NUMBER TYPE GS-12-622 Product Specification TITLE PAGE REVISION 1 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED 1.0 SCOPE 2.0 PRODUCT DESCRIPTION 2.1 2.2 2.3 3.0 Product Name and Series Number(s) Dimensions, Materials, Plating and Markings Additional General Specifications REFERENCE DOCUMENTS 3.1 3.2 FCI Documents Industrial Documents 4.0 QUALIFICATION 5.0 RATINGS 5.1 5.2 5.3 6.0 Voltage Current Temperature PERFORMANCE 6.1 6.2 6.3 6.4 6.5 6.6 6.7 7.0 Electrical Characteristics ESD Requirements EMI Protection QSFP+ Pin Assignment 2 Wire Interface EEPROM ( Lower and Upper Page ) Mechanical Characteristics Environmental Requirements QUALITY ASSURANCE PROVISIONS 7.1 7.2 7.3 7.4 7.5 7.6 Equipment Calibration Inspection Conditions Sample Quantity and Description Acceptance Qualification Testing Requalification Testing 8.0 SUPPORTING INFORMATION 9.0 REVISION RECORD Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE Product Specification GS-12-622 TITLE PAGE REVISION 2 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED 1.0 SCOPE This specification is applicable to the performance characteristics of QSFP+ cable to board connector system. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER(S) Product 10G QSFP Cable Assembly 14G QSFP+ Cable Assembly 28G QSFP+ Cable Assembly QSFP SMT Board Connector QSFP Cage QSFP Heat Sink QSFP Heat Sink Clip QSFP Cage with Sink and Clip Assembly Custom QSFP Cable Assembly Custom QSFP Cable Assembly 2.2 Series P/N 10093084 10119239 10121178 10099113/10132344 10099114/10128765/10130975 10099115 10099116 10116015/10128764 10110113 10111727 Test Sections Do Not Apply 3.2, 6.4, 6.5 3.2, 6.4, 6.5 DIMENSIONS, MATERIALS, PLATING AND MARKINGS Refer to the applicable customer drawing for the related dimensional, material, plating, and marking information. 2.3 ADDITIONAL GENERAL SPECIFICATIONS Plug PCB: * Material: FR4 * Overall thickness: 1.0mm 0.1(over pads) * Mating interface plating: Hard gold over nickel Bulk Cable: * As listed on the cable specification drawings. Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE Product Specification GS-12-622 TITLE PAGE REVISION 3 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED 3.0 REFERENCE DOCUMENTS 3.1 FCI DOCUMENTS GS-14-1272 GS-14-1400 GS-20-126 SI-2009-09-004 SI-VG-2012-04-001 SI-VG-2012-11-013 SI-VG-2012-11-021 GS-29-622 EL-2012-05-033 EL-2012-12-023 3.2 Cable Assembly Packaging Specification Board Connector, Cage, and Heat Sink Packaging Specification Board Connector, Cage, and Heat Sink Product Application Specification. 10G QSFP+ Signal Integrity Performance Report (This Applies Only To Standard Part Number) 14G QSFP+ Signal Integrity Performance Report (This only applies to the 14G QSFP+ Part Number) 4x28G QSFP+ Signal Integrity Performance Reports (This applies only to the 28G P/N) 10G Qualification Test Report Summary 14G Qualification Test Report 28G Qualification Test Report INDUSTRY DOCUMENTS FIT, FORM AND FUNCTION SFF-8436 QSFP+ Copper and Optical Modules SFF-8661 QSFP+ 28 Gb/s 4X Pluggable Module (Style A) SFF-8662 QSFP+ 28 Gb/s 4X Connector (Style A) or SFF-8672 QSFP+ 28 Gb/s 4X Connector (Style B) SFF-8663 QSFP+ 28 Gb/s 4X Cage (Style A) IEEE 802.3 Gigabit Ethernet Standard Infiniband IBTA FDR (This applies only to the 14G QSFP+ P/N) InfiniBand IBTA EDR (This applies only to the 4x28G QSFP+ P/N) ITU-T G.957 Synchronous Digital Hierarchy Standard Telcordia Technologies GR-253-CORE JEDEC JESD22-A-114B ESD Specification TEST SPECIFICATON(S) EIA 364 Series Procedure Electrical Connector Test Procedures Including Environmental Classifications with Test Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE Product Specification GS-12-622 TITLE PAGE REVISION 4 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED 4.0 QUALIFICATION Connector and cable assemblies furnished under this specification shall be capable of meeting the qualification test requirements specified herein and shall be uniform in quality, and void of all defects that would adversely affect life or serviceability. 