Freescale Semiconductor Data Sheet: Technical Data Document Number: IMX28CEC Rev. 3, 07/2012 i.MX28 i.MX28 Applications Processors for Consumer Products Package Information Plastic package Case MAPBGA-289, 14 x 14 mm, 0.8 mm pitch Silicon Version 1.2 Ordering Information See Table 1 on page 3 for ordering information. 1 Introduction The i.MX28 is a low-power, high-performance applications processor optimized for the general embedded industrial and consumer markets. The core of the i.MX28 is Freescale's fast, power-efficient implementation of the ARM926EJ-STM core, with speeds of up to 454 MHz. The device is suitable for a wide range of applications, including the following: * Human-machine interface (HMI) panels: industrial, home * Industrial drive, PLC, I/O control display, factory robotics display, graphical remote controls * Handheld scanners and printers * Patient-monitoring, portable medical devices * Smart energy meters, energy gateways * Media phones, media gateways The integrated power management unit (PMU) on the i.MX28 is composed of a triple output DC-DC switching converter and multiple linear regulators. These provide power sequencing for the device and its I/O peripherals (c) 2012 Freescale Semiconductor, Inc. All rights reserved. Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1. Device Features . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2. Ordering Information and Functional Part Differences 3 1.3. Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.1. Special Signal Considerations . . . . . . . . . . . . . . . 11 3. Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 11 3.1. i.MX28 Device-Level Conditions . . . . . . . . . . . . . . 11 3.2. Thermal Characteristics . . . . . . . . . . . . . . . . . . . . 18 3.3. I/O DC Parameters . . . . . . . . . . . . . . . . . . . . . . . . 19 3.4. I/O AC Timing and Parameters . . . . . . . . . . . . . . 23 3.5. Module Timing and Electrical Parameters . . . . . . 27 4. Package Information and Contact Assignments . . . . . . 59 4.1. Case MAPBGA-289, 14 x 14 mm, 0.8 mm Pitch . 59 4.2. Ground, Power, Sense, and Reference Contact Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 4.3. Signal Contact Assignments . . . . . . . . . . . . . . . . 61 4.4. i.MX280 Ball Map . . . . . . . . . . . . . . . . . . . . . . . . . 63 4.5. i.MX283 Ball Map . . . . . . . . . . . . . . . . . . . . . . . . . 65 4.6. i.MX286 Ball Map . . . . . . . . . . . . . . . . . . . . . . . . . 67 4.7. i.MX287 Ball Map . . . . . . . . . . . . . . . . . . . . . . . . . 69 5. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Introduction such as memories and SD cards, as well as provide battery charging capability for Li-Ion batteries. The i.MX28 processor includes an additional 128-Kbyte on-chip SRAM to make the device ideal for eliminating external RAM in applications with small footprint RTOS. The i.MX28 supports connections to various types of external memories, such as mobile DDR, DDR2 and LV-DDR2, SLC and MLC NAND Flash. The i.MX28 can be connected to a variety of external devices such as high-speed USB2.0 OTG, CAN, 10/100 Ethernet, and SD/SDIO/MMC. 1.1 Device Features The following lists the features of the i.MX28: * ARM926EJ-S CPU running at 454 MHz: -- 16-Kbyte instruction cache and 32-Kbyte data cache -- ARM embedded trace macrocell (CoreSightTM ETM9TM) -- Parallel JTAG interface * 128 KBytes of integrated low-power on-chip SRAM * 128 KBytes of integrated mask-programmable on-chip ROM * 1280 bits of on-chip one-time-programmable (OCOTP) ROM * 16-bit mobile DDR (mDDR) (1.8 V), DDR2 (1.8 V) and LV-DDR2 (1.5 V), up to 205 MHz DDR clock frequency with voltage overdrive * Support for up to eight NAND Flash memory devices with up to 20-bit BCH ECC * Four synchronous serial ports (SSP) for SDIO/MMC/MS/SPI: SSP0, SSP1, SSP2, and SSP3. SSP0 and SSP1 can support three modes,1-bit, 4-bit, and 8-bit, whereas SSP2 and SSP3 can support only 1-bit and 4-bit modes. * 10/100-Mbps Ethernet MAC compatible with IEEE Std 802.3TM: -- Single 10/100 Ethernet with GMII/RMII or Dual 10/100 Ethernet with RMII interface -- Supporting IEEE Std 1588TM-compatible hardware timestamp -- Supporting 50-MHz/25-MHz clock output for external Ethernet PHY * Two 2.0B protocol-compatible Controller Area Network (CAN) interfaces * One USB2.0 OTG device/host controller and PHY * One USB2.0 host controller and PHY * LCD controller, up to 24-bit RGB (DOTCK) modes and 24-bit system-mode * Pixel-processing pipeline (PXP) supports full path from color-space conversion, scaling, alpha-blending to rotation without intermediate memory access. * SPDIF transmitter * Dual serial audio interface (SAIF) to support full-duplex transmit and receive operations; each SAIF supports three stereo pairs * Five application Universal Asynchronous Receiver-Transmitters (UARTs), up to 3.25 Mbps with hardware flow control i.MX28 Applications Processors for Consumer Products, Rev. 3 2 Freescale Semiconductor Introduction * * * * * * * * * * * * * 1.2 One debug UART operating at up to 115 Kb/s using programmed I/O Two I2C master/slave interfaces, up to 400 kbps Four 32-bit timers and a rotary decoder Eight Pulse Width Modulators (PWMs) Real-time clock (RTC) GPIO with interrupt capability Power Management Unit (PMU) supports a triple output DC-DC switching converter, multiple linear regulators, battery charger, and detector. 16-channel Low-Resolution A/D Converter (LRADC). There are 16 physical channels but they can only be mapped to 8 virtual channels at a time. Single channel High Speed A/D Converter (HSADC), up to 2 Msps data rate 4/5-wire touchscreen controller Up to 8X8 keypad matrix with button-detect circuit Security features: -- Read-only unique ID for Digital Rights Management (DRM) algorithms -- Secure boot using 128-bit AES hardware decryption -- SHA-1 and SHA256 hashing hardware -- High assurance boot (HAB4) Offered in 289-pin Ball Grid Array (BGA) Ordering Information and Functional Part Differences Table 1 provides the ordering information for the i.MX28. Table 1. Ordering Information Part Number Projected Temperature Range (C) Package MCIMX280DVM4B -20 to +70 14 x 14 mm, 0.8mm pitch, MAPBGA-289 MCIMX280CVM4B -40 to +85 14 x 14 mm, 0.8mm pitch, MAPBGA-289 MCIMX283DVM4B -20 to +70 14 x 14 mm, 0.8 mm pitch, MAPBGA-289 MCIMX283CVM4B -40 to +85 14 x 14 mm, 0.8 mm pitch, MAPBGA-289 MCIMX286DVM4B -20 to +70 14 x 14 mm, 0.8 mm pitch, MAPBGA-289 MCIMX286CVM4B -40 to +85 14 x 14 mm, 0.8 mm pitch, MAPBGA-289 MCIMX287CVM4B -40 to +85 14 x 14 mm, 0.8 mm pitch, MAPBGA-289 i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 3 Introduction Table 2 provides the functional differences between the i.MX280, i.MX283, i.MX286, and i.MX287. Table 2. i.MX28 Functional Differences Function i.MX280 i.MX283 i.MX286 i.MX287 Application UART x5 x5 x5 x5 Debug UART x1 x1 x1 x1 CAN -- -- x2 x2 Ethernet x1 x1 x1 x2 High-speed ADC x1 x1 x1 x1 L2 Switch -- -- -- Yes LCD Interface -- Yes Yes Yes LRADC1 x8 x8 x8 x8 PWM x8 x8 x8 x8 S/PDIF Tx -- -- Yes Yes SD/SDIO/MMC2 x4 x4 x4 x4 Security Yes Yes Yes Yes SPI x4 x4 x4 x4 Touch Screen -- Yes Yes Yes OTG HS with HS PHY x1 OTG HS with HS PHY x1 OTG HS with HS PHY x1 OTG HS with HS PHY x1 HS Host with HS PHY x1 HS Host with HS PHY x1 HS Host with HS PHY x1 HS Host with HS PHY x1 USB 2.0 1 2 There are 16 physical channels but they can only be mapped to 8 virtual channels at a time. For SD/SDIO/MMC, four synchronous serial ports (SSP) are available: SSP0, SSP1, SSP2, and SSP3. SSP0 and SSP1 can support three modes,1-bit, 4-bit, and 8-bit, whereas SSP2 and SSP3 can support only 1-bit and 4-bit modes. i.MX28 Applications Processors for Consumer Products, Rev. 3 4 Freescale Semiconductor Introduction 1.3 Block Diagram Figure 1 shows the simplified interface block diagram. Figure 1. i.MX28 Simplified Interface Block Diagram i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 5 Features 2 Features Table 3 shows the device functions. Table 3. i.MX28 Functions Function External Memory Interface (EMI) (1.5 V LV-DDR2, 1.8 V DDR2, 1.8 V LP-DDR1) BGA289 Yes General-Purpose Media Interface (GPMI): * NAND data width * Number of external NANDs supported 8-bit 4 dedicated / 8 with muxing Pulse Width Modulator (PWM) 5 dedicated / 8 with muxing Application UART (AUART): Interfaces supported 4 dedicated / 5 with muxing Synchronous Serial Port (SSP): Supported through dedicated pins 3 dedicated / 4 with muxing I2C 1 dedicated / 2 with muxing SPDIF 1 SAIF 2 FlexCAN 2 LCD interface 24 bits High-speed ADC Yes LRADC (touchscreen, keypad...) Yes Ethernet MAC and switch Up to 2 MACs with switch Universal Serial Bus (USB) 2 i.MX28 Applications Processors for Consumer Products, Rev. 3 6 Freescale Semiconductor Features Table 4 describes the digital and analog modules of the device. Table 4. i.MX28 Digital and Analog Modules Block Mnemonic Block Name Subsystem Brief Description APBHDMA AHB to APBH System control The AHB to APBH bridge with DMA includes the AHB-to-APB PIO bridge for memory-mapped I/O to the APB devices, as well a central DMA facility for Bridge with devices on this bus. The bridge provides a peripheral attachment bus running DMA on the AHB's HCLK. (The `H' in APBH denotes that the APBH is synchronous to HCLK, as compared to APBX, which runs on the crystal-derived XCLK.) The DMA controller transfers read and write data to and from each peripheral on APBH bridge. APBXDMA AHB to APBX System control The AHB-to-APBX bridge includes the AHB-to-APB PIO bridge for memory-mapped I/O to the APB devices, as well a central DMA facility for Bridge with devices on this bus. The AHB-to-APBX bridge provides a peripheral DMA attachment bus running on the AHB's XCLK. (The `X' in APBX denotes that the APBX runs on a crystal-derived clock, as compared to APBH, which is synchronous to HCLK.) The DMA controller transfers read and write data to and from each peripheral on APBX bridge. ARM9 or ARM926 ARM926EJ-S ARM(R) CPU AUART(5) Application UART interface Connectivity peripherals Each of the UART modules supports the following serial data transmit/receive protocols and configurations: * 7- or 8-bit data words, one or two stop bits, programmable parity (even, odd, or none) * Programmable baud rates up to 3.25 MHz. This is a higher maximum baud rate than the 1.875 MHz specified by the TIA/EIA-232-F standard and previous Freescale UART modules. 16-byte FIFO on Tx and 16-byte FIFO on Rx supporting auto-baud detection BCH Bit-correcting ECC accelerator Connectivity peripherals The Bose, Ray-Chaudhuri, Hocquenghem (BCH) Encoder and Decoder module is capable of correcting from 2 to 20 single bit errors within a block of data no larger than about 900 bytes (512 bytes is typical) in applications such as protecting data and resources stored on modern NAND Flash devices. BSI Boundary Connectivity Scan Interface peripherals The boundary scan interface is provided to enable board level testing. There are five pins on the device which is used to implement the IEEE Std 1149.1TM boundary scan protocol. CLKCTRL Clock control module Clocks The clock control module, or CLKCTRL, generates the clock domains for all components in the i.MX28 system. The crystal clock or PLL clock are the two fundamental sources used to produce most of the clock domains. For lower performance and reduced power consumption, the crystal clock is selected. The PLL is selected for higher performance requirements but requires increased power consumption. In most cases, when the PLL is used as the source, a Phase Fractional Divider (PFD) can be programmed to reduce the PLL clock frequency by up to a factor of 2. DCP Data co-processor Security This module provides support for general encryption and hashing functions typically used for security functions. Because its basic job is moving data from memory to memory, it also incorporates a memory-copy (memcopy) function for both debugging and as a more efficient method of copying data between memory blocks than the DMA-based approach. The ARM926 Platform consists of the ARM926EJ-STM core and the ETM real-time debug modules. It contains the 16-Kbyte L1 instruction cache, 32-Kbyte L1 data cache, 128-Kbyte ROM and 128-Kbyte RAM. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 7 Features Table 4. i.MX28 Digital and Analog Modules (continued) Block Mnemonic Block Name Subsystem Brief Description DFLPT System control The DFLPT provides a unique method of implementing the ARM MMU Default first-level page table (L1PT) using a hardware-based approach. first-level page table DIGCTL Digital control System control The digital control module includes sections for controlling the SRAM, the performance monitors, high-entropy pseudo-random number seed, and on-chip free-running microseconds counter, and other chip control functions. RAM DUART Debug UART Connectivity peripherals The Debug UART performs the following data conversions: * Serial-to-parallel conversion on data received from a peripheral device * Parallel-to-serial conversion on data transmitted to the peripheral device External memory interface Connectivity peripherals The i.MX28 supports off-chip DRAM storage through the EMI controller, which is connected to the four internal AHB/AXI busses. The EMI supports multiple external memory types, including: * 1.8-V Mobile DDR1 (LP-DDR1) * Standard 1.8-V DDR2 * Low Voltage 1.5-V DDR2 (LV-DDR2) Ethernet MAC Connectivity Controller peripherals Ethernet MAC controller connected to the uDMA (unified DMA). Supports 10/100 Mbps with TCP/UDP/IP Acceleration and IEEE 1588 Functions; also supports RMII or MII connectivity. EMI ENET FlexCAN(2) Controller area network module Connectivity peripherals The Controller Area Network (CAN) protocol is a message based protocol used for serial data. It was designed specifically for automotive but is also used in industrial control and medical applications. The serial data bus runs at 1 Mbps. GPMI General-purpose media interface Connectivity peripherals The General-Purpose Media Interface (GPMI) controller is a flexible NAND Flash controller with 8-bit data width, up to 50-MBps I/O speed and individual chip select and DMA channels for up to 8 NAND devices. It also provides a interface to 20-bit BCH for ECC. HSADC High-speed ADC Connectivity peripherals The high-speed ADC block is designed to sample an analog input with 12-bit resolution and a sample rate of up to 2 Msps. The output of the HSADC block can be moved to the external memory through APBH-DMA. A typical user case of the HSADC is to work with the PWM block to drive an external linear image scanner sensor. I2C(2) I2C module Connectivity peripherals The I2C is a standard two-wire serial interface used to connect the chip with peripherals or host controllers. The I2C operates up to 400 kbps in either I2C master or I2C slave mode. Each I2C has a dedicated DMA channel and can also controlled by CPU in PIO or PIO queue modes. It supports both 7-bit and 10-bit device address in master mode, and has programmable 7-bit address in slave mode. ICOLL Interrupt Collector System control The ARM9 CPU core has two interrupt input lines, IRQ and FIQ. The interrupt collector (ICOLL) can steer any of 128 interrupt sources to either the FIQ or IRQ line of the ARM9 CPU. L2 Switch 3-Port L2 Switch Network Control Programmable 3-Port Ethernet Switch with QOS i.MX28 Applications Processors for Consumer Products, Rev. 3 8 Freescale Semiconductor Features Table 4. i.MX28 Digital and Analog Modules (continued) Block Mnemonic Block Name Subsystem Brief Description LCDIF LCD Interface Multimedia peripherals The LCDIF provides display data for external LCD panels from simple text-only displays to WVGA, 16/18/24 bpp color TFT panels. The LCDIF supports all of these different interfaces by providing fully programmable functionality and sharing register space, FIFOs, and ALU resources at the same time. The LCDIF supports RGB (DOTCLK) modes as well as system mode including both VSYNC and WSYNC modes. LRADC Low resolution Connectivity ADC module peripherals The sixteen-channel 12-bit low-resolution ADC (LRADC) block is used for voltage measurement. Channels 0 - 6 measure the voltage on the seven application-dependent LRADC pins. The auxiliary channels can be used for a variety of uses, including a resistor-divider-based wired remote control, external temperature sensing, touch-screen, and other measurement functions. OCOTP Controller On-chip OTP controller Security The on-chip one-time-programmable (OCOTP) ROM serves the functions of hardware and software capability bits, Freescale operations and unique-ID, the customer-programmable cryptography key, and storage of various ROM configuration bits. PINCTRL Pin control and GPIO System control Used for general purpose input/output to external ICs. Each GPIO bank peripherals supports 32 bits of I/O. PMU PWM(8) PXP Power Power management management Unit (DC-DC) system The i.MX28 integrates a comprehensive power supply subsystem, including the following features: * One integrated DC-DC converter that supports Li-Ion battery. * Four linear regulators directly power the supply rails from 5-V. * Linear battery charger for Li-Ion cells. * Battery voltage and brownout detection monitoring for VDDD, VDDA, VDDIO, VDD4P2 and 5-V supplies. * Integrated current limiter from 5-V power source. * Reset controller. * System monitors for temperature and speed. * Generates USB-Host 5-V from Li-Ion battery (using PWM). * Support for on-the-fly transitioning between 5-V and battery power. * VDD4P2, a nominal 4.2-V supply, is available when the i.MX28 is connected to a 5-V source and allows the DCDC to run from a 5-V source with a depleted battery. * The 4.2-V regulated output also allows for programmable current limits: - Battery Charge current + DCDC input current < the 5-V current limit - DCDC input current (which ultimately provides current to the on-chip and off-chip loads) as the priority and battery charge current is automatically reduced if the 5-V current limit is reached Pulse width modulation There are eight PWM output controllers that can be used in place of GPIO pins. Applications include HSADC driving signals and LED & backlight brightness control. Independent output control of each phase allows 0, 1, or high-impedance to be independently selected for the active and inactive phases. Individual outputs can be run in lock step with guaranteed non-overlapping portions for differential drive applications. Connectivity peripherals Pixel Pipeline Multimedia The pixel pipeline (PXP) is used to perform alpha blending of graphic or video buffers with graphics data before sending to an LCD display. The PXP also supports image rotation for hand-held devices that require both portrait and landscape image support. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 9 Features Table 4. i.MX28 Digital and Analog Modules (continued) Block Mnemonic Block Name Subsystem Brief Description RTC Real-time clock, alarm, watchdog Clocks The real-time clock (RTC) and alarm share a one-second pulse time domain. The watchdog reset and millisecond counter run on a one-millisecond time domain. The RTC, alarm, and persistent bits reside in a special power domain (crystal domain) that remains powered up even when the rest of the chip is in its powered-down state. SAIF(2) Serial audio interface Connectivity peripherals SAIF provides a half-duplex serial port for communication with a variety of serial devices, including industry-standard codecs and DSPs. It supports a continuous range of sample rates from 8 kHz-192 kHz using a high-resolution fractional divider driven by the PLL. Samples are transferred to/from the FIFO through the APBX DMA interface, a FIFO service interrupt, or software polling. SPDIF SPDIF Connectivity peripherals The Sony-Philips Digital Interface Format (SPDIF) transmitter module transmits data according to the SPDIF digital audio interface standard (IEC-60958). SSP(4) Synchronous serial port Connectivity peripherals The synchronous serial port is a flexible interface for inter-IC and removable media control and communication. The SSP supports master operation of SPI, Texas Instruments SSI; 1-bit, 4-bit, and 8-bit SD/SDIO/MMC and 1-bit and 4-bit MS modes. The SPI mode has enhancements to support 1-bit legacy MMC cards. SPI master dual (2-bit) and quad (4-bit) mode reads are also supported. The SSP also supports slave operation for the SPI and SSI modes. The SSP has a dedicated DMA channel in the bridge and can also be controlled directly by the CPU through PIO registers. Each of the four SSP modules is independent of the other and can have separate SSPCLK frequencies. TIMROT Timers and Rotary Decoder Timer peripherals This module implements four timers and a rotary decoder. The timers and decoder can take their inputs from any of the pins defined for PWM, rotary encoders, or certain divisions from the 32-kHz clock input. Thus, the PWM pins can be inputs or outputs, depending on the application. USBOTG USBHOST High-speed USB on-the-go Connectivity peripherals The USB module provides high-performance USB On-The-Go (OTG) and host functionality (up to 480 Mbps), compliant with the USB 2.0 specification and the OTG supplement. The module has DMA capabilities for handling data transfer between internal buffers and system memory. When the OTG controller works in device mode, it can only work in FS or HS mode. Two USB2.0 PHYs are also integrated (one for the OTG port, another for the host port.) Integrated USB PHY Connectivity peripherals The integrated USB 2.0 PHY macrocells are capable of connecting to USB host/device systems at the USB low-speed (LS) rate of 1.5 Mbps, full-speed (FS) rate of 12 Mbps or at the USB 2.0 high-speed (HS) rate of 480 Mbps. The integrated PHYs provide a standard UTM interface. The USB_DP and USB_DN pins connect directly to a USB connector. USBPHY i.MX28 Applications Processors for Consumer Products, Rev. 3 10 Freescale Semiconductor Electrical Characteristics 2.1 Special Signal Considerations Special signal considerations are listed in Table 5. The package contact assignment is found in Section 4, "Package Information and Contact Assignments." Signal descriptions are provided in the reference manual. Table 5. Signal Considerations Signal Descriptions PSWITCH The pin is used for chip power on or recovery. VDDIO can be applied to PSWITCH through a 10 k resistor. This is necessary in order to enter the chip's firmware recovery. The on-chip circuitry prevents the actual voltage on the pin from exceeding acceptable levels. VDDXTAL This pin is an output of i.MX28. Should be coupled to ground with a 0.1 uF capacitor. User should not supply external power to this pin. BATTERY This pin should be connected to the battery with minimal resistance. It provides charging current to the battery. See the "Power Supply" section of the reference manual for details. DCDC_BATTERY This pin is an input of i.MX28 that provides supply to the DCDC converter. It should be connected to the battery with minimal resistance. See the "Power Supply" section of the reference manual for details. XTALI XTALO These analog pins are connected to an external 24 MHz crystal circuit. This crystal provides the clock source for on-chip PLLs. RTC_XTALO RTC_XTALI These analog pins are connected to an external 32.768/32.0 kHz crystal circuit. This crystal provides clock source to the on-chip real-time counter circuits. RESETN This pin resets the chip if it is low. This pin is pulled up to VDDIO33 with an internal 10 k resistor. No external pull up resistors are needed. DEBUG This pin is used for JTAG interface. DEBUG=0: JTAG interface works for boundary scan. DEBUG=1: JTAG interface works for ARM debugging. TESTMODE 3 For Freescale factory use only. Must be externally connected to GND for normal operation. Electrical Characteristics This section provides the device-level and module-level electrical characteristics for the i.MX28. 3.1 i.MX28 Device-Level Conditions This section provides the device-level electrical characteristics for the IC. 3.1.1 DC Absolute Maximum Ratings Table 6 provides the DC absolute maximum operating conditions. * CAUTION Stresses beyond those listed under Table 6 may cause permanent damage to the device. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 11 Electrical Characteristics * Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Table 6 gives stress ratings only--functional operation of the device is not implied beyond the conditions indicated in Table 8. * Table 6. DC Absolute Maximum Ratings Parameter Symbol Min. Max. Unit BATT, VDD4P2V -0.3 4.242 V 5-Volt Source Pin - transient, t<30ms, duty cycle <0.05% VDD5V -0.3 7.00 V 5 Volt Source Pin - static VDD5V -0.3 6.00 V Analog Supply Voltage VDDA -0.3 2.10 V Digital Core Supply Voltage VDDD -0.3 1.575 V Non-EMI Digital I/O Supply VDDIO -0.3 3.63 V VDDIO.EMI -0.3 3.63 V DCDC_BATT -0.3 BATT V Input Voltage on Any Digital I/O Pin Relative to Ground -- -0.3 VDDIO+0.3 V Input Voltage on USB_DP and USB_DN Pins Relative to Ground2 -- -0.3 3.63 V Analog I/O absolute maximum ratings (exceptions: XTALI, XTALO, RTC_XTALI, RTC_XTALO) -- -0.3 VDDIO+0.3 V Storage Temperature -- -40 125 C Battery Pin EMI Digital I/O Supply DC-DC Converter1 1 2 Application should include a Schottky diode between BATT and VDD4P2. USB_DN and USB_DP can tolerate 5V for up to 24 hours. Note that while 5V is applied to USB_DN or USB_DP, LRADC readings can be corrupted. Table 7 shows the electrostatic discharge immunity. Table 7. Electrostatic Discharge Immunity 289-Pin BGA Package Human Body Model (HBM)1 Charge Device Model 1 Tested Level 2 kV (CDM)1 500 V HBM and CDM pass ESD testing per AEC-Q100. i.MX28 Applications Processors for Consumer Products, Rev. 3 12 Freescale Semiconductor Electrical Characteristics 3.1.2 DC Operating Conditions Table 8 provides the DC recommended operating conditions. Table 8. Recommended Power Supply Operating Conditions Parameter Symbol Min Typ Max Unit Analog Core Supply Voltage VDDA 1.62 -- 2.10 V Digital Core Supply Voltage Specification dependent on frequency.1, 2 VDDD 1.35 -- 1.55 V 3.0 1.7 -- -- 3.6 1.9 1.7 1.425 1.8 1.5 1.9 1.625 BATT DCDC_BATT 3.103 -- 4.242 V -- 4.75 5.00 5.25 V * 32-kHz RTC off, BATT = 4.2 V -- -- 21 47 A * 32-kHz RTC on, BATT = 4.2 V -- -- 23 51 A VDDIO33/VDDIO33_EMI/V DDI Digital Supply Voltages: * VDDIO33/VDDIO33_EMI * VDDIO18 O18 VDDIO.EMI/VDDIO_EMIQ EMI Digital I/O Supply Voltage: * DDR2/mDDR * LVDDR2 Battery / DCDC Input Voltage--BATT, DCDC_BATT VDD5V Supply Voltage Offstate V V Current:4 1 For optimum USB jitter performance, VDDD = 1.35 V or greater. VDDD supply minimum voltage includes 75 mV guardband. 