DDR3L SDRAM
MT41K1G4 – 128 Meg x 4 x 8 banks
MT41K512M8 – 64 Meg x 8 x 8 banks
MT41K256M16 – 32 Meg x 16 x 8 banks
Description
DDR3L SDRAM (1.35V) is a low voltage version of the
DDR3 (1.5V) SDRAM. Refer to DDR3 (1.5V) SDRAM
(Die Rev :E) data sheet specifications when running in
1.5V compatible mode.
Features
•V
DD = VDDQ = 1.35V (1.283–1.45V)
• Backward compatible to VDD = VDDQ = 1.5V ±0.075V
– Supports DDR3L devices to be backward com-
patible in 1.5V applications
• Differential bidirectional data strobe
•8n-bit prefetch architecture
• Differential clock inputs (CK, CK#)
• 8 internal banks
• Nominal and dynamic on-die termination (ODT)
for data, strobe, and mask signals
• Programmable CAS (READ) latency (CL)
• Programmable posted CAS additive latency (AL)
• Programmable CAS (WRITE) latency (CWL)
• Fixed burst length (BL) of 8 and burst chop (BC) of 4
(via the mode register set [MRS])
• Selectable BC4 or BL8 on-the-fly (OTF)
• Self refresh mode
•T
C of 105°C
– 64ms, 8192-cycle refresh up to 85°C
– 32ms, 8192-cycle refresh at >85°C to 95°C
– 16ms, 8192-cycle refresh at >95°C to 105°C
• Self refresh temperature (SRT)
• Automatic self refresh (ASR)
• Write leveling
• Multipurpose register
• Output driver calibration
Options Marking
• Configuration
– 1 Gig x 4 1G4
– 512 Meg x 8 512M8
– 256 Meg x 16 256M16
• FBGA package (Pb-free) – x4, x8
– 78-ball (9mm x 10.5mm) Rev. E RH
– 78-ball (7.5mm x 10.6mm) Rev. N RG
– 78-ball (8mm x 10.5mm) Rev. P DA
• FBGA package (Pb-free) – x16
– 96-ball (9mm x 14mm) Rev. E HA
– 96-ball (7.5mm x 13.5mm) Rev. N LY
– 96-ball (8mm x 14mm) Rev. P TW
• Timing – cycle time
– 938ps @ CL = 14 (DDR3-2133) -093
– 1.07ns @ CL = 13 (DDR3-1866) -107
– 1.25ns @ CL = 11 (DDR3-1600) -125
• Operating temperature
– Commercial (0°C TC +95°C) None
– Industrial (–40°C TC +95°C) IT
– Automotive (–40°C TC +105°C) AT
• Revision :E/:N/:P
Table 1: Key Timing Parameters
Speed Grade Data Rate (MT/s) Target tRCD-tRP-CL tRCD (ns) tRP (ns) CL (ns)
-093 1, 2 2133 14-14-14 13.09 13.09 13.09
-107 1 1866 13-13-13 13.91 13.91 13.91
-125 1600 11-11-11 13.75 13.75 13.75
Notes: 1. Backward compatible to 1600, CL = 11 (-125).
2. Backward compatible to 1866, CL = 13 (-107).
4Gb: x4, x8, x16 DDR3L SDRAM
Description
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 1Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are subject to change by Micron without notice.
Table 2: Addressing
Parameter 1 Gig x 4 512 Meg x 8 256 Meg x 16
Configuration 128 Meg x 4 x 8 banks 64 Meg x 8 x 8 banks 32 Meg x 16 x 8 banks
Refresh count 8K 8K 8K
Row address 64K (A[15:0]) 64K (A[15:0]) 32K (A[14:0])
Bank address 8 (BA[2:0]) 8 (BA[2:0]) 8 (BA[2:0])
Column address 2K (A[11, 9:0]) 1K (A[9:0]) 1K (A[9:0])
Page size 1KB 1KB 2KB
Figure 1: DDR3L Part Numbers
([DPSOH3DUW1XPEHU 07.0'$3
&RQILJXUDWLRQ
*LJ[
0HJ[
0HJ[
*
0
0
&RQILJXUDWLRQ
07. 3DFNDJH 6SHHG
5HYLVLRQ
5HYLVLRQ
(13
&RPPHUFLDO
,QGXVWULDOWHPSHUDWXUH
^
1RQH
,7
$XWRPRWLYHWHPSHUDWXUH $7
3DFNDJH
EDOOPP[PP)%*$
0DUN
+$
5HY
(
EDOOPP[PP)%*$
5+(
6SHHG*UDGH
W
&. QV&/ 
W
&. QV&/ 


7HPSHUDWXUH
EDOOPP[PP)%*$
3'$
W
&. QV&/ 

EDOOPP[PP)%*$
EDOOPP[PP)%*$
1
1
5*
/<
EDOOPP[PP)%*$
37:
Note: 1. Not all options listed can be combined to define an offered product. Use the part catalog search on
http://www.micron.com for available offerings.
FBGA Part Marking Decoder
Due to space limitations, FBGA-packaged components have an abbreviated part marking that is different from the
part number. For a quick conversion of an FBGA code, see the FBGA Part Marking Decoder on Micron’s Web site:
http://www.micron.com.