5.0 RATINGS 5.1 VOLTAGE 30 Volts AC per Contact (RMS)/DC Max. 5.2 CURRENT 0.5 Amps Max (per contact) 1.0 Amp Max (per power pin) 5.3 TEMPERATURE Operating: -40C to +85C 6.0 PERFORMANCE 6.1 ELECTRICAL CHARACTERISTICS DESCRIPTION TEST CONDITION REQUIREMENT 6.1.1 LLCR Mate connectors: apply a maximum voltage of 320 mV and a current of 10 mA. (EIA 364-6) 20 milliohm maximum change from initial after environmental exposure 6.1.2 Insulation Resistance After 100 VDC for 1 minute, measure the insulation resistance between adjacent mated contacts. (EIA 364-21) 6.1.3 Dielectric Withstanding Voltage Apply a voltage of 300 VDC for 1 minute hold between adjacent mated terminals. (EIA 364-20, method B) No defect between adjacent contacts 6.1.4 Temperature Rise (via Current Cycling) Mate connectors: measure the temperature rise at the rated current after 96 hours (45 minutes ON and 15 minutes OFF per hour). Testing as required. Temperature rise: +30C MAX. ITEM 1000 m Minimum between adjacent contacts Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE GS-12-622 Product Specification TITLE PAGE REVISION 5 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED 6.1.5 Differential Impedance Rise time of 70ps (20% to 80%) (EIA 364-108) No significant electrical change 6.1.6 Continuity Verify the continuous electrical path of all expected connections No unexpected opens, shorts, or high resistance areas. 6.2 ESD Requirements The module shall meet ESD requirements given in EN61000-4-2, criterion B test specification such that when installed in a properly grounded cage and chassis the units are subjected to 15KV air discharges during operation and 8KV direct contact discharges to the case. The QSFP+ module and host SFI contacts (High Speed Contacts) shall withstand 1000V electrostatic discharge based on human body model per JEDEC JESD22-A114-B. The QSFP+ module and host SFI contacts with the exception of the SFI contacts (High Speed Contacts) shall withstand 2kV electrostatic discharge based on human body model per JEDEC JESD22-A114-B. The QSFP+ module shall meet ESD requirements given in EN61000-4-2, criterion B test specification such that units are subjected to 15kV air discharges during operation and 8kv direct contact discharges to the case. 6.3 EMI Protection The chassis ground of the QSFP+ module is isolated from the modules circuit ground to provide the equipment designer flexibility regarding connections between external electromagnetic interference shields and circuit ground of the module. Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE GS-12-622 Product Specification TITLE PAGE REVISION 6 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED 6.4 QSFP+ Cable Assembly Pin Assignment (Figure 3). See Specification SFF- 8436 section 4. Module mechanicals meet the requirements of specification SFF-8436. FIGURE 3 QSFP+ Module Contact Definition Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE GS-12-622 Product Specification TITLE PAGE REVISION 7 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED 6.5 2 Wire Interface EEPROM The QSFP+ serial ID provides access to sophisticated identification information that describes the Transceiver's capabilities, standard interfaces, manufacturer, and other information. The EEPROM on the QSFP+ passive cable assembly is designed for 255 addresses. 