Surface Mount Oven Stabilized Oscillator DOC Series Description: 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 1028 0F 05 DOC0.0MHZ 1 Connor-Winfield's high stability DOC OCXO / OCVCXO series are exceptionally precise frequency standards, excellent for use in cellular base stations, test equipment, Synchronous Ethernet and VSAT applications. These true surface mount OCXO / OCVCXO provide frequency stabilities in the range of 20 ppb to 100 ppb, over the commercial, extended commercial or the industrial temperature range. The DOC series is available with a CMOS output along with optional Electronic Frequency Tuning (OCVCXO). These oscillators provide outstanding phase noise characteristics that will meet the most stringent requirements. Features: OCXO / OCVCXO 3.3 Vdc Operation SMT Package Frequency Stabilities Available: 20 ppb, 50 ppb or 100 ppb Temperature Ranges Available: 0 to 70C, -20 to 75, -40 to 85C or -40 to 70C Low Phase Noise LVCMOS Output Optional Electronic Frequency Tuning RoHS Compliant / Lead Free Package Outline 0.307 (7.80mm) DOC050F 10.0 MHz 0.555 (14.1mm) Suggested Pad Layout 0.060 (1.52mm) 0.085 (2.16mm) 4 0.100 (2.54mm) 0.260 (6.60mm) 0.100 (2.54mm) 0.040 (1.02mm) 0.040 (1.02mm) 0.025 (0.64mm) Top View 0.085 (2.16mm) 3 Top 5 View 2 6 1 Keep Out Area DNC = Do Not Connect DNC Bottom View Side View 0.375 (9.52mm) 0.060 (1.52mm) DNC 0.275 (6.99mm) 1 1335 0.358 (9.1mm) Dimensional Tolerance: +/-0.005 (0.127mm) Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Pad Connections 1: N/C or Vc option 2: Do Not Connect* 3 Ground: 4: Output 5: Do Not Connect* 6: Supply Voltage (Vcc) *DO NOT connect "DNC" pads to ground or supply rails. Ordering Information Bulletin Page Revision Date Cx207 1 of 4 19 14 Aug 2013 DOC 05 Oscillator Type Frequency Stability 3.3 Vdc LVCMOS Output Surface Mount OCXO 02 = 20 ppb 05 = 50 ppb 10 = 100 ppb 25 = 250 ppb 0 F Temperature Range Voltage Control Option 0 = 0 to 70C 1 = -20 to 75C 2 = -40 to 85C 3 = -40 to 70C F = OCXO (Fixed Freq.) V = OCVCXO (Voltage Controlled) -010.0M Output Frequency Frequency Format -xxx.xM Min.* -xxx.xxxxxxM Max* *Amount of numbers after the decimal point. M = MHz Example Part Numbers: DOC050F-010.0M = 9x14mm package, 50 ppb, 0 to 70C, 3.3 Vdc, CMOS Output, OCXO, Output Frequency 10.0 MHz DOC022V-020.0M = 9x14mm package, 20 ppb, -40 to 85C, 3.3 Vdc, CMOS Output, OCVCXO, 20.0 MHz Specifications subject to change without notification. See Connor-Winfield's website for latest revision. Not intended for life support applications. All dimensions in inches. (c) Copyright 2013 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Absolute Maximum Ratings Parameter Minimum Storage Temperature Supply Voltage - 3.3 Vdc (Vcc) Control Voltage (Vc) -55 -0.5 -0.5 Nominal - Maximum Units Notes Maximum Units Notes ppb ppb ppb 1 1 1 C C C C ppm ppb ppb ppb/day ppb ppm Vdc 2 5% 5% 3 3 4 5 125 4.5 Vcc+0.5 C Vdc Vdc Operating Specifications Parameter Minimum Nominal Center Frequency: (Fo) 10, 12.8, 19.44, 20, 25, 38.88, 40, 50 or 80 Frequency Stability vs. Change in Temperature: (See Ordering Information) Stability Code 02 -20.0 20.0 Stability Code 05 -50.0 50.0 Stability Code 10 -100.0 100.0 Operating Temperature Range: (See Ordering Information) Temperature Code 0 0 70 Temperature Code 1 -20 75 Temperature Code 2 -40 85 Temperature Code 3 -40 70 Frequency Calibration: -1.0 1.0 Frequency Stability vs Load -20 20 Frequency Stability vs Voltage -20 20 Aging: Daily: -10 10 Aging: First Year: -300 300 Total Frequency Tolerance (20 Years) -4.60 4.60 Supply Voltage: (Vcc) 3.13 3.30 3.47 Power Consumption: Vcc = Nominal Voltage Commercial Temperature Range, 0 to 70 C Turn On 2.5 Steady State @ 25C 1.1 Industrial Temperature Range, -40 to 85 C Turn On 3.0 Steady State @ 25C 1.3 Phase Jitter: (BW: 12 KHz to Fo/2) 0.5 1.0 Short Term Stability 1.0E-9/s Start-Up Time: 10 Warm Up Time (Within Specification @ 25C) 60 Warm Up Time (Within Specification @ -40C) 90 MHz W W W W ps RMS ms s s CMOS Output Characteristics Parameter Load Output Voltage: Output Voltage: High (Voh) Low (Vol) Output Current: High (Ioh) Low (Iol) Duty Cycle at 50% of Vcc Rise / Fall Time: 10% to 90% - Minimum Nominal Maximum Units 2.7 45 - 50 - 0.3 -4 4 55 6.5 V V mA mA % ns Maximum Units - 15 - Notes pF 6 OCVCXO Input Characteristics (Optional) Parameter Control Voltage Range: Frequency Pullability: Input Impedance Linearity Minimum 0.30 10.0 100K 5 Nominal 1.65 - 3.00 - Bulletin Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Notes V ppm Ohms % Page Revision Date 7 8 Cx207 2 of 4 19 14 Aug 2013 Specifications subject to change without notification. See Connor-Winfield's website for latest revision. Not intended for life