4Gb: x4, x8, x16 DDR3L SDRAM
Description
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 2Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Contents
Important Notes and Warnings ....................................................................................................................... 11
State Diagram ................................................................................................................................................ 12
Functional Description ................................................................................................................................... 13
Industrial Temperature ............................................................................................................................... 13
Automotive Temperature ............................................................................................................................ 13
General Notes ............................................................................................................................................ 14
Functional Block Diagrams ............................................................................................................................. 15
Ball Assignments and Descriptions ................................................................................................................. 17
Package Dimensions ....................................................................................................................................... 23
Electrical Specifications .................................................................................................................................. 29
Absolute Ratings ......................................................................................................................................... 29
Input/Output Capacitance .......................................................................................................................... 30
Thermal Characteristics .................................................................................................................................. 31
Electrical Specifications – IDD Specifications and Conditions ............................................................................ 33
Electrical Characteristics – Operating IDD Specifications .................................................................................. 44
Electrical Specifications – DC and AC .............................................................................................................. 49
DC Operating Conditions ........................................................................................................................... 49
Input Operating Conditions ........................................................................................................................ 50
DDR3L 1.35V AC Overshoot/Undershoot Specification ................................................................................ 54
DDR3L 1.35V Slew Rate Definitions for Single-Ended Input Signals .............................................................. 57
DDR3L 1.35V Slew Rate Definitions for Differential Input Signals ................................................................. 59
ODT Characteristics ....................................................................................................................................... 60
1.35V ODT Resistors ................................................................................................................................... 61
ODT Sensitivity .......................................................................................................................................... 62
ODT Timing Definitions ............................................................................................................................. 62
Output Driver Impedance ............................................................................................................................... 66
34 Ohm Output Driver Impedance .............................................................................................................. 67
DDR3L 34 Ohm Driver ................................................................................................................................ 68
DDR3L 34 Ohm Output Driver Sensitivity .................................................................................................... 69
DDR3L Alternative 40 Ohm Driver ............................................................................................................... 70
DDR3L 40 Ohm Output Driver Sensitivity .................................................................................................... 70
Output Characteristics and Operating Conditions ............................................................................................ 72
Reference Output Load ............................................................................................................................... 75
Slew Rate Definitions for Single-Ended Output Signals ................................................................................. 75
Slew Rate Definitions for Differential Output Signals .................................................................................... 77
Speed Bin Tables ............................................................................................................................................ 78
Electrical Characteristics and AC Operating Conditions ................................................................................... 83
Command and Address Setup, Hold, and Derating .......................................................................................... 103
Data Setup, Hold, and Derating ...................................................................................................................... 110
Commands – Truth Tables ............................................................................................................................. 118
Commands ................................................................................................................................................... 121
DESELECT ................................................................................................................................................ 121
NO OPERATION ........................................................................................................................................ 121
ZQ CALIBRATION LONG ........................................................................................................................... 121
ZQ CALIBRATION SHORT .......................................................................................................................... 121
ACTIVATE ................................................................................................................................................. 121
READ ........................................................................................................................................................ 121
WRITE ...................................................................................................................................................... 122
PRECHARGE ............................................................................................................................................. 123
REFRESH .................................................................................................................................................. 123
4Gb: x4, x8, x16 DDR3L SDRAM
Description
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 3Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
SELF REFRESH .......................................................................................................................................... 124
DLL Disable Mode ..................................................................................................................................... 125
Input Clock Frequency Change ...................................................................................................................... 129
Write Leveling ............................................................................................................................................... 131
Write Leveling Procedure ........................................................................................................................... 133
Write Leveling Mode Exit Procedure ........................................................................................................... 135
Initialization ................................................................................................................................................. 136
Voltage Initialization/Change ........................................................................................................................ 138
VDD Voltage Switching ............................................................................................................................... 139
Mode Registers .............................................................................................................................................. 140
Mode Register 0 (MR0) ................................................................................................................................... 141
Burst Length ............................................................................................................................................. 141
Burst Type ................................................................................................................................................. 142
DLL RESET ................................................................................................................................................ 143
Write Recovery .......................................................................................................................................... 144
Precharge Power-Down (Precharge PD) ...................................................................................................... 144
CAS Latency (CL) ....................................................................................................................................... 144
Mode Register 1 (MR1) ................................................................................................................................... 146
DLL Enable/DLL Disable ........................................................................................................................... 146
Output Drive Strength ............................................................................................................................... 147
OUTPUT ENABLE/DISABLE ...................................................................................................................... 147
TDQS Enable ............................................................................................................................................. 147
On-Die Termination .................................................................................................................................. 148
WRITE LEVELING ..................................................................................................................................... 148
POSTED CAS ADDITIVE Latency ................................................................................................................ 148
Mode Register 2 (MR2) ................................................................................................................................... 149
CAS Write Latency (CWL) ........................................................................................................................... 150
AUTO SELF REFRESH (ASR) ....................................................................................................................... 150
SELF REFRESH TEMPERATURE (SRT) ........................................................................................................ 150
SRT vs. ASR ............................................................................................................................................... 151
DYNAMIC ODT ......................................................................................................................................... 151
Mode Register 3 (MR3) ................................................................................................................................... 151
MULTIPURPOSE REGISTER (MPR) ............................................................................................................ 152
MPR Functional Description ...................................................................................................................... 153
