LPV521 LPV521 Nanopower, 1.8V, RRIO, CMOS Input, Operational Amplifier Literature Number: SNOSB14B LPV521 Nanopower, 1.8V, RRIO, CMOS Input, Operational Amplifier General Description Features The LPV521 is a single nanopower 552 nW amplifier designed for ultra long life battery applications. The operating voltage range of 1.6V to 5.5V coupled with typically 351 nA of supply current make it well suited for RFID readers and remote sensor nanopower applications. The device has input common mode voltage 0.1V over the rails, guaranteed TCVOS and voltage swing to the rail output performance. The LPV521 has a carefully designed CMOS input stage that outperforms competitors with typically 40 fA IBIAS currents. This low input current significantly reduces IBIAS and IOS errors introduced in megohm resistance, high impedance photodiode, and charge sense situations. The LPV521 is a member of the PowerWise(R) family and has an exceptional power-to-performance ratio. The wide input common mode voltage range, guaranteed 1 mV VOS and 3.5 V/C TCVOS enables accurate and stable measurement for both high side and low side current sensing. EMI protection was designed into the device to reduce sensitivity to unwanted RF signals from cell phones or other RFID readers. The LPV521 is offered in the 5-pin SC-70 package. (For VS = 5V, Typical unless otherwise noted) 400 nA (max) Supply current at VCM = 0.3V 1.6V to 5.5V Operating voltage range 3.5 V/C (max) Low TCVOS 1 mV (max) VOS 40 fA Input bias current 109 dB PSRR 102 dB CMRR 132 dB Open loop gain 6.2 kHz Gain bandwidth product 2.4 V/ms Slew rate 255 nV/Hz Input voltage noise at f = 100 Hz -40C to 125C Temperature range Applications Wireless remote sensors Powerline monitoring Power meters Battery powered industrial sensors Micropower oxygen sensor and gas sensor Active RFID readers Zigbee based sensors for HVAC control Sensor network powered by energy scavenging Typical Application 30054578 30054577 (c) 2009 National Semiconductor Corporation 300545 www.national.com LPV521 Nanopower, 1.8V, RRIO, CMOS Input, Operational Amplifier August 24, 2009 LPV521 Storage Temperature Range Junction Temperature (Note 3) Mounting Temperature Infrared or Convection (30 sec.) Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) Human Body Model Machine Model Charge-Device Model Any pin relative to VIN+, IN-, OUT Pins V+, V-, OUT Pins Differential Input Voltage (VIN+ - VIN-) 260C Wave Soldering Lead Temp. (4 sec.) 2000V 200V 1000V 6V, -0.3V V+ + 0.3V, V- - 0.3V Operating Ratings 260C (Note 1) Temperature Range (Note 3) Supply Voltage (VS = V+ - V-) -40C to 125C 1.6V to 5.5V Package Thermal Resistance (JA) (Note 3) 5-Pin SC-70 40mA 300 mV 1.8V DC Electrical Characteristics -65C to 150C 150C 456 C/W (Note 4) Unless otherwise specified, all limits guaranteed for TA = 25C, V+ = 1.8V, V- = 0V, VCM = VO = V+/2, and RL > 1 M. Boldface limits apply at the temperature extremes. Symbol VOS Parameter Input Offset Voltage Conditions Min (Note 6) Typ (Note 5) Max (Note 6) VCM = 0.3V 0.1 1.0 1.23 VCM = 1.5V 0.1 1.0 1.23 Units mV TCVOS Input Offset Voltage Drift (Note 9) 0.4 3 V/C IBIAS Input Bias Current 0.01 1 50 pA IOS Input Offset Current CMRR Common Mode Rejection Ratio 10 0V VCM 1.8V 66 60 92 0V VCM 0.7V 75 74 101 1.2V VCM 1.8V 75 53 120 109 PSRR Power Supply Rejection Ratio 1.6V V+ 5.5V VCM = 0.3V 85 76 CMVR Common Mode Voltage Range CMRR 67 dB 0 0 CMRR 60 dB AVOL Large Signal Voltage Gain VO = 0.5V to 1.3V RL = 100 k to VO IO IS V+/2 74 73 fA dB dB 1.8 1.8 125 dB Output Swing High RL = 100 k to V+/2 VIN(diff) = 100 mV 2 50 50 Output Swing Low RL = 100 k to V+/2 VIN(diff) = -100 mV 2 50 50 Output Current (Note 7) Sourcing, VO to V- VIN(diff) = 100 mV 1 0.5 3 Sinking, VO to V+ VIN(diff) = -100 mV 1 0.5 3 Supply Current www.national.com mV from either rail mA VCM = 0.3V 345 400 580 VCM = 1.5V 472 600 850 2 V nA (Note 4) Unless otherwise specified, all limits guaranteed for TA = 25C, V+ = 1.8V, V- = 0V, VCM = VO = V+/2, and RL > 1 M. