DS13 Series High Performance Solid State Relays For Loads Up To 2A @ 60Vdc Product Facts Standard options: short circuit/overload protection and control status. Optically coupled all solid state relay. TTL & CMOS compatible input. Low on-resistance power MOSFET output. Tested per MIL-PRF-28750D and approved to DSCC drawing 90091. All versions available with Tyco Electronics "W" level screening for CII relays. DS13 series SSRs employ state of the art photovoltaic optical isolation and power MOSFET output chips for ultra-reliable high speed switching of DC loads up to 2 amps, with low on-resistance. Standard options include integral current overload/short circuit protection and a separate input control status line. The overload feature provides protection of the relay, load and load circuit wiring in the event of a sustained current overload or short circuit while the relay is on or when it is turned on into a short. The control CII Part No. DSCC Dwg. No. status provides a built-in test function which provides a logic "0" when the input circuit is energized and functional. The relay is packaged into a custom hermetically sealed lowprofile 8-pin ceramic DIP package, with through hole or surface mount pins. Relay Version DS13-1Y 90091-008 Basic relay DS13-1000 90091-004 Relay w/ short circuit protection DS13-1001 90091-006 Relay w/ control status DS13-1002 90091-002 Relay w/ short circuit protection and control status Notes: Add suffix "S" to part number for surface mount versions. Add suffix "T" to part number for tinned leads. Add suffix "W" to part number for lower screening level. 2 Terminal Input Configuration Direct Drive S1 R Series TTL Drive (+) Output Vcc Load V Load Vcc 4 1 Control 2 Control R Series 1 4 8 5 Return Return Load (-) Output Load Return Load V Load Load Load Return Load V Load Load Load Return 2 5 8 (+) Output (-) Output O C TTL 3 Terminal Input Configuration With Status Without Status V Status R Status Vso Vcc Status (+) Output Output 1 7 (+) Output Load V Load Vcc 4 1 4 8 5 2 V Control Control 2 V Control Control 8 5 Return Load (-) Output Load Return Return (-) Output (c) 2008 by Tyco Electronics Corporation. All Rights Reserved. CII, TE Logo and Tyco Electronics are trademarks. 1 Catalog 8-1773439-9 Revised 3-08 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 31-73-624-6639 High Performance Electronic Products DS13 SSR for loads up to 2A @ 60Vdc (Continued) Environmental Characteristics Electrical Specifications (-55C to +105C unless otherwise specified) Ambient Temperature Range: Operating: -55C to +105C. Storage: -55C to +125C. Input (2 terminal configuration) Vibration Resistance: 100 G's, 10-3,000 Hz. Input supply voltage range (Vcc) 3.8 - 32 Vdc (Notes 1 & 2, Figures 1 & 2) Input current (max.) @ 5Vdc 15mAdc (Notes 1 & 2, Figures 1 & 2) Must turn-on voltage 3.8Vdc Shock Resistance: 1,500 G's, 0.5 ms pulse. Must turn-off voltage 1.5Vdc Reverse voltage protection -32Vdc Constant Acceleration Resistance: 5,000 G's. Input (3 terminal configuration) Control voltage range 0 - 18 Vdc Control current (max.) 240Adc @ 5V, 1mA @ 18V Input supply voltage range (Vcc) 3.8 - 32 Vdc (Notes 1 & 2, Figures 1 & 2) Input current (max.) @ 5Vdc 15mAdc (Notes 1 & 2, Figures 1 & 2) Mechanical Characteristics Must turn-on voltage 0.3Vdc Weight (max.): .07 oz. (2 grams) Must turn-off voltage 3.2Vdc Materials: Case: DIP, hermetically sealed, ceramic Pins: Copper, gold plated Dielectric Strength (min.) I/O 1,000V rms 109 ohms Insulation Resistance (min.) @ 500Vdc Capacitance (max.) 10pF Output Continuous load current (max.) @ 25C, without short circuit protection 2.0Adc (Figure 5, Note 3) Continuous load current (max.) @ 25C, with short circuit protection 1.0Adc (Figure 5, Note 3) Continuous load voltage (max.) 60Vdc Transient blocking voltage (max.) 80Vdc (Note 4) On resistance (max.) @ Tj = 25C, IL = 100ma, with short circuit protection 0.45 ohm (Note 5, Figure 4) On resistance (max.) @ Tj = 25C, IL = 100ma, without short circuit protection 0.22 ohm (Note 5, Figure 4) Output voltage drop (max.), with short circuit protection 0.6Vdc Output voltage drop (max.), without short