MPR Register Address Definitions and Bursting Order ................................................................................. 154
MPR Read Predefined Pattern .................................................................................................................... 159
MODE REGISTER SET (MRS) Command ........................................................................................................ 159
ZQ CALIBRATION Operation ......................................................................................................................... 160
ACTIVATE Operation ..................................................................................................................................... 161
READ Operation ............................................................................................................................................ 163
WRITE Operation .......................................................................................................................................... 174
DQ Input Timing ....................................................................................................................................... 182
PRECHARGE Operation ................................................................................................................................. 184
SELF REFRESH Operation .............................................................................................................................. 184
Extended Temperature Usage ........................................................................................................................ 186
Power-Down Mode ........................................................................................................................................ 187
RESET Operation ........................................................................................................................................... 195
On-Die Termination (ODT) ............................................................................................................................ 197
Functional Representation of ODT ............................................................................................................. 197
Nominal ODT ............................................................................................................................................ 197
Dynamic ODT ............................................................................................................................................... 199
Dynamic ODT Special Use Case ................................................................................................................. 199
4Gb: x4, x8, x16 DDR3L SDRAM
Description
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 4Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Functional Description .............................................................................................................................. 199
Synchronous ODT Mode ................................................................................................................................ 205
ODT Latency and Posted ODT .................................................................................................................... 205
Timing Parameters .................................................................................................................................... 205
ODT Off During READs .............................................................................................................................. 208
Asynchronous ODT Mode .............................................................................................................................. 210
Synchronous to Asynchronous ODT Mode Transition (Power-Down Entry) .................................................. 212
Asynchronous to Synchronous ODT Mode Transition (Power-Down Exit) ........................................................ 214
Asynchronous to Synchronous ODT Mode Transition (Short CKE Pulse) ...................................................... 216
4Gb: x4, x8, x16 DDR3L SDRAM
Description
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 5Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
List of Figures
Figure 1: DDR3L Part Numbers ........................................................................................................................ 2
Figure 2: Simplified State Diagram ................................................................................................................. 12
Figure 3: 1 Gig x 4 Functional Block Diagram .................................................................................................. 15
Figure 4: 512 Meg x 8 Functional Block Diagram ............................................................................................. 16
Figure 5: 256 Meg x 16 Functional Block Diagram ........................................................................................... 16
Figure 6: 78-Ball FBGA – x4, x8 (Top View) ...................................................................................................... 17
Figure 7: 96-Ball FBGA – x16 (Top View) ......................................................................................................... 18
Figure 8: 78-Ball FBGA – x4, x8 (RH) ............................................................................................................... 23
Figure 9: 78-Ball FBGA – x4, x8 (RG) ............................................................................................................... 24
Figure 10: 78-Ball FBGA – x4, x8 (DA) ............................................................................................................. 25
Figure 11: 96-Ball FBGA – x16 (HA) ................................................................................................................. 26
Figure 12: 96-Ball FBGA – x16 (LY) .................................................................................................................. 27
Figure 13: 96-Ball FBGA – x16 (TW) ................................................................................................................ 28
Figure 14: Thermal Measurement Point ......................................................................................................... 31
Figure 15: DDR3L 1.35V Input Signal .............................................................................................................. 53
Figure 16: Overshoot ..................................................................................................................................... 54
Figure 17: Undershoot ................................................................................................................................... 55
Figure 18: VIX for Differential Signals .............................................................................................................. 55
Figure 19: Single-Ended Requirements for Differential Signals ........................................................................ 55
Figure 20: Definition of Differential AC-Swing and tDVAC ............................................................................... 56
Figure 21: Nominal Slew Rate Definition for Single-Ended Input Signals .......................................................... 58
Figure 22: DDR3L 1.35V Nominal Differential Input Slew Rate Definition for DQS, DQS# and CK, CK# .............. 59
Figure 23: ODT Levels and I-V Characteristics ................................................................................................ 60
Figure 24: ODT Timing Reference Load .......................................................................................................... 63
Figure 25: tAON and tAOF Definitions ............................................................................................................ 64
Figure 26: tAONPD and tAOFPD Definitions ................................................................................................... 64
Figure 27: tADC Definition ............................................................................................................................. 65
Figure 28: Output Driver ................................................................................................................................ 66
Figure 29: DQ Output Signal .......................................................................................................................... 73
Figure 30: Differential Output Signal .............................................................................................................. 74
Figure 31: Reference Output Load for AC Timing and Output Slew Rate ........................................................... 75
Figure 32: Nominal Slew Rate Definition for Single-Ended Output Signals ....................................................... 76
Figure 33: Nominal Differential Output Slew Rate Definition for DQS, DQS# .................................................... 77
Figure 34: Nominal Slew Rate and tVAC for tIS (Command and Address – Clock) ............................................. 106
Figure 35: Nominal Slew Rate for tIH (Command and Address – Clock) ........................................................... 107
Figure 36: Tangent Line for tIS (Command and Address – Clock) .................................................................... 108
Figure 37: Tangent Line for tIH (Command and Address – Clock) .................................................................... 109
Figure 38: Nominal Slew Rate and tVAC for tDS (DQ – Strobe) ......................................................................... 114
Figure 39: Nominal Slew Rate for tDH (DQ – Strobe) ...................................................................................... 115
Figure 40: Tangent Line for tDS (DQ – Strobe) ................................................................................................ 116
Figure 41: Tangent Line for tDH (DQ – Strobe) ............................................................................................... 117
Figure 42: Refresh Mode ............................................................................................................................... 124
Figure 43: DLL Enable Mode to DLL Disable Mode ........................................................................................ 126
Figure 44: DLL Disable Mode to DLL Enable Mode ........................................................................................ 127
Figure 45: DLL Disable tDQSCK .................................................................................................................... 128
Figure 46: Change Frequency During Precharge Power-Down ........................................................................ 130
Figure 47: Write Leveling Concept ................................................................................................................. 131
Figure 48: Write Leveling Sequence ............................................................................................................... 134
Figure 49: Write Leveling Exit Procedure ....................................................................................................... 135
Figure 50: Initialization Sequence ................................................................................................................. 137
4Gb: x4, x8, x16 DDR3L SDRAM
Description
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 6Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Figure 51: VDD Voltage Switching .................................................................................................................. 139
Figure 52: MRS to MRS Command Timing (tMRD) ......................................................................................... 140
Figure 53: MRS to nonMRS Command Timing (tMOD) .................................................................................. 141
Figure 54: Mode Register 0 (MR0) Definitions ................................................................................................ 142
Figure 55: READ Latency .............................................................................................................................. 145
Figure 56: Mode Register 1 (MR1) Definition ................................................................................................. 146
Figure 57: READ Latency (AL = 5, CL = 6) ....................................................................................................... 149
Figure 58: Mode Register 2 (MR2) Definition ................................................................................................. 149
Figure 59: CAS Write Latency ........................................................................................................................ 150