3 Tested with only the i.MX28 processor loading the MX28 PMU output rails during start up. With external loadings (for example, one DDR2 device and SD Card/NAND Flash), MX28 PMU was tested at BATT/DCDC_BATT > 3.30 V. 4 When the real-time clock is enabled, the chip consumes additional current in the OFF state to keep the crystal oscillator and the real-time clock running. 2 Table 9 provides the DC operating temperature conditions. Table 9. Operating Temperature Conditions Parameter1, 2, 3 Symbol Min Typ Max Unit Commercial Ambient Operating Temperature Range TA -20 -- 70 C Commercial Junction Temperature Range TJ -20 -- 85 C Industrial Ambient Operating Temperature Range TA -40 -- 85 C Industrial Junction Temperature Range TJ -40 -- 105 C 1 In most portable systems designs, battery and display specifications limits the operating range to well within these specifications. Most battery manufacturers recommend enabling battery charge only when the ambient temperature is between 0C and 40C. To ensure that battery charging does not occur outside the recommended temperature range, the system ambient temperature may be monitored by connecting a thermistor to the LRADC0 or LRADC6 pin on the i.MX28. 2 For applications powered by external 5V only, the Maximum Ambient Operating Temperature specified in Table 9 may not be achieved. Application developers need to do the worst-case power consumption estimation, and then calculate the Total On-chip Power Dissipation based on the equations specified in note 3 below. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 13 Electrical Characteristics 3 Maximum Ambient Operating Temperature may be limited due to on-chip power dissipation. TA (MAX) TJ - (JA x PD) where: TJ = Maximum Junction Temperature JA = Package Thermal Resistance. See Section 3.2, "Thermal Characteristics." PD = Total On-chip Power Dissipation =PVDD4P2 + PBatteryCharger + PDCDC + PLinearRegulators + PInternal. Depending on the application, some of these power dissipation terms may not apply. PVDD4P2 = VDD4P2 On-Chip Power Dissipation = (VDD5V - VDD4P2) x IDD4P2 PBatteryCharger = Battery Charger On-Chip Power Dissipation = (VDD5V - BATT) x ICHARGE PDCDC = DC-DC Converter On-Chip Power Dissipation = (BATT x DCDC Input Current) x (1 - efficiency) PLinearRegulators = Linear Regulator On-Chip Power Dissipation = (VDD5V - VDDIO) x (IDDIO + IDDA + IDDD + IDD1P5) + (VDDIO - VDDA) x (IDDA + IDDD) + (VDDA - VDDD) x IDDD + (VDDA - VDD1P5) x IDD1P5 PInternal = Internal Digital On-Chip Power Dissipation = ~VDDD x IDDD Table 10 provides the recommended analog operating conditions. Table 10. Recommended Analog Operating Conditions Parameter Low Resolution ADC Input Impedance (CH0 - CH5) Min Typ Max Unit >1 -- -- M Table 11 shows the PSWITCH input characteristics. See the reference schematics for the recommended PSWITCH button circuitry. Table 11. PSWITCH Input Characteristics Parameter HW_PWR_STS_PSWITCH Min Max Unit PSWITCH LOW LEVEL 0x00 0.00 0.30 V PSWITCH MID LEVEL & STARTUP1 0x01 0.65 1.50 V 0x11 (1.1 * VDDXTAL) + 0.58 2.45 V PSWITCH HIGH LEVEL2 1 A MID LEVEL PSWITCH state can be generated by connecting the VDDXTAL output of the SoC to PSWITCH through a switch. 2 PSWITCH acts like a high impedance input (>300 k) when the voltage applied to it is less than 1.5V. However, above 1.5V it becomes lower impedance. To simplify design, it is recommended that a 10 k resistor to VDDIO be applied to PSWITCH to set the HIGH LEVEL state (the PSWITCH input can tolerate voltages greater than 2.45 V as long as there is a 10 k resistor in series to limit the current). Table 12 shows a test case example for Run IDD. Table 12. Run IDD Test Case 1,2 Power Rail Conditions Min Typ Max Unit VDDD 1.57 V -- 150 188 mA VDDIO33 3.62 V -- 31 34 mA VDDA 2.12 V -- 1.11 1.17 mA VDDIO_EMI 1.92 V -- 1.01 1.08 mA VDDIO18 1.92 V -- 0.61 2.97 A 1 2 CPUCLK = 300 MHz, AHBCLK = 150 MHz Continuous read / write to the cache memory i.MX28 Applications Processors for Consumer Products, Rev. 3 14 Freescale Semiconductor Electrical Characteristics Table 13 illustrates the power supply characteristics. Table 13. Power Supply Characteristics Parameter Min Typ Max Unit -3 -- +3 % 270 -- -- mA Linear Regulators Output Voltage Accuracy (VDDIO, V DDA, VDDM, VDDD)1 VDDIO Maximum Output Current (VDDIO = 3.30 V, VDD5V = 4.75 V) 2, 3 VDDM Maximum Output Current (VDDM = 1.5 V)2 160 -- -- mA 2, 3 VDDA Maximum Output Current (VDDA = 1.8 V) 225 -- -- mA VDDD Maximum Output Current (VDDD = 1.2 V)2, 3 200 -- -- mA Output Voltage Accuracy (DCDC_VDDIO, DCDC_VDDA, DCDC_VDDD)1 -3 -- +3 % DCDC_VDDD Maximum Output Current (VDDD = 1.55 V)4, 5 250 -- -- mA DCDC_VDDA Maximum Output Current (VDDA = 1.8 V)4, 5 200 -- -- mA DCDC_VDDIO Maximum Output Current (VDDIO = 3.15 V, 3.3 V < BATT < 4.242 V)4, 5, 6 250 -- -- mA VDD4P2 Output Voltage Accuracy (TARGET=4.2V)1 -3 -- +3 % VDD4P2 Output Current Limit Accuracy (VDD5V = 4.75 V, ILIMIT=480 mA)7 480 500 520 mA VDD4P2 Output Current Limit Accuracy (VDD5V=4.75 V, ILIMIT=100 mA)7 100 120 140 mA -2 -- +1 % DCDC Converters VDD4P2 Regulated Output Battery Charger Final Charge Voltage Accuracy (TARGET=4.2 V) 1 2 3 4 5 6 7 No load. Maximum output current measured when output voltage droops 100 mV from the programmed target voltage with no load present. Because the internal linear regulators are cascaded, it is not possible to simultaneously operate the VDDIO, VDDA, VDDM, and VDDD linear regulators at the maximum specified load current. For example, the VDDIO linear regulator provides current to both the VDDIO 3.3 V supply rail as well as the VDDM and VDDA linear regulator inputs. Likewise, the VDDA linear regulator provides current to both the 1.8 V supply rail as well as the VDDD linear regulator input. The application designer should ensure the following two conditions are met: (V DDIO Load Current + VDDM Load Current + VDDA Load Current) < VDDIO Maximum Output Current (V DDA Load Current + VDDD Load Current) < VDDA Maximum Output Current DCDC Double FETs Enabled, Inductor Value = 15 H. The DCDC Converter is a triple output buck converter. The maximum output current capability of each output of the converter is dependent on the loads on the other two outputs. For a given output, it may be possible to achieve a maximum output current higher than that specified by ensuring the load on the other outputs is well below the maximum. Assumes simultaneous load of IDDD = 250 mA@ 1.55 V and IDDA = 200 mA@1.8 V. Untuned. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 15 Electrical Characteristics 3.1.2.1 Recommended Operating Conditions for Specific Clock Targets Table 14 through Table 17 provide the recommended operating conditions for specific clock targets. Table 14. Recommended Operating States--289-Pin BGA Package HW_ HW_ CLKCTRL CLKCTRL HW_ CLKCTRL EMICLK / clk_emi FRAC_ CPUFRC / PFD Frequency (MHz) HBUS_DI V Frequency (MHz) EMI_ DIV_EMI FRAC_ EMIFRAC 5 27 64 1 130.91 2 33 DDR2 mDDR 261.81 1 33 130.91 2 130.91 2 33 DDR2 mDDR 00 360 1 24 120.00 3 130.91 2 33 DDR2 mDDR 1.350 00 392.72 1 22 130.91 3 160.00 2 27 DDR2 mDDR 1.450 00 454.73 1 19 151.57 3 205.71 2 21 DDR2 mDDR CPUCLK / clk_p HW_ CLKCTRL ARMCACH E1 Frequency (MHz) CPU_DIV_CP U VDDD (V) 1.300 1.200 00 64 1.350 1.250 00 1.350 1.250 1.450 1.550 1 HW_ CLKCTRL AHBCLK / clk_h HW_ DIGCTRL VDDD Brown-out (V) Supported DRAM All timing control bit fields in HW_DIGCTRL_ARMCACHE should be set to the same value. Table 15. Recommended Operating Conditions--CPU Clock (clk_p) 1 VDDD (V) VDDDBrown-out (V) HW_DIGCTRL ARMCACHE1 1.350 1.250 00 18 - 35 360 1.450 1.350 00 18 - 35 392.72 1.550 1.450 00 18 - 35 454.73 HW_CLKCTRL CPUCLK / clk_p FRAC_CPUFRC / PFD Frequency max (MHz) All timing control bit fields in HW_DIGCTRL_ARMCACHE should be set to the same value. Table 16. Recommended Operating Conditions--AHB Clock (clk_h) 1 HW_CLKCTRL AHBCLK / clk_h FRAC_CPUFRC / PFD Frequency max (MHz) VDDD (V) VDDDBrown-out (V) HW_DIGCTRL ARMCACHE1 1.350 1.250 00 18 - 35 160 1.450 1.350 00 18 - 35 196 1.550 1.45 00 18 - 35 206 All timing control bit fields in HW_DIGCTRL_ARMCACHE should be set to the same value. i.MX28 Applications Processors for Consumer Products, Rev. 3 16 Freescale Semiconductor Electrical Characteristics Table 17. Frequency vs. Voltage for EMICLK--289-Pin BGA Package EMICLK Fmax (MHz) VDDD (V) 3.1.3 VDDDBrownout (V) DDR2 mDDR 1.550 1.450 205.71 205.71 1.450 1.350 196.36 196.36 1.350 1.250 196.36 196.36 Fusebox Supply Current Parameters Table 18 lists the fusebox supply current parameters. Table 18. Fusebox Supply Current Parameters Parameter eFuse Program Current1 Current to program one eFuse bit efuse_vddq=2.5V eFuse Read Current2 Current to read an 8-bit eFuse word vdd_fusebox = 3.3 V 1 2 Symbol Min Typ Max Unit Iprogram 21.39 25.05 33.54 mA Iread -- -- 4.07 mA The current Iprogram is during program time. The current Iread is present for approximately 10 ns of the read access to the 8-bit word. 3.1.4 Interface Frequency Limits Table 19 provides information for interface frequency limits. Table 19. Interface Frequency Limits Parameter Min. Typ. Max. Unit JTAG: TCK Frequency of Operation -- -- 10 MHz OSC24M_XTAL Oscillator -- 24.000 -- MHz OSC32K_XTAL Oscillator -- 32.768/32.0 -- kHz 3.1.5 Power Modes Table 20 describes the core, clock, and module settings for the different power modes of the processor. Table 20. Power Mode Settings Core/Clock/Module Offstate Standby Run ARM Core Off Off On USB0 PLL (System PLL) Off Off On OSC24M Off On On i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 17 Electrical Characteristics Table 20. Power Mode Settings (continued) Core/Clock/Module 3.1.6 Offstate Standby Run OSC32K On On On DCDC Off On On RTC On On On Other Modules Off On/Off On/Off Supply Power-Up/Power-Down Requirements There is no special power-up sequence. After applying 5 V or battery in any order, the rest of the power supplies are internally generated and automatically come up in a safe way. There is no special power-down sequence. 5 V or the battery can be removed at any time. 3.1.7 Reset Timing Because the i.MX28 is a PMU and an SoC, power-on reset is generated internally and there is no timing requirement on external pins. The i.MX28 can be reset by asserting the external pin RESETN for at least 100 mS and later deasserting RESETN. If the reset occurs while the device is only powered by the battery, then the reset kills all of the power supplies and the system reboots on the assertion of PSWITCH. If auto-restart is set up ahead of time, the system reboots immediately. If the chip is powered by 5 V, then the reset serves to reset the digital sections of the chip. If the DCDC is operating at the time of the reset, then power switches back to the default linear regulators powered by 5 V. RESETN At least 100ms Figure 2. RESETN Timing 3.2 Thermal Characteristics The thermal resistance characteristics for the device are given in Table 21. These values are measured under the following conditions: * Two layer Substrate * Substrate solder mask thickness: 0.025 mm * Substrate metal thicknesses: 0.016 mm * Substrate core thickness: 0.160 mm i.MX28 Applications Processors for Consumer Products, Rev. 3 18 Freescale Semiconductor Electrical Characteristics * * * * Core via I.D: 0.068 mm, Core via plating 0.016 mm Flag: trace style with ground balls under the die connected to the flag Die Attach: 0.033 mm non-conductive die attach, k = 0.3 W/m K Mold Compound: generic mold compound, k = 0.9 W/m K Table 21. Thermal Resistance Data Rating Value Unit Junction to ambient1 natural convection Single layer board (1s) RJA 62 C/W Junction to ambient1 natural convection Four layer board (2s2p) RJA 36 C/W Junction to ambient1 (@200 ft/min) Single layer board (1s) RJMA 53 C/W Junction to ambient1 (@200 ft/min) Four layer board (2s2p) RJMA 33 C/W RJB 24 C/W RJCtop 15 C/W JT 3 C/W Junction to boards2 Junction to case (top)3 Junction to package top4 Natural Convection 1 Junction-to-Ambient Thermal Resistance determined per JEDEC JESD51-2 and JESD51-6. Thermal test board meets JEDEC specification for this package. 2 Junction-to-Board thermal resistance determined per JEDEC JESD51-8. Thermal test board meets JEDEC specification for the specified package. 3 Junction-to-Case at the top of the package determined using MIL-STD 883 Method 1012.1. The cold plate temperature is used for the case temperature. Reported value includes the thermal resistance of the interface layer. 4 Thermal characterization parameter indicating the temperature difference between the package top and the junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT. 3.3 I/O DC Parameters This section includes the DC parameters of the following I/O types: * DDR I/O: Mobile DDR (LPDDR1), standard 1.8 V DDR2, and low-voltage 1.5 V DDR2 (LVDDR2) * General purpose I/O (GPIO) 3.3.1 DDR I/O DC Parameters Table 22 shows the EMI digital pin DC characteristics. NOTE The current values and the I-V curves of the I/O DC characteristics are estimated based on an overly conservative device model. They are updated upon the measurement results of the first silicon. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 19 Electrical Characteristics Table 22. EMI Digital Pin DC Characteristics Parameter Symbol Min. Max. Unit Input voltage high (dc) VIH VREF + 0.125 VDDIO_EMI + 0.3 V Input voltage low (dc) VIL 0.3 VREF - 0.125 V Output voltage high (dc) VOH 0.8 * VDDIO_EMI -- V Output voltage low (dc) VOL - 0.2 * VDDIO_EMI V Output source current (dc) LVDDR2 Mode IOH1--Low -6.2 -- mA IOH--Medium -7.2 -- mA IOH--High -9.7 -- mA IOL2--Low 5.7 -- mA IOL--Medium 7.3 -- mA IOL--High 10.0 -- mA Output source current (dc) mDDR, DDR2 Mode IOH--Low -5.7 -- mA IOH--High -7.5 -- mA Output sink current (dc) mDDR, DDR2 Mode IOL--Low 5.4 -- mA IOL--High 8.8 -- mA Output sink current (dc) LVDDR2 Mode 1 2 IOH is the output current at which the VOH specification is met. IOL is the output current at which the VOL specification is met. Table 23 shows the ON impedance of EMI drivers for different drive strengths. Table 23. ON Impedance of EMI Drivers for Different Drive Strengths1 Mode Drive Min. () Typ. () Max. () 1.5 LVDDR2 Low 26 38 58 Medium 17 25 36 High 15 20 27 Low 36 53 78 Medium 17 27 42 High 16 19 28 1.8 DDR2/mDDR 1 ON impedance of the EMI drivers are guaranteed by design and are not tested during production. i.MX28 Applications Processors for Consumer Products, Rev. 3 20 Freescale Semiconductor Electrical Characteristics Table 24 shows the external devices supported by the EMI. Table 24. External Devices Supported by the EMI 1 2 DRAM Device Max Load1, 2 Pad Voltage DDR2 15 pF 1.8 V mDDR 15 pF 1.8 V LVDDR2 15 pF 1.5 V Max load includes capacitive load due to PCB traces, pad capacitance and driver self-loading. Setting is for worst case. Freescale's EMI interface uses less powerful drivers than those typically used in mDDR devices. A possible transmission-line effect on the PC board must be suppressed by minimizing the trace length combined with Freescale's slower edge-rate drivers. The i.MX28 provides up to 16 mA programmable drive strength. However, the 16-mA mode is an experimental mode. With the 16-mA mode, the EMI function may be impaired by Simultaneous Switching Output (SSO) noise. In general, the stronger the driver mode, the noisier the on-chip power supply. Freescale recommends not using a stronger driver mode than is required. Because on-chip power and ground noise is proportional to the inductance of its return path, users should make their best effort to reduce inductance between the EMI power and ground balls and the PC board power and ground planes. 3.3.2 GPIO I/O DC Parameters Max load includes capacitive load due to PCB traces, pad capacitance and driver self-loading. For the internal pull up setting of each pad, see the "Pin Control and GPIO" section of the reference manual. Table 25 shows the digital pin DC characteristics for GPIO in 3.3-V mode. Measurements are valid for eight pins loaded using the 4mA driver, four pins loaded using the 8mA driver, and two pins loaded using either the 12mA or 16mA driver. Table 25. Digital Pin DC Characteristics for GPIO in 3.3-V Mode Parameter Symbol Min Max Unit Input voltage high (dc) VIH 2 VDDIO V Input voltage low (dc) VIL -- 0.8 V Output voltage high (dc) VOH 0.8 x VDDIO -- V Output voltage low (dc) VOL -- 0.4 V IOH - Low -5.0 -- mA IOH - Medium -9.5 -- mA IOH - High -11.4 -- mA IOL - Low 3.8 -- mA IOL - Medium 7.7 -- mA IOL - High 9.0 -- mA IOH - Low -9.2 -- mA IOH - High -15.2 -- mA IOL - Low 7.6 -- mA IOL - High 12.0 -- mA Output source gpio current1 (dc) Output sink current (dc) gpio Output source current (dc) gpio_clk Output sink current (dc) gpio_clk i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 21 Electrical Characteristics Table 25. Digital Pin DC Characteristics for GPIO in 3.3-V Mode (continued) Parameter Symbol Min Max Unit 10-K pull-up resistance2 Rpu10k 8 12 k 47-K pull-up resistance Rpu47k 39 56 k 1 The conditions of the current measurements for all different drives are as follows: IOL: at 0.4 V IOH: at VDDIO * 0.8 V Maximum corner for 3.3 V mode: 3.6 V, -40C, fast process. Minimum corner for 3.3 V mode: 3.0 V, 105C, slow process. 8 gpio pins (LCD_D0-D7) and 2 gpio_clk pins (LCD_DOTCLK and LCD_WR_RWN) simultaneously loaded. 2 See the i.MX28 reference manual for detailed pull-up configuration of each I/O. Table 26 shows the digital pin DC characteristics for GPIO in 1.8 V mode. Table 26. Digital Pin DC Characteristics for GPIO in 1.8 V Mode Symbol Min Max Unit Input voltage high (DC) VIH 0.7 x VDDIO18 VDDIO18 V Input voltage low (DC) VIL -- 0.3 x VDDIO18 V Output voltage high (DC) VOH 0.8 * VDDIO18 -- V Output voltage low (DC) VOL -- 0.2 x VDDIO18 V Output source current1 (DC) gpio IOH - low -2.2 -- mA IOH - medium -3.5 -- mA IOH - high -4.0 -- mA IOL - low 3.3 -- mA IOL - medium 7.0 -- mA IOL - high 7.5 -- mA IOH - low -4.2 -- mA IOH - high -6.0 -- mA IOL - low 6.8 -- mA IOL - high 11.5 -- mA 10-K pull-up resistance2 Rpu10k 8 12 k 47-K pull-up resistance Rpu47k 39 56 k Output sink current (DC) gpio Output source current (DC) gpio_clk Output sink current (DC) gpio_clk 1 The condition of the current measurements for all different drives are as follows: Maximum corner for 1.8 V mode: 1.9 V, -40C, Fast process. Minimum corner for 1.8 V mode: 1.7 V, 105C, Slow process. 1 gpio pin (GPMI_D0) and 1 gpio_clk pin (GPMI_WRN) simultaneously loaded. 2 See the i.MX28 reference manual for detailed pull-up configuration of each I/O. i.MX28 Applications Processors for Consumer Products, Rev. 3 22 Freescale Semiconductor Electrical Characteristics 3.4 I/O AC Timing and Parameters Figure 3 and Figure 4 show the Driver Used for AC Simulation Testpoint and the Output Pad Transition Waveform. Driver Used for AC simulation Testpoint Figure 3. Driver Used for AC Simulation Testpoint Output Pad Transition Waveform VDDIO 80% 20% Figure 4. Output Pad Transition Waveform Table 27 shows the base GPIO AC timing and parameters. Table 27. Base GPIO Parameters Symbol Test Voltage Test Capacitance Min Rise/Fall MaxRise/Fall Unit Notes Duty cycle Fduty -- -- -- -- % -- Output pad transition times (maximum drive) tpr 1.7~1.9V 10 pF 0.82 0.91 1.93 1.97 ns -- 1.7~1.9V 20 pF 1.18 1.22 2.69 2.71 -- 1.7~1.9V 50 pF 2.11 2.03 4.62 4.44 -- 3.0~3.6V 10 pF 1.04 1.08 2.46 2.18 -- 3.0~3.6V 20 pF 1.42 1.5 3.29 3 -- 3.0~3.6V 50 pF 2.46 2.61 5.34 5.12 -- i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 23 Electrical Characteristics Table 27. Base GPIO (continued) Min Rise/Fall Parameters Symbol Test Voltage Test Capacitance Output pad transition times (medium drive) tpr 1.7~1.9V 10 pF 1.02 1.08 2.34 2.38 1.7~1.9V 20 pF 1.51 1.5 3.34 3.28 -- 1.7~1.9V 50 pF 2.91 2.62 6.24 5.67 -- 3.0~3.6V 10 pF 1.26 1.29 2.9 2.6 -- 3.0~3.6V 20 pF 1.8 1.88 4 3.67 -- 3.0~3.6V 50 pF 3.3 3.46 6.91 6.64 -- 1.7~1.9V 10 pF 1.62 1.68 3.65 3.68 1.7~1.9V 20 pF 2.55 2.45 5.59 5.37 -- 1.7~1.9V 50 pF 5.42 4.62 11.46 10.01 -- 3.0~3.6V 10 pF 1.95 2.12 4.43 4.25 -- 3.0~3.6V 20 pF 2.96 3.21 6.36 6.25 -- 3.0~3.6V 50 pF 5.89 6.39 12.02 12.18 -- 1.7~1.9V 10 pF 1.39 1.25 0.53 0.52 1.7~1.9V 20 pF 0.97 0.93 0.38 0.38 -- 1.7~1.9V 50 pF 0.54 0.56 0.22 0.23 -- 3.0~3.6V 10 pF 2.08 2.00 0.73 0.83 -- 3.0~3.6V 20 pF 1.52 1.44 0.55 0.60 -- 3.0~3.6V 50 pF 0.88 0.83 0.34 0.35 -- 1.7~1.9V 10 pF 1.12 1.06 0.44 0.43 1.7~1.9V 20 pF 0.75 0.76 0.31 0.31 -- 1.7~1.9V 50 pF 0.39 0.44 0.16 0.18 -- 3.0~3.6V 10 pF 1.71 1.67 0.62 0.69 -- 3.0~3.6V 20 pF 1.20 1.15 0.45 0.49 -- 3.0~3.6V 50 pF 0.65 0.62 0.26 0.27 -- 1.7~1.9V 10 pF 1.17 1.13 0.47 0.46 1.7~1.9V 20 pF 0.75 0.78 0.30 0.32 -- 1.7~1.9V 50 pF 0.35 0.41 0.15 0.17 -- 3.0~3.6V 10 pF 1.11 1.02 0.41 0.42 -- 3.0~3.6V 20 pF 0.73 0.67 0.28 0.29 -- 3.0~3.6V 50 pF 0.37 0.34 0.15 0.15 -- 1.7 V-1.9 V -- 100 75 3.0 V-3.6 V -- 100 50 Output pad transition times (low drive) Output pad slew rate (maximum drive) Output pad slew rate (medium drive) Output pad slew rate (low drive) Input pad average hysteresis tpr tps tps tps tih MaxRise/Fall Unit Notes ns -- ns V/ns V/ns V/ns mV -- -- -- -- -- -- i.MX28 Applications Processors for Consumer Products, Rev. 3 24 Freescale Semiconductor Electrical Characteristics Table 28 shows the F-type GPIO AC timing and parameters. Table 28. F-type GPIO Parameters Symbol Test Voltage Duty cycle Fduty -- -- Output pad transition times (maximum drive) tpr 1.7~1.9V 10 pF 0.58 0.61 1.29 1.33 1.7~1.9V 20 pF 0.89 0.88 1.94 1.88 -- 1.7~1.9V 50 pF 1.83 1.59 3.88 3.39 -- 3.0~3.6V 10 pF 0.71 0.68 1.47 1.34 -- 3.0~3.6V 20 pF 1.02 1.04 2.11 1.99 -- 3.0~3.6V 50 pF 1.98 2.09 3.97 3.96 -- 1.7~1.9V 10 pF 0.76 0.76 1.68 1.61 1.7~1.9V 20 pF 1.23 1.13 2.63 2.38 -- 1.7~1.9V 50 pF 2.66 2.18 5.61 4.6 -- 3.0~3.6V 10 pF 0.9 0.88 1.84 1.7 -- 3.0~3.6V 20 pF 1.36 1.4 2.76 2.67 -- 3.0~3.6V 50 pF 2.85 3.02 5.59 5.67 -- 1.7~1.9V 10 pF 1.32 1.26 2.88 2.72 1.7~1.9V 20 pF 2.27 1.98 4.84 4.23 -- 1.7~1.9V 50 pF 5.23 4.13 10.95 8.8 -- 3.0~3.6V 10 pF 1.46 1.55 3.05 3 -- 3.0~3.6V 20 pF 2.46 2.62 4.92 5.02 -- 3.0~3.6V 50 pF 5.56 5.96 10.78 11.22 -- 1.7~1.9V 10 pF 1.97 1.87 0.79 0.77 1.7~1.9V 20 pF 1.28 1.30 0.53 0.54 -- 1.7~1.9V 50 pF 0.62 0.72 0.26 0.30 -- 3.0~3.6V 10 pF 3.04 3.18 1.22 1.34 -- 3.0~3.6V 20 pF 2.12 2.08 0.85 0.90 -- 3.0~3.6V 50 pF 1.09 1.03 0.45 0.45 -- 1.7~1.9V 1.7~1.9V 10 pF 20 pF 1.50 0.93 1.50 1.01 0.61 0.39 0.63 0.43 1.7~1.9V 50 pF 0.43 0.52 0.18 0.22 -- 3.0~3.6V 10 pF 2.40 2.45 0.98 1.06 -- 3.0~3.6V 20 pF 1.59 1.54 0.65 0.67 -- 3.0~3.6V 50 pF 0.76 0.72 0.32 0.32 -- Output pad transition times (medium drive) Output pad transition times (low drive) Output pad slew rate (maximum drive) Output pad slew rate (medium drive) tpr tpr tps tps Test Capacitance Min Rise/Fall Max Rise/Fall -- -- Unit Notes % -- ns -- ns ns ns ns -- -- -- -- -- i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 25 Electrical Characteristics Table 28. F-type GPIO (continued) Parameters Symbol Test Voltage Output pad slew rate (low drive) tps 1.7~1.9V 1.7~1.9V 10 pF 20 pF 1.44 0.84 1.51 0.96 0.59 0.35 0.63 0.40 1.7~1.9V 50 pF 0.36 0.46 0.16 0.19 -- 3.0~3.6V 10 pF 1.48 1.39 0.59 0.60 -- 3.0~3.6V 20 pF 0.88 0.82 0.37 0.36 -- 3.0~3.6V 50 pF 0.39 0.36 0.17 0.16 -- 1.7 V-1.9 V -- 100 75 3.0 V-3.6 V -- 100 50 Input pad average hysteresis tih Test Capacitance Min Rise/Fall Max Rise/Fall Unit Notes ns -- -- mV -- -- Table 29 shows the CLK-type GPIO AC timing and parameters. Table 29. CLK-Type GPIO Parameters Symbol Duty cycle Fduty -- -- Output pad transition times (maximum drive) tpr 1.7~1.9V 10 pF 0.48 0.52 1.08 1.12 1.7~1.9V 20 pF 0.72 0.74 1.56 1.56 -- 1.7~1.9V 50 pF 1.41 1.28 3.04 2.7 -- 3.0~3.6V 10 pF 0.61 0.57 1.25 1.12 -- 3.0~3.6V 20 pF 0.85 0.85 1.73 1.63 -- 3.0~3.6V 50 pF 1.56 1.63 3.13 3.08 -- 1.7~1.9V 10 pF 0.76 0.76 1.67 1.62 1.7~1.9V 20 pF 1.22 1.14 2.64 2.41 -- 1.7~1.9V 50 pF 2.66 2.2 5.61 4.62 -- 3.0~3.6V 10 pF 0.9 0.89 1.83 1.72 -- 3.0~3.6V 20 pF 1.37 1.41 2.77 2.69 -- 3.0~3.6V 50 pF 2.85 3.03 5.59 5.72 -- 1.7~1.9V 10 pF 2.38 2.19 0.94 0.91 1.7~1.9V 20 pF 1.58 1.54 0.65 0.65 -- 1.7~1.9V 50 pF 0.81 0.89 0.34 0.38 -- 3.0~3.6V 10 pF 3.54 3.79 1.44 1.61 -- 3.0~3.6V 20 pF 2.54 2.54 1.04 1.10 -- 3.0~3.6V 50 pF 1.38 1.33 0.58 0.58 -- Output pad transition times (medium drive) Output pad slew rate (maximum drive) tpr tps Test Voltage Test Capacitance Min Rise/Fall Max Rise/Fall units Notes -- -- % -- ns -- ns ns -- -- i.MX28 Applications Processors for Consumer Products, Rev. 3 26 Freescale Semiconductor Electrical Characteristics Table 29. CLK-Type GPIO (continued) Parameters Symbol Output pad slew rate (medium drive) tps Input pad average hysteresis 3.5 tih Test Voltage Test Capacitance Min Rise/Fall Max Rise/Fall units Notes ns -- 1.7~1.9V 10 pF 1.50 1.50 0.61 0.63 1.7~1.9V 20 pF 0.93 1.00 0.39 0.42 -- 1.7~1.9V 50 pF 0.43 0.52 0.18 0.22 -- 3.0~3.6V 10 pF 2.40 2.43 0.98 1.05 -- 3.0~3.6V 20 pF 1.58 1.53 0.65 0.67 -- 3.0~3.6V 50 pF 0.76 0.71 0.32 0.31 -- 1.7 V-1.9 V -- 100 75 3.0 V-3.6 V -- 100 50 mV -- -- Module Timing and Electrical Parameters 3.5.1 ADC Electrical Specifications This section describes the electrical specifications, including DC and AC information, of Low-Resolution ADC (LRADC) and High-Speed ADC (HSADC). 3.5.1.1 LRADC Electrical Specifications Table 30 shows the electrical specifications for the LRADC. Table 30. LRADC Electrical Specifications Parameter Conditions Min. Typ. Max. Unit -- 0.5 -- pF AC Electrical Specification Input capacitance (Cp) No pin/pad capacitance included Resolution -- Maximum sampling rate1 (fs) -- Power-up time2 -- 12 -- -- bits 428 1 kHz sample cycles DC Electrical Specification DC input voltage Current VDDA consumption3 0 -- 1.85 V -- 10 -- A 200 -- 50000 Touchscreen Interface Expected plate resistance 1 2 -- There is no sample and hold circuit in LRADC, so it is only for DC input voltage or ones with very small slope. This comprises only the required initial dummy conversion cycle, NOT including the Analog part power-up time. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 27 Electrical Characteristics 3 This value only includes the ADC and the driver switches, but it does not take into account the current consumption in the touchscreen plate. For example, if the plate resistance is 200 ohm, the total current consumption is about 11 mA. 3.5.1.2 HSADC Electrical Specification Table 31 shows the electrical specifications for the HSADC Table 31. HSADC Electrical Specification Parameter Conditions Min. Typ. Max. -- 0.5 -- Unit AC Electrical Specification Input sampling capacitance (C s) No pin/pad capacitance included Resolution -- Maximum sampling rate (fs) -- Power-up time -- 12 -- pF bits -- 2 1 MHz sample cycles DC Electrical Specification DC input voltage -- 0.5 -- VDDA-0.5 V Current Consumption VDDA -- -- 10 -- A DNL fin = 1 kHz -- 0.5 1.2 LSB INL fin = 1kHz -- 0.5 1.2 LSB i.MX28 Applications Processors for Consumer Products, Rev. 3 28 Freescale Semiconductor Electrical Characteristics 3.5.2 DPLL Electrical Specifications This section includes descriptions of the USB PLL electrical specifications and Ethernet PLL electrical specifications. 3.5.2.1 USB PLL Electrical Specifications The i.MX28 integrates a high-frequency USB PLL that provides the 480-MHz clock for the USB and other system blocks. Table 32 lists the USB PLL output electrical specifications. Table 32. USB PLL Specifications Parameter PLL lock time 3.5.2.2 Test Conditions Min Typ Max Unit -- -- -- 10 s Ethernet PLL Electrical Specifications i.MX28 provides a 50-MHz/25-MHz output clock, called the Ethernet PLL output. Table 33 lists the Ethernet PLL output electrical specifications. Table 33. Ethernet PLL Specifications Parameter Test Conditions Min Typ Max Unit Output Duty Cycle -- 45 50 55 % PLL lock time -- -- -- 10 s Cycle to cycle jitter -- -- 25 -- ps Clock output frequency tolerance1 -- -- -- +/-20 ppm 1 This Ethernet output clock tolerance specification is the contribution from the PLL only and assumes a perfect 24 MHz clock/crystal source with 0 ppm deviation. The 24 MHz crystal frequency tolerance/deviation should be added to this number for the total Ethernet clock output frequency tolerance. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 29 Electrical Characteristics 3.5.3 EMI AC Timing This section includes descriptions of the electrical specifications of EMI module which interfaces external DDR2 and Mobile-DDR1 (LP-DDR1) memory devices. 3.5.3.1 EMI Command and Address AC Timing Figure 5 and Table 34 specify the timing related to the address and command pins that interfaces DDR2 and Mobile-DDR1 memory devices. DDR2 DDR3 EMI_CLKN EMI_CLK DDR1 EMI_CE0N DDR4 DDR5 EMI_RASN EMI_CASN DDR4 EMI_WEN DDR5 DDR5 DDR4 bank row EMI_ADDR bank column Figure 5. EMI Command/Address AC Timing Table 34. EMI Command/Address AC Timing ID Description DDR1 CK cycle time DDR2 CK high level width DDR3 CK low level width Symbol Min. Max. Unit tCK 4.86 -- ns tCH 0.5 tCK -0.5 0.5 tCK + 0.5 ns tCL 0.5 tCK -0.5 0.5 tCK + 0.5 ns i.MX28 Applications Processors for Consumer Products, Rev. 3 30 Freescale Semiconductor Electrical Characteristics Table 34. EMI Command/Address AC Timing (continued) ID Description DDR4 Address and control output setup time DDR5 Address and control output hold time 3.5.3.2 Symbol Min. Max. Unit tIS 0.5 tCK - 1 0.5 tCK + 0.5 ns tIH 0.5 tCK - 1 0.5 tCK + 0.5 ns DDR Output AC Timing Figure 6 and Table 35 show the DDR output AC timing defined for all DDR types: LPDDR1, standard DDR2 (1.8 V), and LVDDR2 (1.5 V) EMI_CLKN EMI_CLK DDR10 DDR11 DDR12 EMI_DQSN EMI_DQS DDR13 EMI_DQ & EMI_DQM DDR14 d0 d1 d2 d3 DDR15 DDR16 Figure 6. DDR Output AC Timing Table 35. DDR Output AC Timing ID Description Symbol Min Max Unit DDR10 Positive DQS latching edge to associated CK edge tDQSS -0.5 0.5 ns DDR11 DQS falling edge from CK rising edge--hold time tDSH 0.5 tCK -0.5 0.5 tCK + 0.5 ns DDR12 DQS falling edge to CK rising edge--setup time tDSS 0.5 tCK -0.5 0.5 tCK + 0.5 ns DDR13 DQS output high pulse width tDQSH 0.5 tCK -0.5 0.5 tCK + 0.5 ns DDR14 DQS output low pulse width tDQSL 0.5 tCK -0.5 0.5 tCK + 0.5 ns i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 31 Electrical Characteristics Table 35. DDR Output AC Timing (continued) ID Description Symbol Min Max Unit DDR15 DQ & DQM output setup time relative to DQS tDS 1/4 tCK -0.8 1/4 tCK -0.5 ns DDR16 DQ & DQM output hold time relative to DQS tDH 1/4 tCK -0.8 1/4 tCK -0.5 ns 3.5.3.3 DDR2 Input AC Timing Figure 7 and Table 36 show input AC timing for standard DDR2 and LVDDR2. EMI_CLKN EMI_CLK DDR20 EMI_DQSN EMI_DQS DDR22 DDR21 EMI_DQ d0 d1 d2 d3 Figure 7. DDR2 Input AC Timing Table 36. DDR2 Input AC Timing ID DDR20 Description Positive DQS latching edge to associated CK edge DDR21 Symbol DQS to DQ input hold time Max Unit tDQSCK -0.5 0.5 ns tDQSQ 0.25 tCK -0.85 0.25 tCK -0.5 ns tQH 0.25 tCK +0.75 0.25 tCK +1 ns DQS to DQ input skew DDR22 Min i.MX28 Applications Processors for Consumer Products, Rev. 3 32 Freescale Semiconductor Electrical Characteristics 3.5.3.4 LPDDR1 Input AC Timing Figure 8 and Table 37 show input AC timing for LPDDR1. EMI_CLKN EMI_CLK DDR20 EMI_DQSN EMI_DQS DDR22 DDR21 EMI_DQ d0 d1 d2 d3 Figure 8. LPDDR1 Input AC Timing Table 37. DDR2 Input AC Timing ID Description Symbol Min Max Unit DDR20 Positive DQS latching edge to associated CK edge tDQSCK 2 6 ns DDR21 DQS to DQ input skew tDQSQ 0.25 tCK -0.85 0.25 tCK -0.5 ns DDR22 DQS to DQ input hold time tQH 0.25 tCK +0.75 0.25 tCK +1 ns 3.5.4 Ethernet MAC Controller (ENET) Timing The ENET is designed to support both 10- and 100-Mbps Ethernet networks compliant with IEEE 802.3. An external transceiver interface and transceiver function are required to complete the interface to the media. The ENET supports 10/100-Mbps MII (18 pins altogether), 10/100-Mbps RMII (10 pins, including serial management interface), for connection to an external Ethernet transceiver. All signals are compatible with transceivers operating at a voltage of 3.3 V. The following subsections describe the timing for MII and RMII modes. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 33 Electrical Characteristics 3.5.4.1 ENET MII Mode Timing This subsection describes MII receive, transmit, asynchronous inputs, and serial management signal timings. 3.5.4.1.1 MII Receive Signal Timing (ENET0_RXD[3:0], ENET0_RX_DV, ENET0_RX_ER, and ENET0_RX_CLK) The receiver functions correctly up to an ENET0_RX_CLK maximum frequency of 25 MHz + 1%. There is no minimum frequency requirement. Additionally, the processor clock frequency must exceed twice the ENET0_RX_CLK frequency. Figure 9 shows MII receive signal timings. Table 38 describes the timing parameters (M1-M4) shown in the figure. M3 ENET0_RX_CLK (input) M4 ENET0_RXD[3:0] (inputs) ENET0_RX_DV ENET0_RX_ER M1 M2 Figure 9. MII Receive Signal Timing Diagram Table 38. MII Receive Signal Timing Characteristic1 ID Min. Max. Unit M1 ENET0_RXD[3:0], ENET0_RX_DV, ENET0_RX_ER to ENET0_RX_CLK setup 5 -- ns M2 ENET0_RX_CLK to ENET0_RXD[3:0], ENET0_RX_DV, ENET0_RX_ER hold 5 -- ns M3 ENET0_RX_CLK pulse width high 35% 65% ENET0_RX_CLK period M4 ENET0_RX_CLK pulse width low 35% 65% ENET0_RX_CLK period 1 ENET0_RX_DV, ENET0_RX_CLK, and ENET0_RXD0 have the same timing in 10 Mbps 7-wire interface mode. 3.5.4.1.2 MII Transmit Signal Timing (ENET0_TXD[3:0], ENET0_TX_EN, ENET0_TX_ER, and ENET0_TX_CLK) The transmitter functions correctly up to an ENET0_TX_CLK maximum frequency of 25 MHz + 1%. There is no minimum frequency requirement. Additionally, the processor clock frequency must exceed twice the ENET0_TX_CLK frequency. i.MX28 Applications Processors for Consumer Products, Rev. 3 34 Freescale Semiconductor Electrical Characteristics Figure 10 shows MII transmit signal timings. Table 39 describes the timing parameters (M5-M8) shown in the figure. M7 ENET0_TX_CLK (input) M5 M8 ENET0_TXD[3:0] (outputs) ENET0_TX_EN ENET0_TX_ER M6 Figure 10. MII Transmit Signal Timing Diagram Table 39. MII Transmit Signal Timing Characteristic1 ID Min. Max. Unit M5 ENET0_TX_CLK to ENET0_TXD[3:0], ENET0_TX_EN, ENET0_TX_ER invalid 5 -- ns M6 ENET0_TX_CLK to ENET0_TXD[3:0], ENET0_TX_EN, ENET0_TX_ER valid -- 20 ns M7 ENET0_TX_CLK pulse width high 35% 65% ENET0_TX_CLK period M8 ENET0_TX_CLK pulse width low 35% 65% ENET0_TX_CLK period 1 ENET0_TX_EN, 3.5.4.1.3 ENET0_TX_CLK, and ENET0_TXD0 have the same timing in 10-Mbps 7-wire interface mode. MII Asynchronous Inputs Signal Timing (ENET0_CRS and ENET0_COL) Figure 11 shows MII asynchronous input timings. Table 40 describes the timing parameter (M9) shown in the figure. ENET0_CRS, ENET0_COL M9 Figure 11. MII Async Inputs Timing Diagram Table 40. MII Asynchronous Inputs Signal Timing ID M91 1 Characteristic ENET0_CRS to ENET0_COL minimum pulse width Min. Max. Unit 1.5 -- ENET0_TX_CLK period ENET0_COL has the same timing in 10-Mbit 7-wire interface mode. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 35 Electrical Characteristics 3.5.4.1.4 MII Serial Management Channel Timing (ENET0_MDIO and ENET0_MDC) The MDC frequency is designed to be equal to or less than 2.5 MHz to be compatible with the IEEE 802.3 MII specification. However the ENET can function correctly with a maximum MDC frequency of 15 MHz. Figure 12 shows MII asynchronous input timings. Table 41 describes the timing parameters (M10-M15) shown in the figure. M14 M15 ENET0_MDC (output) M10 ENET0_MDIO (output) M11 ENET0_MDIO (input) M12 M13 Figure 12. MII Serial Management Channel Timing Diagram Table 41. MII Serial Management Channel Timing ID Characteristic Min. Max. Unit M10 ENET0_MDC falling edge to ENET0_MDIO output invalid (min. propagation delay) 0 -- ns M11 ENET0_MDC falling edge to ENET0_MDIO output valid (max. propagation delay) -- 5 ns M12 ENET0_MDIO (input) to ENET0_MDC rising edge setup 18 -- ns M13 ENET0_MDIO (input) to ENET0_MDC rising edge hold 0 -- ns M14 ENET0_MDC pulse width high 40% 60% ENET0_MDC period M15 ENET0_MDC pulse width low 40% 60% ENET0_MDC period 3.5.4.2 RMII Mode Timing In RMII mode, ENET_CLK is used as the REF_CLK, which is a 50 MHz 50 ppm continuous reference clock. ENET0_RX_DV is used as the CRS_DV in RMII. Other signals under RMII mode include ENET0_TX_EN, ENET0_TXD[1:0], ENET0_RXD[1:0] and ENET0_RX_ER. i.MX28 Applications Processors for Consumer Products, Rev. 3 36 Freescale Semiconductor Electrical Characteristics Figure 13 shows RMII mode timings. Table 42 describes the timing parameters (M16-M21) shown in the figure. M16 M17 ENET_CLK (input) M18 ENET0_TXD[1:0] (output) ENET0_TX_EN M19 CRS_DV (input) ENET0_RXD[1:0] ENET0_RX_ER M20 M21 Figure 13. RMII Mode Signal Timing Diagram Table 42. RMII Signal Timing ID Characteristic Min. Max. Unit M16 ENET_CLK pulse width high 35% 65% ENET_CLK period M17 ENET_CLK pulse width low 35% 65% ENET_CLK period M18 ENET_CLK to ENET0_TXD[1:0], ENET0_TX_EN invalid 3 -- ns M19 ENET_CLK to ENET0_TXD[1:0], ENET0_TX_EN valid -- 12 ns M20 ENET0_RXD[1:0], CRS_DV(ENET0_RX_DV), ENET0_RX_ER to ENET_CLK setup 2 -- ns M21 ENET_CLK to ENET0_RXD[1:0], ENET0_RX_DV, ENET0_RX_ER hold 2 -- ns 3.5.5 Coresight ETM9 AC Interface Timing The following timing specifications are given as a guide for a TPA that supports TRACECLK (ETM_TCLK) frequencies up to 80 MHz. TRACECLK is the ETM_TCLK signal which can be made functional by using some IOMUX configurations. See the reference manual for detailed information. 3.5.5.1 TRACECLK Timing This section describes TRACECLK timings. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 37 Electrical Characteristics Figure 14 shows TRACECLK signal timings. Table 43 describes the timing parameters shown in the figure. Figure 14. TRACECLK Signal Timing Diagram Table 43. TRACECLK Signal Timing Characteristic1 ID Min. Max. Unit Tr Clock and data raise time 3 -- ns Tf Clock and data fall time 3 -- ns Twh High pulse wide 2 -- ns Twl Low pulse wide 2 -- ns 12.5 -- ns Tcyc 3.5.5.2 Clock period Trace Data Signal Timing Figure 15 shows the setup and hold requirements of the trace data pins with respect to TRACECLK. Table 44 describes the timing parameters shown in the figure. Figure 15. Trace Data Signal Timing Diagram Table 44. Trace Data Signal Timing Characteristic1 ID Min. Max. Unit Ts Data setup 2 -- ns Th Data hold 2 -- ns i.MX28 Applications Processors for Consumer Products, Rev. 3 38 Freescale Semiconductor Electrical Characteristics 3.5.6 FlexCAN AC Timing Table 45 and Table 46 show voltage requirements for the FlexCAN transceiver Tx and Rx pins. Table 45. Tx Pin Characteristics 1 Parameter Symbol Min. Typ. Max. Unit High-level output voltage VOH 2 -- Vcc1 + 0.3 V Low-level output voltage VOL -- 0.8 -- V Vcc = +3.3 V 5% Table 46. Rx Pin Characteristics 1 Parameter Symbol Min. Typ. Max. Unit High-level input voltage VIH 0.8 x Vcc1 -- Vcc1 V Low-level input voltage VIL -- 0.4 -- V Vcc = +3.3 V 5% Figure 16 through Figure 19 show the FlexCAN timing, including timing of the standby and shutdown signals. VCC/2 TXD VCC/2 tOFFTXD tONTXD 0.9V VDIFF 0.5V tONRXD RXD tOFFRXD VCC/2 VCC/2 Figure 16. FlexCAN Timing Diagram i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 39 Electrical Characteristics VCC x 0.75 RS Bus Externally Driven 1.1V VDIFF tSBRXDL tDRXDL RXD VCC/2 VCC/2 Figure 17. Timing Diagram for FlexCAN Standby Signal SHDN VCC/2 VCC/2 tOFFSHDN tONSHDN VDIFF 0.5V Bus Externally Driven VCC/2 RXD Figure 18. Timing Diagram for FlexCAN Shutdown Signal SHDN VCC/2 tSHDNSB 0.75 x V CC RS Figure 19. Timing Diagram for FlexCAN Shutdown-to-Standby Signal i.MX28 Applications Processors for Consumer Products, Rev. 3 40 Freescale Semiconductor Electrical Characteristics 3.5.7 General-Purpose Media Interface (GPMI) Timing The i.MX28 GPMI controller is a flexible interface NAND