support applications. All dimensions in inches. (c) Copyright 2013 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Parameter @ 1 Hz offset @ 10 Hz offset @ 100 Hz offset @ 1 KHz offset @ 10 KHz offset @ 100 KHz offset Phase Noise Characteristics Typical Phase Noise for DOC050F - 010.0M Minimum - Nominal -67 -100 -130 -148 -154 -155 Maximum - Units dBC/Hz dBC/Hz dBC/Hz dBC/Hz dBC/Hz dBC/Hz Notes Package Characteristics DOC Package Package consisting of a FR-4 substrate and Ryton-R-4 cover. Water Resistant package, non-hermetic seal. (Engineering Properties of Ryton R-4 Application Note AN2100) Environmental Characteristics Shock 500 G's 1ms, Halfsine, 3 shocks per direction, per MIL-STD 202G, Method 213B Test Condition D. Sinusoidal Vibration 0.06" D.A. or 10G's Peak, 10 to 500 Hz, per MIL-STD-202G, Method 204D, Test Condition A. Random Vibration 5.35 G's rms. 20 to 2000 Hz per MIL-STD-202G, Method 214,Test Condition 1A, 15 minutes each axis. Moisture 10 cycles, 95% RH, Per MIL-STD-202G, Method 112. Marking Permanency Per MIL-STD-202G, Method 215J. Solder Process Recommendations: RoHS compliant, lead free. See solder profile on page 4. In-line reflow: Refer to recommended reflow pre-heat and reflow temperatures on page 4. Package material consist of Ryton R-4 high temperature cover with FR4 substrate. Component solder is Pb free high temperature eutectic alloy with a melting point of 221C.| In-line oven profile: We recommend using KIC profiler or similar device placing one of the thermocouples on the device to insure that the internal package temperature does not exceed 221C. Removal of device: If for any reason the device needs to be removed from the board, use a temperature controlled repair station with profile monitoring capabilities. Following a monitored profile will insure the device is properly pre-heated prior to relow. Refer to IPC 610E for inspection guidelines. Recommended Cleaning Process: (If required) Device is non-hermetic, water resistance with four weep holes, one in each corner to allow moisture to be removed during the drying cycle. We recommend in-line warm water wash with air knife and drying capabilities. If cleaner does not have drying capability, then use hot air circulated oven. Boards should be placed in the oven vertically for good water runoff Device must be dried properly prior to use! Note: If saponifier is used make sure the device is rinsed properly to insure all residues are removed. PH of saponifier should not exceed 10. Drying Temperature: Between 85 to 100C. Drying Time: Time will vary depending on the board size. Caution: Do not submerge the device! Notes: 1. Frequency stability vs. change in temperature. [(Fmax - Fmin)/(2*Fo)]. 2. Initial calibration @ 25C. For OCVCXO control voltage must be fixed. 3. After 30 days of operation 4. Inclusive of calibration @ 25C, frequency vs. change in temperature, change in supply voltage (5%), load change (5%), shock and vibration and 20 years aging 5. Minimum "Power On Time" after rail rises from 0 to within +/-5% of Vcc = 1 second. Vcc ramp rate must be <0.3 volts per millisecond. 6. Attention: To achieve optimal frequency stability, and in some cases to meet the specification stated on this data sheet, it is required that the circuit connected to this OCXO output must have the equivalent input capacitance that is specified by the nominal load capacitance. Deviations from the nominal load capacitance will have a graduated effect on the stability of approximately 20 ppb per pF load difference. 7. Positive slope. (Frequency increases as Vc voltage increases. To ensure proper operation of OCVCXO's the control voltage input must be biased the nominal control voltage. Failure to bias the Vc input will cause an unstable output condition. 8. Referenced to Fo. Bulletin Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. Not intended for life support applications. All dimensions in inches. (c) Copyright 2013 The Connor-Winfield Corporation Cx207 3 of 4 19 14 Aug 2013 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com CMOS Output Waveform CMOS Test Circuit DNC Output 10uF to 100 uF 0.01uF 2 DNC Pad 1 OCXO = N/C OCVCXO = Vc Phase Noise Plot 15 pF DNC = Do Not Connect DO NOT connect "DNC" pads to ground or supply rails. RoHS Solder Profile Typical phase noise plot for DOC050F-010.0M Temperature 260C 260C 220C 180C 150C 120C 0 10 s Up to 120 s 60 to 90 s Typical Typical Meets IPC/JEDEC J-STD-020C Tape and Reel Information 1028 DOC050F 10.0 MHZ SM-MECH42 Bulletin Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. Not intended for life support applications. All dimensions in inches. (c) Copyright 2013 The Connor-Winfield Corporation Cx207 4 of 4 19 14 Aug 2013