Figure 60: Mode Register 3 (MR3) Definition ................................................................................................. 152
Figure 61: Multipurpose Register (MPR) Block Diagram ................................................................................. 153
Figure 62: MPR System Read Calibration with BL8: Fixed Burst Order Single Readout ..................................... 155
Figure 63: MPR System Read Calibration with BL8: Fixed Burst Order, Back-to-Back Readout .......................... 156
Figure 64: MPR System Read Calibration with BC4: Lower Nibble, Then Upper Nibble .................................... 157
Figure 65: MPR System Read Calibration with BC4: Upper Nibble, Then Lower Nibble .................................... 158
Figure 66: ZQ CALIBRATION Timing (ZQCL and ZQCS) ................................................................................. 160
Figure 67: Example: Meeting tRRD (MIN) and tRCD (MIN) ............................................................................. 161
Figure 68: Example: tFAW ............................................................................................................................. 162
Figure 69: READ Latency .............................................................................................................................. 163
Figure 70: Consecutive READ Bursts (BL8) .................................................................................................... 165
Figure 71: Consecutive READ Bursts (BC4) .................................................................................................... 165
Figure 72: Nonconsecutive READ Bursts ....................................................................................................... 166
Figure 73: READ (BL8) to WRITE (BL8) .......................................................................................................... 166
Figure 74: READ (BC4) to WRITE (BC4) OTF .................................................................................................. 167
Figure 75: READ to PRECHARGE (BL8) .......................................................................................................... 167
Figure 76: READ to PRECHARGE (BC4) ......................................................................................................... 168
Figure 77: READ to PRECHARGE (AL = 5, CL = 6) ........................................................................................... 168
Figure 78: READ with Auto Precharge (AL = 4, CL = 6) ..................................................................................... 168
Figure 79: Data Output Timing – tDQSQ and Data Valid Window .................................................................... 170
Figure 80: Data Strobe Timing – READs ......................................................................................................... 171
Figure 81: Method for Calculating tLZ and tHZ ............................................................................................... 172
Figure 82: tRPRE Timing ............................................................................................................................... 172
Figure 83: tRPST Timing ............................................................................................................................... 173
Figure 84: tWPRE Timing .............................................................................................................................. 175
Figure 85: tWPST Timing .............................................................................................................................. 175
Figure 86: WRITE Burst ................................................................................................................................ 176
Figure 87: Consecutive WRITE (BL8) to WRITE (BL8) ..................................................................................... 177
Figure 88: Consecutive WRITE (BC4) to WRITE (BC4) via OTF ........................................................................ 177
Figure 89: Nonconsecutive WRITE to WRITE ................................................................................................. 178
Figure 90: WRITE (BL8) to READ (BL8) .......................................................................................................... 178
Figure 91: WRITE to READ (BC4 Mode Register Setting) ................................................................................. 179
Figure 92: WRITE (BC4 OTF) to READ (BC4 OTF) ........................................................................................... 180
Figure 93: WRITE (BL8) to PRECHARGE ........................................................................................................ 181
Figure 94: WRITE (BC4 Mode Register Setting) to PRECHARGE ...................................................................... 181
Figure 95: WRITE (BC4 OTF) to PRECHARGE ................................................................................................ 182
Figure 96: Data Input Timing ........................................................................................................................ 183
Figure 97: Self Refresh Entry/Exit Timing ...................................................................................................... 185
Figure 98: Active Power-Down Entry and Exit ................................................................................................ 189
Figure 99: Precharge Power-Down (Fast-Exit Mode) Entry and Exit ................................................................. 189
Figure 100: Precharge Power-Down (Slow-Exit Mode) Entry and Exit .............................................................. 190
Figure 101: Power-Down Entry After READ or READ with Auto Precharge (RDAP) ........................................... 190
Figure 102: Power-Down Entry After WRITE .................................................................................................. 191
4Gb: x4, x8, x16 DDR3L SDRAM
Description
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 7Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Figure 103: Power-Down Entry After WRITE with Auto Precharge (WRAP) ...................................................... 191
Figure 104: REFRESH to Power-Down Entry .................................................................................................. 192
Figure 105: ACTIVATE to Power-Down Entry ................................................................................................. 192
Figure 106: PRECHARGE to Power-Down Entry ............................................................................................. 193
Figure 107: MRS Command to Power-Down Entry ......................................................................................... 193
Figure 108: Power-Down Exit to Refresh to Power-Down Entry ....................................................................... 194
Figure 109: RESET Sequence ......................................................................................................................... 196
Figure 110: On-Die Termination ................................................................................................................... 197
Figure 111: Dynamic ODT: ODT Asserted Before and After the WRITE, BC4 .................................................... 202
Figure 112: Dynamic ODT: Without WRITE Command .................................................................................. 202
Figure 113: Dynamic ODT: ODT Pin Asserted Together with WRITE Command for 6 Clock Cycles, BL8 ............ 203
Figure 114: Dynamic ODT: ODT Pin Asserted with WRITE Command for 6 Clock Cycles, BC4 .......................... 204
Figure 115: Dynamic ODT: ODT Pin Asserted with WRITE Command for 4 Clock Cycles, BC4 .......................... 204
Figure 116: Synchronous ODT ...................................................................................................................... 206
Figure 117: Synchronous ODT (BC4) ............................................................................................................. 207
Figure 118: ODT During READs .................................................................................................................... 209
Figure 119: Asynchronous ODT Timing with Fast ODT Transition .................................................................. 211
Figure 120: Synchronous to Asynchronous Transition During Precharge Power-Down (DLL Off) Entry ............ 213
Figure 121: Asynchronous to Synchronous Transition During Precharge Power-Down (DLL Off) Exit ............... 215
Figure 122: Transition Period for Short CKE LOW Cycles with Entry and Exit Period Overlapping ..................... 217
Figure 123: Transition Period for Short CKE HIGH Cycles with Entry and Exit Period Overlapping ................... 217
4Gb: x4, x8, x16 DDR3L SDRAM
Description
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 8Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
List of Tables
Table 1: Key Timing Parameters ....................................................................................................................... 1
Table 2: Addressing ......................................................................................................................................... 2
Table 3: 78-Ball FBGA – x4, x8 Ball Descriptions .............................................................................................. 19
Table 4: 96-Ball FBGA – x16 Ball Descriptions ................................................................................................. 21
Table 5: Absolute Maximum Ratings .............................................................................................................. 29
Table 6: DDR3L Input/Output Capacitance .................................................................................................... 30
Table 7: Thermal Characteristics .................................................................................................................... 31
Table 8: Thermal Impedance ......................................................................................................................... 32
Table 9: Timing Parameters Used for IDD Measurements – Clock Units ............................................................ 33
Table 10: IDD0 Measurement Loop .................................................................................................................. 34
Table 11: IDD1 Measurement Loop .................................................................................................................. 35
Table 12: IDD Measurement Conditions for Power-Down Currents ................................................................... 36
Table 13: IDD2N and IDD3N Measurement Loop ................................................................................................ 37
Table 14: IDD2NT Measurement Loop .............................................................................................................. 37
Table 15: IDD4R Measurement Loop ................................................................................................................ 38
Table 16: IDD4W Measurement Loop ............................................................................................................... 39
Table 17: IDD5B Measurement Loop ................................................................................................................ 40
Table 18: IDD Measurement Conditions for IDD6, IDD6ET, and IDD8 .................................................................... 41
Table 19: IDD7 Measurement Loop .................................................................................................................. 42
Table 20: IDD Maximum Limits Die Rev. E for 1.35/1.5V Operation ................................................................... 44
Table 21: IDD Maximum Limits Die Rev. N for 1.35V/1.5V Operation ................................................................ 45
Table 22: IDD Maximum Limits Die Rev. P for 1.35V/1.5V Operation ................................................................. 47
Table 23: DDR3L 1.35V DC Electrical Characteristics and Operating Conditions .............................................. 49
Table 24: DDR3L 1.35V DC Electrical Characteristics and Input Conditions ..................................................... 50
Table 25: DDR3L 1.35V Input Switching Conditions – Command and Address ................................................. 51
Table 26: DDR3L 1.35V Differential Input Operating Conditions (CK, CK# and DQS, DQS#) .............................. 52
Table 27: DDR3L Control and Address Pins ..................................................................................................... 54
Table 28: DDR3L 1.35V Clock, Data, Strobe, and Mask Pins ............................................................................. 54