Flash controller with 8-bit data width, up to 50MB/s I/O speed and individual chip select. It supports normal timing mode, using two Flash clock cycles for one access of RE and WE. AC timings are provided as multiplications of the clock cycle and fixed delay. Figure 20, Figure 21, Figure 22 and Figure 23 depict the relative timing between GPMI signals at the module level for different operations under normal mode. Table 47 describes the timing parameters (NF1-NF17) that are shown in the figures. CLE NF2 NF1 NF3 NF4 CEn NF5 WE NF6 NF7 ALE NF8 NF9 Command IO[7:0] Figure 20. Command Latch Cycle Timing Diagram CLE NF1 NF4 NF3 CEn NF10 NF11 NF5 WE NF7 NF6 ALE NF8 NF9 IO[7:0] Address Figure 21. Address Latch Cycle Timing Diagram i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 41 Electrical Characteristics CLE NF1 NF3 CEn NF10 NF11 NF5 WE NF7 NF6 ALE NF8 NF9 IO[7:0] Data to NF Figure 22. Write Data Latch Cycle Timing Diagram CLE CEn NF14 NF15 NF13 RE NF16 NF17 RB NF12 IO[7:0] Data from NF Figure 23. Read Data Latch Cycle Timing Diagram i.MX28 Applications Processors for Consumer Products, Rev. 3 42 Freescale Semiconductor Electrical Characteristics Table 47. NFC Timing Parameters1 ID Parameter Symbol Timing T = GPMI Clock Cycle Example Timing for GPMI Clock 100MHz T = 10ns Min. Max. Min. Max. Unit NF1 CLE setup time tCLS (AS+1)*T -- 10 -- ns NF2 CLE hold time tCLH (DH+1)*T -- 20 -- ns NF3 CEn setup time tCS (AS+1)*T -- 10 -- ns NF4 CE hold time tCH (DH+1)*T -- 20 -- ns NF5 WE pulse width tWP NF6 ALE setup time tALS (AS+1)*T -- 10 -- ns NF7 ALE hold time tALH (DH+1)*T -- 20 -- ns NF8 Data setup time tDS DS*T -- 10 -- ns NF9 Data hold time tDH DH*T -- 10 -- ns NF10 Write cycle time tWC (DS+DH)*T 20 ns NF11 WE hold time tWH DH*T 10 ns NF12 Ready to RE low tRR (AS+1)*T -- 10 -- ns NF13 RE pulse width tRP DS*T -- 10 -- ns NF14 READ cycle time tRC (DS+DH)*T -- 20 -- ns NF15 RE high hold time tREH DH*T 10 -- ns NF16 Data setup on read tDSR N/A 10 -- ns NF17 Data hold on read tDHR N/A 10 -- ns DS*T 10 ns 1 The Flash clock maximum frequency is 100 MHz. 2)GPMI's output timing could be controlled by module's internal register, say HW_GPMI_TIMING0_ADDRESS_SETUP,HW_GPMI_TIMING0_DATA_SETUP,HW_GPMI_TIMING0_DATA_HOLD, this AC timing depends on these registers' setting. In the above table we use AS/DS/DH representing these settings each. 3)AS minimum value could be 0, while DS/DH minimum value is 1. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 43 Electrical Characteristics 3.5.8 LCD AC Output Electrical Specifications Figure 24 depicts the AC output timing for the LCD module. Table 48 lists the LCD module timing parameters. T PAD_LCD_DOTCK Falling edge capture tSF tHF tSR tHR PAD_LCD_DOTCK Rising edge capture tDW PAD_LCD_D[17:0], PAD_LCD_VSYNC, etc DATA/CTRL Notes: T = LCD interface clock period I/O Drive Strength = 4mA I/O Voltage = 3.3V Cck = Capacitance load on DOTCK pad Cd = Capacitance load on DATA/CTRL pad Figure 24. LCD AC Output Timing Diagram Table 48. LCD AC Output Timing Parameters ID Parameter Description tSF Data setup for falling edge DOTCK = T/2 - 1.97ns + 0.15*Cck - 0.19*Cd tHF Data hold for falling edge DOTCK = T/2 + 0.29ns + 0.09*Cd - 0.10*Cck tSR Data setup for rising edge DOTCK = T/2 - 2.09ns + 0.18*Cck - 0.19*Cd tHR Data hold for rising edge DOTCK = T/2 + 0.40ns + 0.09*Cd - 0.10*Cck tDW Data valid window tDW = T - 1.45ns i.MX28 Applications Processors for Consumer Products, Rev. 3 44 Freescale Semiconductor Electrical Characteristics 3.5.9 Inter IC (I2C) Timing The I2C module is designed to support up to 400-Kbps I2C connection compliant with I2C bus protocol. The following section describes I2C SDA and SCL signal timings. Figure 25 shows the timing of the I2C module. Table 49 describes the I2C module timing parameters (IC1-IC11) shown in the figure. I2C_SCL IC11 IC10 I2C_SDA IC2 START IC7 IC4 IC8 IC10 IC11 IC6 IC9 IC3 STOP START START IC5 IC1 Figure 25. I2C Module Timing Diagram Table 49. I2C Module Timing Parameters: 1.8 V - 3.6 V Standard Mode ID Fast Mode Parameter Unit Min. Max. Min. Max. IC1 I2C_SCL cycle time 10 -- 2.5 -- s IC2 Hold time (repeated) START condition 4.0 -- 0.6 -- s IC3 Set-up time for STOP condition 4.0 -- 0.6 -- s IC4 Data hold time 01 3.452 01 0.92 s IC5 HIGH Period of I2C_SCL clock 4.0 -- 0.6 -- s IC6 LOW Period of the I2C_SCL clock 4.7 -- 1.3 -- s IC7 Set-up time for a repeated START condition 4.7 -- 0.6 -- s -- ns IC8 Data set-up time 250 -- 1003 IC9 Bus free time between a STOP and START condition 4.7 -- 1.3 -- s 4 300 ns IC10 Rise time of both I2C_SDA and I2C_SCL signals -- 1000 20+0.1Cb IC11 Fall time of both I2C_SDA and I2C_SCL signals -- 300 20+0.1Cb4 300 ns IC12 Capacitive load for each bus line (C b) -- 400 -- 400 pF 1 A device must internally provide a hold time of at least 300 ns for the I2C_SDA signal in order to bridge the undefined region of the falling edge of I2C_SCL. 2 The maximum IC4 has to be met only if the device does not stretch the LOW period (ID no IC5) of the I2C_SCL signal. 3 A fast-mode I2C bus device can be used in a standard-mode I2C bus system, but the requirement of Set-up time (ID No IC7) of 250 ns must then be met. This is automatically the case if the device does not stretch the LOW period of the I2C_SCL signal. If such a device does stretch the LOW period of the I2C_SCL signal, it must output the next data bit to the I2C_SDA line max_rise_time (ID No IC9) + data_setup_time (ID No IC7) = 1000 + 250 = 1250 ns (according to the standard-mode I2C bus specification) before the I2C_SCL line is released. 4 C = total capacitance of one bus line in pF. b i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 45 Electrical Characteristics 3.5.10 JTAG Interface Timing Figure 26 through Figure 29 show respectively the test clock input, boundary scan, test access port, and TRST timings for the SJC. Table 50 describes the SJC timing parameters (SJ1-SJ13) indicated in the figures. SJ1 SJ2 TCK (Input) SJ2 VM VIH VM VIL SJ3 SJ3 Figure 26. Test Clock Input Timing Diagram TCK (Input) VIH VIL SJ4 Data Inputs SJ5 Input Data Valid SJ6 Data Outputs Output Data Valid SJ7 Data Outputs SJ6 Data Outputs Output Data Valid Figure 27. Boundary Scan (JTAG) Timing Diagram i.MX28 Applications Processors for Consumer Products, Rev. 3 46 Freescale Semiconductor Electrical Characteristics TCK (Input) VIH VIL SJ8 TDI TMS (Input) SJ9 Input Data Valid SJ10 TDO (Output) Output Data Valid SJ11 TDO (Output) SJ10 TDO (Output) Output Data Valid Figure 28. Test Access Port Timing Diagram TCK (Input) SJ13 TRST (Input) SJ12 Figure 29. TRST Timing Diagram Table 50. SJC Timing Parameters All Frequencies ID Parameter Unit Min. Max. SJ1 TCK cycle time 100 -- ns SJ2 TCK clock pulse width measured at VM1 40 -- ns SJ3 TCK rise and fall times -- 3 ns SJ4 Boundary scan input data set-up time 10 -- ns SJ5 Boundary scan input data hold time 50 -- ns SJ6 TCK low to output data valid -- 50 ns SJ7 TCK low to output high impedance -- 50 ns SJ8 TMS, TDI data set-up time 10 -- ns SJ9 TMS, TDI data hold time 50 -- ns i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 47 Electrical Characteristics Table 50. SJC Timing Parameters (continued) All Frequencies ID 1 Parameter Unit Min. Max. SJ10 TCK low to TDO data valid -- 44 ns SJ11 TCK low to TDO high impedance -- 44 ns SJ12 TRST assert time 100 -- ns SJ13 TRST set-up time to TCK low 40 -- ns VM - mid point voltage 3.5.11 Pulse Width Modulator (PWM) Timing Figure 30 depicts the timing of the PWM, and Table 51 lists the PWM timing characteristics. The PWM can be programmed to select one of two clock signals as its source frequency: xtal clock or hsadc clock. The selected clock signal is passed through a prescaler before being input to the counter. The output is available at the pulse width modulator output (PWMO) external pin. PWM also supports MATT mode. In this mode, it can be programmed to select one of two clock signals as its source frequency, 24-MHz or 32-kHz crystal clock. For a 32-kHz source clock input, the PWM outputs the 32-kHz clock directly to PAD. 1 2a 3b PWM Source Clock 2b 4b 3a 4a PWM Output Figure 30. PWM Timing Table 51. PWM Output Timing Parameter: Xtal clock 1 Ref No. Parameter Minimum Maximum Unit 1 System CLK frequency1 0 24MHz MHz 2a Clock high time 21 -- ns 2b Clock low time 21 -- ns 3a Clock fall time -- 0.3 ns 3b Clock rise time -- 0.3 ns 4a Output delay time -- 15.08 ns 4b Output setup time 15.77 -- ns CL of PWMO = 30 pF i.MX28 Applications Processors for Consumer Products, Rev. 3 48 Freescale Semiconductor Electrical Characteristics 1 2a 3b PWM Source Clock 2b 4b 3a 4a PWM Output Figure 31. PWM Timing Table 52. PWM Output Timing Parameter: HSADC clock 1 Ref No. Parameter Minimum Maximum Unit 1 System CLK frequency1 0 32 MHz 2a Clock high time 6.813 -- ns 2b Clock low time 24.432 -- ns 3a Clock fall time -- 0.3 ns 3b Clock rise time -- 0.3 ns 4a Output delay time -- 14.93 ns 4b Output setup time 15.71 -- ns CL of PWMO = 30 pF 2a PWM Source Clock 4a 3a 2b 3b 4b PWM Output Figure 32. PWM Timing i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 49 Electrical Characteristics Table 53. PWM Output Timing Parameter: MATT Mode 24 MHz Crystal Clock 1 Ref No. Parameter Minimum Maximum Unit 1 System CLK frequency1 24 24 MHz 2a Clock high time 20.99 -- ns 2b Clock low time 21.01 -- ns 3a Clock fall time -- 0.3 ns 3b Clock rise time -- 0.3 ns 4a Output delay time -- 15.23 ns 4b Output setup time 15.92 -- ns CL of PWMO = 30 pF 3.5.12 Serial Audio Interface (SAIF) AC Timing The following subsections describe SAIF timing in two cases: * Transmitter * Receiver 3.5.12.1 SAIF Transmitter Timing Figure 33 shows the timing for SAIF transmitter with internal clock, and Table 54 describes the timing parameters (SS1-SS13). SS1 SS5 SS2 SS3 SS4 BITCLK SS6 LRCLK SS7 SS8 SS11 SS9 SDATA0-2 SS10 SS13 SS12 Figure 33. SAIF Transmitter Timing Diagram i.MX28 Applications Processors for Consumer Products, Rev. 3 50 Freescale Semiconductor Electrical Characteristics Table 54. SAIF Transmitter Timing ID Parameter Min. Max. Unit SS1 BITCLK period 81.4 -- ns SS2 BITCLK high period 36.0 -- ns SS3 BITCLK rise time -- 6.0 ns SS4 BITCLK low period 36.0 -- ns SS5 BITCLK fall time -- 6.0 ns SS6 BITCLK high to LRCLK high -- 15.0 ns SS7 BITCLK high to LRCLK low -- 15.0 ns SS8 LRCLK rise time -- 6.0 ns SS9 LRCLK fall time -- 6.0 ns SS10 BITCLK high to SDATA valid from high impedance -- 15.0 ns SS11 BITCLK high to SDATA high/low -- 15.0 ns SS12 BITCLK high to SDATA high impedance -- 15.0 ns SS13 SDATA rise/fall time -- 6.0 ns 3.5.12.2 SAIF Receiver Timing Figure 34 shows the timing for the SAIF receiver with internal clock. Table 55 describes the timing parameters (SS1-SS17) shown in the figure. SS1 SS3 SS5 SS2 SS4 BITCLK SS14 SS15 LRCLK SS16 SS17 SDATA0-2 Figure 34. SAIF Receiver Timing Diagram i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 51 Electrical Characteristics Table 55. SAIF Receiver Timing with Internal Clock ID Parameter Min. Max. Unit SS1 BITCLK period 81.4 -- ns SS2 BITCLK high period 36.0 -- ns SS3 BITCLK rise time -- 6.0 ns SS4 BITCLK low period 36.0 -- ns SS5 BITCLK fall time -- 6.0 ns SS14 BITCLK high to LRCLK high -- 15.0 ns SS15 BITCLK high to LRCLK low -- 15.0 ns SS16 SDATA setup time before BITCLK high 10.0 -- ns SS17 SDATA hold time after BITCLK high 0.0 -- ns 3.5.13 SPDIF AC Timing SPDIF data is sent using bi-phase marking code. When encoding, the SPDIF data signal is modulated by a clock that is twice the bit rate of the data signal. The following Table 56 shows SPDIF timing parameters, including the timing of the modulating Tx clock (spdif_clk) in SPDIF transmitter as shown in the Figure 35. Table 56. SPDIF Timing Timing Parameter Range Characteristics Symbol Unit Min Max -- -- -- 1.5 13.6 18.0 spclkp 81.4 -- ns spdif_clk high period spclkph 65.1 -- ns spdif_clk low period spclkpl 65.1 -- ns SPDIFOUT output (Load = 30pf) * Skew * Transition Rising * Transition Falling ns -- -- -- Modulating Tx clock (spdif_clk) period spclkp spclkpl spclkph spdif_clk (Input) Figure 35. spdif_clk Timing i.MX28 Applications Processors for Consumer Products, Rev. 3 52 Freescale Semiconductor Electrical Characteristics 3.5.14 Synchronous Serial Port (SSP) AC Timing This section describes the electrical information of the SSP, which includes SD/MMC4.3 (Single Data Rate) timing, MMC4.4 (Dual Date Rate) timing, MS (Memory Stick) timing, and SPI timing. 