to the typical application, and the variations already mentioned, there are a few other possible components that might be used in specific cases. See Figure 38 for some possibilities. Other common features may include: all components (except some filter capacitors) are self-contained in a molded plastic package; external pins for connections; and often an ENABLE input pin to turn it on or off. A hot plug IC, such as the ISL6142 is often used to gate power to a brick, as well as turn it on. Many bricks have both logic polarities available (Enable high or low input); select the ISL6142 (L-version) or ISL6152 (Hversion) to match. There is little difference between them, although the L-version output is usually simpler to interface. The Enable input often has a pull-up resistor or current source, or equivalent built in; care must be taken in the ISL6152 (H version) output that the given current will create 20 If the input power supply exceeds the 100V absolute maximum rating, even for a short transient, that could cause permanent damage to the IC, as well as other components on the board. If this cannot be guaranteed, a voltage suppressor (such as the SMAT70A, D1) is recommended. When placed from VDD to -VIN on the board, it will clamp the voltage. If transients on the input power supply occur when the supply is near either the OV or UV trip points, the GATE could turn on or off momentarily. One possible solution is to add a filter cap C4 to the VDD pin, through isolation resistor R11. A large value of R11 is better for the filtering, but be aware of the voltage drop across it. For example, a 1k resistor, with 2.4mA of IDD would have 2.4V across it and dissipate 2.4mW. Since the UV and OV comparators are referenced with respect to VEE, they should not be affected, but the GATE clamp voltage could be offset by the voltage across the extra resistor. ISL6142, ISL6152 R12 is a pull-up resistor for PWRGD, if there is no other component acting as a pull-up device. The value of R12 is determined by how much current is needed when the pin is pulled low (also affected by the VDD voltage); and it should be pulled low enough for a good logic low level. An LED can also be placed in series with R12, if desired. In that case, the criteria is the LED brightness versus current. The switch SW1 is shown as a simple push button. It can be replaced by an active switch, such as an NPN or NFET; the principle is the same; pull the UV node below its trip point, and then release it (toggle low). To connect an NFET, for example, the DRAIN goes to UV; the source to -VIN, and the GATE is the input; if it goes high (relative to -VIN), it turns the NFET on, and UV is pulled low. Just make sure the NFET resistance is low compared to the resistor divider, so that it has no problem pulling down against it. GND (SHORT PIN) GND GND Logic Supply (VEE+5V) R10 R11* R12* VDD FAULT DIS ISOUT PWRGD R4 ISL6142 UV R5 TO ADC R6 SW1* D1* Logic Input Q2 R9 OV CT VEE ISC3 IS+ SENSE GATE R7 C1 R8 R2 DRAIN R3 C2 C4* CL RL -48V IN R1 Q1 -48V OUT FIGURE 38. ISL6142/52 OPTIONAL COMPONENTS (SHOWN WITH *) Applications: Layout Considerations For the minimum application, there are 10 resistors, 3 capacitors, one IC and 2 FETs. A sample layout is shown in Figure 39. It assumes the IC is 8-SOIC; Q1 is in a D2PAK (or similar SMD-220 package). Although GND planes are common with multi-level PCBs, for a -48V system, the -48V rails (both input and output) act more like a GND than the top 0V rail (mainly because the IC signals are mostly referenced to the lower rail). So if separate planes for each voltage are not an option, consider prioritizing the bottom rails first. Note that with the placement shown, most of the signal lines are short, and there should be minimal interaction between them. Although decoupling capacitors across the IC supply pins are often recommended in general, this application may not need one, nor even tolerate one. For one thing, a decoupling cap would add to (or be swamped out by) any other input capacitance; it also needs to be charged up when power is applied. But more importantly, there are no high speed (or any) input signals to the IC that need to be conditioned. If still 21 desired, consider the isolation resistor R10, as shown in figure 38. NOTE: 1. Layout scale is approximate; routing lines are just for illustration purposes; they do not necessarily conform to normal PCB design rules. High current buses are wider, shown with parallel lines. 2. Approximate size of the above layout is 0.8 x 0.8 inches, excluding Q1 (D2PAK or similar SMD-220 package). 3. R1 sense resistor is size 2512; all other R's and C's shown are 0805; they can all potentially use smaller footprints, if desired. 4. The RL and CL are not shown on the layout. 5. Vias are needed to connect R4 and VDD to GND on the bottom of the board, and R8 to pin 9; all other routing can be on the top level. 6. PWRGD signal is not used here. ISL6142, ISL6152 BOM (Bill Of Materials) R9 = 4.99K (1%) R1 = 0.02 (5%) R10 = 5.10K (10%) R2 =10.0 (5%) C1 = 150nF (25V) R3 = 18.0K (10%) C2 = 3.3nF (100V) R4 = 549K (1%) C3 = 1500pF (25V) R5 = 6.49K (1%) Q1 = IRF530 (100V, 17A, 0.11) R6 = 10.0K (1%) Q2 = N-channel Logic FEFT R7 = R8 = 400 (1%) GND GND TO VDD R9 -48VIN C3 +5V LOGIC IN -48VIN R10 G D S 1 PG VDD 14 2 FLT CT 13 3 DIS ISO 12 4 OV R5 GND GATE NFET R3 R6 -48VIN C2 R4 ISL6142 D 11 5 UV G 10 6 IS- IS+ 9 7 VEE S8 R7 -48V IN DRAIN R2 C1 R8 SOURCE TO PIN 9 R1 FIGURE 39. ISL6142 SAMPLE LAYOUT (NOT TO SCALE) 22 -48V OUT ISL6142, ISL6152 Small Outline Plastic Packages (SOIC) M14.15 (JEDEC MS-012-AB ISSUE C) N INDEX AREA 0.25(0.010) M H 14 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE B M E INCHES -B- SYMBOL 1 2 3 L SEATING PLANE -A- h x 45o A D -C- e A1 B 0.10(0.004) 0.25(0.010) M C A M 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.1890 0.1968 4.80 5.00 3 E 0.1497 0.1574 3.80 4.00 4 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 8o 0o B S NOTES: MAX A1 e C MILLIMETERS MIN N 8 0o 8 7 8o 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. Rev. 0 12/93 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width "B", as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 23