Table 29: DDR3L 1.35V – Minimum Required Time tDVAC for CK/CK#, DQS/DQS# Differential for AC Ringback ... 56
Table 30: Single-Ended Input Slew Rate Definition .......................................................................................... 57
Table 31: DDR3L 1.35V Differential Input Slew Rate Definition ........................................................................ 59
Table 32: On-Die Termination DC Electrical Characteristics ............................................................................ 60
Table 33: 1.35V RTT Effective Impedance ........................................................................................................ 61
Table 34: ODT Sensitivity Definition .............................................................................................................. 62
Table 35: ODT Temperature and Voltage Sensitivity ........................................................................................ 62
Table 36: ODT Timing Definitions .................................................................................................................. 63
Table 37: DDR3L(1.35V) Reference Settings for ODT Timing Measurements .................................................... 63
Table 38: DDR3L 34 Ohm Driver Impedance Characteristics ........................................................................... 67
Table 39: DDR3L 34 Ohm Driver Pull-Up and Pull-Down Impedance Calculations ........................................... 68
Table 40: DDR3L 34 Ohm Driver IOH/IOL Characteristics: VDD = VDDQ = DDR3L@1.35V ..................................... 68
Table 41: DDR3L 34 Ohm Driver IOH/IOL Characteristics: VDD = VDDQ = DDR3L@1.45V ..................................... 68
Table 42: DDR3L 34 Ohm Driver IOH/IOL Characteristics: VDD = VDDQ = DDR3L@1.283 ..................................... 69
Table 43: DDR3L 34 Ohm Output Driver Sensitivity Definition ........................................................................ 69
Table 44: DDR3L 34 Ohm Output Driver Voltage and Temperature Sensitivity .................................................. 69
Table 45: DDR3L 40 Ohm Driver Impedance Characteristics ........................................................................... 70
Table 46: DDR3L 40 Ohm Output Driver Sensitivity Definition ........................................................................ 70
Table 47: 40 Ohm Output Driver Voltage and Temperature Sensitivity .............................................................. 71
Table 48: DDR3L Single-Ended Output Driver Characteristics ......................................................................... 72
Table 49: DDR3L Differential Output Driver Characteristics ............................................................................ 73
Table 50: DDR3L Differential Output Driver Characteristics VOX(AC) ................................................................. 74
4Gb: x4, x8, x16 DDR3L SDRAM
Description
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 9Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Table 51: Single-Ended Output Slew Rate Definition ....................................................................................... 75
Table 52: Differential Output Slew Rate Definition .......................................................................................... 77
Table 53: DDR3L-1066 Speed Bins .................................................................................................................. 78
Table 54: DDR3L-1333 Speed Bins .................................................................................................................. 79
Table 55: DDR3L-1600 Speed Bins .................................................................................................................. 80
Table 56: DDR3L-1866 Speed Bins .................................................................................................................. 81
Table 57: DDR3L-2133 Speed Bins .................................................................................................................. 82
Table 58: Electrical Characteristics and AC Operating Conditions .................................................................... 83
Table 59: Electrical Characteristics and AC Operating Conditions for Speed Extensions .................................... 93
Table 60: DDR3L Command and Address Setup and Hold Values 1 V/ns Referenced – AC/DC-Based ............... 103
Table 61: DDR3L-800/1066 Derating Values tIS/tIH – AC160/DC90-Based ....................................................... 104
Table 62: DDR3L-800/1066/1333/1600 Derating Values for tIS/tIH – AC135/DC90-Based ................................ 104
Table 63: DDR3L-1866/2133 Derating Values for tIS/tIH – AC125/DC90-Based ................................................ 104
Table 64: DDR3L Minimum Required Time tVAC Above VIH(AC) (Below VIL[AC]) for Valid ADD/CMD Transition . 105
Table 65: DDR3L Data Setup and Hold Values at 1 V/ns (DQS, DQS# at 2 V/ns) – AC/DC-Based ....................... 110
Table 66: DDR3L Derating Values for tDS/tDH – AC160/DC90-Based .............................................................. 111
Table 67: DDR3L Derating Values for tDS/tDH – AC135/DC90-Based .............................................................. 111
Table 68: DDR3L Derating Values for tDS/tDH – AC130/DC90-Based at 2V/ns ................................................. 112
Table 69: DDR3L Minimum Required Time tVAC Above VIH(AC) (Below VIL(AC)) for Valid DQ Transition ............. 113
Table 70: Truth Table – Command ................................................................................................................. 118
Table 71: Truth Table – CKE .......................................................................................................................... 120
Table 72: READ Command Summary ............................................................................................................ 122
Table 73: WRITE Command Summary .......................................................................................................... 122
Table 74: READ Electrical Characteristics, DLL Disable Mode ......................................................................... 128
Table 75: Write Leveling Matrix ..................................................................................................................... 132
Table 76: Burst Order .................................................................................................................................... 143
Table 77: MPR Functional Description of MR3 Bits ........................................................................................ 153
Table 78: MPR Readouts and Burst Order Bit Mapping ................................................................................... 154
Table 79: Self Refresh Temperature and Auto Self Refresh Description ............................................................ 186
Table 80: Self Refresh Mode Summary ........................................................................................................... 186
Table 81: Command to Power-Down Entry Parameters .................................................................................. 187
Table 82: Power-Down Modes ....................................................................................................................... 188
Table 83: Truth Table – ODT (Nominal) ......................................................................................................... 198
Table 84: ODT Parameters ............................................................................................................................ 198
Table 85: Write Leveling with Dynamic ODT Special Case .............................................................................. 199
Table 86: Dynamic ODT Specific Parameters ................................................................................................. 200
Table 87: Mode Registers for RTT,nom ............................................................................................................. 200
Table 88: Mode Registers for RTT(WR) ............................................................................................................. 201
Table 89: Timing Diagrams for Dynamic ODT ................................................................................................ 201
Table 90: Synchronous ODT Parameters ........................................................................................................ 206
Table 91: Asynchronous ODT Timing Parameters for All Speed Bins ............................................................... 211
Table 92: ODT Parameters for Power-Down (DLL Off) Entry and Exit Transition Period ................................... 213
4Gb: x4, x8, x16 DDR3L SDRAM
Description
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Important Notes and Warnings
Micron Technology, Inc. ("Micron") reserves the right to make changes to information published in this document,
including without limitation specifications and product descriptions. This document supersedes and replaces all
information supplied prior to the publication hereof. You may not rely on any information set forth in this docu-
ment if you obtain the product described herein from any unauthorized distributor or other source not authorized
by Micron.
Automotive Applications. Products are not designed or intended for use in automotive applications unless specifi-
cally designated by Micron as automotive-grade by their respective data sheets. Distributor and customer/distrib-
utor shall assume the sole risk and liability for and shall indemnify and hold Micron harmless against all claims,
costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of
product liability, personal injury, death, or property damage resulting directly or indirectly from any use of non-
automotive-grade products in automotive applications. Customer/distributor shall ensure that the terms and con-
ditions of sale between customer/distributor and any customer of distributor/customer (1) state that Micron
products are not designed or intended for use in automotive applications unless specifically designated by Micron
as automotive-grade by their respective data sheets and (2) require such customer of distributor/customer to in-
demnify and hold Micron harmless against all claims, costs, damages, and expenses and reasonable attorneys'
fees arising out of, directly or indirectly, any claim of product liability, personal injury, death, or property damage
resulting from any use of non-automotive-grade products in automotive applications.
Critical Applications. Products are not authorized for use in applications in which failure of the Micron compo-
nent could result, directly or indirectly in death, personal injury, or severe property or environmental damage
("Critical Applications"). Customer must protect against death, personal injury, and severe property and environ-
mental damage by incorporating safety design measures into customer's applications to ensure that failure of the
Micron component will not result in such harms. Should customer or distributor purchase, use, or sell any Micron
component for any critical application, customer and distributor shall indemnify and hold harmless Micron and
its subsidiaries, subcontractors, and affiliates and the directors, officers, and employees of each against all claims,
costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of
product liability, personal injury, or death arising in any way out of such critical application, whether or not Mi-
cron or its subsidiaries, subcontractors, or affiliates were negligent in the design, manufacture, or warning of the
Micron product.
Customer Responsibility. Customers are responsible for the design, manufacture, and operation of their systems,
applications, and products using Micron products. ALL SEMICONDUCTOR PRODUCTS HAVE INHERENT FAIL-
URE RATES AND LIMITED USEFUL LIVES. IT IS THE CUSTOMER'S SOLE RESPONSIBILITY TO DETERMINE
WHETHER THE MICRON PRODUCT IS SUITABLE AND FIT FOR THE CUSTOMER'S SYSTEM, APPLICATION, OR
PRODUCT. Customers must ensure that adequate design, manufacturing, and operating safeguards are included
in customer's applications and products to eliminate the risk that personal injury, death, or severe property or en-
vironmental damages will result from failure of any semiconductor component.
Limited Warranty. In no event shall Micron be liable for any indirect, incidental, punitive, special or consequential
damages (including without limitation lost profits, lost savings, business interruption, costs related to the removal
or replacement of any products or rework charges) whether or not such damages are based on tort, warranty,
breach of contract or other legal theory, unless explicitly stated in a written agreement executed by Micron's duly
authorized representative.