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min (Note 6) Typ (Note 5) GBW Gain-Bandwidth Product CL = 20 pF, RL = 100 k 6.1 SR Slew Rate AV = +1, VIN = 0V to 1.8V Falling Edge 2.9 Rising Edge 2.3 m Phase Margin CL = 20 pF, RL = 100 k Gm Gain Margin CL = 20 pF, RL = 100 k en Input-Referred Voltage Noise Density f = 100 Hz 265 Input-Referred Voltage Noise 0.1 Hz to 10 Hz 24 Input-Referred Current Noise f = 100 Hz 100 in 3.3V DC Electrical Characteristics Max (Note 6) Units kHz V/ms 72 deg 19 dB nV/ VPP fA/ (Note 4) Unless otherwise specified, all limits guaranteed for TA = 25C, V+ = 3.3V, V- = 0V, VCM = VO = V+/2, and RL > 1 M. Boldface limits apply at the temperature extremes. Symbol VOS Parameter Input Offset Voltage Conditions Min (Note 6) Typ (Note 5) Max (Note 6) VCM = 0.3V 0.1 1.0 1.23 VCM = 3V 0.1 1.0 1.23 Units mV TCVOS Input Offset Voltage Drift (Note 9) 0.4 3 V/C IBIAS Input Bias Current 0.01 1 50 pA IOS Input Offset Current CMRR Common Mode Rejection Ratio 20 0V VCM 3.3V 72 70 97 0V VCM 2.2V 78 75 106 2.7V VCM 3.3V 77 76 121 85 76 109 PSRR Power Supply Rejection Ratio 1.6V V+ 5.5V VCM = 0.3V CMVR Common Mode Voltage Range CMRR 72 dB -0.1 0 CMRR 70 dB AVOL Large Signal Voltage Gain VO = 0.5V to 2.8V RL = 100 k to V+/2 VO IO Output Swing High 82 76 dB dB 3.4 3.3 120 RL = 100 k to V+/2 VIN(diff) = 100 mV 3 Output Swing Low RL = 100 k to V+/2 VIN(diff) = -100 mV 2 Output Current (Note 7) Sourcing, VO to V- VIN(diff) = 100 mV 5 4 11 Sinking, VO to V+ VIN(diff) = -100 mV 5 4 12 3 fA V dB 50 50 50 50 mV from either rail mA www.national.com LPV521 1.8V AC Electrical Characteristics LPV521 Symbol IS Parameter Supply Current Conditions Typ (Note 5) Max (Note 6) VCM = 0.3V 346 400 600 VCM = 3V 471 600 860 3.3V AC Electrical Characteristics Min (Note 6) Units nA (Note 4) Unless otherwise is specified, all limits guaranteed for TA = 25C, V+ = 3.3V, V- = 0V, VCM = VO = V+/2, and RL > 1 M. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min (Note 6) Typ (Note 5) GBW Gain-Bandwidth Product CL = 20 pF, RL = 100 k 6.2 SR Slew Rate AV = +1, VIN = 0V to 3.3V Falling Edge 2.9 Rising Edge 2.5 m Phase Margin Gm Gain Margin en Input-Referred Voltage Noise Density f = 100 Hz 259 Input-Referred Voltage Noise 0.1 Hz to 10 Hz 22 Input-Referred Current Noise f = 100 Hz 100 in Max (Note 6) Units kHz V/ms CL = 20 pF, RL = 10 k 73 deg CL = 20 pF, RL = 10 k 19 dB 5V DC Electrical Characteristics nV/ VPP fA/ (Note 4) Unless otherwise specified, all limits guaranteed for TA = 25C, V+ = 5V, V- = 0V, VCM = VO = V+/2, and RL > 1M. Boldface limits apply at the temperature extremes. Symbol VOS Parameter Input Offset Voltage Conditions Min (Note 6) Typ (Note 5) Max (Note 6) VCM = 0.3V 0.1 1.0 1.23 VCM = 4.7V 0.1 1.0 1.23 Units mV TCVOS Input Offset Voltage Drift (Note 9) 0.4 3.5 V/C IBIAS Input Bias Current 0.04 1 50 pA IOS Input Offset Current CMRR Common Mode Rejection Ratio 60 0V VCM 5.0V 75 74 102 0V VCM 3.9V 84 80 108 4.4V VCM 5.0V 77 76 115 85 76 109 PSRR Power Supply Rejection Ratio 1.6V V+ 5.5V VCM = 0.3V CMVR Common Mode Voltage Range CMRR 75 dB -0.1 0 CMRR 74 dB AVOL Large Signal Voltage Gain VO = 0.5V to 4.5V RL = 100 k to V+/2 VO 84 76 fA dB dB 5.1 5 132 dB Output Swing High RL = 100 k to V+/2 VIN(diff) = 100 mV 3 50 50 Output Swing Low V+/2 3 50 50 www.national.com RL = 100 k to VIN (diff) = -100 mV 4 V mV from either rail IO Parameter Output Current (Note 7) IS Supply Current Conditions Min (Note 6) Typ (Note 5) Sourcing, VO to V- VIN(diff) = 100 mV 15 8 23 Sinking, VO to V+ VIN(diff) = -100 mV 15 8 22 Max (Note 6) mA VCM = 0.3V 351 400 620 VCM = 4.7V 475 600 870 5V AC Electrical Characteristics Units nA (Note 4) Unless otherwise specified, all limits guaranteed for TA = 25C, V+ = 5V, V- = 0V, VCM = VO = V+/2, and RL > 1M. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions GBW Gain-Bandwidth Product CL = 20 pF, RL = 100 k SR Slew Rate AV = +1, VIN = 0V to 5V Min (Note 6) Typ (Note 5) Max (Note 6) Units 6.2 Falling Edge 1.1 1.2 2.7 Rising Edge 1.1 1.2 2.4 m Phase Margin Gm Gain Margin en Input-Referred Voltage Noise Density f = 100 Hz 255 Input-Referred Voltage Noise 0.1 Hz to 10 Hz 22 in Input-Referred Current Noise f = 100 Hz 100 EMIRR EMI Rejection Ratio, IN+ and IN- (Note 8) VRF_PEAK = 100 mVP (-20 dBP), f = 400 MHz 121 VRF_PEAK = 100 mVP (-20 dBP), f = 900 MHz 121 VRF_PEAK = 100 mVP (-20 dBP), f = 1800 MHz 124 VRF_PEAK = 100 mVP (-20 dBP), f = 2400 MHz 142 kHz V/ms CL = 20 pF, RL = 100 k 73 deg CL = 20 pF, RL = 100 k 20 dB nV/ VPP fA/ dB Note 1: Absolute Maximum Ratings indicate limits beyond which damage may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC) Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC). Note 3: The maximum power dissipation is a function of TJ(MAX), JA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/ JA. All numbers apply for packages soldered directly onto a PC Board. Note 4: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that TJ = TA. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self-heating where TJ > TA. Absolute Maximum Ratings indicate junction temperature limits beyond which the device may be permanently degraded, either mechanically or electrically. Note 5: Typical values represent the most likely parametric norm at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material. Note 6: All limits are guaranteed by testing, statistical analysis or design. Note 7: The short circuit test is a momentary open loop test. Note 8: The EMI Rejection Ratio is defined as EMIRR = 20log (VRF_PEAK/VOS). Note 9: The offset voltage average drift is determined by dividing the change in VOS at the temperature extremes by the total temperature change. 5 www.national.com LPV521 Symbol LPV521 Connection Diagram 5-Pin SC-70 30054581 Top View Ordering Information Package Part Number Package Marking LPV521MG 5-Pin SC-70 LPV521MGE AHA 250 Units Tape and Reel LPV521MGX www.national.com Transport Media NSC Drawing 1k Units Tape and Reel 3k Units Tape and Reel 6 MAA05A LPV521 Typical Performance Characteristics At TJ = 25C, unless otherwise specified. Supply Current vs. Supply Voltage Supply Current vs. Supply Voltage 30054504 30054535 Offset Voltage Distribution TCVOS Distribution 30054573 30054574 Offset Voltage Distribution TCVOS Distribution 30054575 30054567 7 www.national.com LPV521 Offset Voltage Distribution TCVOS Distribution 30054568 30054569 Input Offset Voltage vs. Input Common Mode Input Offset Voltage vs. Input Common Mode 30054505 30054506 Input Offset Voltage vs. Input Common Mode Input Offset Voltage vs. Supply Voltage 30054537 30054507 www.national.com 8 Input Offset Voltage vs. Output Voltage 30054538 30054539 Input Offset Voltage vs. Output Voltage Input Offset Voltage vs. Output Voltage 30054541 30054540 Input Offset Voltage vs. Sourcing Current Input Offset Voltage vs. Sourcing Current 30054542 30054543 9 www.national.com LPV521 Input Offset Voltage vs. Supply Voltage LPV521 Input Offset Voltage vs. Sourcing Current Input Offset Voltage vs. Sinking Current 30054545 30054544 Input Offset Voltage vs. Sinking Current Input Offset Voltage vs. Sinking Current 30054546 30054547 Sourcing Current vs. Output Voltage Sinking Current vs. Output Voltage 30054509 