10G QSFP+ & 14G FDR & 28G EDR EEPROM information and source Refer to below document TYPE FCI STANDARD QSFP+ FCI STANDARD FDR FCI STANDARD EDR FCI PN 10093084 10119329 10121178 Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE GS-12-622 Product Specification TITLE PAGE REVISION 8 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE GS-12-622 Product Specification TITLE PAGE REVISION 9 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE GS-12-622 Product Specification TITLE PAGE REVISION 10 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE GS-12-622 Product Specification TITLE PAGE REVISION 11 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE GS-12-622 Product Specification TITLE PAGE REVISION 12 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED MECHANICAL CHARACTERISTICS ITEM DESCRIPTION TEST CONDITION REQUIREMENT Cable Assembly: 50 Cycles Board Connector: 100 cycles Test Condition: 10 cycles per minute max. Latches to be disabled. (EIA 364-09, 364-23) 1. 6.6.1 Durability 6.6.2 Pre-conditioning Mate and un-mate samples 25 times. Test condition: 10 cycles per minute max. (EIA 364-09, 364-23) Mechanical Shock Mated samples subject to 30G, half-sine shock pulses of 11 milliseconds duration. 3 shocks in each direction applied in 3 mutually perpendicular planes (18 total). EIA 364-27, Method H 6.6.4 Random Vibration Mate samples subjected to 3.10G rms between 20 and 500 Hz for 15 minutes in each of 3 mutually perpendicular planes EIA 36428, Test Condition: VII 6.6.5 (Insertion & Extraction) Mating & Un-mating Forces 6.6.3 6.6.6 6.6.7 Cable Strain Relief Wire Flex Mate and un-mate samples 5 times. Measure the forces with the kick-out springs and latches disengaged. Place axial load on cable. Test Condition: 25mm/min head speed Cable flex 180 - 15 Cycles Test Condition : See Table 1 and Figure 2 (EIA 364-41) 6.6.8 Cable Minimum Bend Radius The cable is bent one time over the correct mandrel of size specified in Table 1 in each of 4 perpendicular directions. (Figure 1) 6.6.9 Latch Strength Mate connectors and place an axial load on the cable connector. 6.6.10 Cage Press Fit Insertion & Withdrawal Force Place axial load on the cage to measure the insertion and withdrawal force of the press-fit sections into and out of the PCB. 2. Max. 20m change from initial readings No visual damage No Physical Damage No Physical Damage 1. 2. 3. 1. 2. Max. 20m change from initial readings No visual damage No discontinuances greater than 1s 40N max mating force 30N max un-mating force 1. 2. 3. 4. 90N Minimum No physical damage. Verify continuity No significant electrical change (Diff Impedance) 1. 2. No physical damage. No loss of continuity during test. No significant electrical change (Diff Impedance) 3. 1. 2. 3. No physical damage. Verify continuity No significant electrical change (Diff Impedance) 1. 2. 90N Minimum No physical damage to the module or cage. 1. 550N Max. Insertion per press-fit section. 114N Min. Extraction per press-fit section. 2. Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE GS-12-622 Product Specification TITLE PAGE REVISION 13 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED Raw Cable AWG 8 Pair Minimum Bending Minimum Bending Standard Radius Repeated Radius Single 2.007" ( 51mm ) 1.004" ( 25.5mm ) 32AWG 2.598" ( 66mm ) 1.299"( 33mm ) 30AWG 2.952" ( 75mm ) 1.476" ( 37.5mm ) 28AWG 3.385" ( 86mm ) 1.693" ( 43mm ) 26AWG 3.818" ( 97mm ) 1.909" ( 48.5mm ) 24AWG Raw Cable AWG 8 Pair Minimum Bending Minimum Bending 4x28G Radius Repeated Radius Single 2.520" ( 64mm ) 1.260" ( 32mm ) 30AWG 3.189" ( 81mm ) 1.614" ( 41mm ) 26AWG * Minimum Bend Radius for all non standard cables will use the following formula: Repeated Bending = 10 X Cable Diameter and Single Bending = 5 X Cable Diameter Table 1 - Cable Minimum Bend Radius (See Figure 1 & 2) 6.6 ENVIRONMENTAL REQUIREMENTS ITEM DESCRIPTION 6.7.1 Thermal Shock Test Condition: 10 cycles -55C to +85C. (EIA 364-32C, condition I) Max. 20 milliohm change from initial readings 6.7.2 Temperature Life Cable should be mated and subject 70C for 500 hours EIA 364-17, Method A, Condition 2, Time Condition C Max. 20 milliohm change