4Gb: x4, x8, x16 DDR3L SDRAM
Important Notes and Warnings
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
State Diagram
Figure 2: Simplified State Diagram
SRX = Self refresh exit
WRITE = WR, WRS4, WRS8
WRITE AP = WRAP, WRAPS4, WRAPS8
ZQCL = ZQ LONG CALIBRATION
ZQCS = ZQ SHORT CALIBRATION
Bank
active
ReadingWriting
Activating
Refreshing
Self
refresh
Idle
Active
power-
down
ZQ
calibration
From any
state
Power
applied Reset
procedure
Power
on
Initial-
ization
MRS, MPR,
write
leveling
Precharge
power-
down
Writing Reading
Automatic
sequence
Command
sequence
Precharging
READ
READ READ
READ AP
READ AP
READ AP
PRE, PREA
PRE, PREA PRE, PREA
WRITE
WRITE
CKE L CKE L
CKE L
WRITE
WRITE AP
WRITE AP
WRITE AP
PDE
PDE
PDX
PDX
SRX
SRE
REF
MRS
ACT
RESET
ZQCL
ZQCL/ZQCS
ACT = ACTIVATE
MPR = Multipurpose register
MRS = Mode register set
PDE = Power-down entry
PDX = Power-down exit
PRE = PRECHARGE
PREA = PRECHARGE ALL
READ = RD, RDS4, RDS8
READ AP = RDAP, RDAPS4, RDAPS8
REF = REFRESH
RESET = START RESET PROCEDURE
SRE = Self refresh entry
4Gb: x4, x8, x16 DDR3L SDRAM
State Diagram
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Functional Description
DDR3 SDRAM uses a double data rate architecture to achieve high-speed operation.
The double data rate architecture is an 8n-prefetch architecture with an interface de-
signed to transfer two data words per clock cycle at the I/O pins. A single read or write
operation for the DDR3 SDRAM effectively consists of a single 8n-bit-wide, four-clock-
cycle data transfer at the internal DRAM core and eight corresponding n-bit-wide, one-
half-clock-cycle data transfers at the I/O pins.
The differential data strobe (DQS, DQS#) is transmitted externally, along with data, for
use in data capture at the DDR3 SDRAM input receiver. DQS is center-aligned with data
for WRITEs. The read data is transmitted by the DDR3 SDRAM and edge-aligned to the
data strobes.
The DDR3 SDRAM operates from a differential clock (CK and CK#). The crossing of CK
going HIGH and CK# going LOW is referred to as the positive edge of CK. Control, com-
mand, and address signals are registered at every positive edge of CK. Input data is reg-
istered on the first rising edge of DQS after the WRITE preamble, and output data is ref-
erenced on the first rising edge of DQS after the READ preamble.
Read and write accesses to the DDR3 SDRAM are burst-oriented. Accesses start at a se-
lected location and continue for a programmed number of locations in a programmed
sequence. Accesses begin with the registration of an ACTIVATE command, which is then
followed by a READ or WRITE command. The address bits registered coincident with
the ACTIVATE command are used to select the bank and row to be accessed. The ad-
dress bits registered coincident with the READ or WRITE commands are used to select
the bank and the starting column location for the burst access.
The device uses a READ and WRITE BL8 and BC4. An auto precharge function may be
enabled to provide a self-timed row precharge that is initiated at the end of the burst
access.
As with standard DDR SDRAM, the pipelined, multibank architecture of DDR3 SDRAM
allows for concurrent operation, thereby providing high bandwidth by hiding row pre-
charge and activation time.
A self refresh mode is provided, along with a power-saving, power-down mode.
Industrial Temperature
The industrial temperature (IT) device requires that the case temperature not exceed
–40°C or 95°C. JEDEC specifications require the refresh rate to double when TC exceeds
85°C; this also requires use of the high-temperature self refresh option. Additionally,
ODT resistance and the input/output impedance must be derated when TC is < 0°C or
>95°C.
Automotive Temperature
The Automotive temperature (AT) device requires that the case temperature not exceed
–40°C or 105°C. Micron specification requires the refresh rate to 4X when TC exceeds
95°C; this also requires use of the high-temperature self refresh option. Additionally,
ODT resistance and the input/output impedance must be derated when TC is < 0°C or
>95°C.
4Gb: x4, x8, x16 DDR3L SDRAM
Functional Description
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
General Notes
• The functionality and the timing specifications discussed in this data sheet are for the
DLL enable mode of operation (normal operation).
• Throughout this data sheet, various figures and text refer to DQs as “DQ.” DQ is to be
interpreted as any and all DQ collectively, unless specifically stated otherwise.
• The terms “DQS” and “CK” found throughout this data sheet are to be interpreted as
DQS, DQS# and CK, CK# respectively, unless specifically stated otherwise.
• Complete functionality may be described throughout the document; any page or dia-
gram may have been simplified to convey a topic and may not be inclusive of all re-
quirements.
• Any specific requirement takes precedence over a general statement.
• Any functionality not specifically stated is considered undefined, illegal, and not sup-
ported, and can result in unknown operation.
• Row addressing is denoted as A[n:0]. For example, 1Gb: n = 12 (x16); 1Gb: n = 13 (x4,
x8); 2Gb: n = 13 (x16) and 2Gb: n = 14 (x4, x8); 4Gb: n = 14 (x16); and 4Gb: n = 15 (x4,
x8).
• Dynamic ODT has a special use case: when DDR3 devices are architected for use in a
single rank memory array, the ODT ball can be wired HIGH rather than routed. Refer
to the Dynamic ODT Special Use Case section.
• A x16 device's DQ bus is comprised of two bytes. If only one of the bytes needs to be
used, use the lower byte for data transfers and terminate the upper byte as noted:
– Connect UDQS to ground via 1kȍ* resistor.
– Connect UDQS# to VDD via 1kȍ* resistor.
– Connect UDM to VDD via 1kȍ* resistor.
– Connect DQ[15:8] individually to either VSS, VDD, or VREF via 1kȍ resistors,* or float
DQ[15:8].
*If ODT is used, 1kȍ resistor should be changed to 4x that of the selected ODT.
4Gb: x4, x8, x16 DDR3L SDRAM
Functional Description
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Functional Block Diagrams
DDR3 SDRAM is a high-speed, CMOS dynamic random access memory. It is internally
configured as an 8-bank DRAM.