circuit protection 0.75Vdc Off-state leakage current (max.) @ 60Vdc 100Adc Turn-on time (max.) 1.5 ms (Figure 3) Turn-off time (max.) .25 ms (Figure 3) dv/dt (min.) 100V / s Electrical system spike 600Vdc (Note 4) Junction temperature (max.) 150C Thermal resistance (max.), junction to ambient 80C/W Thermal resistance (max.), junction to case 20C/W Status Status supply voltage 30Vdc Status sink current (max.) @ Vstatus 0.3Vdc 2mAdc (Note 7) Status leakage current (max.) @ 15Vdc 4Adc Short Circuit Protection See Figure 6, Note 7 2 Catalog 8-1773439-9 Revised 3-08 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 31-73-624-6639 High Performance Electronic Products DS13 SSR for loads up to 2A @ 60Vdc (Continued) Figure 1 - Maximum Input Current vs. Input Voltage Figure 2 - Series Resistance vs. Vcc Supply Voltage (Note 1) 2000 15 R Series (ohms) Input Current (mA) 18 12 9 6 1500 1000 500 3 0 0 0 10 15 20 25 30 40 50 5 60 0 5 10 Figure 3 - Output Turn-on and Turn-off Timing High Pin 2 Low V Output Off 90% 10% On Pin 4-5 TOff TOn 25 30 35 Figure 4 - On-Resistance vs. Temperature (Note 6) Normalized On Resistance Factor (NF) Control 20 Vcc (Volts) Input Voltage, Vcc (Vdc) V 15 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 25 50 75 100 125 Junction Temperature (C) Figure 6 - Typical Current Trip Levels 5 2.0 DS13-1Y DS13-1001 1.5 1.0 DS13-1000 DS13-1002 0.5 0.0 -55 15 25 35 45 55 65 75 85 95 105 115 125 Surge Current (amps) Load Current (amps) Figure 5 - Temperature Derating Curve Ambient Temperature (C) 4 3 +25C -55C 2 +105C 1 0 0.01 0.1 1 10 100 1000 Time (seconds) 3 Catalog 8-1773439-9 Revised 3-08 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 31-73-624-6639 High Performance Electronic Products DS13 SSR for loads up to 2A @ 60Vdc (Continued) Figure 7 - Outline Dimensions Through-Hole Mount Version .010 .002 (.25 .05) 6 PLS .560 MAX. (14.22) 8 7 Surface Mount Version .560 MAX. (14.22) 5 8 7 .485 +.010, -.005 .395 MAX. (12.32 +.25, -.13) (10.03) .435 MAX. (11.05) .400 .015 (10.16 .38) 1 2 4 TOP INDEX MARK FOR PIN 1 SIDE INDEX MARK FOR PIN 1 .016 +.010, -.005 (.41 +.25, -.13) 6 PLS .025 (.64) 6 PLS .155 MAX. (3.94) .395 MAX. (10.03) .010 .002 (.25 .05) 6 PLS .155 MAX. (3.94) .036 +.010, -.005 (.91 +.25, -.13) 6 PLS .125 (3.18) .100 (2.54) .125 (3.18) .300 (7.62) 1 4 2 TOP INDEX MARK FOR PIN 1 SIDE INDEX MARK FOR PIN 1 .150 .015 (3.81 .38) 6 PLS .100 (2.54) 5 .300 (7.62) .018 .002 (.46 .05) 6 PLS .018 .002 (.46 .05) 6 PLS Notes 1.2 terminal input configuration is compatible with CMOS or open collector TTL (with pull-up resistor). For Vcc levels above 6Vdc, a series limiting resistor is required. See Fig. 2 for resistor value. Use standard resistor value equal to or less than value form the curve. 2.Vcc = 5Vdc for all tests unless otherwise specified. 3.All DS13 Series relays may drive loads connected to either positive or negative referenced power supply lines. Reversing polarity of output may cause permanent damage. Inductive loads must be diode suppressed. 4.Transient blocking voltage & electrical system spike tests are performed per MIL-STD-704 (28Vdc systems). 5.To determine the maximum on-resistance at any given junction temperature, multiply on-resistance at 25C by normalized on-resistance factor from curve (Fig. 4). 6.Overload testing per MIL-R-28750 is constrained to the limits imposed by the short circuit protection requirements of this specification and DSCC drawing 90091. Load circuit series inductance for "load shorted" mode of operation to be limited to 50mH max. Maximum repetition rate into a shorted load should not exceed 10 Hz. To calculate maximum on-resistance at any temperature, use the following equation: R(on) = R(on) @ 25C x NF (without short circuit protection) and R(on) = 0.2 x NF + .21 (with short circuit protection) where NF = normalized on-resistance factor from Fig. 4. 7.Proper operation of the status feedback requires a status pull-up resistor. Select the status resistor such that it limits status output current to 2mA: R status = V status - 0.3V / 2mA. 8-1773439-9-PDF-KRG-3-08 4 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 31-73-624-6639