3.5.14.1 SD/MMC4.3 (Single Data Rate) AC Timing Figure 36 depicts the timing of SD/MMC4.3, and Table 57 lists the SD/MMC4.3 timing characteristics. SD4 SD2 SD1 SD5 SCK SD3 output from SSP to card CMD DAT0 DAT1 ...... DAT7 SD6 SD7 input from card to SSP SD8 CMD DAT0 DAT1 ...... DAT7 Figure 36. SD/MMC4.3 Timing Table 57. SD/MMC4.3 Interface Timing Specification ID Parameter Symbols Min Max Unit Clock Frequency (Low Speed) fPP1 0 400 kHz Clock Frequency (SD/SDIO Full Speed/High Speed) fPP2 0 25/50 MHz Clock Frequency (MMC Full Speed/High Speed) fPP3 0 20/52 MHz Clock Frequency (Identification Mode) fOD 100 400 kHz SD2 Clock Low Time tWL 7 -- ns SD3 Clock High Time tWH 7 -- ns SD4 Clock Rise Time tTLH -- 3 ns SD5 Clock Fall Time tTHL -- 3 ns tOD -5 5 ns Card Input Clock SD1 SSP Output / Card Inputs CMD, DAT (Reference to CLK) SD6 SSP Output Delay SSP Input / Card Outputs CMD, DAT (Reference to CLK) i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 53 Electrical Characteristics Table 57. SD/MMC4.3 Interface Timing Specification (continued) ID Parameter Symbols Min Max Unit SD7 SSP Input Setup Time tISU 2.5 -- ns SD8 SSP Input Hold Time tIH4 2.5 -- ns 1 In low speed mode, the card clock must be lower than 400 kHz, and the voltage ranges from 2.7 to 3.6 V. In normal speed mode for the SD/SDIO card, clock frequency can be any value between 0 ~ 25 MHz. In high speed mode, clock frequency can be any value between 0 ~ 50 MHz. 3 In normal speed mode for MMC card, clock frequency can be any value between 0 ~ 20 MHz. In high speed mode, clock frequency can be any value between 0 ~ 52MHz. 4 To satisfy hold timing, the delay difference between clock input and cmd/data input must not exceed 2ns. 2 3.5.14.2 MMC4.4 (Dual Data Rate) AC Timing Figure 37 depicts the timing of MMC4.4, and Table 58 lists the MMC4.4 timing characteristics. Be aware that only DATA0-DATA7 are sampled on both edges of the clock (not applicable to CMD). SD1 SCK output from SSP to card DAT0 DAT1 ...... DAT7 SD2 SD2 ...... SD3 SD4 DAT0 DAT1 ...... DAT7 input from card to SSP ...... Figure 37. MMC4.4 Timing Table 58. MMC4.4 Interface Timing Specification ID Parameter Symbols Min Max Unit Clock Frequency (MMC Full Speed/High Speed) fPP 0 52 MHz tOD -5 5 ns Card Input Clock SD1 SSP Output / Card Inputs CMD, DAT (Reference to CLK) SD2 SSP Output Delay SSP Input / Card Outputs CMD, DAT (Reference to CLK) SD3 SSP Input Setup Time tISU 2.5 -- ns SD4 SSP Input Hold Time tIH 2.5 -- ns i.MX28 Applications Processors for Consumer Products, Rev. 3 54 Freescale Semiconductor Electrical Characteristics 3.5.14.3 MS (Memory Stick) AC Timing The SSP module, which also has the function of a memory stick host controller, is compatible with the Sony Memory Stick version 1.x and Memory Stick PRO. Figure 38, Figure 39 and Table 40 show the timing of the Memory Stick. Table 59 and Table 60 list the Memory Stick timing characteristics. MS1 80% 50% 20% 80% 50% 20% SCK MS2 80% 50% 20% MS3 MS5 MS4 Figure 38. MS Clock Time Waveforms MS1 SCK BS(CMD) MS6 MS7 MS9 MS8 DATA (Output) MS10 DATA (Input) Figure 39. MS Serial Transfer Mode Timing Diagram i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 55 Electrical Characteristics MS1 SCK BS(CMD) MS11 MS12 MS13 MS14 DATA (Output) MS15 DATA (Input) Figure 40. MS Parallel Transfer Mode Timing Diagram Table 59. MS Serial Transfer Timing Parameters ID Parameter Symbol Min Max Unit MS1 SCK Cycle Time tCLKc 50 -- ns MS2 SCK High Pulse Time tCLKwh 15 -- ns MS3 SCK Low Pulse Time tCLKwl 15 -- ns MS4 SCK Rise Time tCLKr -- 10 ns MS5 SCK Fall Time tCLKf -- 10 ns MS6 BS Setup Time tBSsu 5 -- ns MS7 BS Hold Time tBSh 5 -- ns MS8 DATA Setup Time tDsu 5 -- ns MS9 DATA Hold Time tDh 5 -- ns MS10 DATA Input Delay Time tDd -- 15 ns Table 60. MS Parallel Transfer Timing Parameters ID Parameter Symbol Min Max Unit MS1 SCK Cycle Time tCLKc 25 -- ns MS2 SCK High Pulse Time tCLKwh 5 -- ns MS3 SCK Low Pulse Time tCLKwl 5 -- ns MS4 SCK Rise Time tCLKr -- 10 ns i.MX28 Applications Processors for Consumer Products, Rev. 3 56 Freescale Semiconductor Electrical Characteristics Table 60. MS Parallel Transfer Timing Parameters (continued) ID Parameter Symbol Min Max Unit MS5 SCK Fall Time tCLKf -- 10 ns MS11 BS Setup Time tBSsu 8 -- ns MS12 BS Hold Time tBSh 1 -- ns MS13 DATA Setup Time tDsu 8 -- ns MS14 DATA Hold Time tDh 1 -- ns MS15 DATA Input Delay Time tDd -- 15 ns 3.5.14.4 SPI AC Timing Figure 41 depicts the master mode and slave mode timings of the SPI, and Table 61 lists the timing parameters. SSn CS1 CS3 CS2 CS5 CS6 CS4 SCK CS9 CS3 CS10 CS2 MISO CS8 CS7 MOSI Figure 41. SPI Interface Timing Diagram Table 61. SPI Interface Timing Parameters ID Parameter Symbol Min. Max. Unit CS1 SCK cycle time tclk 50 -- ns CS2 SCK high or low time tSW 25 -- ns CS3 SCK rise or fall tRISE/FALL -- 7.6 ns CS4 SSn pulse width tCSLH 25 -- ns CS5 SSn lead time (CS setup time) tSCS 25 -- ns CS6 SSn lag time (CS hold time) tHCS 25 -- ns CS7 MOSI setup time tSmosi 5 -- ns CS8 MOSI hold time tHmosi 5 -- ns CS9 MISO setup time tSmiso 5 -- ns CS10 MISO hold time tHmiso 5 -- ns i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 57 Electrical Characteristics 3.5.15 UART (UARTAPP and DebugUART) AC Timing This section describes the UART module AC timing which is applicable to both UARTAPP and DebugUART. 3.5.15.1 UART Transmit Timing Figure 39 shows the UART transmit timing, showing only eight data bits and one stop bit. Table 62 describes the timing parameter (UA1) shown in the figure. UA1 TXD (output) Start Bit Possible Parity Bit UA1 Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Par Bit STOP BIT UA1 Next Start Bit UA1 Figure 42. UART Transmit Timing Diagram Table 62. UART Transmit Timing Parameters ID Parameter Symbol Min. Max. Unit UA1 Transmit Bit Time tTbit 1/Fbaud_rate1 - Tref_clk2 1/Fbaud_rate + Tref_clk -- 1 Fbaud_rate: Baud rate frequency. The maximum baud rate the UARTAPP can support is 3.25 Mbps. The maximum baud rate of DebugUART is 115.2 kbps. 2 T ref_clk: The period of UART reference clock ref_clk (which is APBX clock = 24 MHz). 3.5.15.2 UART Receive Timing Figure 43 shows the UART receive timing, showing only eight data bits and one stop bit. Table 63 describes the timing parameter (UA2) shown in the figure. - UA2 RXD (input) Start Bit Possible Parity Bit UA2 Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Par Bit STOP BIT UA2 Next Start Bit UA2 Figure 43. UART Receive Timing Diagram i.MX28 Applications Processors for Consumer Products, Rev. 3 58 Freescale Semiconductor Package Information and Contact Assignments Table 63. UART Receive Timing Parameters ID Parameter Symbol UA2 Receive bit time1 tRbit Min. Max. 1/Fbaud_rate2 - 1/(16 1/F baud_rate + 1/(16 x F baud_rate) x Fbaud_rate) Unit -- 1 The UART receiver can tolerate 1/(16 x Fbaud_rate) tolerance in each bit. But accumulation tolerance in one frame must not exceed 3/(16 x Fbaud_rate). 2 Fbaud_rate: Baud rate frequency. The maximum baud rate the UARTAPP can support is 3.25 Mbps. The maximum baud rate of DebugUART is 115 kbps. 4 4.1 Package Information and Contact Assignments Case MAPBGA-289, 14 x 14 mm, 0.8 mm Pitch The following notes apply to Figure 44: * All dimensions are in millimeters. * Dimensioning and tolerancing per ASME Y14.5M-1994. * Maximum solder bump diameter measured parallel to datum A. * Datum A, the seating plane, is determined by the spherical crowns of the solder bumps. * Parallelism measurement excludes any effect of mark on top surface of package. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 59 Package Information and Contact Assignments Figure 44 shows the i.MX28 production package. Figure 44. i.MX28 Production Package zzxz 4.2 Ground, Power, Sense, and Reference Contact Assignments Table 64 shows power and ground contact assignments for the MAPBGA package. Table 64. MAPBGA Power and Ground Contact Assignments Contact Name Contact Assignment VDDA1 C13 VDDD G12,G11,F10,F11,K12,F12,G10 VDDIO18 G8,F9,F8,G9 VDDIO33 H8,J8,N3,G3,E6,J9,J10,A7,E16 VDDIO33_EMI N17 VDDIO_EMI P11,R13,N13,N15,G17,M12,M10,G13,M11,L13,G15 i.MX28 Applications Processors for Consumer Products, Rev. 3 60 Freescale Semiconductor Package Information and Contact Assignments Table 64. MAPBGA Power and Ground Contact Assignments (continued) Contact Name Contact Assignment VDDIO_EMIQ K15,J13,R15 VDDXTAL C12 VSS E15,L11,A1,K10,K11,J11,M14,H11,U1,H9,H12,H3,K9,C16,L10,H16,J12,H10,B7,E5,J15,A9,N4 VSSA1 B13 VSSA2 B11 VSSIO_EMI F16,R10,H14,M16,F14,L12,P16,U17,T14,P14,R12 4.3 Signal Contact Assignments Table 65 lists the i.MX287 MAPBGA package signal contact assignments. Table 65. i.MX287 MAPBGA Contact Assignments Signal Name Contact Assignment Signal Name Contact Assignment Signal Name Contact Assignment AUART0_CTS J6 EMI_DQS1N J16 LCD_D17 R3 AUART0_RTS J7 EMI_ODT0 R17 LCD_D18 U4 AUART0_RX G5 EMI_ODT1 T17 LCD_D19 T4 AUART0_TX H5 EMI_RASN R16 LCD_D20 R4 AUART1_CTS K5 EMI_VREF0 R14 LCD_D21 U5 AUART1_RTS J5 EMI_VREF1 K13 LCD_D22 T5 AUART1_RX L4 EMI_WEN T15 LCD_D23 R5 AUART1_TX K4 ENET0_COL J4 LCD_DOTCLK N1 AUART2_CTS H6 ENET0_CRS J3 LCD_ENABLE N5 AUART2_RTS H7 ENET0_MDC G4 LCD_HSYNC M1 AUART2_RX F6 ENET0_MDIO H4 LCD_RD_E P4 AUART2_TX F5 ENET0_RXD0 H1 LCD_RESET M6 AUART3_CTS L6 ENET0_RXD1 H2 LCD_RS M4 AUART3_RTS K6 ENET0_RXD2 J1 LCD_VSYNC L1 AUART3_RX M5 ENET0_RXD3 J2 LCD_WR_RWN K1 AUART3_TX L5 ENET0_RX_CLK F3 LRADC0 C15 BATTERY A15 ENET0_RX_EN E4 LRADC1 C9 DCDC_BATT B15 ENET0_TXD0 F1 LRADC2 C8 DCDC_GND A17 ENET0_TXD1 F2 LRADC3 D9 DCDC_LN1 B17 ENET0_TXD2 G1 LRADC4 D13 DCDC_LP A16 ENET0_TXD3 G2 LRADC5 D15 i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 61 Package Information and Contact Assignments Table 65. i.MX287 MAPBGA Contact Assignments (continued) Signal Name Contact Assignment Signal Name Contact Assignment Signal Name Contact Assignment DCDC_VDDA B16 ENET0_TX_CLK E3 LRADC6 C14 DCDC_VDDD D17 ENET0_TX_EN F4 PSWITCH A11 DCDC_VDDIO C17 ENET_CLK E2 PWM0 K7 DEBUG B9 GPMI_ALE P6 PWM1 L7 EMI_A00 U15 GPMI_CE0N N7 PWM2 K8 EMI_A01 U12 GPMI_CE1N N9 PWM3 E9 EMI_A02 U14 GPMI_CE2N M7 PWM4 E10 EMI_A03 T11 GPMI_CE3N M9 RESETN A14 EMI_A04 U10 GPMI_CLE P7 RTC_XTALI D11 EMI_A05 R11 GPMI_D00 U8 RTC_XTALO C11 EMI_A06 R9 GPMI_D01 T8 SAIF0_BITCLK F7 EMI_A07 N11 GPMI_D02 R8 SAIF0_LRCLK G6 EMI_A08 U9 GPMI_D03 U7 SAIF0_MCLK G7 EMI_A09 P10 GPMI_D04 T7 SAIF0_SDATA0 E7 EMI_A10 U13 GPMI_D05 R7 SAIF1_SDATA0 E8 EMI_A11 T10 GPMI_D06 U6 SPDIF D7 EMI_A12 U11 GPMI_D07 T6 SSP0_CMD A4 EMI_A13 T9 GPMI_RDN R6 SSP0_DATA0 B6 EMI_A14 N10 GPMI_RDY0 N6 SSP0_DATA1 C6 EMI_BA0 T16 GPMI_RDY1 N8 SSP0_DATA2 D6 EMI_BA1 T12 GPMI_RDY2 M8 SSP0_DATA3 A5 EMI_BA2 N12 GPMI_RDY3 L8 SSP0_DATA4 B5 EMI_CASN U16 GPMI_RESETN L9 SSP0_DATA5 C5 EMI_CE0N P12 GPMI_WRN P8 SSP0_DATA6 D5 EMI_CE1N P9 HSADC0 B14 SSP0_DATA7 B4 EMI_CKE T13 I2C0_SCL C7 SSP0_DETECT D10 EMI_CLK L17 I2C0_SDA D8 SSP0_SCK A6 EMI_CLKN L16 JTAG_RTCK E14 SSP1_CMD C1 EMI_D00 N16 JTAG_TCK E11 SSP1_DATA0 D1 EMI_D01 M13 JTAG_TDI E12 SSP1_DATA3 E1 EMI_D02 P15 JTAG_TDO E13 SSP1_SCK B1 EMI_D03 N14 JTAG_TMS D12 SSP2_MISO B3 i.MX28 Applications Processors for Consumer Products, Rev. 3 62 Freescale Semiconductor Package Information and Contact Assignments Table 65. i.MX287 MAPBGA Contact Assignments (continued) Signal Name Contact Assignment Contact Assignment Signal Name Contact Assignment Signal Name EMI_D04 P13 JTAG_TRST D14 SSP2_MOSI C3 EMI_D05 P17 LCD_CS P5 SSP2_SCK A3 EMI_D06 L14 LCD_D00 K2 SSP2_SS0 C4 EMI_D07 M17 LCD_D01 K3 SSP2_SS1 D3 EMI_D08 G16 LCD_D02 L2 SSP2_SS2 D4 EMI_D09 H15 LCD_D03 L3 SSP3_MISO B2 EMI_D10 G14 LCD_D04 M2 SSP3_MOSI C2 EMI_D11 J14 LCD_D05 M3 SSP3_SCK A2 EMI_D12 H13 LCD_D06 N2 SSP3_SS0 D2 EMI_D13 H17 LCD_D07 P1 TESTMODE C10 EMI_D14 F13 LCD_D08 P2 USB0DM A10 EMI_D15 F17 LCD_D09 P3 USB0DP B10 EMI_DDR_OPE N K14 LCD_D10 R1 USB1DM B8 EMI_DDR_OPE N_FB L15 LCD_D11 R2 USB1DP A8 EMI_DQM0 M15 LCD_D12 T1 VDD1P5 D16 EMI_DQM1 F15 LCD_D13 T2 VDD4P2 A13 EMI_DQS0 K17 LCD_D14 U2 VDD5V E17 EMI_DQS0N K16 LCD_D15 U3 XTALI A12 EMI_DQS1 J17 LCD_D16 T3 XTALO B12 4.4 i.MX280 Ball Map Table 66 shows the i.MX280 MAPBGA ball map. A DCDC_GND 17 16 DCDC_LP 15 BATTERY 14 RESETN 13 VDD4P2 12 XTALI 11 PSWITCH 10 USB0DM 9 VSS 8 USB1DP 7 VDDIO33 6 SSP0_SCK SSP0_DATA3 5 4 SSP0_CMD 3 SSP2_SCK 2 NC VSS A 1 Table 66. 289-Pin i.MX280 MAPBGA Ball Map i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 63 64 VDDIO33 VDDIO33 VDDIO33 VSS VSS VDDIO_EMIQ EMI_D11 PWM2 VSS VSS VSS VDDD EMI_VREF1 EMI_DDR_OPEN J AUART0_RTS PWM0 K AUART0_CTS NC EMI_DQS1 NC NC EMI_DQS0 NC AUART1_TX EMI_DQS1N NC ETM_DA1 EMI_DQS0N NC ETM_DA0 VSS NC ETM_TCLK VDDIO_EMIQ J K NC VDDIO33 NC ENET_CLK NC E H EMI_D13 VSS EMI_D09 VSSIO_EMI EMI_D12 VSS VSS VSS VSS VDDIO33 NC NC AUART0_TX NC SAIF0_LRCLK VDDIO33 VSS F G VSSIO_EMI EMI_D10 EMI_D15 EMI_D14 VDDIO_EMI VDDIO_EMI VDDD VDDD VSSIO_EMI VDDD VDDD EMI_D08 VDDD VDDD EMI_DQM1 VDDIO18 VDDIO18 VDDIO_EMI VDDIO18 VDDIO18 E VDD5V VDDIO33 VSS JTAG_RTCK JTAG_TDO JTAG_TDI JTAG_TCK PWM4 PWM3 SAIF1_SDATA0 SAIF0_MCLK SAIF0_BITCLK SAIF0_SDATA0 NC AUART0_RX ENET0_MDIO ENET0_MDC ENET0_TX_EN ENET0_RX_EN VSS ENET0_TXD1 NC ENET0_RXD1 ENET0_TXD0 NC ENET0_RXD0 F G H D DCDC_VDDD VDD1P5 LRADC5 JTAG_TRST LRADC4 JTAG_TMS RTC_XTALI SSP0_DETECT LRADC3 I2C0_SDA NC SSP0_DATA2 SSP0_DATA6 SSP2_SS2 SSP2_SS1 NC NC D C DCDC_VDDIO VSS LRADC0 LRADC6 VDDA1 VDDXTAL RTC_XTALO TESTMODE LRADC1 LRADC2 I2C0_SCL SSP0_DATA1 SSP0_DATA5 SSP2_SS0 SSP2_MOSI NC NC C B DCDC_LN1 DCDC_VDDA DCDC_BATT HSADC0 VSSA1 XTALO VSSA2 USB0DP DEBUG USB1DM VSS SSP0_DATA0 SSP0_DATA4 SSP0_DATA7 SSP2_MISO NC NC B Package Information and Contact Assignments Table 66. 289-Pin i.MX280 MAPBGA Ball Map (continued) i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor Freescale Semiconductor 4 3 16 15 14 13 12 11 10 9 8 7 6 A DCDC_GND 17 DCDC_LP BATTERY RESETN VDD4P2 XTALI PSWITCH USB0DM VSS USB1DP VDDIO33 SSP0_SCK SSP0_DATA3 5 SSP0_CMD SSP2_SCK 2 1 4.5 NC VSS A EMI_A11 EMI_A04 T EMI_ODT0 17 VSSIO_EMI EMI_ODT1 U EMI_RASN EMI_BA0 16 EMI_CASN R VDDIO_EMIQ EMI_WEN 15 EMI_VREF0 VDDIO_EMI VSSIO_EMI EMI_A00 EMI_CKE EMI_BA1 EMI_A05 VSSIO_EMI EMI_A06 GPMI_D02 GPMI_D05 GPMI_RDN NC NC NC NC NC VSSIO_EMI EMI_A10 EMI_A01 EMI_A03 EMI_A13 EMI_A08 EMI_A12 GPMI_D01 GPMI_D00 GPMI_D04 NC NC GPMI_D03 NC NC GPMI_D07 NC NC GPMI_D06 NC NC NC VSS R EMI_A02 14 13 12 11 10 9 8 7 6 5 4 3 2 1 T U P EMI_D05 VSSIO_EMI EMI_D02 VSSIO_EMI EMI_D04 EMI_CE0N VDDIO_EMI EMI_A09 EMI_CE1N GPMI_WRN GPMI_CLE GPMI_ALE NC ETM_TCTL NC NC ETM_DA7 P N VDDIO33_EMI EMI_D00 VDDIO_EMI EMI_D03 VDDIO_EMI EMI_BA2 EMI_A07 EMI_A14 GPMI_CE1N GPMI_RDY1 GPMI_CE0N GPMI_RDY0 NC VSS VDDIO33 ETM_DA6 NC N M EMI_D07 VSSIO_EMI EMI_DQM0 VSS EMI_D01 VDDIO_EMI VDDIO_EMI VDDIO_EMI NC NC NC NC NC GPIO_B1P26 ETM_DA5 ETM_DA4 NC M L EMI_CLK EMI_CLKN EMI_DDR_OPEN_FB EMI_D06 VDDIO_EMI VSSIO_EMI VSS VSS GPMI_RESETN NC PWM1 NC NC AUART1_RX ETM_DA3 ETM_DA2 NC L Package Information and Contact Assignments Table 66. 289-Pin i.MX280 MAPBGA Ball Map (continued) i.MX283 Ball Map Table 67 shows the i.MX283 MAPBGA ball map. Table 67. 289-Pin i.MX283 MAPBGA Ball Map i.MX28 Applications Processors for Consumer Products, Rev. 3 65 66 VDDIO33 VDDIO33 VDDIO33 VSS VSS VDDIO_EMIQ EMI_D11 PWM2 VSS VSS VSS VDDD EMI_VREF1 EMI_DDR_OPEN J AUART0_RTS PWM0 K AUART0_CTS NC EMI_DQS1 NC NC EMI_DQS0 NC AUART1_TX EMI_DQS1N NC LCD_D01 EMI_DQS0N NC LCD_D00 VSS NC LCD_WR_RWN VDDIO_EMIQ J K NC VDDIO33 NC ENET_CLK NC E H EMI_D13 VSS EMI_D09 VSSIO_EMI EMI_D12 VSS VSS VSS VSS VDDIO33 NC NC AUART0_TX NC SAIF0_LRCLK VDDIO33 VSS F G VSSIO_EMI EMI_D10 EMI_D15 EMI_D14 VDDIO_EMI VDDIO_EMI VDDD VDDD VSSIO_EMI VDDD VDDD EMI_D08 VDDD VDDD EMI_DQM1 VDDIO18 VDDIO18 VDDIO_EMI VDDIO18 VDDIO18 E VDD5V VDDIO33 VSS JTAG_RTCK JTAG_TDO JTAG_TDI JTAG_TCK PWM4 PWM3 SAIF1_SDATA0 SAIF0_MCLK SAIF0_BITCLK SAIF0_SDATA0 NC AUART0_RX ENET0_MDIO ENET0_MDC ENET0_TX_EN ENET0_RX_EN VSS ENET0_TXD1 NC ENET0_RXD1 ENET0_TXD0 NC ENET0_RXD0 F G H D DCDC_VDDD VDD1P5 LRADC5 JTAG_TRST LRADC4 JTAG_TMS RTC_XTALI SSP0_DETECT LRADC3 I2C0_SDA NC SSP0_DATA2 SSP0_DATA6 SSP2_SS2 SSP2_SS1 NC NC D C DCDC_VDDIO VSS LRADC0 LRADC6 VDDA1 VDDXTAL RTC_XTALO TESTMODE LRADC1 LRADC2 I2C0_SCL SSP0_DATA1 SSP0_DATA5 SSP2_SS0 SSP2_MOSI NC NC C B DCDC_LN1 DCDC_VDDA DCDC_BATT HSADC0 VSSA1 XTALO VSSA2 USB0DP DEBUG USB1DM VSS SSP0_DATA0 SSP0_DATA4 SSP0_DATA7 SSP2_MISO NC NC B Package Information and Contact Assignments Table 67. 289-Pin i.MX283 MAPBGA Ball Map (continued) i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor Freescale Semiconductor 16 15 14 13 12 11 10 9 8 7 6 5 4 3 A DCDC_GND 17 DCDC_LP BATTERY RESETN VDD4P2 XTALI PSWITCH USB0DM VSS USB1DP VDDIO33 SSP0_SCK SSP0_DATA3 SSP0_CMD SSP2_SCK 2 1 4.6 NC VSS A EMI_A11 EMI_A04 T EMI_ODT0 17 VSSIO_EMI EMI_ODT1 U EMI_RASN EMI_BA0 16 EMI_CASN R VDDIO_EMIQ EMI_WEN 15 EMI_VREF0 VDDIO_EMI VSSIO_EMI EMI_A00 EMI_CKE EMI_BA1 EMI_A05 VSSIO_EMI EMI_A06 GPMI_D02 GPMI_D05 GPMI_RDN LCD_D23 LCD_D20 LCD_D17 LCD_D11 LCD_D10 VSSIO_EMI EMI_A10 EMI_A01 EMI_A03 EMI_A13 EMI_A08 EMI_A12 GPMI_D01 GPMI_D00 GPMI_D04 LCD_D22 LCD_D21 GPMI_D03 LCD_D19 LCD_D18 GPMI_D07 LCD_D16 LCD_D15 GPMI_D06 LCD_D13 LCD_D14 LCD_D12 VSS R EMI_A02 14 13 12 11 10 9 8 7 6 5 4 3 2 1 T U P EMI_D05 VSSIO_EMI EMI_D02 VSSIO_EMI EMI_D04 EMI_CE0N VDDIO_EMI EMI_A09 EMI_CE1N GPMI_WRN GPMI_CLE GPMI_ALE LCD_CS LCD_RD_E LCD_D09 LCD_D08 LCD_D07 P N VDDIO33_EMI EMI_D00 VDDIO_EMI EMI_D03 VDDIO_EMI EMI_BA2 EMI_A07 EMI_A14 GPMI_CE1N GPMI_RDY1 GPMI_CE0N GPMI_RDY0 NC VSS VDDIO33 LCD_D06 NC N M EMI_D07 VSSIO_EMI EMI_DQM0 VSS EMI_D01 VDDIO_EMI VDDIO_EMI VDDIO_EMI NC NC NC LCD_RESET NC LCD_RS LCD_D05 LCD_D04 NC M L EMI_CLK EMI_CLKN EMI_DDR_OPEN_FB EMI_D06 VDDIO_EMI VSSIO_EMI VSS VSS GPMI_RESETN NC PWM1 NC NC AUART1_RX LCD_D03 LCD_D02 NC L Package Information and Contact Assignments Table 67. 289-Pin i.MX283 MAPBGA Ball Map (continued) i.MX286 Ball Map Table 68 shows the i.MX286 MAPBGA ball map. Table 68. 289-Pin i.MX286 MAPBGA Ball Map i.MX28 Applications Processors for Consumer Products, Rev. 3 67 68 VDDIO33 VDDIO33 VDDIO33 VSS VSS VDDIO_EMIQ EMI_D11 PWM2 VSS VSS VSS VDDD EMI_VREF1 EMI_DDR_OPEN J AUART0_RTS PWM0 K AUART0_CTS NC EMI_DQS1 NC NC EMI_DQS0 NC AUART1_TX EMI_DQS1N NC LCD_D01 EMI_DQS0N NC LCD_D00 VSS NC LCD_WR_RWN VDDIO_EMIQ J K NC VDDIO33 NC ENET_CLK NC E H EMI_D13 VSS EMI_D09 VSSIO_EMI EMI_D12 VSS VSS VSS VSS VDDIO33 NC NC AUART0_TX NC SAIF0_LRCLK VDDIO33 VSS F G VSSIO_EMI EMI_D10 EMI_D15 EMI_D14 VDDIO_EMI VDDIO_EMI VDDD VDDD VSSIO_EMI VDDD VDDD EMI_D08 VDDD VDDD EMI_DQM1 VDDIO18 VDDIO18 VDDIO_EMI VDDIO18 VDDIO18 E VDD5V VDDIO33 VSS JTAG_RTCK JTAG_TDO JTAG_TDI JTAG_TCK PWM4 PWM3 SAIF1_SDATA0 SAIF0_MCLK SAIF0_BITCLK SAIF0_SDATA0 NC AUART0_RX ENET0_MDIO ENET0_MDC ENET0_TX_EN ENET0_RX_EN VSS ENET0_TXD1 NC ENET0_RXD1 ENET0_TXD0 NC ENET0_RXD0 F G H D DCDC_VDDD VDD1P5 LRADC5 JTAG_TRST LRADC4 JTAG_TMS RTC_XTALI SSP0_DETECT LRADC3 I2C0_SDA SPDIF SSP0_DATA2 SSP0_DATA6 SSP2_SS2 SSP2_SS1 NC NC D C DCDC_VDDIO VSS LRADC0 LRADC6 VDDA1 VDDXTAL RTC_XTALO TESTMODE LRADC1 LRADC2 I2C0_SCL SSP0_DATA1 SSP0_DATA5 SSP2_SS0 SSP2_MOSI NC NC C B DCDC_LN1 DCDC_VDDA DCDC_BATT HSADC0 VSSA1 XTALO VSSA2 USB0DP DEBUG USB1DM VSS SSP0_DATA0 SSP0_DATA4 SSP0_DATA7 SSP2_MISO NC NC B Package Information and Contact Assignments Table 68. 289-Pin i.MX286 MAPBGA Ball Map (continued) i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor Freescale Semiconductor 16 15 14 13 12 11 10 9 8 7 6 5 4 3 A DCDC_GND 17 DCDC_LP BATTERY RESETN VDD4P2 XTALI PSWITCH USB0DM VSS USB1DP VDDIO33 SSP0_SCK SSP0_DATA3 SSP0_CMD SSP2_SCK 2 1 4.7 SSP3_SCK VSS A EMI_A11 EMI_A04 T EMI_ODT0 17 VSSIO_EMI EMI_ODT1 U EMI_RASN EMI_BA0 16 EMI_CASN R VDDIO_EMIQ EMI_WEN 15 EMI_VREF0 VDDIO_EMI VSSIO_EMI EMI_A00 EMI_CKE EMI_BA1 EMI_A05 VSSIO_EMI EMI_A06 GPMI_D02 GPMI_D05 GPMI_RDN LCD_D23 LCD_D20 LCD_D17 LCD_D11 LCD_D10 VSSIO_EMI EMI_A10 EMI_A01 EMI_A03 EMI_A13 EMI_A08 EMI_A12 GPMI_D01 GPMI_D00 GPMI_D04 LCD_D22 LCD_D21 GPMI_D03 LCD_D19 LCD_D18 GPMI_D07 LCD_D16 LCD_D15 GPMI_D06 LCD_D13 LCD_D14 LCD_D12 VSS R EMI_A02 14 13 12 11 10 9 8 7 6 5 4 3 2 1 T U P EMI_D05 VSSIO_EMI EMI_D02 VSSIO_EMI EMI_D04 EMI_CE0N VDDIO_EMI EMI_A09 EMI_CE1N GPMI_WRN GPMI_CLE GPMI_ALE LCD_CS LCD_RD_E LCD_D09 LCD_D08 LCD_D07 P N VDDIO33_EMI EMI_D00 VDDIO_EMI EMI_D03 VDDIO_EMI EMI_BA2 EMI_A07 EMI_A14 GPMI_CE1N GPMI_RDY1 GPMI_CE0N GPMI_RDY0 NC VSS VDDIO33 LCD_D06 NC N M EMI_D07 VSSIO_EMI EMI_DQM0 VSS EMI_D01 VDDIO_EMI VDDIO_EMI VDDIO_EMI GPMI_CE3N GPMI_RDY2 GPMI_CE2N LCD_RESET NC LCD_RS LCD_D05 LCD_D04 NC M L EMI_CLK EMI_CLKN EMI_DDR_OPEN_FB EMI_D06 VDDIO_EMI VSSIO_EMI VSS VSS GPMI_RESETN GPMI_RDY3 PWM1 NC NC AUART1_RX LCD_D03 LCD_D02 NC L Package Information and Contact Assignments Table 68. 289-Pin i.MX286 MAPBGA Ball Map (continued) i.MX287 Ball Map Table 69 shows the i.MX287 MAPBGA Ball Map. Table 69. 289-Pin i.MX287 MAPBGA Ball Map i.MX28 Applications Processors for Consumer Products, Rev. 3 69 70 EMI_DQS1 J K EMI_D11 EMI_DDR_OPEN EMI_DQS0 VDDIO_EMIQ EMI_VREF1 EMI_DQS1N VSS VDDD EMI_DQS0N VSS VSS VSS VDDIO33 VSS VDDIO_EMIQ VDDIO33 AUART0_RTS AUART2_RTS SAIF0_MCLK PWM0 VSS SAIF0_BITCLK AUART0_CTS AUART2_CTS SAIF0_LRCLK AUART3_RTS VDDIO33 AUART2_RX AUART1_RTS AUART1_CTS PWM2 AUART2_TX AUART0_RX ENET0_COL AUART1_TX H EMI_D13 VSS EMI_D09 VSSIO_EMI EMI_D12 VSS VSS VSS VSS VDDIO33 AUART0_TX F G VSSIO_EMI EMI_D10 EMI_D15 EMI_D14 VDDIO_EMI VDDIO_EMI VDDD VDDD VSSIO_EMI VDDD VDDD EMI_D08 VDDD VDDD EMI_DQM1 VDDIO18 VDDIO18 VDDIO_EMI VDDIO18 ENET0_TX_EN VDDIO18 ENET0_MDIO ENET0_MDC ENET_CLK SSP1_DATA3 E E VDD5V VDDIO33 VSS JTAG_RTCK JTAG_TDO JTAG_TDI JTAG_TCK PWM4 PWM3 SAIF1_SDATA0 SAIF0_SDATA0 VDDIO33 VSS ENET0_RX_EN ENET0_RX_CLK ENET0_TX_CLK VSS ENET0_CRS LCD_D01 VDDIO33 ENET0_TXD1 ENET0_RXD3 ENET0_RXD1 ENET0_TXD3 F LCD_D00 G ENET0_TXD0 H ENET0_RXD2 ENET0_RXD0 ENET0_TXD2 J LCD_WR_RWN K D DCDC_VDDD VDD1P5 LRADC5 JTAG_TRST LRADC4 JTAG_TMS RTC_XTALI SSP0_DETECT LRADC3 I2C0_SDA SPDIF SSP0_DATA2 SSP0_DATA6 SSP2_SS2 SSP2_SS1 SSP3_SS0 SSP1_DATA0 D C DCDC_VDDIO VSS LRADC0 LRADC6 VDDA1 VDDXTAL RTC_XTALO TESTMODE LRADC1 LRADC2 I2C0_SCL SSP0_DATA1 SSP0_DATA5 SSP2_SS0 SSP2_MOSI SSP3_MOSI SSP1_CMD C B DCDC_LN1 DCDC_VDDA DCDC_BATT HSADC0 VSSA1 XTALO VSSA2 USB0DP DEBUG USB1DM VSS SSP0_DATA0 SSP0_DATA4 SSP0_DATA7 SSP2_MISO SSP3_MISO SSP1_SCK B Package Information and Contact Assignments Table 69. 289-Pin i.MX287 MAPBGA Ball Map (continued) i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor Freescale Semiconductor EMI_A05 VSSIO_EMI VDDIO_EMI EMI_VREF0 VDDIO_EMIQ EMI_RASN EMI_ODT0 LCD_D19 LCD_D22 GPMI_D07 GPMI_D04 GPMI_D01 EMI_A13 EMI_A11 EMI_A03 EMI_BA1 EMI_CKE VSSIO_EMI EMI_WEN EMI_BA0 LCD_D18 LCD_D21 GPMI_D06 GPMI_D03 GPMI_D00 EMI_A08 EMI_A04 EMI_A12 EMI_A01 EMI_A10 EMI_A02 EMI_A00 16 EMI_CASN 17 VSSIO_EMI EMI_ODT1 15 14 13 12 11 10 9 8 7 6 5 4 T VSSIO_EMI LCD_D16 LCD_D15 3 U EMI_A06 LCD_D13 LCD_D14 2 R GPMI_D02 GPMI_D05 GPMI_RDN LCD_D23 LCD_D20 LCD_D17 LCD_D11 LCD_D10 LCD_D12 VSS 1 R T U P EMI_D05 VSSIO_EMI EMI_D02 VSSIO_EMI EMI_D04 EMI_CE0N VDDIO_EMI EMI_A09 EMI_CE1N GPMI_WRN GPMI_CLE GPMI_ALE LCD_CS LCD_RD_E LCD_D09 LCD_D08 LCD_D07 P M LCD_RS LCD_D05 LCD_D04 N VDDIO33_EMI EMI_D00 VDDIO_EMI EMI_D03 VDDIO_EMI EMI_BA2 EMI_A07 EMI_A14 GPMI_CE1N GPMI_RDY1 GPMI_CE0N GPMI_RDY0 M EMI_D07 VSSIO_EMI EMI_DQM0 VSS EMI_D01 VDDIO_EMI VDDIO_EMI VDDIO_EMI GPMI_CE3N GPMI_RDY2 GPMI_CE2N LCD_RESET LCD_ENABLE AUART3_RX VSS VDDIO33 LCD_D06 LCD_DOTCLK LCD_HSYNC N L EMI_CLK EMI_CLKN EMI_DDR_OPEN_FB EMI_D06 VDDIO_EMI VSSIO_EMI VSS VSS GPMI_RESETN GPMI_RDY3 PWM1 AUART3_CTS AUART3_TX AUART1_RX LCD_D03 LCD_D02 LCD_VSYNC L Package Information and Contact Assignments Table 69. 289-Pin i.MX287 MAPBGA Ball Map (continued) i.MX28 Applications Processors for Consumer Products, Rev. 3 71 Revision History 5 Revision History Table 70 summarizes revisions to this document. Table 70. Document Revision History Rev. Number Date Rev. 3 07/2012 * Removed the Power Consumption table, and added Table 12, "Run IDD Test Case,," on page 14. * Updated Table 23, "ON Impedance of EMI Drivers for Different Drive Strengths," on page 20. Rev. 2 03/2012 * In Section 1.1, "Device Features:" --Updated synchronous serial ports (SSP) support for the i.MX28 --Updated Ethernet support for the i.MX28 --Updated Low-Resolution A/D Converter (LRADC) support for the i.MX28 * Updated Table 2, "i.MX28 Functional Differences," on page 4. * In Table 6, "DC Absolute Maximum Ratings," on page 12, removed the PSWITCH parameter as this paramater is explained in detail in Table 11. * In Table 8, "Recommended Power Supply Operating Conditions," on page 13: --Updated two parameters: "VDD5V Supply Voltage" and "Offstate Current" --Updated the third footnote * In Table 9, "Operating Temperature Conditions," on page 13, added a new footnote in the "Parameter" column. * In Table 13, "Power Supply Characteristics," on page 15, updated the "VDD4P2 Output Current Limit Accuracy" parameter. * In Section 3.1.2.1, "Recommended Operating Conditions for Specific Clock Targets:" --Removed the "System Clocks" table --Updated two TBD values in the first row of Table 14 --Removed the first row in Table 15 --Removed the first row in Table 16 * In Table 20, "Power Mode Settings," on page 17, changed the second column name from "Deep Sleep" to "Offstate." * Updated Table 22, "EMI Digital Pin DC Characteristics," on page 20. * In Table 30, "LRADC Electrical Specifications," on page 27, updated the "DC Electrical Specification" section. * In Table 31, "HSADC Electrical Specification," on page 28, updated the "DC Electrical Specification" section. * In Section 3.5.5, "Coresight ETM9 AC Interface Timing," updated the first paragraph. * In Section 3.5.5.1, "TRACECLK Timing," corrected the title of Table 43. * In Section 3.5.5.2, "Trace Data Signal Timing," corrected the titles of Figure 15 and Table 44. Rev. 1 04/2011 * * * * * * * * Substantive Change(s) * * * * * * Updated Section 1.1, "Device Features." Added Section 3.2, "Thermal Characteristics." In Table 1, "Ordering Information," on page 3, added two rows. Updated Table 2, "i.MX28 Functional Differences," on page 4. Updated Table 4, "i.MX28 Digital and Analog Modules," on page 7. In Table 8, "Recommended Power Supply Operating Conditions," on page 13, updated BATT row. Updated Table 9, "Operating Temperature Conditions," on page 13. Replaced the term "DC Characteristics" with "Power Consumption" in the title and introduction of the Power Consumption table. Also changed Dissipation to Consumption in first row. Updated Table 25, "Digital Pin DC Characteristics for GPIO in 3.3-V Mode," on page 21. Updated Table 26, "Digital Pin DC Characteristics for GPIO in 1.8 V Mode," on page 22. Updated and added a footnote to Table 33, "Ethernet PLL Specifications," on page 29. Updated DDR1 row of Table 34, "EMI Command/Address AC Timing," on page 30. Added Section 4.4, "i.MX280 Ball Map." In Section 4.5, "i.MX283 Ball Map," updated Figure 67. i.MX28 Applications Processors for Consumer Products, Rev. 3 72 Freescale Semiconductor Revision History Table 70. Document Revision History (continued) Rev. Number Rev. 0 Date Substantive Change(s) 09/2010 Initial release. i.MX28 Applications Processors for Consumer Products, Rev. 3 Freescale Semiconductor 73 How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 support.asia@freescale.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product or service names are the property of their respective owners. ARM is the registered trademark of ARM Limited. ARM9 is a trademark of ARM Limited. (c) 2012 Freescale Semiconductor, Inc. All rights reserved. Document Number: IMX28CEC Rev. 3 07/2012