Figure 3: 1 Gig x 4 Functional Block Diagram
Bank 5
Bank 6
Bank 7
Bank 4
Bank 7
Bank 4
Bank 5
Bank 6
16
Row-
address
MUX
Control
logic
Column-
address
counter/
latch
Mode registers
11
Command
decode
A[15:0]
BA[2:0]
16
Address
register
19
256
(x32)
8,192
I/O gating
DM mask logic
Column
decoder
Bank 0
memory
array
(65,536 x 256 x 32)
Bank 0
row-
address
latch
and
decoder
65,536
Sense amplifiers
Bank
control
logic
19
Bank 1
Bank 2
Bank 3
16
8
3
3
Refresh
counter
4
32
32
32
DQS, DQS#
Columns 0, 1, and 2
Columns 0, 1, and 2
ZQCL, ZQCS
To pull-up/pull-down
networks
READ
drivers DQ[3:0]
READ
FIFO
and
data
MUX
Data
4
3
Bank 1
Bank 2
Bank 3
DM
DM
CK, CK#
DQS, DQS#
ZQ CAL
CS#
ZQ
RZQ
CK, CK#
RAS#
WE#
CAS#
ODT
CKE
RESET#
CK, CK#
DLL
DQ[3:0]
(1 . . . 4)
(1, 2)
sw1 sw2
VDDQ/2
RTT,nom
R
TT(WR)
sw1 sw2
V
DDQ
/2
RTT,nom RTT(WR)
sw1 sw2
VDDQ/2
RTT,nom
R
TT(WR)
OTF
BC4 (burst chop)
BC4
Column 2
(select upper or
lower nibble for BC4)
Data
interface
WRITE
drivers
and
input
logic
ODT
control
VSSQ A12
OTF
BC4
4Gb: x4, x8, x16 DDR3L SDRAM
Functional Block Diagrams
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Figure 4: 512 Meg x 8 Functional Block Diagram
Bank 5
Bank 6
Bank 7
Bank 4
Bank 7
Bank 4
Bank 5
Bank 6
16
Row-
address
MUX
Control
logic
Column-
address
counter/
latch
Mode registers
10
Command
decode
A[15:0]
BA[2:0]
16
19
8,192
I/O gating
DM mask logic
Column
decoder
Bank 0
Memory
array
(65,536 x 128 x 64)
Bank 0
row-
address
latch
and
decoder
65,536
Sense amplifiers
Bank
control
logic
19
Bank 1
Bank 2
Bank 3
16
7
3
3
Refresh
counter
8
64
64
64
DQS, DQS#
Columns 0, 1, and 2
Columns 0, 1, and 2
ZQCL, ZQCS
To ODT/output drivers
Read
drivers DQ[7:0]
READ
FIFO
and
data
MUX
Data
8
3
Bank 1
Bank 2
Bank 3
DM/TDQS
(shared pin)
TDQS#
CK, CK#
DQS/DQS#
ZQ CAL
ZQ
RZQ
ODT
CKE
CK, CK#
RAS#
WE#
CAS#
CS#
RESET#
CK, CK#
DLL
DQ[7:0]
DQ8
(1 . . . 8)
(1, 2)
sw1 sw2
VDDQ/2
RTT(WR)
RTT,nom
sw1 sw2
V
DDQ
/2
RTT,nom RTT(WR)
sw1 sw2
VDDQ/2
RTT,nom RTT(WR)
BC4 (burst chop)
BC4
BC4
Write
drivers
and
input
logic
Data
interface
Column 2
(select upper or
lower nibble for BC4)
(128
x64)
ODT
control
Address
register
A12
V
SSQ
OTF
OTF
Figure 5: 256 Meg x 16 Functional Block Diagram
Bank 5
Bank 6
Bank 7
Bank 4
Bank 7
Bank 4
Bank 5
Bank 6
13
Row-
address
MUX
Control
logic
Column-
address
counter/
latch
Mode registers
10
Command
decode
A[14:0]
BA[2:0]
15
Address
register
18
(128
x128)
16,384
I/O gating
DM mask logic
Column
decoder
Bank 0
memory
array
(32,768 x 128 x 128)
Bank 0
row-
address
latch
and
decoder
32,768
Sense amplifiers
Bank
control
logic
18
Bank 1
Bank 2
Bank 3
15
7
3
3
Refresh
counter
16
128
128
128
LDQS, LDQS#, UDQS, UDQS#
Column 0, 1, and 2
Columns 0, 1, and 2
ZQCL, ZQCS
To ODT/output drivers
BC4
READ
drivers DQ[15:0]
READ
FIFO
and
data
MUX
Data
16
BC4 (burst chop)
3
Bank 1
Bank 2
Bank 3
LDM/UDM
CK, CK#
LDQS, LDQS#
UDQS, UDQS#
ZQ CAL
ZQ
RZQ
ODT
CKE
CK, CK#
RAS#
WE#
CAS#
CS#
RESET#
CK, CK#
DLL
DQ[15:0]
(1 . . . 16)
(1 . . . 4)
(1, 2)
sw1 sw2
VDDQ/2
RTT,nom RTT(WR)
BC4
sw1 sw2
VDDQ/2
RTT,nom RTT(WR)
sw1 sw2
VDDQ/2
RTT,nom RTT(WR)
Column 2
(select upper or
lower nibble for BC4)
Data
interface
WRITE
drivers
and
input
logic
ODT
control
V
SSQ
A12
OTF
OTF
4Gb: x4, x8, x16 DDR3L SDRAM
Functional Block Diagrams
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 16 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Ball Assignments and Descriptions
Figure 6: 78-Ball FBGA – x4, x8 (Top View)
1234 67895
VSS
VSS
VDDQ
VSSQ
VREFDQ
NC
ODT
NC
VSS
VDD
VSS
V
DD
VSS
VDD
VSSQ
DQ2
NF, DQ6
VDDQ
VSS
VDD
CS#
BA0
A3
A5
A7
RESET#
NC
DQ0
DQS
DQS#
NF, DQ4
RAS#
CAS#
WE#
BA2
A0
A2
A9
A13
NF, NF/TDQS#
DM, DM/TDQS
DQ1
VDD
NF, DQ7
CK
CK#
A10/AP
A15
A12/BC#
A1
A11
A14
VDD
VDDQ
VSSQ
VSSQ
VDDQ
NC
CKE
NC
VSS
VDD
VSS
VDD
VSS
VSS
VSSQ
DQ3
VSS
NF, DQ5
VSS
VDD
ZQ
VREFCA
BA1
A4
A6
A8
A
B
C
D
E
F
G
H
J
K
L
M
N
Notes: 1. Ball descriptions listed in Table 3 (page 19) are listed as “x4, x8” if unique; otherwise,
x4 and x8 are the same.
2. A comma separates the configuration; a slash defines a selectable function.
Example D7 = NF, NF/TDQS#. NF applies to the x4 configuration only. NF/TDQS# applies
to the x8 configuration only—selectable between NF or TDQS# via MRS (symbols are de-
fined in Table 3).