30054508 www.national.com 10 LPV521 Sourcing Current vs. Output Voltage Sinking Current vs. Output Voltage 30054511 30054510 Sourcing Current vs. Output Voltage Sinking Current vs. Output Voltage 30054552 30054553 Sourcing Current vs. Supply Voltage Sinking Current vs. Supply Voltage 30054548 30054549 11 www.national.com LPV521 Output Swing High vs. Supply Voltage Output Swing Low vs. Supply Voltage 30054551 30054550 Input Bias Current vs. Common Mode Voltage Input Bias Current vs. Common Mode Voltage 30054515 30054514 Input Bias Current vs. Common Mode Voltage Input Bias Current vs. Common Mode Voltage 30054516 www.national.com 30054564 12 Input Bias Current vs. Common Mode Voltage 30054565 30054566 PSRR vs. Frequency CMRR vs. Frequency 30054527 30054560 Frequency Response vs. Temperature Frequency Response vs. Temperature 30054523 30054524 13 www.national.com LPV521 Input Bias Current vs. Common Mode Voltage LPV521 Frequency Response vs. Temperature Frequency Response vs. RL 30054522 30054520 Frequency Response vs. RL Frequency Response vs. RL 30054521 30054519 Frequency Response vs. CL Frequency Response vs. CL 30054517 www.national.com 30054518 14 LPV521 Frequency Response vs. CL Slew Rate vs. Supply Voltage 30054513 30054536 Voltage Noise vs. Frequency 0.1 to 10 Hz Time Domain Voltage Noise 30054526 30054561 0.1 to 10 Hz Time Domain Voltage Noise 0.1 to 10 Hz Time Domain Voltage Noise 30054563 30054562 15 www.national.com LPV521 Small Signal Pulse Response Small Signal Pulse Response 30054531 30054530 Large Signal Pulse Response Large Signal Pulse Response 30054532 30054533 Overload Recovery Waveform EMIRR vs. Frequency 30054534 30054572 www.national.com 16 LPV521 Application Information The LPV521 is fabricated with National Semiconductor's state-of-the-art VIP50 process. This proprietary process dramatically improves the performance of National Semiconductor's low-power and low-voltage operational amplifiers. The following sections showcase the advantages of the VIP50 process and highlight circuits which enable ultralow power consumption. 60 HZ TWIN T NOTCH FILTER Small signals from transducers in remote and distributed sensing applications commonly suffer strong 60 Hz interference from AC power lines. The circuit of Figure 1 notches out the 60 Hz and provides a gain AV = 2 for the sensor signal represented by a 1 kHz sine wave. Similar stages may be cascaded to remove 2nd and 3rd harmonics of 60 Hz. Thanks to the nA power consumption of the LPV521, even 5 such circuits can run for 9.5 years from a small CR2032 lithium cell. These batteries have a nominal voltage of 3V and an end of life voltage of 2V. With an operating voltage from 1.6V to 5.5V the LPV521 can function over this voltage range. The notch frequency is set by F0 = 1/2RC. To achieve a 60 Hz notch use R = 10 M and C = 270 pF. If eliminating 50 Hz noise, which is common in European systems, use R = 11.8 M and C = 270 pF. The Twin T Notch Filter works by having two separate paths from VIN to the amplifier's input. A low frequency path through the resistors R - R and another separate high frequency path through the capacitors C - C. However, at frequencies around the notch frequency, the two paths have opposing phase angles and the two signals will tend to cancel at the amplifier's input. To ensure that the target center frequency is achieved and to maximize the notch depth (Q factor) the filter needs to be as balanced as possible. To obtain circuit balance, while overcoming limitations of available standard resistor and capacitor values, use passives in parallel to achieve the 2C and R/2 circuit requirements for the filter components that connect to ground. To make sure passive component values stay as expected