from initial readings 6.7.3 Humidity Temperature Cycling Cables unmated specimens to 10 cycles between 25C and 65C at 80% to 100% relative humidity EIA 364-31, Method III excluding steps 7a & 7b Max. 20 milliohm change from initial readings Mixed Flowing Gas Subject the board mounted receptacle to environmental Class IIA for 7 days unmated followed by 7 days mated (14 days total ) EIA 364-65, Class IIA Max. 20 milliohm change from initial readings Thermal Disturbance Cables are cycled between 153 and 853C as measured on the part. Ramps at min 2C/minute and dwells ensuring contacts reach extremes for 5 minutes minimum. Humidity not controlled. 10 cycles Max. 20 milliohm change from initial readings 6.7.4 6.7.5 7.0 TEST CONDITION REQUIREMENT QUALITY ASSURANCE PROVISIONS Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE Product Specification GS-12-622 TITLE PAGE REVISION 14 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED 7.1 Equipment Calibration All test equipment and inspection facilities used in the performance of any test shall be maintained in a calibration system in accordance with MIL-C-45662. 7.2 Inspection Conditions Unless otherwise specified herein, all inspections shall be performed under the following ambient conditions: a. Temperature: 25 +/- 5 degrees Celsius b. Barometric Pressure: Local ambient 7.3 Sample Quantity And Description Test Group Number of Cables 1 3 2 3 3 1 4 6 5 3 6 3 3 7 3 3 per wire gage tested Cable Description Number of Board Connectors Each AWG, double ended, 1 1 meter min Any AWG, single ended, 0.5 3 meter Any AWG, single ended, 0.5 6 Cages and 3 PCB meter Any AWG, single ended, 0.5 3 Board Connectors and 3 Loose Piece connectors meter Any AWG, single ended, 0.5 3 meter Any AWG, single ended, 0.5 3 meter Smallest AWG, single 3 ended, 0.5 meter Largest AWG, single 3 ended, 0.5 meter Non-terminated cables for board side connector 3 Paddle Boards and 1 Cage durabilty For qualification test samples, DC blocking capacitors on the receive channels are to be replaced by 0 ohm resistors so that LLCR measurements can be taken on the receive channels. Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE GS-12-622 Product Specification TITLE PAGE REVISION 15 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED 7.4 Acceptance 7.4.1 Electrical and mechanical requirements placed on test samples as indicated in section 6.0 shall be established from test data using appropriate statistical techniques. All samples tested in accordance with this product specification shall meet the stated requirements. 7.4.2 Failures attributed to equipment, test set-up, or operator error shall not disqualify the product. If product failure occurs, corrective action shall be taken and samples resubmitted for qualification. 7.5 Qualification Testing Qualification testing shall be performed on sample units produced with equipment and procedures normally used in production. The test sequence shall be as shown in Table 2. 7.6 Requalification Testing If any of the following conditions occur, the responsible product engineer shall initiate requalification testing consisting of all applicable parts of the qualification test matrix, Table 2. a. A significant design change is made to the existing product, which impacts the product form, fit or function. b. A significant change is made to the manufacturing process, which impacts the product form, fit or function. c. A significant event occurs during production or end use requiring corrective action to be taken relative to the product design or manufacturing process. Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE Product Specification GS-12-622 TITLE PAGE REVISION 16 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED TABLE 2 - QUALIFICATION TESTING MATRIX TEST GROUP TEST PARA 1 2 3 4 5 6 7 TEST SEQUENCE Examination of Product LLCR 1,12 1,3 1,4 6.1.1 1,11 1,5 1,14 1,11 2,6,8 2,4 2,5,7,9,11,1 3 2,5,7,9 Insulation Resistance (IR) 6.1.2 3,9 Dielectric Withstanding Voltage (DWV) 6.1.3 4,10 6.1.5 3,6,8, 11 Continuity 6.1.6 2,5,10 Durability 6.6.1 Pre-conditioning 6.6.2 Mechanical Shock 6.6.3 6 Random Vibration 6.6.4 8 Mating/Un-mating Force 6.6.5 Cable Strain Relief 6.6.6 9 Wire Flex 6.6.7 7 Minimum Bend Radii 6.6.8 4 Latch Strength 6.6.9 Differential Impedance Cage Press-fit Insertion Force 4 4 3,12 3,10 2 2 6.6.10 Cage Press-fit Withdrawal 3 Thermal Shock 6.7.1 5 Temperature Life 6.7.2 Humidity Temperate Cycling 6.7.3 Mixed Flowing Gas 6.7.4 6,8 Thermal Disturbance 6.7.5 10 3 7 Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE GS-12-622 Product Specification TITLE PAGE REVISION 17 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED 8.0 SUPPORTING INFORMATION Figure 1 - Single Minimum Bending Radius ( See Mechanical Characteristics 6.1.9 and Table 1 ) Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE GS-12-622 Product Specification TITLE PAGE REVISION 18 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED Figure 2 - Repeated Wire Flex Test ( See Mechanical Characteristics 6.1.8 and Table 1 ) Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 NUMBER TYPE Product Specification GS-12-622 TITLE PAGE REVISION 19 of 19 QSFP+ Cable to Board Connector System N AUTHORIZED BY DATE Michael Zhou Aug-21-2015 CLASSIFICATION UNRESTRICTED 9.0 REVISION RECORD REV. PAGE DESCRIPTION ECR DATE A All Release from Preliminary V10-0131 2004/5/10 B All Rev. A to B, Changed bend radius in Table 1 Repeatable .97 to 2.007, 1.61 to 2.598, 1.69 to 2.952, 1.93 to 3.385, 2.20 to 3.818 and Single, .69 to 1.004, .81 to 1.299, .85 to 1.476, .96 to 1.693, 1.10 to 1.909 V10-0290 2007/7/10 C 2 Adding new P/N 10116015 ECN-ELX-N003201-1 3-14-11 D All Removed E-Prom Address from specification. ECN-ELX-V010413-1 2-27-12 3 Added applicable information for 14G QSFP+ Cable Assembly ECR-ELX-V011521 2005/2/12 E Add EEPROM Section back into Spec F 8 Updated contents of address 131 to comply with the latest rev of SFF-8436 ECR-ELX-V13361 2011/2/12 G 29 Update Test Plan to remove LLCR Step 11 from Test Group 4 ECN-ELX-V14334-1 3-25-13 ECN-ELX-V15186-1 2007/9/13 Changed requirement in section 6.1.5, Corrected dec equivalent on address 131, Corrected Vendor OUI, Updated table 2 to add continuity and update sequence of test group 1 ECN-ELX-N15503-1 8-27-13 Added applicable information for 28G QSFP+ Cable Assembly H All, 5, 7, 26, 27 Updated Impedance requirement, 6.1.5, 6.6.6, 6.6.7, 6.6.8; Added 6.1.6, Updated memory map, Updated the table in section 7.3, Change repeated bend radius Corrected revision change description for Rev H. J 5, 8, 15, 29, 32 K 15 Delete previous EEPROM content and add FCI standard QDR & FDR & EDR EEPROM ECN-ELX-N16985-1 2005/6/14 L 11 Update the QSFP Plus Attenuation table ECN-ELX-N17658-1 7-18-14 M 2 Adding new P/N 101323441012876410128765 10130975 N 2,8,10 Revise the map content per the latest industrial spec ECN-ELX-DG20036-1 ECN-ELX-N21737-1 1-21-15 8-21-15 Copyright FCI Form E-3334 Rev F GS-01-001 PDS: Rev :N STATUS:Released Printed: Aug 21, 2015 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: FCI: 10099113-101LF 10099114-001LF 10099115-002LF 10099116-001LF 10116015-001LF 10119239-2020LF 10119239-4040LF 10119239-2010LF 10119239-4030LF 10119239-6050LF 10099113-102LF 10119239-4010LF 10121178-4035LF 10121178-4020LF 10119239-4025LF 10121178-2015LF 10119239-4015LF 10121178-4005LF 10121178-4015LF 10121178-4010LF 10121178-4050LF 10119239-4005LF 10117436-001LF 10121178-2030LF 10121178-2025LF 10121178-4030LF 10121178-2010LF 10119239-4020LF 10119239-6030LF 10121178-4045LF 10119239-6040LF 10121178-4040LF 10119239-2025LF 10119239-2015LF 10121178-4025LF 10121178-2020LF 10119239-4035LF 10119239-2005LF 10121178-2005LF