4Gb: x4, x8, x16 DDR3L SDRAM
Ball Assignments and Descriptions
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 17 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Figure 7: 96-Ball FBGA – x16 (Top View)
1234 67895
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
VDDQ
VSSQ
VDDQ
VSSQ
VSS
VDDQ
VSSQ
VREFDQ
NC
ODT
NC
VSS
VDD
VSS
VDD
VSS
DQ13
VDD
DQ11
VDDQ
VSSQ
DQ2
DQ6
VDDQ
VSS
VDD
CS#
BA0
A3
A5
A7
RESET#
DQ15
VSS
DQ9
UDM
DQ0
LDQS
LDQS#
DQ4
RAS#
CAS#
WE#
BA2
A0
A2
A9
A13
DQ12
UDQS#
UDQS
DQ8
LDM
DQ1
VDD
DQ7
CK
CK#
A10/AP
NC
A12/BC#
A1
A11
A14
VDDQ
DQ14
DQ10
VSSQ
VSSQ
DQ3
VSS
DQ5
VSS
VDD
ZQ
VREFCA
BA1
A4
A6
A8
VSS
VSSQ
VDDQ
VDD
VDDQ
VSSQ
VSSQ
VDDQ
NC
CKE
NC
VSS
VDD
VSS
VDD
VSS
Notes: 1. Ball descriptions listed in Table 4 (page 21) are listed as “x4, x8” if unique; otherwise,
x4 and x8 are the same.
2. A comma separates the configuration; a slash defines a selectable function.
Example D7 = NF, NF/TDQS#. NF applies to the x4 configuration only. NF/TDQS# applies
to the x8 configuration only—selectable between NF or TDQS# via MRS (symbols are de-
fined in Table 3).
4Gb: x4, x8, x16 DDR3L SDRAM
Ball Assignments and Descriptions
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 18 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Table 3: 78-Ball FBGA – x4, x8 Ball Descriptions
Symbol Type Description
A[15:13], A12/BC#,
A11, A10/AP, A[9:0]
Input Address inputs: Provide the row address for ACTIVATE commands, and the column
address and auto precharge bit (A10) for READ/WRITE commands, to select one
location out of the memory array in the respective bank. A10 sampled during a
PRECHARGE command determines whether the PRECHARGE applies to one bank
(A10 LOW, bank selected by BA[2:0]) or all banks (A10 HIGH). The address inputs also
provide the op-code during a LOAD MODE command. Address inputs are referenced
to VREFCA. A12/BC#: When enabled in the mode register (MR), A12 is sampled during
READ and WRITE commands to determine whether burst chop (on-the-fly) will be
performed (HIGH = BL8 or no burst chop, LOW = BC4). See Table 70 (page 118).
BA[2:0] Input Bank address inputs: BA[2:0] define the bank to which an ACTIVATE, READ,
WRITE, or PRECHARGE command is being applied. BA[2:0] define which mode
register (MR0, MR1, MR2, or MR3) is loaded during the LOAD MODE command.
BA[2:0] are referenced to VREFCA.
CK, CK# Input Clock: CK and CK# are differential clock inputs. All control and address input signals
are sampled on the crossing of the positive edge of CK and the negative edge of
CK#. Output data strobe (DQS, DQS#) is referenced to the crossings of CK and CK#.
CKE Input Clock enable: CKE enables (registered HIGH) and disables (registered LOW)
internal circuitry and clocks on the DRAM. The specific circuitry that is enabled/
disabled is dependent upon the DDR3 SDRAM configuration and operating mode.
Taking CKE LOW provides PRECHARGE POWER-DOWN and SELF REFRESH operations
(all banks idle), or active power-down (row active in any bank). CKE is synchronous
for power-down entry and exit and for self refresh entry. CKE is asynchronous for
self refresh exit. Input buffers (excluding CK, CK#, CKE, RESET#, and ODT) are
disabled during POWER-DOWN. Input buffers (excluding CKE and RESET#) are disa-
bled during SELF REFRESH. CKE is referenced to VREFCA.
CS# Input Chip select: CS# enables (registered LOW) and disables (registered HIGH) the
command decoder. All commands are masked when CS# is registered HIGH. CS#
provides for external rank selection on systems with multiple ranks. CS# is considered
part of the command code. CS# is referenced to VREFCA.
DM Input Input data mask: DM is an input mask signal for write data. Input data is masked
when DM is sampled HIGH along with the input data during a write access.
Although the DM ball is input-only, the DM loading is designed to match that of the
DQ and DQS balls. DM is referenced to VREFDQ. DM has an optional use as TDQS on
the x8.
ODT Input On-die termination: ODT enables (registered HIGH) and disables (registered LOW)
termination resistance internal to the DDR3 SDRAM. When enabled in normal
operation, ODT is only applied to each of the following balls: DQ[7:0], DQS, DQS#,
and DM for the x8; DQ[3:0], DQS, DQS#, and DM for the x4. The ODT input is
ignored if disabled via the LOAD MODE command. ODT is referenced to VREFCA.
RAS#, CAS#, WE# Input Command inputs: RAS#, CAS#, and WE# (along with CS#) define the command
being entered and are referenced to VREFCA.
RESET# Input Reset: RESET# is an active LOW CMOS input referenced to VSS. The RESET# input re-
ceiver is a CMOS input defined as a rail-to-rail signal with DC HIGH ุ 0.8 × VDD and
DC LOW ื 0.2 × VDDQ. RESET# assertion and desertion are asynchronous.
4Gb: x4, x8, x16 DDR3L SDRAM
Ball Assignments and Descriptions
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 19 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.
Table 3: 78-Ball FBGA – x4, x8 Ball Descriptions (Continued)
Symbol Type Description
DQ[3:0] I/O Data input/output: Bidirectional data bus for the x4 configuration. DQ[3:0] are
referenced to VREFDQ.
DQ[7:0] I/O Data input/output: Bidirectional data bus for the x8 configuration. DQ[7:0] are
referenced to VREFDQ.
DQS, DQS# I/O Data strobe: Output with read data. Edge-aligned with read data. Input with write
data. Center-aligned to write data.
TDQS, TDQS# Output Termination data strobe: Applies to the x8 configuration only. When TDQS is
enabled, DM is disabled, and the TDQS and TDQS# balls provide termination
resistance.
VDD Supply Power supply: 1.5V ±0.075V.
VDDQ Supply DQ power supply: 1.5V ±0.075V. Isolated on the device for improved noise immuni-
ty.
VREFCA Supply Reference voltage for control, command, and address: VREFCA must be
maintained at all times (including self refresh) for proper device operation.
VREFDQ Supply Reference voltage for data: VREFDQ must be maintained at all times (excluding self
refresh) for proper device operation.
VSS Supply Ground.
VSSQ Supply DQ ground: Isolated on the device for improved noise immunity.
ZQ Reference External reference ball for output drive calibration: This ball is tied to an
external 240˖ resistor (RZQ), which is tied to VSSQ.
NC – No connect: These balls should be left unconnected (the ball has no connection to
the DRAM or to other balls).
NF – No function: When configured as a x4 device, these balls are NF. When configured
as a x8 device, these balls are defined as TDQS#, DQ[7:4].
4Gb: x4, x8, x16 DDR3L SDRAM
Ball Assignments and Descriptions
09005aef85af8fa8
4Gb_DDR3L.pdf - Rev. R 09/18 EN 20 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2017 Micron Technology, Inc. All rights reserved.