clean board with alcohol, rinse with deionized water, and air dry. Make sure board remains in a relatively low humidity environment to minimize moisture which may increase the conductivity of board components. Also large resistors come with considerable parasitic stray capacitance which effects can be reduced by cutting out the ground plane below components of concern. Large resistors are used in the feedback network to minimize battery drain. When designing with large resistors, resistor thermal noise, op amp current noise, as well as op amp voltage noise, must be considered in the noise analysis of the circuit. The noise analysis for the circuit in Figure 1 can be done over a bandwidth of 5 kHz, which takes the conservative approach of overestimating the bandwidth (LPV521 typical GBW/AV is lower). The total noise at the output is approximately 800 Vpp, which is excellent considering the total consumption of the circuit is only 540 nA. The dominant noise terms are op amp voltage noise (550 Vpp), current noise through the feedback network (430 Vpp), and current noise through the notch filter network (280 Vpp). Thus the total circuit's noise is below 1/2 LSB of a 10 bit system with a 2 V reference, which is 1 mV. 30054576 FIGURE 1. 60 Hz Notch Filter 30054577 FIGURE 2. 60 Hz Notch Filter Waveform BATTERY CURRENT SENSING The rail-to-rail common mode input range and the very low quiescent current make the LPV521 ideal to use in high side and low side battery current sensing applications. The high side current sensing circuit in Figure 3 is commonly used in a battery charger to monitor the charging current in order to prevent over charging. A sense resistor RSENSE is connected in series with the battery. The theoretical output voltage of the circuit is VOUT = [ (RSENSE x R3) / R1 ] x ICHARGE. In reality, however, due to the finite Current Gain, , of the transistor the current that travels through R3 will not be ICHARGE, but instead, will be x ICHARGE or /( +1) x ICHARGE. A Darlington pair can be used to increase the and performance of the measuring circuit. Using the components shown in Figure 3 will result in VOUT 4000 x ICHARGE. This is ideal to amplify a 1 mA ICHARGE to near full scale of an ADC with VREF at 4.1V. A resistor, R2 is used at the non-inverting input of the amplifier, with the same value as R1 to minimize offset voltage. Selecting values per Figure 3 will limit the current traveling through the R1 - Q1 - R3 leg of the circuit to under 1 A which is on the same order as the LPV521 supply current. Increasing resistors R1 , R2 , and R3 will decrease the measuring circuit supply current and extend battery life. Decreasing RSENSE will 17 www.national.com LPV521 minimize error due to resistor tolerance, however, this will also decrease VSENSE = ICHARGE x RSENSE, and in turn the amplifier offset voltage will have a more significant contribution to the total error of the circuit. With the components shown in Figure 3 the measurement circuit supply current can be kept below 1.5 A and measure 100 A to 1 mA.. TCVOS , low input bias current, high CMRR, and high PSRR are other factors which make the LPV521 a great choice for this application. 30054559 FIGURE 4. Precision Oxygen Sensor INPUT STAGE The LPV521 has a rail-to-rail input which provides more flexibility for the system designer. Rail-to-rail input is achieved by using in parallel, one PMOS differential pair and one NMOS differential pair. When the common mode input voltage (VCM) is near V+, the NMOS pair is on and the PMOS pair is off. When VCM is near V-, the NMOS pair is off and the PMOS pair is on. When VCM is between V+ and V-, internal logic decides how much current each differential pair will get. This special logic ensures stable and low distortion amplifier operation within the entire common mode voltage range. Because both input stages have their own offset voltage (VOS) characteristic, the offset voltage of the LPV521 becomes a function of VCM. VOS has a crossover point at 1.0V below V+. Refer to the 'VOS vs. VCM' curve in the Typical Performance Characteristics section. Caution should be taken in situations where the input signal amplitude is comparable to the VOS value and/or the design requires high accuracy. In these situations, it is necessary for the input signal to avoid the crossover point. In addition, parameters such as PSRR and CMRR which involve the input offset voltage will also be affected by changes in VCM across the differential pair transition region. 30054502 FIGURE 3. High Side Current Sensing PORTABLE GAS DETECTION SENSOR Gas sensors are used in many different industrial and medical applications. They generate a current which is proportional to the percentage of a particular gas sensed in an air sample. This current goes through a load resistor and the resulting voltage drop is measured. Depending on the sensed gas and sensitivity of the sensor, the output current can be in the order of tens of microamperes to a few milliamperes. Gas sensor datasheets often specify a recommended load resistor value or they suggest a range of load resistors to choose from. Oxygen sensors are used when air quality or oxygen delivered to a patient needs to be monitored. Fresh air contains 20.9% oxygen. Air samples containing less than 18% oxygen are considered dangerous. Oxygen sensors are also used in industrial applications where the environment must lack oxygen. An example is when food is vacuum packed. There are two main categories of oxygen sensors, those which sense oxygen when it is abundantly present (i.e. in air or near an oxygen tank) and those which detect traces of oxygen in ppm. Figure 4 shows a typical circuit used to amplify the output of an oxygen detector. The LPV521 makes an excellent choice for this application as it only draws 345 nA of current and operates on supply voltages down to 1.6V. This application detects oxygen in air. The oxygen sensor outputs a known current through the load resistor. This value changes with the amount of oxygen present in the air sample. Oxygen sensors usually recommend a particular load resistor value or specify a range of acceptable values for the load resistor. Oxygen sensors typically have a life of one to two years. The use of the nanopower LPV521 means minimal power usage by the op amp and it enhances the battery life. With the components shown in Figure 4 the circuit can consume less than 0.5 A of current ensuring that even batteries used in compact portable electronics, with low mAh charge ratings, could last beyond the life of the oxygen sensor. The precision specifications of the LPV521, such as its very low offset voltage, low www.national.com OUTPUT STAGE The LPV521 output voltage swings 3 mV from rails at 3.3V supply, which provides the maximum possible dynamic range at the output. This is particularly important when operating on low supply voltages. The LPV521 Maximum Output Voltage Swing defines the maximum swing possible under a particular output load. The LPV521 output swings 50 mV from the rail at 5V supply with an output load of 100 k. DRIVING CAPACITIVE LOAD The LPV521 is internally compensated for stable unity gain operation, with a 6.2 kHz typical gain bandwidth. However, the unity gain follower is the most sensitive configuration to capacitive load. The combination of a capacitive load placed at the output of an amplifier along with the amplifier's output impedance creates a phase lag, which reduces the phase margin of the amplifier. If the phase margin is significantly reduced, the response will be under damped which causes 18 EMI SUPPRESSION The near-ubiquity of cellular, bluetooth, and Wi-Fi signals and the rapid rise of sensing systems incorporating wireless radios make electromagnetic interference (EMI) an evermore important design consideration for precision signal paths. Though RF signals lie outside the op amp band, RF carrier switching can modulate the DC offset of the op amp. Also some common RF modulation schemes can induce downconverted components. The added DC offset and the induced signals are amplified with the signal of interest and thus corrupt the measurement. The LPV521 uses on chip filters to reject these unwanted RF signals at the inputs and power supply pins; thereby preserving the integrity of the precision signal path. Twisted pair cabling and the active front-end's common-mode rejection provide immunity against low frequency noise (i.e. 60 Hz or 50 Hz mains) but are ineffective against RF interference. Even a few centimeters of PCB trace and wiring for sensors located close to the amplifier can pick up significant 1 GHz RF. The integrated EMI filters of the LPV521 reduce or eliminate external shielding and filtering requirements, thereby increasing system robustness. A larger EMIRR means more rejection of the RF interference. For more information on EMIRR, please refer to AN-1698. 30054555 FIGURE 5. Resistive Isolation of Capacitive Load Recommended minimum values for RISO are given in the following table, for 5V supply. Figure 6 shows the typical response obtained with the CL = 50 pF and RISO = 154 k. The other values of RISO in the table were chosen to achieve similar dampening at their respective capacitive loads. Notice that for the LPV521 with larger CL a smaller RISO can be used for stability. However, for a given CL a larger RISO will provide a more damped response. For capacitive loads of 20 pF and below no isolation resistor is needed. CL RISO 0 - 20 pF not needed 50 pF 154 k 100 pF 118 k 500 pF 52.3 k 1 nF 33.2 k 5 nF 17.4 k 10 nF 13.3 k POWER SUPPLIES AND LAYOUT The LPV521 operates from a single 1.6V to 5.5V power supply. It is recommended to bypass the power supplies with a 0.1 F ceramic capacitor placed close to the V+ and V- pins. Ground layout improves performance by decreasing the amount of stray capacitance and noise at the op amp's inputs and outputs. To decrease stray capacitance, minimize PC board trace lengths and resistor leads, and place external components close to the op amps' pins. 30054580 FIGURE 6. Step Response 19 www.national.com LPV521 peaking in the transfer and, when there is too much peaking, the op amp might start oscillating. In order to drive heavy capacitive loads, an isolation resistor, RISO, should be used, as shown in Figure 5. By using this isolation resistor, the capacitive load is isolated from the amplifier's output. The larger the value of RISO, the more stable the amplifier will be. If the value of RISO is sufficiently large, the feedback loop will be stable, independent of the value of CL. However, larger values of RISO result in reduced output swing and reduced output current drive. LPV521 Physical Dimensions inches (millimeters) unless otherwise noted 5-Pin SC-70 NS Package Number MAA05A www.national.com 20 LPV521 Notes 21 www.national.com LPV521 Nanopower, 1.8V, RRIO, CMOS Input, Operational Amplifier Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage Reference www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Solutions www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic Wireless (PLL/VCO) www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2009 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated